SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Outputs of two magnetrons added coherently in scheme based on resonant waveguide coupling and injection phase locking. In addition, filaments are turned off after starting. Overall effect is relatively-inexpensive, lowpower, noisy magnetrons generate clean carrier signals of higher power that ordinarily require more expensive klystrons.
A conventional low-noise detector requires a technique to both absorb incident power and convert it to an electrical signal at cryogenic temperatures. This innovation combines low-noise detector and readout functionality into one device while maintaining high absorption, controlled polarization sensitivity, and broadband detection capability. The resulting far-infrared detectors can be read out with a simple approach, which is compact and minimizes thermal loading. The proposed microwave kinetic inductance detector (MKID) consists of three basic elements. The first is the absorptive section in which the incident power is coupled to a superconducting resonator at far-infrared frequency above its superconducting critical frequency (where superconductor becomes normal conductor). This absorber's shape effectively absorbs signals in the desired polarization state and is resonant at the radio frequency (RF) used for readout of the device. Control over the metal film used in the absorber allows realization of structures with either a 50% broadband or 100% resonance absorptance over a 30% fractional bandwidth. The second element is a microwave resonator - which is realized from the thin metal films used to make the absorber as transmission lines - whose resonance frequency changes due to a variation in its kinetic inductance. The resonator's kinetic inductance is a function of the power absorbed by the device. A low-loss dielectric (mono-crystalline silicon) is used in a parallel-plate transmission line structure to realize the desired superconducting resonators. There is negligible coupling among the adjacent elements used to define the polarization sensitivity of each detector. The final component of the device is a microwave transmission line, which is coupled to the resonator, and allows detection of changes in resonance frequency for each detector in the focal plane array. The spiral shape of the detector's absorber allows incident power with two polarizations to couple to the detector equally. A stepped impedance resonator was used that allows the incident power absorbed in the detecting membrane area to be uniformly distributed in the detector's transmission line at the RF readout frequency. This maximizes the sensitivity of the detector. The signal is read out via a frequency multiplexing technique that requires a minimum number of interface transmission lines for readout. This reduces the packaging complexity and coupling to the device's thermal environment.
High temperature superconductors(HTS) and microwaves devices form the ideal partnership. The application of superconductors in microwave devices, components and systems allows the reduction in size, power consumption and insertion loss. The surface resistance of high-Tc superconductors has been found to be two orders of magnitude lower than normal conducting copper materials. The reduction in size and power requirements, which together both lead to a reduction in system mass, coupled with reasonably accessible operating temperatures, suggest that HTS microwave components should find ready application in satellite communications systems. At present, multi- channeling communication networks demand filters with narrow bandwidth in order to allow the available RF frequency spectrum to be partitioned into small frequency bands, -and possible variation of dielectric constant from substrate to substrate is undesirable. Microwave multiplexers demand the fabrication of two identical filters in each channel. Thus, the filter with tuning function is preferable. Tunable filters are the critical component for phased array antennas in order to electronically steer the radiated beam. To fabricate a tunable filter that uses an electric field for operation, one would like a material that provides a large change on dielectric constant for a given electric field, yet has a relatively low tangent in order to minimize the insertion loss of the device. Ferroelectrics have been the materials of choice. Their large dielectric constant sufficiently increases the coupling between microwave resonators and its dependence on electric field provides timability. Development of technology promises to diminish tangent loss. The use of thin ferroelectric films sufficiently decreases insertion losses keeping considerable potential for applications. NASA Lewis Research Center is the one of the leading centers in investigation of superconductors/ferroelectric tunable components for microwave devices. A large number of possible microwave devices were fabricated and tested on the basis of thin film multilayer superconductor-ferroelectric structures. In major cases the systems with edge-coupling scheme were investigated. Dr. Genkin has recently focused on the new potentialities which implements the using of thin ferroelectric films in filters fabricated with end-coupled microstrip lines. Numerical modeling shows that these systems have large potential for application in tunable narrow- and wide-bandpass filters in the frequency range 10-20 GHz. The phase shifter with end-coupled resonant sections was fabricated and tested. Experimental results show large tunability, particular in low voltages. The possible optimization of this structure promises to improve the obtained result and to reach the low level of insertion losses.
