Results for “Characterizations” — Page 7

NASA NTRS2021

Optical Characterization of DebriSat Fragments in Support of Orbital Debris Environmental Models

The NASA Orbital Debris Program Office (ODPO) develops, maintains, and updates orbital debris environmental models, such as the NASA Orbital Debris Engineering Model (ORDEM), to support satellite designers and operators by estimating the risk from orbital debris impacts on their vehicles in orbit. Updates to ORDEM utilize the most recent validated datasets from radar, optical, and in situ sources to provide estimates of the debris flux as a function of size, material density, impact speed, and direction along a mission orbit. On-going efforts within the NASA ODPO to update the next version of ORDEM include a new parameter that highly affects the damage risk – shape. Shape can be binned by material density and size to better understand the damage assessments on spacecraft. The in situ and laboratory research activities at the NASA ODPO are focused on cataloging and characterizing fragments from a laboratory hypervelocity-impact test using a high-fidelity, mock-up satellite, DebriSat, in controlled and instrumented laboratory conditions. DebriSat is representative of present-day, low Earth orbit satellites, having been constructed with modern spacecraft materials and techniques. The DebriSat fragment ensemble provides a variety of shapes, bulk densities, and dimensions. Fragments down to 2 mm in size are being characterized by their physical and derived properties. A subset of fragments is being analyzed further in NASA’s Optical Measurement Center (OMC) using broadband, bidirectional reflectance measurements to provide insight into the optical-based NASA Size Estimation Model. Additionally, pre-impact spectral measurements on a subset of DebriSat materials were acquired for baseline material characterization. This paper provides an overview of DebriSat, the status of the project, and ongoing fragment characterization efforts within the OMC.

Heather M. Cowardin↗

NASA NTRSDate not supplied

Dynamic Characterization of NASA Armstrong Test Facility Mechanical Vibration Facility

In preparation for Sierra Nevada Corporation’s (SNC) Dream Chaser spacecraft vibration test campaign at NASA Armstrong Test Facility (ATF) in Sandusky, Ohio, a dynamic characterization of the Mechanical Vibration Facility (MVF) is currently ongoing. The Mechanical Vibration Facility is comprised of an 18 ft diameter annulus table that is driven with sixteen hydraulic vertical actuator assemblies and four hydraulic horizontal actuator assemblies. During a test campaign this allows for single axis vibration testing in the vertical axis and in each of the two orthogonal horizontal axes without the need for reconfiguring the test article. The dynamic characterization of the facility was defined to follow a building-block approach requiring three vibration test configurations: (1) MVF bare table (2) MVF table and head expander (3) MVF table, head expander, and a dummy test article. Following the completion of the facility dynamic characterization, a facility finite element model (FEM) will be test-verified allowing for more accurate pretest analysis used for determining response limits and abort levels. To date two of the three test configurations have been completed. Test results have been used to verify the facility FEM that includes both the 18 ft diameter annulus table and the aluminum head expander that fills in the center opening of the annulus to provide a continuous flat mounting surface. Both the MVF table and the head expander models were previously correlated using test results from free-free boundary condition modal tests so model updates to the facility FEM focused on the uncorrelated vertical actuator assemblies and horizontal actuator assemblies. The accuracy of the test-verified facility FEM will be further determined based on comparison of analytical and test results from the vibration test of the dummy test article. Efforts will also be made to determine fixed base modes of the test article attached to the flexible vibration table using fixed base correction techniques. This paper will discuss test and analytical results from the MVF dynamic characterization test sequence and corresponding model updating effort.

Emma L Pierson↗

NASA NTRSDate not supplied

Ray Tracing Techniques for the Characterization of Lunar Communication Architectures

This paper provides an overview of the computational techniques used to characterize the viability of different lunar architectures and their ability to provide communication services to the lunar surface. This analysis was done with modern ray tracing techniques that allow for the computations to be done on Graphics Processing Unit (GPU) clusters for a high level of parallelism and severe reduction in computation time. The ray tracing computations were done with the GPU platform Compute Unified Device Architecture (CUDA) provided by NVIDIA which utilizes general-purpose computing on graphics processing units (GPGPU). This new method provides the advantage of being able to characterize a much larger portion of the lunar surface due to its computational efficiency as well as providing a more accurate representation of elevation angle limits instead of the typical and often inaccurate elevation angle mask. The Lunar surface can now be characterized with metrics such as contact time, outage time, and received data rate. With these metrics, different proposed Lunar architectures can be rapidly evaluated. This reduction in computation time not only leads to more accurate results but allows these results to be obtained in a time frame that allows for the complete characterization of the trade space. It is expected that these different architecture comparisons will lead to a conclusive determination of the optimal Lunar architecture and will allow for future Lunar missions to operate as close to real time as possible. In addition, this computation method can be used to recreate visibility figures generated by previous methods but with an increased level of accuracy.

