Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

RidgeAlloy: A high pressure die casting alloy that captures the approaching wave of automotive body sheet scrap

Oak Ridge National Laboratory (ORNL) has recently launched an effort to economically expand the North American aluminum supply chain by designing and developing a new family of Al-Mg-Si-Fe-Mn structural die cast aluminum alloys that can be made from up to 100% mixed 5xxx and 6xxx series automotive post-consumer sheet scrap and do not require heat treatment. The goal is to develop an alloy capable of capturing the approaching scrap wave of aluminum sheet intensive vehicles (in the 2030’s) into integrated structural high pressure die castings, rather than down-cycling these high-grade sheet alloys into non-structural castings. ORNL discovered a significant gap in the commercial thermodynamic databases that were unable to predict the trends of a key primary intermetallic phase as a function of composition. Experiments were performed to correct this gap and to create a unique, corrected quaternary database for Al-Mg-Si-Fe. High throughput computational methods, including solidification simulations, were used to identify a composition volume capable of avoiding this embrittling primary intermetallic phase, even at higher Fe + Si contents. Laboratory scale castings validated the thermodynamic and solidification predictions and resulted in lab-cast alloys with little primary intermetallic, and which met or exceeded structural casting properties requirements for yield strength and ductility. An accelerated demonstration of an HPDC automotive part was conducted in collaboration with two U.S. small businesses. Ingots made from 100% recycled 5xxx and 6xxx series scrap (plus Fe) were used to die cast one variant of this new family of Al-Mg-Si-Fe-Mn alloys (with high Si + Fe content) into a mid-sized HPDC structural-type automotive component. The HPDC alloy demonstration part showed good properties (especially ductility) and good castability for a complex component.

Plotkowski, Alex [ORNL] (ORCID:0000000154718681)↗

Enhanced Tensile and Tear Toughness Properties of Thin-Wall Vacuum-Assisted High-Pressure Die-Cast Aural-5 Alloy by Friction Stir Processing

Steadily rising demand for glider weight reduction has driven the development of vacuum-assisted high-pressure die-cast (HPDC) Al-alloys for automotive structural components. Aural-5 is a strontium-modified HPDC alloy utilizing manganese (Mn) to reduce die soldering, eliminating detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. HPDC Aural-5 contains shrinkage porosity, dendrites with Al-Si eutectic colonies, externally solidified crystals (ESCs), shear-band structure, and large second-phase particulates. Porosity, ESCs and large second-phase particles work as crack initiation sites, negatively impacting tensile properties. In this study, friction stir processing (FSP) is employed for microstructural modification of a thin-walled HPDC Aural-5 by eliminating porosity and breaking down dendrites, second-phase particles, eutectic colonies, ESCs and shear-band structures to create wrought microstructure with homogenized particle distribution. Mechanical property characterization indicates ~30% and ~35% enhancement in yield strength and ductility and associated marked effects on ~69% improvement in tear toughness according to the ASTM B871 test.

Friction stir processing, Aural-5, Strength, Tear ↗

Energy modeling and efficiency analysis of aluminum die-casting processes

Energy modeling and efficiency analysis are considered the foundation of manufacturing process optimization to improve quality and efficiency and reduce energy consumption and carbon emissions during aluminum die-casting processes. Our report introduced an energy modeling method to connect gas and electric energy consumption with production rate of aluminum die-casting processes based on data collected at workshops with various combination of machines and products. The detailed modeling process involved the development of a data-acquiring system and the comparison of various kinds of nonlinear regression methods. The resulting models were confirmed with actual production data and were also used to improve production scheduling. Furthermore, it was found that if the modeling results are reasonably used and production is accordingly well-scheduled, 10 to 15% of energy savings could be realized without sacrificing profits.