Optical combs generated by a monolithic resonator with Kerrmedium can be used in a number of applications, including orbital clocks and frequency standards of extremely high accuracy, such as astronomy, molecular spectroscopy, and the like. The main difficulty of this approach is the relatively high pump power that has to be used in such devices, causing undesired thermorefractive effects, as well as stimulated Raman scattering, and limiting the optical comb quality and utility. In order to overcome this problem, this innovation uses a different approach to excitation of the nonlinear oscillations in a Kerr-nonlinear whispering gallery mode (WGM) resonator and generation of the optical comb. By coupling to the resonator two optical pump frequencies instead of just one, the efficiency of the comb source can be increased considerably. It therefore can operate in a lowerpower regime where the undesirable effects are not present. This process does not have a power threshold; therefore, the new optical component can easily be made strong enough to generate further components, making the optical comb spread in a cascade fashion. Additionally, the comb spacing can be made in an arbitrary number of the resonator free spectral ranges (FSR). The experimental setup for this innovation used a fluorite resonator with OMEGA= 13.56 GHz. This material has very low dispersion at the wavelength of 1.5 microns, so the resonator spectrum around this wavelength is highly equidistant. Light was coupled in and out of the resonator using two optical fibers polished at the optimal coupling angle. The gap between the resonator and the fibers, affecting the light coupling and the resonator loading, was controlled by piezo positioners. The light from the input fiber that did not go into the resonator reflected off of its rim, and was collected by a photodetector. This enabled observation and measurement of the (absorption) spectrum of the resonator. The input fiber combined light from two lasers centered at around 1,560 nanometers. Both laser frequencies were simultaneously scanned around the selected WGMs of the same family. However, they were separated by one, two, three, or ten FSRs. This was achieved by fine-tuning each laser frequency offset until the selected resonances overlap on the oscilloscope screen. The resonator quality factor Q = 7 x 10(exp 7) was relatively low to increase the linewidth and, therefore, the duty cycle of both lasers simultaneously coupled into their WGMs. The optical spectrum analyzer (OSA) connected to the output fiber was continuously acquiring data, asynchronously with the laser scan. The instrument was set to retain the peak power values; therefore, a trace recorded for a sufficiently long period of time reflected the situation with both lasers maximally coupled to the WGMs.
A hemispherical open resonator has previously been used to make relative comparisons of the surface resistivity of metallic thin-film samples in the submillimeter wavelength region. This resonator is fed from a far-infrared laser via a small coupling hole in the center of the concave spherical mirror. The experimental arrangement, while desirable as a coupling geometry for monitoring weak emissions from the cavity, can lead to the introduction of spurious modes into the cavity. Sources of these modes are identified, and a simple alteration of the experimental apparatus to eliminate such modes is suggested.
Input and output coupling constants of spin-2 mesons with two pseudo-scalar mesons obtained by producing resonances at experimentally observed positions
For array of "brick" configuration there are electrical and mechanical advantages to feed the antenna with a feed on a substrate perpendicular to the antenna substrate. Different techniques have been proposed for exciting patch antennas using such a feed structure.Rncently, an aperture-coupled dielectric resonator antenna using a perpendicular feed substrate has been demonstrated to have very good power coupling efficiency. For a two-dimensional rectangular array with tapered slot antenna elements, a power combining network on perpendicular substrate is generally required to couple power to or from the array. In this paper, we will describe two aperture-coupled techniques for coupling microwave power from a linearly tapered slot antenna (LTSA) to a microstrip feed on a perpendicular substrate. In addition, we will present measured results for return losses and radiation patterns.
The performance of gold/SrTio3 /LaAlO3 conductor/ferroelectric/dielectric side-coupled, tunable ring resonators at K-band frequencies is presented. The tunability of these rings arises from the sensitivity of the relative dielectric constant (Er) of SrTiO 3 to changes in temperature and dc electric fields (E). We observed that the change in F-, which takes place by biasing the ring up to 450 V alters the effective dielectric constant (e-eff) of the circuit resulting in a 3k resonant frequency shift of nearly 12 % at 77 K. By applying a separate dc bias between the microstrip line and the ring, one can optimize their coupling to obtain bandstop resonators with unloaded quality factors (Q(sub o)) as high as 12,000. The 31 resonance was tuned from 15.75 to 17.41 GHz while keeping Q. above 768 over this range. The relevance of these results for practical microwave components will be discussed.
Relativistic electrons in the outer radiation belt are highly dynamic and respond to interplanetary solar wind structures interacting with the Earth's magnetic field. A known mechanism dictating electron dynamics is the drift-resonant interaction with ultralow frequency (ULF) waves. The present work simulates the ring current and radiation belt electron populations in the bounce-averaged, kinetic Comprehensive Inner Magnetosphere-Ionosphere model coupled with the Block Adaptive Tree Solar Wind Roe-type Upwind Scheme global magnetospheric magnetohydrodynamic (MHD) code using an idealized ULF wave solar wind density driver. ULF waves generated with 10 min periods (at 1.67 mHz frequencies) in the MHD model are characterized and the corresponding energization of electrons and radial transport of electron phase space density is presented. The drift-resonant electron energy is determined in the simulation and is consistent with the electron resonance conditions in dipolar magnetic fields. The present results will be an important component of understanding inner magnetospheric dynamics and how these inner magnetospheric populations interact with ULF waves resulting from interplanetary solar wind structures.