Thomas Montano↗

NASA NTRSDate not supplied

Spectral Characterization of Modern Spacecraft Materials

One of the observational parameters of interest in ground-based optical measurements is ascertaining material properties using broadband filter photometry and spectroscopy for orbiting targets. Broadband photometry can provide reflectance measurements that can aid in color-color indices and assess if objects can be classified into families or taxonomies. However, these reflectance properties can vary due to aspect angle, phase angle, and general degradation of the target’s exterior material. Spectral characterization can aid in material characterization utilizing known absorption bands and spectra signatures, but these signatures are affected by the same conditions described for remote observations. When utilizing ground-based measurements, it is well understood that material characterization is subject to variability due to space weathering and/or other external events (i.e., collision or explosion). The focus of this study is on space weathering effects on spacecraft materials in low Earth orbit. To better assess how materials are affected by the harsh space environment, specifically modern materials, a collection of materials was analyzed in both its pristine condition and after electron bombardment. This sample collection is part of an upcoming mission with the Materials International Space Station Experiment Flight Facility (MISSE-FF) that will be launched in 2022. These laboratory analyses on the samples will provide a ground truth to compare with the in-situ collected data. The data will also be stored in the NASA Johnson Space Center’s Spacecraft Materials Spectral Database that is available to U. S. citizens and maintained by the Orbital Debris Program Office. The following paper provides an overview of the materials investigated, laboratory and database overview, and spectral results for both pristine and post-electron exposed conditions. The spectral signature data highlights which materials are stable, or remain relatively unchanged, and which materials vary significantly due to exposure and material configuration (variations due to rotation of the sample on a flat surface). Initial results on changes in spectral directional reflectance of the materials as a function of incident illumination direction are also presented. This data also will benefit the space situational awareness community with spectral characterization of novel materials that can support their respective optical measurements focused on material identification.

Heather M Cowardin↗

NASA NTRSDate not supplied

Description of Cloud Characterization and Icing Test for a 3D Heated Test Article at the NASA Icing Research Tunnel

This paper describes the cloud characterization and icing tests conducted with a 3D heated test article in Winter/Spring 2022 at the NASA Icing Research Tunnel. The intent is to present analyzed results from these recently conducted tests in a future technical paper. The test article, whose geometry is representative of an inter-compressor duct and strut region of a turbofan engine, has been designed and constructed to study the physics of supercooled water icing and ice crystal icing. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, a scale to measure ice mass, and other instruments will aid in characterizing the icing behavior. The aim of these tests is to generate ice accretions on the SIDRM test article under well-characterized conditions. To that end, a suite of instruments was utilized to characterize the ice crystal clouds at the test section in a separate test series. The icing measurements collected during the SIDRM model tests will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assess the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost effective way.

Ice crystal icing↗

NASA NTRSDate not supplied

Description of Cloud Characterization and Icing Tests for a 3D Heated Test Article at the NASA Icing Research Tunnel

This paper describes the cloud characterization and icing tests conducted with a 3D heated test article in Winter/Spring 2022 at the NASA Icing Research Tunnel. The intent is to present analyzed results from these recently conducted tests in a future technical paper. The test article, whose geometry is representative of an inter-compressor duct and strut region of a turbofan engine, has been designed and constructed to study the physics of supercooled water icing and ice crystal icing. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, a scale to measure ice mass, and other instruments will aid in characterizing the icing behavior. The aim of these tests is to generate ice accretions on the SIDRM test article under well-characterized conditions. To that end, a suite of instruments was utilized to characterize the ice crystal clouds at the test section in a separate test series. The icing measurements collected during the SIDRM model tests will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assess the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost effective way.

