Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DOPED MATERIALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of Added Gadolinium Oxide on the Thermal Air Oxidation of Uranium Dioxide

To develop a more reliable and stable UO2-based nuclear fuel, the Pacific Northwest National Laboratory (PNNL) investigated modifying fuel with several soluble lanthanides and zirconium. This article provides the results of these studies investigating gadolinium doping at levels up to 10 mass%. The authors characterized and compared commercially- and PNNL-prepared gadolinium-doped UO2 to determine the oxygen-to-metal ratio, elemental distribution, chemical composition, physical appearance, lattice parameters, and grain structure using atomic force microscopy, scanning electron microscopy coupled with energy dispersive spectroscopy, and X-ray diffractometry. After confirming PNNL-prepared UO2 and (Gd,U)O2 were similar to commercially prepared UO2 and (Gd,U)O2, we measured the thermal behavior of these gadolinium-doped UO2 materials to air oxidation using differential scanning calorimetry and thermogravimetric analysis. Addition of gadolinium stabilized the first oxidation product U4¬O9/U3O7 and slowed the subsequent oxidation to U3O8. Comparison of our measured two-step oxidation of UO2 to U3O8 at 325°C to common gas/solid kinetic reaction models found that each oxidation step is best described as a convolution of kinetic behaviors; the gadolinium insertion into the UO2 lattice enforces a significant alteration in mechanism and oxidation rate. Noticeable changes in mechanism become apparent between 1% and 3% gadolinium content.

Uranium Dioxide, Gadolinium Oxide, Thermal Air Oxi↗
DOE OSTI2021

AlCl 3 -Dosed Si(100)-2 × 1: Adsorbates, Chlorinated Al Chains, and Incorporated Al

The adsorption of AlCl 3 on Si(100) and the effect of annealing the AlCl 3 -dosed substrate were studied to reveal key surface processes for the development of atomic-precision, acceptor-doping techniques. This investigation was performed via scanning tunneling microscopy (STM), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) calculations. At room temperature, AlCl 3 readily adsorbed to the Si substrate dimers and dissociated to form a variety of species. Annealing the AlCl 3 -dosed substrate at temperatures below 450 °C produced unique chlorinated aluminum chains (CACs) elongated along the Si(100) dimer row direction. An atomic model for the chains is proposed with supporting DFT calculations. Al was incorporated into the Si substrate upon annealing at 450 °C and above, and Cl desorption was observed for temperatures beyond 450 °C. Al-incorporated samples were encapsulated in Si and characterized by secondary ion mass spectrometry (SIMS) depth profiling to quantify the Al atom concentration, which was found to be in excess of 10 20 cm –3 across a ~2.7 nm-thick δ-doped region. Here, the Al concentration achieved here and the processing parameters utilized promote AlCl 3 as a viable gaseous precursor for novel acceptor-doped Si materials and devices for quantum computing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Emergence of superconductivity in doped multiorbital Hubbard chains

Abstract We introduce a variational state for one-dimensional two-orbital Hubbard models that intuitively explains the recent computational discovery of pairing in these systems when hole doped. Our ansatz is an optimized linear superposition of Affleck–Kennedy–Lieb–Tasaki valence-bond states, rendering the combination a valence-bond liquid dubbed orbital resonant valence bond. We show that the undoped (one-electron/orbital) quantum state of two sites coupled into a global spin singlet is exactly written employing only spin-1/2 singlets linking orbitals at nearest-neighbor sites. Generalizing to longer chains defines our variational state visualized geometrically expressing our chain as a two-leg ladder, with one orbital per leg. As in Anderson’s resonating valence-bond state, our undoped variational state contains preformed singlet pairs that via doping become mobile, leading to superconductivity. Doped real materials with one-dimensional substructures, two near-degenerate orbitals, and intermediate Hubbard U / W strengths— W the carrier’s bandwidth—could realize spin-singlet pairing if on-site anisotropies are small. If these anisotropies are robust, spin-triplet pairing emerges.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Mechanistic insights into metal, nitrogen doped carbon catalysts for oxygen reduction: progress in computational modeling

We report metal and nitrogen doped carbon materials (denoted as M–N–C) synthesized through high-temperature pyrolysis have been found to exhibit activity for oxygen reduction reaction (ORR) approaching that of Pt and electrochemical stability higher than previous MN 4 -containing macrocyclic molecular catalysts. Tremendous efforts have thus been devoted to the advancement of M–N–C catalysts as an economical alternative to Pt-based catalysts for proton exchange membrane fuel cell cathodes with a focus on simultaneously improving activity and stability. To this end, novel computational modeling techniques have been developed and applied to acquire knowledge crucial for accelerating the pace of M–N–C catalyst development. In this review, recent progress in computational method development, as well as the predictions of chemical structure of active sites, reaction pathways, ORR kinetics, and catalyst stability in electrochemical environments, are critically surveyed. Moreover, the crucial role of computational modeling to elucidate the functional mechanism of M–N–C catalysts for ORR in acid media and enable rational design of M–N–C catalysts is discussed with a visionary outlook for the field.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

