Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DART”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Core/Combustor-Noise Baseline Measurements for the DGEN Aeropropulsion Research Turbofan

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and advances in mitigation of other noise sources. Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratio from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-eduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. The new NASA DGEN Aeropropulsion Research Turbofan (DART) is a cost-efficient testbed for the study of core-noise physics and mitigation. This paper describes the recently completed DART core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). Acoustic data was simultaneously acquired using the AAPL overhead microphone array in the engine aft quadrant far field, a single midfield microphone, and two semi-infinite-tube unsteady pressure sensors at the core-nozzle exit. Combustor-noise components of measured total-noise signatures were educed using a two-signal source-separation method and are found to occur in the expected frequency range. The acoustic data compares well with results from a limited 2014 feasibility test and will serve as a high-quality baseline for future research using the DART. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

Aeroacoustics↗
NASA NTRS2019

Acoustic Directivity and Insertion Loss Measurements of Advanced Liners Installed the Inlet of the DGEN Aeropropulsion Research Turbofan

The NASA Glenn Research Center’s DGEN Aeropropulsion Research Turbofan (DART) is based on the Price Induction DGEN380—a small, ~500-lbf thrust class, high-bypass, geared-turbofan engine with a separate flow nozzle. The general characteristics of the DART make it an ideal candidate for utilization as a test bed for engine aeroacoustic research in a relevant performance environment. The DART was used to document the efficacy of acoustic liners installed in the inlet of the DGEN380. An advanced multi-degree-of-freedom liner (MDOF) was designed and tested, along with a traditional single-degree-of- freedom liner (SDOF), and those results compared to a hard-wall baseline inlet. Farfield acoustic data were acquired from an external array, evaluated, and reported here-in terms of overall, broadband, and tonal components of the insertion loss.

Noise Reduction↗
NASA NTRS2019

NEXT Ion Propulsion System Risk Mitigation Tests in Support of the Double Asteroid Redirection Test Mission

Risk mitigation tests have been conducted by the NASA Glenn Research Center and The Aerospace Corporation in support of the DART Mission. The tests focused on NEXT performance characterizations intended to ensure its operations and characteristics are compatible with the DART mission operations, and to assist in the definition of the propulsion system. Tests were performed at the Aerospace Corporation and they involved: flow sensitivity-analyses, steady-state performance characterizations, and measurements of thruster erosion. The tests also involved defining, demonstrating, verifying, and evaluating the start-up sequences and a beam current regulation algorithm consistent with DART mission requirements. It was found that NEXT thruster operations are compatible with the proposed relaxation of flow control ranges for ignition and for steady-state operation.

Thomas, Robert E.↗
NASA NTRS2019

NEXT Ion Propulsion System Risk Mitigation Tests in Support of the Double Asteroid Redirection Test Mission

Risk mitigation tests have been conducted by the NASA Glenn Research Center and The Aerospace Corporation in support of the DART Mission. The tests focused on NEXT performance characterizations intended to ensure its operations and characteristics are compatible with the DART mission operations, and to assist in the definition of the propulsion system. Tests were performed at the Aerospace Corporation and they involved: flow sensitivity-analyses, steady-state performance characterizations, and measurements of thruster erosion. The tests also involved defining, demonstrating, verifying, and evaluating the start-up sequences and a beam current regulation algorithm consistent with DART mission requirements. It was found that NEXT thruster operations are compatible with the proposed relaxation of flow control ranges for ignition and for steady-state operation.

Thomas, Robert E.↗
NASA NTRS2019

NEXT Ion Propulsion System Risk Mitigation Tests in Support of the Double Asteroid Redirection Test Mission

Risk mitigation tests have been conducted by the NASA Glenn Research Center and The Aerospace Corporation in support of the DART Mission. The tests focused on NEXT performance characterizations intended to ensure its operations and characteristics are compatible with the DART mission operations, and to assist in the definition of the propulsion system. Tests were performed at the Aerospace Corporation and they involved: flow sensitivity-analyses, steady-state performance characterizations, and measurements of thruster erosion. The tests also involved defining, demonstrating, verifying, and evaluating the start-up sequences and a beam current regulation algorithm consistent with DART mission requirements. It was found that NEXT thruster operations are compatible with the proposed relaxation of flow control ranges for ignition and for steady-state operation.