Coupling dynamics can produce either adverse or beneficial stability and controllability, depending on the characteristics of the aircraft. This report presents archival anecdotes and analyses of coupling problems experienced by the X-series, Century series, and Space Shuttle aircraft. The three catastrophic sequential coupling modes of the X-2 airplane and the two simultaneous unstable modes of the X-15 and Space Shuttle aircraft are discussed. In addition, the most complex of the coupling interactions, inertia roll coupling, is discussed for the X-2, X-3, F-100A, and YF-102 aircraft. The mechanics of gyroscopics, centrifugal effect, and resonance in coupling dynamics are described. The coupling modes discussed are interacting multiple degrees of freedom of inertial and aerodynamic forces and moments. The aircraft are assumed to be rigid bodies. Structural couplings are not addressed. Various solutions for coupling instabilities are discussed.
We present design progress and subsystem test results for a new short-term frequency standard, the Voltage Controlled Sapphire Oscillator (VCSO). Included are sapphire resonator and coupling design, cryocooler environmental sensitivity tests, Q measurement results, and turnover temperature results. A previous report presented history of the design related to resonator frequency and frequency compensation [1]. Performance goals are a frequency stability of 1x10(exp -14) (1 second less than or equal to (tau) less than or equal to 100 seconds) and two years or more continuous operation. Long-term operation and small size are facilitated by use of a small Stirling cryo-cooler (160W wall power) with an expected 5 year life.
The interaction between the surface plasmon mode that propagates at a metal dielectric interface and the localized plasma resonances (LPR) is investigated experimentally in Ag-island films. A stair-stepped sample geometry comprising a glass substrate, a continuous 50-nm Ag film, an LiF spacer film of thickness d = 5-60 nm, and an Ag-island film of mass thickness 3 nm is used in near-normal-reflectivity and plasmon-propagation-constant (k) determinations. The results are presented graphically and discussed. The overall shape of the reflectivity curves is found to be characteristic of Ag films, but with a dip at about 400 nm (corresponding to the absorption resonance of the island film) which is most pronounced with d = 25 nm. It is inferred that the island resonances are strongly coupled to a continuous-film dissipative mechanism at this d value. This inference is supported by the fact that the variation in k, correctd for LiF effects and plotted as a function of d, is greatest at around d = 25 nm. The implications of this finding for broad-band coupling into a thin-film mode, LPR enhancement of waveguide nonlinear effects, and new surface-enhanced-Raman-scattering geometries are indicated.
The tiltrotor offers the best mix of hovering and cruise flight of any of the current V/STOL configurations. One possible improvement on the tiltrotors of today designs would be using a soft-inplane hingeless hub. The advantages to a soft-inplane hingeless hub range from reduced weight and maintenance to reduced vibration and loads. However, soft-inplane rotor systems are inherently in danger of the aeromechanical instabilities of ground and air resonance. Furthermore tiltrotors can be subject to whirl flutter. At least in part because of the potential for air and ground resonance in a soft-inplane rotor, the Bell XV-15, the Bell-Boeing V-22 Osprey, and the new Bell Augusta 609 have stiff-inplane, gimballed rotors which do not experience these instabilities. In order to design soft-inplane V/STOL aircraft that do not experience ground or air resonance, it is important to be able to predict these instabilities accurately. Much of the research studying the stability of tiltrotors has been focused on the understanding and prediction of whirl flutter. As this instability is increasingly well understood, air and ground resonance for a tiltrotor need to be investigated. Once we understand the problems of air and ground resonance in a tiltrotor, we must look for solutions to these instabilities. Other researchers have found composite or kinematic couplings in the blades of a helicopter helpful for ground and air resonance stability. Tiltrotor research has shown composite couplings in the wing to be helpful for whirl flutter. Therefore, this project will undertake to model ground and air resonance of a soft-inplane hingeless tiltrotor to understand the mechanisms involved and to evaluate whether aeroelastic couplings in the wing or kinematic couplings in the blades would aid in stabilizing these instabilities in a tiltrotor.