(Cd,Mg)Te crystals for picosecond-response optical-to-x-ray radiation detectors

We demonstrate a photodetector sensitive to both optical and x-ray picosecond pulses based on our in-house grown cadmium magnesium telluride (Cd,Mg)Te single crystal. Specifically, we developed In-doped Cd0.96Mg0.04Te material and discuss its femtosecond optical photoresponse, as well as the detector performance, such as <100-pA dark current and up to 0.22-mA/W responsivity for 780-nm wavelength optical radiation. The detector exposed to Ti fluorescence (K alpha) x-ray pulses at 4.5 keV, generated by a free-electron laser beam with the central energy of 9.8 keV and <100 fs pulse width, exhibited readout-electronics-limited 200-ps full-width-at-half-maximum photoresponse, demonstrating that it is suitable for coarse timing in free-electron laser x-ray/optical femtosecond pump–probe spectroscopy applications.

Instruments & Instrumentation↗
DOE OSTI2020

Optomechanical interaction in fibre lasers with micro-optomechanical resonance structures

We report the results of studies of fibre lasers with passive modulators based on light-excited micro-optomechanical resonance structures (micro-oscillators). It is shown that in fibre lasers based on active fibres doped with rare-earth elements (Er, Er/Yb, Yb, Nd), the optomechanical interaction of laser radiation with micro-oscillators of various types (fibre-optic, microvolume) leads to self-oscillations of the characteristics of laser radiation at frequencies of relaxation oscillations and intermode beats synchronised with the frequencies of elastic eigenoscillations of micro-oscillators. It is found that in an ultra-long erbium – ytterbium fibre laser with a nonlinear mirror based on a microcantilever, laser photothermal excitation of the second mode of elastic transverse oscillations of the microcantilever makes it possible to perform passive mode locking exclusively due to Q-switching of the laser cavity. Pulsed lasing with a controlled repetition rate (∼76 kHz), a pulse duration of 2 – 5 μs and an output energy of 0.1 μJ per pulse is implemented. Based on a simplified physical model of the indicated fibre lasers with micro-oscillators, we have developed an approximate mathematical model describing the regimes of passive mode locking of fibre lasers with micro-oscillators that play the role of mirrors with a nonlinear reflection coefficient in the laser cavity. The prospects for the development and application of the considered laser systems are discussed. (control of laser radiation parameters)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Control over pulsed operation modes of an erbium-doped fibre laser passively mode-locked via nonlinear polarisation rotation

We have experimentally demonstrated the possibility of controlling pulse generation modes of an erbium-doped fibre ring laser operating in the anomalous dispersion regime and passively mode-locked via nonlinear polarisation rotation. It has been shown that individual adjustment of the pump power and intracavity polarisation controllers leads to changes in pulse generation mode, without changing the cavity. We have evaluated the key spectral, temporal and energetic characteristics of the observed pulse generation modes. (control of laser radiation parameters. active media)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Experimental and theoretical description of the process of contact laser surgery with a titanium-doped optothermal fibre converter

In an in vitro experiment simulating a surgeon’s actions in the process of contact laser surgery of soft biological tissue, the dependences of the temperature of a titanium-doped optothermal fibre converter (TOTFC) and the depths of coagulation and ablation of biological tissue on the average radiation power of a diode laser with a wavelength of 980 nm and on the speed of the converter movement along biological tissue are obtained. The structural, optical, and thermophysical models of TOTFC are discussed, as well as the thermophysical model of the interaction of a laser-heated converter with biological tissue, which takes into account the temperature dependences of the basic thermophysical parameters of the converter and biological tissue, as well as the contribution of the thickness h{sub int} of the water vapour layer between the converter and biotissue. It is shown that the proposed model allows describing the result of contact laser surgery of soft biotissue with TOTFC adequately to the experiment. (laser biophotonics)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

The influence of waveguide doping on the output characteristics of AlGaAs/GaAs lasers

The influence of doping of waveguide layers on the output characteristics of lasers based on AlGaAs/GaAs double separate-confinement heterostructures is analysed. The heterostructures with narrow and broadened waveguides are studied. Samples of laser diode bars with undoped and doped waveguide layers are experimentally fabricated and compared. It is shown that the latter type of structures with a broadened waveguide allows one to increase the output power of the laser diode bars by 10 % – 15 %, all other conditions being equal. (lasers. control of laser radiation parameters)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Spectroscopic study of GdVO{sub 4} : Yb + Er crystals