Thomas, Robert E.↗
NASA NTRS2020

A Jupyter Notebook Environment For Multibody Dynamics

DARTS is a rigid/flexible multibody dynamics toolkit for themodeling and simulation of aerospace and robotic vehicles forengineering applications. In this paper we describe an on-line,browser-based environment using Jupyter notebooks to supporttraining needs for the DARTS software. The suite of curated tutorial notebooks is organized into different topic areas, and intomultiple themes within each topic area. The notebooks within atheme use a progression of examples for users to expand theirunderstanding of the software. The topic areas include one onthe DARTS multibody dynamics software and another one on thetheory underlying the multibody dynamics formulation. We alsodescribe a number of Jupyter extensions that were used - andsome developed in house - to enhance the notebook interface foruse with the dynamics simulation software. One significant extension we implemented allows the embedding of live 3D visualizations within simulation notebooks.

Gaut, Aaron↗
NASA NTRSDate not supplied

NASA Systems Engineering and Safety Culture: Aerospace Project Design and Implementation Challenges

Using Systems Engineering principles and the NASA Glenn Safety procedures and protocols, a rigorous method was developed to ensure safe testing and operation of a small, commercial off the shelf turbofan engine at the Aero-Acoustic Propulsion Laboratory (AAPL). The DGEN380 is a small, ~500-lbf thrust class, high-bypass, geared- turbofan engine with a separate flow nozzle. It is a modular, compact, lightweight turbofan with Full-Authority Digital Engine Control. It’s general characteristics make it an ideal candidate for utilization as a testbed for engine aero-acoustic technology maturation in a relevant performance environment. The DGEN380 is the core component of the DGEN Aero-propulsion Research Turbofan (DART) mobile test rig. The full presentation will describe the risk assessment and mitigation process applied to the DART by the project team. The identification and analysis of failure modes led to the development of risk mitigation plans, which include administrative, engineering, and physical controls for the safe operation of the DART test rig at the AAPL facility.

Systems Engineering, Aeronautics, safety↗
NASA NTRS1972

Responses of blind fish to gravitational changes as achieved in parabolic flight

Blind fish, during parabolic flight, display a measurable and consistent behavior. The most spectacular new behavioral response is the forward looping of blind fish in or near weightlessness. This response shows no measurable adaptation during the entire period of weightlessness of about 30 sec. During the entrance and exit of weightless parabolas (pushover and pullout) respectively, the fish assumes a forward tilted diving position. Parabolic flight with negative g in the range between 0g and -1g causes similar diving responses of the fish with the only difference being that the dive is directed toward the top of the fish tank. When the response to a g value less than 1g is compared to the response to increased g load on the ground (escape of darting response) an essential difference is seen: higher horizontal acceleration or jerk on the ground causes fish to swim, or even dart, against the direction of inertial force; fish during weightless parabolas move into the direction of the inertial or gravitational force. Since the vestibular system of fish is homologous to that of man, the observed behavior of fish in weightless flight could help to better understand human performance and sensations in comparable situations.

Vonbaumgarten, R. J.↗
NASA NTRS1988

Application of a Comprehensive Analytical Model of Rotor Aerodynamics and Dynamics (CAMRAD) to the McDonnell Douglas AH-64A helicopter

A model of the AH-64A helicopter was generated in a Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics (CAMRAD) in an effort to validate its analytical capabilities for modeling a current advanced Army helicopter. The initial phase of the effort involved the generation of CAMRAD input files necessary for the complete aerodynamic, structural, and dynamic definition of the production AH-64A helicopter. The input files were checked by making comparisons of CAMRAD full helicopter trim and main rotor blade natural frequency predictions with those of full helicopter trim program, Blade Element Trim (BETRIM), and dynamic analysis code, Dynamic Analysis Research Tool (DART), respectively. The main thrust concerned the application of the AH-64A CAMRAD model thus developed and verified for main rotor blade structural loads predictions and comparison with DART analytical results. The investigation provided insight not only into the usefulness of CAMRAD for the AH-64A performance and dynamics prediction, but also into the limitations of the program for modeling advanced rotor and fuselage systems. The model development effort is discussed, the results of the CAMRAD correlation studies presented, and some general conclusions are offered on the applicability of CAMRAD for rotor aeroelastic loads prediction for current and future rotorcraft configurations.

