Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIRECT CURRENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Electrical measurements in the atmosphere and the Ionosphere over an active thunderstorm. II - Direct current electric fields and conductivity

On August 9, 1981, a series of three rockets was launched over an air mass thunderstorm off the eastern seaboard of Virginia while simultaneous stratospheric and ground-based electric field measurements were made. The conductivity was substantially lower at most altitudes than the conductivity profiles used by theoretical models. Direct current electric fields over 80 mV/m were measured as far away as 96 km from the storm in the stratosphere at 23 km altitude. No dc electric fields above 75 km altitude could be identified with the thunderstorm, in agreement with theory. However, vertical current densities over 120 pA/sq m were seen well above the classical 'electrosphere' (at 50 or 60 km). Frequent dc shifts in the electric field following lightning transients were seen by both balloon and rocket payloads. These dc shifts are clearly identifiable with either cloud-to-ground (increases) or intercloud (decreases) lightning flashes.

Holzworth, R. H.↗
DOE OSTI2012

Open-air direct current plasma jet: Scaling up, uniformity, and cellular control

Atmospheric-pressure plasma jets are commonly used in many fields from medicine to nanotechnology, yet the issue of scaling the discharges up to larger areas without compromising the plasma uniformity remains a major challenge. In this paper, we demonstrate a homogenous cold air plasma glow with a large cross-section generated by a direct current power supply. There is no risk of glow-to-arc transitions, and the plasma glow appears uniform regardless of the gap between the nozzle and the surface being processed. Detailed studies show that both the position of the quartz tube and the gas flow rate can be used to control the plasma properties. Further investigation indicates that the residual charges trapped on the inner surface of the quartz tube may be responsible for the generation of the air plasma plume with a large cross-section. The spatially resolved optical emission spectroscopy reveals that the air plasma plume is uniform as it propagates out of the nozzle. The remarkable improvement of the plasma uniformity is used to improve the bio-compatibility of a glass coverslip over a reasonably large area. This improvement is demonstrated by a much more uniform and effective attachment and proliferation of human embryonic kidney 293 (HEK 293) cells on the plasma-treated surface.

42 ENGINEERING↗
DOE OSTI2022

Electric Grid Supply Chain Review: Large Power Transformers and High Voltage Direct Current Systems

The report “America’s Strategy to Secure the Supply Chain for a Robust Clean Energy Transition” lays out the challenges and opportunities faced by the United States in the energy supply chain as well as the federal government plans to address these challenges and opportunities. It is accompanied by several issue-specific deep dive assessments, including this one, in response to Executive Order 14017 “America’s Supply Chains,” which directs the Secretary of Energy to submit a report on supply chains for the energy sector industrial base. The Executive Order is helping the federal government to build more secure and diverse U.S. supply chains, including energy supply chains. The need to modernize and increase the capacity of the U.S. power grid is increasing due to growing population, aging infrastructure, grid resilience requirements, operational flexibility needs, and a growing portfolio of renewable energy. As part of the Paris Climate Agreement the United States has committed to reducing its net greenhouse gas emissions by 50 to 52 percent below 2005 levels in 2030 and has set a goal of 100 percent carbon pollution free electricity by 2035 (The United States of America Nationally Determined Contribution, 2021). Meeting these targets will require a significant expansion of the power system to integrate a large amount of new renewable resources (United States Department of State & United States Executive Office of the President, 2021). However, many critical components supporting the power grid have limited to no domestic manufacturing capacity and face complex challenges in supporting a rapid expansion of the grid to meet multiple objectives, including decarbonization goals. This report focuses on two key grid components: large power transformers (LPTs) and high-voltage direct current (HVDC) transmission.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Combinatorial Deposition of Ultrathick Ta-W-Au-Bi High-Entropy Alloys for Next-Generation Hohlraums by Direct-Current Magnetron Sputtering