GdVO{sub 4} crystals doped with different erbium and ytterbium concentrations have been grown in order to study their spectroscopic and kinetic properties and identify the nature of active centres in them. Their polarised transmission and luminescence spectra have been used to construct energy level diagrams of the Er{sup 3+} ion. The lifetime of the lower level of the {sup 4}I{sub 11/2} excited-state multiplet has been shown to decrease markedly with increasing ytterbium concentration. Inequivalent erbium centres have been observed to form in the crystals with increasing ytterbium concentration. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Homogeneous broadening in the spectrum of a broadband erbium-doped fibre light source

Interference of wave trains separated out in an inhomogeneous emission spectrum of a superluminescent erbium-doped fibre source has been studied by scanning the wavelength of a spectrum analyser. The results demonstrate that, as the spectral resolution of the spectrum analyser decreases to a level corresponding to a sharp drop in interference fringe visibility relative to its original level, near 100 %, fringe visibility becomes dependent on the wavelength in the inhomogeneous spectrum of the source. The reason for this is that, at some characteristic resolution δλ (δλ > 0.5 nm in our case), the coherence time of wave trains is not limited by the spectral resolution of the spectrum analyser and is related to the inhomogeneous spectrum of the source, whose limiting width can be thought of as the homogeneous linewidth in the spectrum of the source. This feature can be used for evaluating homogeneous line broadening. (paper)

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Radiofrequency synthesiser with an intrinsic instability of 5 × 10{sup −15} at the averaging time of 1 s based on a femtosecond erbium-doped fibre laser

A radio-optical synthesiser intended for operation in a radio-frequency master oscillator with an optical He – Ne/CH{sub 4} frequency standard (λ = 3.39 μm) is developed on the basis of a femtosecond erbium-doped fibre laser. The synthesiser generates equidistant harmonics in the frequency range of 1 – 10 GHz with stability determined by the optical frequency standard. A stable supercontinuum spectrum is formed in the range around 1.06 μm, which provides stable 24-hour operation of the synthesiser and is important for practical applications in off-laboratory conditions. A direct comparison of the output frequencies of two synthesisers shows that the up-grade of the fibre laser and detection system of femtosecond pulses results in the synthesiser intrinsic instability of 5 × 10{sup −15} at the averaging time of 1 s. Such a value is by an order of magnitude less than that obtained in our earlier works. (laser frequency standards)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Optimization of Ag Electrocatalyst Performance for CO2 to CO Conversion: Pairing Atomic Simulations with Experiments

Density-functional theory- based calculations that complement our series of experimental efforts on optimizing Ag electrocatalyst performance for CO2 to CO conversion were presented. Three key findings are drawn out from the combined UHV surface science, STM and electrochemical measurements: (1) Using a series of Ag nanoparticles with 2-6 nm average diameters, CO2 reduction reaction (CO2RR) activity increases, with particle between 2 nm and ∼4 nm demonstrating the highest combination of activity and selectivity; (2) Electronic metal−support interactions (EMSIs) between Ag and C dramatically improve CO2RR performance as evidenced by a scaling relationship between particle size and the relative Ag−C EMSIs strength, which improves the CO2-to-CO Faradaic efficiency of sub-2 nm Ag particles from 2 to ∼100% and increases the CO turnover frequency ∼15-fold compared with similarly sized bare Ag particles; (3) The performance Ag electrocatalysts is improved when supported on S-doped C materials. Computational modeling of 1−10 nm Ag particles predicts a nearly identical size-dependent trend with maximum CO2RR activity predicted for 3.7nm particles. The calculations support the promotional effect of C materials, showing a large charge transfer of 1.02 e from Ag clusters to defective C and a 0.41 eV less endergonic step of forming COOH intermediate on Ag/defective-C compared to the Ag/C system. Calculations indicate a more favorable energetic pathway of CO2-to-CO at the C-S-Ag interface, consistent with experiments.

CO2 utilization↗
DOE OSTI2020

Advancement of Commercial Intumescent Expanding Foams for Deactivation and Decommissioning in the Nuclear Sector - 20198