42 ENGINEERING↗

Catalyst layer formulations for slot-die coating of PEM fuel cell electrodes

The series of electrodes were fabricated by the scalable and manufacturable slot-die coating method for proton exchange membrane fuel cell (PEMFC) application. The inks with different amounts of solids were studied by rheological methods in order to establish a coating window with minimum manufacturing defects. The obtained electrodes were characterized by SEM, AFM, and optical microscopy, which showed that they were uniform and homogeneous with minimum defects. The electrochemical evaluation of the manufactured gas diffusion electrodes (GDE) showed that the main characteristics of the electrodes, like electrochemical surface area, proton resistivity, and double layer capacitance, were found to be close for all samples confirming the reproducibility of the slot-die process. Additionally, we studied the effects of membrane thickness on the performance of the GDE membrane electrode assemblies and determined that a decrease in membrane thickness favored the performance. Furthermore, the obtained results clearly demonstrated the applicability and feasibility of the approach for the Manufacturing of catalyst layers for the fuel cell application with potential for future mass production.

08 HYDROGEN↗

Characterization by X-ray tomography of granulated alumina powder during in situ die compaction

Compaction process, the aim of which being to obtain green bodies with low porosity and small size, is often used before sintering treatment. Prior to die filling, the ceramic powder is generally granulated to improve flowability. However during compaction, density heterogeneity and critical size defects may appear due to intergranule and granule-die wall frictions. In this work, the influence of granule formulation on the compact morphology has been studied. To do so, a compaction setup was installed inside an X-ray tomography equipment so that the evolution of the compact morphology could be analysed during the whole compaction process. We have demonstrated that high humidity rate and the addition of binder in the granule formulation increase density heterogeneity and generate larger defects. - Highlights: • An original compaction set up was installed inside an X-Ray tomography equipment. • The compaction process of granulated ceramic powder is imaged. • The compact green microstructure is quantified and related to the compaction stages. • The most detrimental defects of dry-pressed parts are caused by hollow granules. • Formulations without binder allow a reduction of the number of large defects.

36 MATERIALS SCIENCE↗

Effect of tool design and pass strategy on defect elimination and uniform, enhanced tensile properties of friction stir processed high-pressure die-cast A380 alloy

This work reports implementation of friction stir processing (FSP) to locally modify microstructure and create a defect-free processing zone with the aid of different tool designs and altering the passing strategy for two different process parameter combinations. Here, FSP is applied on high pressure die-cast (HPDC) A380 alloy, a widely used Al-Si alloy fabricated in the die casting sector for automotive and aerospace applications. However, the presence of gas and shrinkage porosity, brittle needle-shaped Fe-containing ß-FeSiAl 5 intermetallic compounds, Al-dendrites, coarse and acicular silicon particles, and large second-phase particulates have a detrimental influence on the uniformity of tensile properties across the thickness direction of an HPDC plate. FSP is able to eliminate porosity, refine microstructure and improve tensile properties. An FSP tool design and a passing strategy are identified for the best microstructure consolidation and uniform enhanced tensile properties. This study noted the importance of tool features such as scroll design and flats on tool pin and multiple pass orientation strategy to find best combination of defect-free refined microstructure and uniform tensile strength and ductility across the processing zone of HPDC Al alloys.

36 MATERIALS SCIENCE↗

Sub-critical assembly die-away analysis with organic scintillators

Determining the reactivity of systems containing fissile material is essential for verifying safety, and possession and enrichment levels. The goal of this experiment was to characterize a subcritical nuclear fuel assembly irradiated by a pulsed neutron generator through differential die-away analysis. Similar characterizations are commonly performed with thermal neutron detectors, but these detectors are bulky and cumbersome, the materials are not widely available, and timing can be clouded by the required thermalization time. In this work, an organic scintillator capable of detecting both neutrons and photons was used to measure the die-away profiles of both particles. These time profiles were then used to estimate the reactivity of the assembly. Here, the calculated reactivity estimates compare favorably to simulated estimates, and therefore provide a useful tool for fissile material characterization.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Simulation of 7050 Wrought Aluminum Alloy Wheel Die Forging and its Defects Analysis based on DEFORM

Defects such as folding, intercrystalline cracking and flow lines outcrop are very likely to occur in the forging of aluminum alloy. Moreover, it is difficult to achieve the optimal set of process parameters just by trial and error within an industrial environment. In producing 7050 wrought aluminum alloy wheel, a rigid-plastic finite element method (FEM) analysis has been performed to optimize die forging process. Processing parameters were analyzed, focusing on the effects of punch speed, friction factor and temperature. Meanwhile, mechanism as well as the evolution with respect to the defects of the wrought wheel was studied in details. From an analysis of the results, isothermal die forging was proposed for producing 7050 aluminum alloy wheel with good mechanical properties. Finally, verification experiment was carried out on hydropress.