Hohlraum temperature calculations with the model by J. H. Hammer and M. D. Rosen predict a higher X-ray drive from Ta-W-Au-Bi high-entropy alloys compared to pure Au and recently developed Ta 4 Au and Au-Bi hohlraums. Here, we study the microstructure and properties of 25-75−µm-thick Ta-W-Au-Bi alloy films deposited via combinatorial direct-current magnetron sputtering. All of the films have promising physical properties, including high electrical resistivity, that satisfy the requirements for magnetically assisted inertial confinement fusion experiments. While porosity tends to increase with increasing Bi content, we also found that films with Bi content > 44 at. % exhibited densification close to the substrate/film interface and formed a single-phase alloy. In conclusion, these findings provide a potential path forward for the development of Ta-W-Au-Bi alloys for next-generation hohlraum materials.

Magnetron sputtering↗
DOE OSTI2025

High-rate deposition of ultrathick bismuth films by direct-current magnetron sputtering

Bismuth coatings deposited at room temperature by physical vapor deposition typically feature irregularly-shaped grains and a high density of voids, thereby preventing their use in many potential applications. Here, we demonstrate the deposition of low-stress, high-density 40-μm-thick Bi films by systematically studying the effect of the deposition rate and substrate tilt on the properties of Bi films deposited at room temperature by direct-current magnetron sputtering. Furthermore, results show that, with increasing deposition rate, the morphology, structure, and properties of Bi films greatly improve, while an increase in substrate tilt leads to a monotonic decrease in film thickness, density, and electrical conductivity.

Bismuth↗
DOE OSTI2016

High performance mid-temperature selective absorber based on titanium oxides cermet deposited by direct current reactive sputtering of a single titanium target

This paper reports the design and fabrication of a new double cermet-based low-mid temperature solar selective absorber based on TiO x cermet layers, which were deposited with a single Ti target by varying O 2 partial pressure in sputtering chamber as reactive gas. High metal volume fraction cermet 1 and low metal volume fraction cermet 2 were deposited with O 2 partial pressure of 0.15 mTorr and 0.25 mTorr, respectively, with direct current power density of 6.58 W cm -2 . The complex refractive indices from ellipsometry were used to design solar selective absorber. The reflectance, thermal stability, and morphology were studied in absorbers on Cu and stainless steel. The effect of TiO 2 and SiO 2 as anti-reflective coating layers was investigated. Finally, the absorber on Cu substrate has high absorptance of 90.8% and low emittance of 4.9% (100 °C), and changed to 96.0% and 6.6%, respectively, after annealing at 300 °C for 4 days.

42 ENGINEERING↗
DOE OSTI2017

Optical gain in colloidal quantum dots achieved with direct-current electrical pumping

Chemically synthesized semiconductor quantum dots (QDs) can potentially enable solution-processable laser diodes with a wide range of operational wavelengths, yet demonstrations of lasing from the QDs are still at the laboratory stage. An important challenge—realization of lasing with electrical injection—remains unresolved, largely due to fast nonradiative Auger recombination of multicarrier states that represent gain-active species in the QDs. Here in this paper, we present population inversion and optical gain in colloidal nanocrystals realized with direct-current electrical pumping. Using continuously graded QDs, we achieve a considerable suppression of Auger decay such that it can be outpaced by electrical injection. Further, we apply a special current-focusing device architecture, which allows us to produce high current densities (j) up to ~18 A cm -2 without damaging either the QDs or the injection layers. The quantitative analysis of electroluminescence and current-modulated transmission spectra indicates that with j = 3-4 A cm -2 we achieve the population inversion of the band-edge states.