Florida International University (FIU), in collaboration with The Department of Energy's Office of Environmental Management (DOE-EM), Savannah River National Laboratory (SRNL), and sites across the Savannah River complex, have identified an operational requirement for a fixative technology that is intended to immobilize and/or isolate residual contamination within a 3-dimensional space. Fixation of radiological contamination can reduce worker risk and mitigate potentially hazardous conditions, however nearly every marketed contamination fixative has been found to be flammable; a significant concern in radiological facilities. Coupled with this, industry fixatives are normally used as a thin coating which can present problems when attempting to stabilize irregular geometry or areas that are difficult to access whilst ensuring full coverage. The technical evaluation and advancement of commercial-off-the-shelf (COTS) polyurethane foams has yielded a down-selected candidate that shows potential in meeting the requirements to support deactivation and decommissioning activities. Several performance criteria have been established and tested to progress the technology readiness level towards an active field demonstration (TRL-7). Such criteria include: mechanical failure limits, adhesive and cohesive properties, thermal/fire resilience, determining thermal behavior, ability to immobilize contamination, and a means of non-destructive evaluation of applications. The test scenario examined was targeted towards an application for decommissioning nuclear pipework, in which the down-selected polyurethane foam would act as a barrier to segregate pipework and mitigate the potential for release during cutting, packaging, and storage operations. Testing carried out at SRNL included: mechanical evaluation of tensile, compressive, and adhesion strength by dynamic mechanical analysis (DMA), as well as thermogravimetric analysis (TGA). FIU examined the foam's fixative properties by utilizing phosphorescent europium-dysprosium doped strontium aluminate powder to investigating the extent to which contamination can be immobilized. FIU has also exploited previous successes in the field of intumescent technologies to assess the down-selected foam's tolerance to an extreme fire scenario, while maintaining the ability to effectively mitigate a contamination release. Parallel to this, extensive thermal investigations were carried out to determine the upper boundary of anticipated heat generation during the curing process as heat generation has the potential to compromise rubber parts of contaminated enclosures. These investigations subsequently yielded a promising method for a non-destructive application evaluation by means of infrared thermography. Utilizing the high sensitivity of modern IR cameras, coupled with the heat generated during the curing process of the polyurethane foam, FIU has been exploring the concept of monitoring the external pipe surface for indications of an irregular or abnormal application, thus informing operational decision making. The testing carried out utilized several current 'best fit' ASTM standards, which serve as helpful guidelines for testing, however, a precise definition of the operational parameters and requirements is still necessary. With continued collaboration with SRNL, FIU aims refine said definitions and develop new standards by which this, and other decommissioning technologies, can be accredited by relevant standards based testing. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Leveraging Sequential Doping of Semiconducting Polymers to Enable Functionally Graded Materials for Organic Thermoelectrics

With the ability to modulate electronic properties through molecular doping coupled with ease in processability, semiconducting polymers are at the forefront in enabling organic thermoelectric devices for thermal energy management. In contrast to uniform thermoelectric material properties, an alternative route focuses on functionally graded materials (FGMs) where one spatially controls and optimizes transport properties across the length of a thermoelectric material. While primarily studied in the context of inorganic materials, the concept of FGMs for organic thermoelectrics has not been explored. Herein, we introduce how molecular doping of semiconducting polymers enables spatial compositional control of thin-film FGMs. Specifically, we utilize sequential vapor doping of poly[2,5-bis(3-tetradecylthiophen-2-yl) thieno [3,2-b]thiophene] (PBTTT) with the small molecule acceptor 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) to fabricate the simplest form of FGMs – double- segmented thin films. The two thin-film segments are of equal length (7.5 mm), but each set to different doping levels. Our study focuses on understanding the thermoelectric properties (Seebeck coefficient, α, and electronic conductivity, σ) and structural properties (through X-ray scattering, UV-vis-NIR spectroscopy, and Raman spectroscopy) within and across the two segments. We observe the presence of a small diffuse interfacial region of 0.5 – 1 mm between the two segments where the doping level and transport properties vary continuously. Despite the diffuse interface, the measured effective Seebeck coefficient (αeff) across the two segments is simply the average of α within each segment. Importantly, this experimental result is consistent with reported mathematical models describing αeff in graded thermoelectric materials. Finally, our results demonstrate the facile fabrication and characterization of functionally graded organic thermoelectric materials, providing guidelines for further development on more complex FGMs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Spatially Enhanced Electrostatic Doping in Graphene Realized via Heterointerfacial Precipitated Metals

Forming heavily-doped regions in 2D materials, like graphene, is a steppingstone to the design of emergent devices and heterostructures. Here, a selective-area approach is presented to tune the work-function and carrier density in monolayer graphene by spatially synthesizing sub-monolayer gallium beneath the 2D-solid. The localized metallic gallium is formed via precipitation from an underlying diamond-like carbon (DLC) film that is spatially implanted with gallium-ions. By controlling the interfacial precipitation process with annealing temperature, spatially precise ambipolar tuning of the graphene work-function is achieved, and the tunning effect preserved upon cooling to ambient conditions. Consequently, charge carrier densities from ≈1.8 × 10 10 cm -2 (hole-doped) to ≈7 × 10 13 cm -2 (electron-doped) are realized, confirmed by in situ and ex situ measurements. The theoretical studies corroborated the role of gallium at the heterointerface on charge transfer and electrostatic doping of the graphene overlayer. Specifically, sub-monolayer gallium facilitates heavy n-doping in graphene. Extending this doping strategy to other implantable elements in DLC provides a new means of exploring the physics and chemistry of highly-doped 2D materials.

36 MATERIALS SCIENCE↗