Surface waves on Earth's magnetopause have a controlling effect upon global magnetospheric dynamics. Since spacecraft provide sparse in situ observation points, remote sensing these modes using ground-based instruments in the polar regions is desirable. However, many open conceptual questions on the expected signatures remain. Therefore, we provide predictions of key qualitative features expected in auroral, ionospheric, and ground magnetic observations through both magnetohydrodynamic theory and a global coupled magnetosphere-ionosphere simulation of a magnetopause surface eigenmode. These show monochromatic oscillatory field-aligned currents (FACs), due to both the surface mode and its non-resonant Alfvén coupling, are present throughout the magnetosphere. The currents peak in amplitude at the equatorward edge of the magnetopause boundary layer, not the open-closed boundary as previously thought. They also exhibit slow poleward phase motion rather than being purely evanescent. We suggest the upward FAC perturbations may result in periodic auroral brightenings. In the ionosphere, convection vortices circulate the poleward moving FAC structures. Finally, surface mode signals are predicted in the ground magnetic field, with ionospheric Hall currents rotating perturbations by approximately (but not exactly) 90° compared to the magnetosphere. Thus typical dayside magnetopause surface modes should be strongest in the East-West ground magnetic field component. Overall, all ground-based signatures of the magnetopause surface mode are predicted to have the same frequency across L-shells, amplitudes that maximize near the magnetopause's equatorward edge, and larger latitudinal scales than for field line resonance. Implications in terms of ionospheric Joule heating and geomagnetically induced currents are discussed.
It is demonstrated how the design of graded-reflectance output coupler unstable laser cavities may be tailored to significantly enhance the overall power transmission efficiency of a given laser system relative to that of a conventional diffractively coupled unstable resonator. The importance of these findings in coherent lidar applications is explained with particular emphasis on projected space-based systems.
An electron beam microwave device having an evacuated interaction chamber to which are coupled a resonant cavity which has an opening between the resonant cavity and the evacuated interaction chamber and an electron gun which causes a narrow beam of electrons to traverse the evacuated interaction chamber. The device also contains a mechanism for feeding back a microwave electromagnetic field from the resonant cavity to the evacuated interaction chamber in such a way as to modulate the direction of propagation of the electron beam, thereby further amplifyjng the microwave electromagnetic field. Furthermore, provision is made for coupling the electromagnetic field out of the electron beam microwave device.
Recent large-scale spectropolarimetric surveys have established that a small but significant percentage of massive stars host stable, surface dipolar magnetic fields with strengths on the order of kG. These fields channel the dense, radiatively driven stellar wind into circumstellar magnetospheres, whose density and velocity structure can be probed using ultraviolet (UV) spectroscopy of wind-sensitive resonance lines. Coupled with appropriate magnetosphere models, UV spectroscopy provides a valuable way to investigate the wind–field interaction, and can yield quantitative estimates of the wind parameters of magnetic massive stars. We report a systematic investigation of the formation of UV resonance lines in slowly rotating magnetic massive stars with dynamical magnetospheres. We pair the analytic dynamical magnetosphere (ADM) formalism with a simplified radiative transfer technique to produce synthetic UV line profiles. Using a grid of models, we examine the effect of magnetosphere size, the line strength parameter, and the cooling parameter on the structure and modulation of the line profile. We find that magnetic massive stars uniquely exhibit redshifted absorption at most viewing angles and magnetosphere sizes, and that significant changes to the shape and variation of the line profile with varying line strengths can be explained by examining the individual wind components described in the ADM formalism. Finally, we show that the cooling parameter has a negligible effect on the line profiles.
Two procedures have been devised for tuning a photonic filter that comprises multiple whispering-gallery mode (WGM) disk resonators. As used here, tuning signifies locking the filter to a specific laser frequency and configuring the filter to obtain a desired high-order transfer function. The main problem in tuning such a filter is how to select the correct relative loading of the resonators to realize a prescribed filter function. The first of the two procedures solves this problem. As temperature gradients develop during operation, the spectra of individual resonators tend to drift, primarily because of the thermorefractive effect. Thus, there arises the additional problem of how to adjust the tuning during operation to maintain the desired transfer function. The second of the two procedures solves this problem. To implement the procedures, it is necessary to incorporate the resonators into an apparatus like that of Figure 1. In this apparatus, the spectrum of each resonator can be adjusted individually, via the electro-optical effect, by adjusting a bias voltage applied to that resonator. In addition, the positions of the coupling prisms and resonators can be adjusted to increase or reduce the gaps between them, thereby reducing or increasing, respectively, the optical coupling between them. The optical power (Pi) in resonator i is monitored by use of a tracking photodiode. Another tracking diode monitors the power reflected from the input terminal (Pr), and still others monitor the input power (Pin) and output power (Po). The readings of these photodiodes are used to guide the tuning adjustments described in this paper.