36 MATERIALS SCIENCE↗
DOE OSTI2016

The direct-current response of electrically conducting fractures excited by a grounded current source

Hydraulic fracture stimulation of low permeability reservoir rocks is an established and cross–cutting technology for enhancing hydrocarbon production in sedimentary formations and increasing heat exchange in crystalline geothermal systems. Whereas the primary measure of success is the ability to keep the newly generated fractures sufficiently open, long–term reservoir management requires a knowledge of the spatial extent, morphology, and distribution of the fractures — knowledge primarily informed by microseismic and ground deformation monitoring. To minimize the uncertainty associated with interpreting such data, we investigate through numerical simulation the usefulness of direct-current (DC) resistivity data for characterizing subsurface fractures with elevated electrical conductivity by considering a geophysical experiment consisting of a grounded current source deployed in a steel cased borehole. In doing so, the casing efficiently energizes the fractures with steady current. Finite element simulations of this experiment for a horizontal well intersecting a small set of vertical fractures indicate that the fractures manifest electrically in (at least) two ways: (1) a local perturbation in electric potential proximal to the fracture set, with limited farfield expression and (2) an overall reduction in the electric potential along the borehole casing due to enhanced current flow through the fractures into the surrounding formation. The change in casing potential results in a measurable effect that can be observed far from fractures themselves. Under these conditions, our results suggest that farfield, timelapse measurements of DC potentials can be interpreted by simple, linear inversion for a Coulomb charge distribution along the borehole path, including a local charge perturbation due to the fractures. As a result, this approach offers an inexpensive method for detecting and monitoring the time-evolution of electrically conducting fractures while ultimately providing an estimate of their effective conductivity — the latter providing an important measure independent of seismic methods on fracture shape, size, and hydraulic connectivity.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2014

J-R Curve Determination for Disk-shaped Compact Specimens Based on the Normalization Method and Direct Current Potential Drop Technique

Material ductile fracture toughness can be described by J-integral versus crack extension relationship (J-R curve). As a conventional J-R curve measurement method, unloading compliance (UC) becomes impractical in elevated temperature testing due to relaxation of the material and a friction induced back-up shape of the J-R curve. In addition, the UC method may underpredict the crack extension for standard disk-shaped compact (DC(T)) specimens. In order to address these issues, the normalization method and direct current potential drop (DCPD) technique were applied for determining J-R curves at 24 C and 500 C for 0.18T DC(T) specimens made from type 316L stainless steel. For comparison purchase, the UC method was also applied in 24 C tests. The normalization method was able to yield valid J-R curves in all tests. The J-R curves from the DCPD technique need adjustment to account for the potential drop induced by plastic deformation, crack blunting, etc. and after applying a newly-developed DCPD adjustment procedure, the post-adjusted DCPD J-R curves essentially matched J-R curves from the normalization method. In contrast, the UC method underpredicted the crack extension in all tests resulting in substantial deviation in the derived J-R curves manifested by high Jq values than the normalization or DCPD method. Only for tests where the UC method underpredicted the crack extension by a very small value, J-R curves determined by the UC method were similar to those determined by the normalization or DCPD method.

DCPD↗
DOE OSTI2018

Percolative nature of the direct-current paraconductivity in cuprate superconductors

Abstract Despite extraordinary scientific efforts over the past three decades, the cuprate high-temperature superconductors continue to pose formidable challenges. A pivotal problem, essential for understanding both the normal and superconducting states, is to clarify the nature of the superconducting pre-pairing above the bulk transition temperature T c . Different experimental probes have given conflicting results, in part due to difficulties in discerning the superconducting response from the complex normal-state behavior. Moreover, it has proven challenging to separate common properties of the cuprates from compound-specific idiosyncrasies. Here we investigate the paraconductivity—the superconducting contribution to the direct-current (dc) conductivity—of the simple-tetragonal model cuprate material HgBa 2 CuO 4+ δ . We are able to separate the superconducting and normal-state responses by taking advantage of the Fermi-liquid nature of the normal state in underdoped HgBa 2 CuO 4+ δ ; the robust and simple quadratic temperature-dependence of the normal-state resistivity enables us to extract the paraconductivity above the macroscopic T c with great accuracy. We find that the paraconductivity exhibits unusual exponential temperature dependence, and that it can be quantitatively explained by a simple superconducting percolation model. Consequently, the emergence of superconductivity in this model system is dominated by the underlying intrinsic gap inhomogeneity. Motivated by these insights, we reanalyze published results for two other cuprates and find exponential behavior as well, with nearly the same characteristic temperature scale. The universal intrinsic gap inhomogeneity is not only essential for understanding the supercoducting precursor, but will also have to be taken into account in the analysis of other bulk measurements of the cuprates.