36 MATERIALS SCIENCE↗

Experimental and Numerical Studies on the Formability of Materials in Hot Stamping and Cold Die Quenching Processes

Formability of steel and aluminium alloys in hot stamping and cold die quenching processes is studied in this research. Viscoplastic-damage constitutive equations are developed and determined from experimental data for the prediction of viscoplastic flow and ductility of the materials. The determined unified constitutive equations are then implemented into the commercial Finite Element code Abaqus/Explicit via a user defined subroutine, VUMAT. An FE process simulation model and numerical procedures are established for the modeling of hot stamping processes for a spherical part with a central hole. Different failure modes (failure takes place either near the central hole or in the mid span of the part) are obtained. To validate the simulation results, a test programme is developed, a test die set has been designed and manufactured, and tests have been carried out for the materials with different forming rates. It has been found that very close agreements between experimental and numerical process simulation results are obtained for the ranges of temperatures and forming rates carried out.

36 MATERIALS SCIENCE↗

Reliable four-point flexion test and model for die-to-wafer direct bonding

For many years, wafer-to-wafer (W2W) direct bonding has been very developed particularly in terms of bonding energy measurement and bonding mechanism comprehension. Nowadays, die-to-wafer (D2W) direct bonding has gained significant attention, for instance, in photonics and microelectro-mechanics, which supposes controlled and reliable fabrication processes. So, whatever the stuck materials may be, it is not obvious whether bonded D2W structures have the same bonding strength as bonded W2W ones, because of possible edge effects of dies. For that reason, it has been strongly required to develop a bonding energy measurement technique which is suitable for D2W structures. In this paper, both D2W- and W2W-type standard SiO{sub 2}-to-SiO{sub 2} direct bonding samples are fabricated from the same full-wafer bonding. Modifications of the four-point flexion test (4PT) technique and applications for measuring D2W direct bonding energies are reported. Thus, the comparison between the modified 4PT and the double-cantilever beam techniques is drawn, also considering possible impacts of the conditions of measures such as the water stress corrosion at the debonding interface and the friction error at the loading contact points. Finally, reliability of a modified technique and a new model established for measuring D2W direct bonding energies is demonstrated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Uncertainty Quantification of a Light Water Pulsed-Neutron Die-Away Experiment to Thermal Neutron Scattering Laws

Thermal neutron scattering laws are important nuclear data for many nuclear science and engineering applications. Validation helps to ensure that a thermal neutron scattering law has a high quality and often employs critical benchmarks as integral experiments. Recently, pulsed-neutron die-away benchmarks have been used as an experiment to validate thermal neutron scattering laws. Herein, we evidence how this alternative integral experiment has a high sensitivity to these nuclear data by performing an uncertainty quantification analysis. The analysis randomly sampled the nuclear model parameters associated with hydrogen bound in light water thermal neutron scattering law and sampled other nuclear data that influenced the experiment’s integral parameter (e.g., elastic scattering, absorption in hydrogen and oxygen) from their respective covariance matrices. The thermal neutron scattering law caused an uncertainty in the integral parameter that reached 2.67%, which exceeds by an order of magnitude the uncertainties induced in commonly used thermal solution critical benchmarks. The validation performed here, although limited due to a poor description of the historical experiment, indicated that the ENDF/B-VIII.0 thermal neutron scattering law well predicted the integral parameter. These results motivate further benchmark and validation efforts using pulsed-neutron die-away experiments.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Differential die-away instrument: Report on comparison of fuel assembly experiments and simulations

Experimental results of the assay of mock-up (fresh) fuel with the differential die-away (DDA) instrument were compared to the Monte Carlo N-Particle eXtended (MCNPX) simulation results. Most principal experimental observables, the die-away time and the in tegral of the DDA signal in several time domains, have been found in good agreement with the MCNPX simulation results. The remaining discrepancies between the simulation and experimental results are likely due to small differences between the actual experimental setup and the simulated geometry, including uncertainty in the DT neutron generator yield. Within this report we also present a sensitivity study of the DDA instrument which is a complex and sensitive system and demonstrate to what degree it can be impacted by geometry, material composition, and electronics performance.