Callahan, Cynthia B.↗
NASA NTRS1990

Multistroke cloud-to-ground strike to the NASA F-106B airplane

An analysis of electromagnetic waveform records and video images of a multistroke cloud-to-ground (CG) strike to the NASA F-106B instrumented airplane is presented. The CG flash started as a lightning strike triggered by the airplane and later produced multiple return strokes to the ground (the ground strike network registered six return strokes). Although there are some uncertainties in data interpretation resulting from lack of independent measurements with other than the airborne instruments, recoil streamers and eight sequences of dart leaders followed by return strokes (two more than were indicated by the ground network) were identified in the airborne data. At least three of the subsequent return strokes were attached to the airplane. The analysis provides evidence that formation of recoil streamers and dart leaders is accompanied by a surge in continuous current. This feature is similar to that observed in the bidirectional leader development during lightning initiation on the airplane.

Mazur, Vladislav↗
NASA NTRS1991

Power and energy dissipation in subsequent return strokes as predicted by a new return stroke model

Recently, Cooray introduced a new return stroke model which is capable of predicting the temporal behavior of the return stroke current and the return stroke velocity as a function of the height along the return stroke channel. The authors employed this model to calculate the power and energy dissipation in subsequent return strokes. The results of these calculations are presented here. It was concluded that a large fraction of the total energy available for the dart leader-subsequent stroke process is dissipated in the dart leader stage. The peak power per unit length dissipated in a subsequent stroke channel element decreases with increasing height of that channel element from ground level. For a given channel element, the peak power dissipation increases with increasing current in that channel element. The peak electrical power dissipation in a typical subsequent return stroke is about 1.5 times 10(exp 11) W. The energy dissipation in a subsequent stroke increases with increasing current in the return stroke channel, and for a typical subsequent stroke, the energy dissipation per unit length is about 5.0 times 10(exp 3) J/m.

Cooray, Vernon↗
NASA NTRS1994

Sampling Particles In Hot Gas Plumes

Sampling darts and launching apparatus built to collect particles in vertical plume of hot gas. In original application, hot gas plume is rocket-engine exhaust during test firing. Dart passes made at various heights, depending on launch angle and launch-gas pressure. Adaptable to variety of terrestrial uses like research on particulate emissions of volcanoes or determining origin of building fire while still burning.

Taylor, James F.↗
NASA NTRS1995

Plume particle collection and sizing from static firing of solid rocket motors

A unique dart system has been designed and built at the NASA Marshall Space Flight Center to collect aluminum oxide plume particles from the plumes of large scale solid rocket motors, such as the space shuttle RSRM. The capability of this system to collect clean samples from both the vertically fired MNASA (18.3% scaled version of the RSRM) motors and the horizontally fired RSRM motor has been demonstrated. The particle mass averaged diameters, d43, measured from the samples for the different motors, ranged from 8 to 11 mu m and were independent of the dart collection surface and the motor burn time. The measured results agreed well with those calculated using the industry standard Hermsen's correlation within the standard deviation of the correlation . For each of the samples analyzed from both MNASA and RSRM motors, the distribution of the cumulative mass fraction of the plume oxide particles as a function of the particle diameter was best described by a monomodal log-normal distribution with a standard deviation of 0.13 - 0.15. This distribution agreed well with the theoretical prediction by Salita using the OD3P code for the RSRM motor at the nozzle exit plane.

Sambamurthi, Jay K.↗
NASA NTRS1999

Status of the Dust Accumulation and Removal Technology Experiment for the Mars 2001 Surveyor Lander

The Dust Accumulation and Removal Technology (DART) experiment is designed to quantify the nature of dust settling out of the Martian atmosphere. DART is part of the Mars in-situ propellant precursor (MIP) experiment which is a payload on the Mars 2001 Surveyor Lander. At the time of this writing, high fidelity development hardware has been integrated in to the MIP experiment and completed Mars environment testing. Additional information is contained in the original extended abstract.