Popčević, Petar↗
NASA NTRS1990

Impulsive phase heating by uni-directional current systems in solar flares

The possibility of producing rapid heating of a substantial coronal volume by current dissipation, driven by a tearing instability associated with a single unidirectional current system, is investigated. For the fast tearing mode, it is found that, for initial growth rates gamma(f) equal or less than 0.3/s, the electron heating is offset by convective losses, resulting in a very slow temperature rise, and hard X-ray emitting temperatures are never realized. For the larger growth rates, heating from 10 to the 7th to 10 to the 8th K can be achieved in a few seconds; however, in this regime, the maximum volume heated is some three to five orders of magnitude less than the volume of heated material that is inferred from hard X-ray emission measures. The results suggest that to achieve the required heating for the fast tearing mode, a more complicated geometry involving multiple small-scale, oppositely directed current channels may be necessary.

La Rosa, T. N.↗
DOE OSTI2016

Self-deformation in a direct current driven helium jet micro discharge

We report on the experimental observation of three dimensional self-deformation in an atmospheric micro discharge of the helium microjet through a tube into the ambient air upon a water electrode. The geometry of the discharge system is axial symmetric. While decreasing the discharge current, three dimensional collective motion of plasma filaments is directly observed. The three dimensional configuration of the discharge self changed from an axial symmetrical horn to a rectangular horn when the water acts as a cathode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2014

Differences between direct current and alternating current capacitance nonlinearities in high-k dielectrics and their relation to hopping conduction

Capacitance nonlinearities were studied in atomic layer deposited HfO{sub 2} films using two types of signals: a pure ac voltage of large magnitude (ac nonlinearities) and a small ac voltage superimposed to a large dc voltage (dc nonlinearities). In theory, ac and dc nonlinearities should be of the same order of magnitude. However, in practice, ac nonlinearities are found to be an order of magnitude higher than dc nonlinearities. Besides capacitance nonlinearities, hopping conduction is studied using low-frequency impedance measurements and is discussed through the correlated barrier hopping model. The link between hopping and nonlinearity is established. The ac nonlinearities are ascribed to the polarization of isolated defect pairs, while dc nonlinearities are attributed to electrode polarization which originates from defect percolation paths. Both the ac and dc capacitance nonlinearities display an exponential variation with voltage, which results from field-induced lowering of the hopping barrier energy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2013

Investigation of band offsets and direct current leakage properties of nitrogen doped epitaxial Gd{sub 2}O{sub 3} thin films on Si

Dielectric properties of epitaxial Gd{sub 2}O{sub 3} thin films grown on Si have been found to improve significantly by incorporation of suitable dopants. However, in order to achieve optimum electrical properties from such doped oxides, it is important to understand the correlation between doping and the electronic structure of the material. In the present article, we report about the effect of nitrogen doping on the electronic structure and room temperature dc leakage properties of epitaxial Gd{sub 2}O{sub 3} thin films. Epitaxial Gd{sub 2}O{sub 3}:N thin films were grown on p-type Si (111) substrates by solid source molecular beam epitaxy technique using molecular N{sub 2}O as the nitridation agent. First investigations confirmed the presence of substitutional N in the Gd{sub 2}O{sub 3}:N layers. Incorporation of nitrogen did not affect the structural quality of the oxide layers. X ray photoelectron spectroscopy investigations revealed band gap narrowing in epitaxial Gd{sub 2}O{sub 3} due to nitrogen doping, which leads to reduction in the valence band offset of the Gd{sub 2}O{sub 3}:N layers with Si. DC leakage current measured at room temperature revealed that despite reduction in the band gap and valence band offsets due to N doping, the Gd{sub 2}O{sub 3}:N layers remain sufficiently insulating. A significant reduction of the leakage current densities in the Gd{sub 2}O{sub 3}:N layers with increasing nitrogen content suggests that doping of epitaxial Gd{sub 2}O{sub 3} thin films with nitrogen can be an effective route to eliminate the adverse effects of the oxygen vacancy induced defects in the oxide layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Direct current injection and thermocapillary flow for purification of aligned arrays of single-walled carbon nanotubes