07 ISOTOPE AND RADIATION SOURCES↗

Development of Functionally Graded Materials for Manufacturing Tools and Dies and Industrial Processing Equipment

Hot forming processes such as forging, die casting and glass forming require tooling that is subjected to high temperatures during the manufacturing of components. Current tooling is adversely affected by prolonged exposure at high temperatures. Initial studies were conducted to determine the root cause of tool failures in a number of applications. Results show that tool failures vary and depend on the operating environment under which they are used. Major root cause failures include (1) thermal softening, (2) fatigue and (3) tool erosion, all of which are affected by process boundary conditions such as lubrication, cooling, process speed, etc. While thermal management is a key to addressing tooling failures, it was clear that new tooling materials with superior high temperature strength could provide improved manufacturing efficiencies. These efficiencies are based on the use of functionally graded materials (FGM), a new subset of hybrid tools with customizable properties that can be fabricated using advanced powder metallurgy manufacturing technologies. Modeling studies of the various hot forming processes helped identify the effect of key variables such as stress, temperature and cooling rate and aid in the selection of tooling materials for specific applications. To address the problem of high temperature strength, several advanced powder metallurgy nickel and cobalt based alloys were selected for evaluation. These materials were manufactured into tooling using two relatively new consolidation processes. One process involved laser powder deposition (LPD) and the second involved a solid state dynamic powder consolidation (SSDPC) process. These processes made possible functionally graded materials (FGM) that resulted in shaped tooling that was monolithic, bi-metallic or substrate coated. Manufacturing of tooling with these processes was determined to be robust and consistent for a variety of materials. Prototype and production testing of FGM tooling showed the benefits of the nickel and cobalt based powder metallurgy alloys in a number of applications evaluated. Improvements in tool life ranged from three (3) to twenty (20) or more times than currently used tooling. Improvements were most dramatic where tool softening and deformation were the major cause of tool failures in hot/warm forging applications. Significant improvement was also noted in erosion of aluminum die casting tooling. Cost and energy savings can be realized as a result of increased tooling life, increased productivity and a reduction in scrap because of improved dimensional controls. Although LPD and SSDPC tooling usually have higher acquisition costs, net tooling costs per component produced drops dramatically with superior tool performance. Less energy is used to manufacture the tooling because fewer tools are required and less recycling of used tools are needed for the hot forming process. Energy is saved during the component manufacturing cycle because more parts can be produced in shorter periods of time. Energy is also saved by minimizing heating furnace idling time because of less downtime for tooling changes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Expanding the Range of Dies for Billet Production

Research shows that precise short billet whose length is less than its diameter may be produced from bar in a die with axial and radial differentiated compression. New designs are proposed for a cutting die and a system for radial bar clamping.

42 ENGINEERING↗

New Pulsed Neutron Die-Away Experiments in Light Water

Thermal neutron scattering laws are important data for many nuclear science and engineering applications, especially criticality safety. Recently, pulsed-neutron die-away experiments have been proposed and used as an experiment to validate thermal neutron scattering laws. These experiments involve irradiating a target moderating material with pulses of neutrons from a neutron generator. The physics of thermal scattering greatly affect how the neutron population in the target exponentially decays via absorption and leakage. Herein, we present experimental results from a new pulsed-neutron die-away experiment of light water that was performed at Lawrence Livermore National Laboratory. The experiments were done with cylindrical targets of varying dimensions to modulate the experiment’s sensitivity to thermal scattering and to absorption. We compare the measured integral parameter of the experiment to simulations with MCNP6.2 ® and to past experiments in literature. The integral parameters that were more sensitive to TSLs showed a larger bias. This validation study is known to have errors because the model of the experiment lacks key features about the detectors and neutron generator. These features will be included in the final benchmark evaluation of the experiment which will be submitted to the International Criticality Safety Benchmark Evaluation Project.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