Jenkins, P. P.↗
NASA NTRS2001

A Dust Characterization Experiment for Solar Cells Operating on Mars

During the Viking and Pathfinder missions to Mars, significant amounts of dust accumulated on the spacecrafts. In Pathfinder's case, the dust obscured the solar panels on the lander and the rover degrading their output current. The material adherence experiment aboard the Pathfinder rover quantified the rate of decrease in short circuit current at 0.28% per day. This rate is unacceptably high for long duration missions. In response, NASA has developed the Dust Accumulation and Removal Technology (DART) experiment. DART has three instruments for characterizing dust settling out of the atmosphere and tests two methods to keep dust from settling on solar cells.

Jenkins, Phillip↗
NASA NTRS2004

Advanced Video Guidance Sensor (AVGS) Development Testing

NASA's Marshall Space Flight Center was the driving force behind the development of the Advanced Video Guidance Sensor, an active sensor system that provides near-range sensor data as part of an automatic rendezvous and docking system. The sensor determines the relative positions and attitudes between the active sensor and the passive target at ranges up to 300 meters. The AVGS uses laser diodes to illuminate retro-reflectors in the target, a solid-state camera to detect the return from the target, and image capture electronics and a digital signal processor to convert the video information into the relative positions and attitudes. The AVGS will fly as part of the Demonstration of Autonomous Rendezvous Technologies (DART) in October, 2004. This development effort has required a great deal of testing of various sorts at every phase of development. Some of the test efforts included optical characterization of performance with the intended target, thermal vacuum testing, performance tests in long range vacuum facilities, EMI/EMC tests, and performance testing in dynamic situations. The sensor has been shown to track a target at ranges of up to 300 meters, both in vacuum and ambient conditions, to survive and operate during the thermal vacuum cycling specific to the DART mission, to handle EM1 well, and to perform well in dynamic situations.

Howard, Richard T.↗
NASA NTRS2004

Advanced Video Guidance Sensor and Next Generation Autonomous Docking Sensors

In recent decades, NASA's interest in spacecraft rendezvous and proximity operations has grown. Additional instrumentation is needed to improve manned docking operations' safety, as well as to enable telerobotic operation of spacecraft or completely autonomous rendezvous and docking. To address this need, Advanced Optical Systems, Inc., Orbital Sciences Corporation, and Marshall Space Flight Center have developed the Advanced Video Guidance Sensor (AVGS) under the auspices of the Demonstration of Autonomous Rendezvous Technology (DART) program. Given a cooperative target comprising several retro-reflectors, AVGS provides six-degree-of-freedom information at ranges of up to 300 meters for the DART target. It does so by imaging the target, then performing pattern recognition on the resulting image. Longer range operation is possible through different target geometries. Now that AVGS is being readied for its test flight in 2004, the question is: what next? Modifications can be made to AVGS, including different pattern recognition algorithms and changes to the retro-reflector targets, to make it more robust and accurate. AVGS could be coupled with other space-qualified sensors, such as a laser range-and-bearing finder, that would operate at longer ranges. Different target configurations, including the use of active targets, could result in significant miniaturization over the current AVGS package. We will discuss these and other possibilities for a next-generation docking sensor or sensor suite that involve AVGS.

Granade, Stephen R.↗
NASA NTRS2006

Performance Evaluation of a UWB-RFID System for Potential Space Applications

This talk presents a brief overview of the ultra-wideband (UWB) RFID system with emphasis on the performance evaluation of a commercially available UWB-RFID system. There are many RFID systems available today, but many provide just basic identification for auditing and inventory tracking. For applications that require high precision real time tracking, UWB technology has been shown to be a viable solution. The use of extremely short bursts of RF pulses offers high immunity to interference from other RF systems, precise tracking due to sub-nanosecond time resolution, and robust performance in multipath environments. The UWB-RFID system Sapphire DART (Digital Active RFID & Tracking) will be introduced in this talk. Laboratory testing using Sapphire DART is performed to evaluate its capability such as coverage area, accuracy, ease of operation, and robustness. Performance evaluation of this system in an operational environment (a receiving warehouse) for inventory tracking is also conducted. Concepts of using the UWB-RFID technology to track astronauts and assets are being proposed for space exploration.

Phan, Chan T.↗