Aligned arrays of semiconducting single-walled carbon nanotubes (s-SWNTs) represent ideal configurations for use of this class of material in high performance electronics. Development of means for removing the metallic SWNTs (m-SWNTs) in as-grown arrays represents an essential challenge. Here, we introduce a simple scheme that achieves this type of purification using direct, selective current injection through interdigitated electrodes into the m-SWNTs, to allow their complete removal using processes of thermocapillarity and dry etching. Experiments and numerical simulations establish the fundamental aspects that lead to selectivity in this process, thereby setting design rules for optimization. Single-step purification of arrays that include thousands of SWNTs demonstrates the effectiveness and simplicity of the procedures. The result is a practical route to large-area aligned arrays of purely s-SWNTs with low-cost experimental setups.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2014

Comparison of direct current and 50 Hz alternating current microscopic corona characteristics on conductors

Corona discharge is one of the major design factors for extra-high voltage and ultra-high voltage DC/AC transmission lines. Under different voltages, corona discharge reveals different characteristics. This paper aims at investigating DC and AC coronas on the microscopic scale. To obtain the specific characteristics of DC and AC coronas, a new measurement approach that utilizes a coaxial wire-cylinder corona cage is designed in this paper, and wires of different diameters are used in the experiment. Based on the measurements, the respective microscopic characteristics of DC and AC coronas are analyzed and compared. With differences in characteristics between DC and AC coronas proposed, this study provides useful insights into DC/AC corona discharges on transmission line applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2014

The physical nature of the phenomenon of positive column plasma constriction in low-pressure noble gas direct current discharges

The essence of the positive-column plasma constriction for static (the diffusion mode) and dynamic ionization equilibrium (the stratificated and constricted modes) is analyzed. Two physical parameters, namely, the effective ionization rate of gas atoms and the ambipolar diffusion coefficient of electrons and ions, determine the transverse distribution of discharge species and affect the current states of plasma. Transverse constriction of the positive column takes place as the gas ionization level (discharge current) and pressure increase. The stratified mode (including the constricted one) is observed between the two adjacent types of self-sustained discharge phases when they coexist together at the same time or in the same place as a coherent binary mixture. In the case, a occurrence of the discharge phase with more high electron density presently involve a great decrease in the cross-section of the current channel for d.c. discharges. Additional physical factors, such as cataphoresis and electrophoresis phenomena and spatial gas density inhomogeneity correlated with a circulatory flow in d.c. discharges, are mainly responsible for the current hysteresis and partially constricted discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Phenomena of oscillations in atmospheric pressure direct current glow discharges

Self-sustained oscillations in a dc glow discharge with a semiconductor layer at atmospheric pressure were investigated by means of a one-dimensional fluid model. It is found that the dc glow discharge initially becomes unstable in the subnormal glow region and gives rise to oscillations of plasma parameters. A variety of oscillations with one or more frequencies have been observed under different conditions. The discharge oscillates between the glow discharge mode and the Townsend discharge mode in the oscillations with large amplitude while operates in the subnormal glow discharge mode all the while in the oscillations with small amplitude. Fourier Transform spectra of oscillations reveal the transition mechanism between different oscillations. The effects of semiconductor conductivity on the oscillation frequency of the dominant mode, gas voltage, as well as the discharge current have also been analyzed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