IER 501: Pulsed Neutron Die-Away Experiments at LLNL [Slides]

This presentation notes the purpose of Pulsed Neutron Die Away (PNDA) for Thermal Neutron Scattering Law (TSL) validation. PNDA for TSL validation does not require fissile material. It consists of simple target shapes and compositions and is only sensitive to absorption and scattering of target medium. Well conducted experiments have uncertainties of 0.1% - 0.5%. This presentation also covers Pulsed Neutron Die Away Experiments, while noting previous experiments such as the FY22 PNDA Experiments. The presentation concludes with FY23 benchmarking efforts and a timeline to FY24.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Die Molybdän(V)‐ und Wolfram(VI)‐oxoazide [MoO(N 3 ) 3 ], [MoO(N 3 ) 3 ⋅2 CH 3 CN], [(bipy)MoO(N 3 ) 3 ], [MoO(N 3 ) 5 ] 2− , [WO(N 3 ) 4 ] und [WO(N 3 ) 4 ⋅CH 3 CN]

Abstract Eine Serie neuartiger Molybdän(V)‐ und Wolfram(VI)‐oxoazide wurde ausgehend von [MOF 4 ] (M=Mo, W) und Me 3 SiN 3 synthetisiert. Während [WO(N 3 ) 4 ] durch Fluorid‐Azid‐Austausch in der Umsetzung von Me 3 SiN 3 mit [WOF 4 ] in SO 2 ‐Lösung erhalten wurde, resultierte die Reaktion mit MoOF 4 in einer Reduktion von Mo VI zu Mo V unter Bildung von [MoO(N 3 ) 3 ]. Entsprechende Umsetzungen in Acetonitrillösung führten zur Isolierung der Addukte [MoO(N 3 ) 3 ⋅2 CH 3 CN] und [WO(N 3 ) 4 ⋅CH 3 CN]. [(bipy)MoO(N 3 ) 3 ] und [PPh 4 ] 2 [MoO(N 3 ) 5 ] konnten nach anschließenden Umsetzungen von [MoO(N 3 ) 3 ] mit 2,2′‐Bipyridin bzw. [PPh 4 ][N 3 ] isoliert werden. Die Molybdän(V)‐ und Wolfram(VI)‐oxoazide wurden schwingungsspektroskopisch, bezüglich ihrer Empfindlichkeit gegenüber Schlag, Reibung und Erhitzen, und im Fall von [WO(N 3 ) 4 ⋅CH 3 CN], [(bipy)MoO(N 3 ) 3 ] und [PPh 4 ] 2 [MoO(N 3 ) 5 ] auch durch Kristallstrukturanalysen charakterisiert.

Haiges, Ralf↗

Microstructural modification of a high-pressure die-cast A380 alloy through friction stir processing and its effect on mechanical properties

Aluminum alloy A380 is one of the major high-pressure die-cast (HPDC) alloys fabricated in the die casting sector. However, microstructural features such as shrinkage and gas porosity, entrapped oxide inclusions, change in the morphology of eutectic Si particles as a function of casting location, and the presence of multiple second phase particulates, especially Fe-bearing phases in HPDC A380 alloy results in limited ductility, thus, affecting its structural application. However, through proper modification of the as-cast microstructure, it is possible to improve the mechanical performance of alloy A380. In this study, we report the effect of friction stir processing (FSP), a well-known severe plastic deformation (SPD) and thermomechanical processing tool for selective microstructural modification, on A380. FSP effectively refines the as-cast microstructure and breaks down the coarse Si particles, creating a homogenized distribution of equiaxed Si particles in the aluminum matrix. Additionally, FSP eliminates porosity that acts as crack initiation sites, leading to improved mechanical strength and ductility.

Friction stir processing, Aluminum alloys, Mechani↗