Ice crystal icing, heated test article, engine ici↗

NASA NTRSDate not supplied

Spectral Characterization of Modern Spacecraft Materials

One of the observational parameters of interest in ground-based optical measurements is ascertaining material properties using broadband filter photometry and spectroscopy for orbiting targets. Broadband photometry can provide reflectance measurements that can aid in producing color-color indices and assess if objects can be classified into families or taxonomies. However, these reflectance properties can vary due to aspect angle, phase angle, and general degradation of the target’s exterior material. Spectral characterization can aid in material characterization utilizing known absorption bands and spectral signatures, but these signatures are affected by the same conditions described for remote observations.When utilizing ground-based measurements, it is well understood that material characterization is subject to variability due to space weathering and/or other external events (i.e., collision or explosion). The focus of this study is on space weathering effects on spacecraft materials in low Earth orbit. To better assess how materials are affected by the harsh space environment, specifically modern materials, a collection of materials were analyzed in both their pristine condition and after electron bombardment. This sample collection is part of an upcoming mission with the Materials International Space Station Experiment Flight Facility (MISSE-FF) that will be launched in 2022. These laboratory analyses on the samples will provide a ground-truth to compare with the insitu collected data. The data will also be stored in the NASA Johnson Space Center’s Spacecraft Materials Spectral Database that is available to U.S. citizens and maintained by the Orbital Debris Program Office. The following paper provides an overview of the materials investigated, laboratory, and database overview, and spectral results for both pristine and post-electron exposed conditions. The spectral signature data highlights which materials are stable, or remain relatively unchanged, and which materials vary significantly due to exposure and material configuration (variations due to rotation of the sample on a flat surface).Initial results on changes in spectral directional reflectance of the materials as a function of incident illumination direction are also presented.This data also will benefit the space situational awareness community with spectral characterization of novel materials that can support their respective optical measurements focused on material identification.

Heather M. Cowardin↗

NASA NTRS2016

Characterizing Rocky and Gaseous Exoplanets with 2 m Class Space-based Coronagraphs

Several concepts now exist for small, space-based missions to directly characterize exoplanets in reflected light. While studies have been performed that investigate the potential detection yields of such missions, little work has been done to understand how instrumental and astrophysical parameters will affect the ability of these missions to obtain spectra that are useful for characterizing their planetary targets. Here, we develop an instrument noise model suitable for studying the spectral characterization potential of a coronagraph-equipped, space-based telescope. We adopt a baseline set of telescope and instrument parameters appropriate for near-future planned missions like WFIRST-AFTA, including a 2 m diameter primary aperture, an operational wavelength range of 0.4–1.0 μm, and an instrument spectral resolution of λ/Δλ =70, and apply our baseline model to a variety of spectral models of different planet types, including Earth twins, Jupiter twins, and warm and cool Jupiters and Neptunes. With our exoplanet spectral models, we explore wavelength-dependent planet–star flux ratios for main-sequence stars of various effective temperatures and discuss how coronagraph inner and outer working angle constraints will influence the potential to study different types of planets. For planets most favorable to spectroscopic characterization—cool Jupiters and Neptunes as well as nearby super-Earths—we study the integration times required to achieve moderate signal-to-noise ratio spectra. We also explore the sensitivity of the integration times required to either detect the bottom or presence of key absorption bands (for methane, water vapor, and molecular oxygen) to coronagraph raw contrast performance, exozodiacal light levels, and the distance to the planetary system. Decreasing detector quantum efficiency at longer visible wavelengths makes the detection of water vapor in the atmospheres of Earth-like planets extremely challenging, and also hinders detections of the 0.89 μm methane band. Additionally, most modeled observations have noise dominated by dark currents, indicating that improving CCD performance could substantially drive down requisite integration times. Finally, we briefly discuss the extension of our models to a more distant future Large UV-Optical-InfraRed (LUVOIR) mission.

Astrobiology↗

NASA NTRSDate not supplied

Experimental Characterization of Non-Associative Plasticity Flow Rule Coefficients and Post-Peak Stress Degradation for the LS-DYNA MAT213 Model

This project is focused on developing an experimental framework for characterizing non-associative plasticity flow rule coefficients through coupon-scale tests for the LS-DYNA MAT213 model. The main objective is to characterize these coefficients based on the multi-scale (i.e., both microscopic and macroscopic) full-field measurement of the evolution of strain and stress fields. This paper focuses on presenting the experimental work on characterizing the full-scale stress-strain curves of T700/LM-PAEK composites under tension, compression, and shear loads. The experimental data set was intended to build a deformation sub-model in the MAT213 model for the material. The strain data were collected using both microscopic and macroscopic digital image correlation techniques. The microscopic technique was particularly useful for fracture cases under small strains. A preliminary simulation result obtained from the MAT213 model is also presented in the paper. The experimental framework herein will be extended to characterize post-peak stress degradation in the composite material and to develop a damage sub-model for the material. This project will contribute to developing a simulation tool based on the MAT213 model for simulating the rate-dependent impact damage in composites under multi-axial loading.

MAT213↗

NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

NASA NTRSDate not supplied

Electroluminescence Imaging: A Quantitative Characterization Technique to Measure Dust Occlusion of Solar Cells

Electroluminescence (EL) imaging is a qualitative characterization technique that is typically used to identify cracks, corrosion, and other defects in solar cells. It consists of imaging a cell under forward bias, where the solar cell emits photons due to radiative electron-hole pair recombination. Over the past few years, our team has expanded this into a quantitative technique with the help of image processing. We have primarily used this method to investigate lunar dust occlusion of solar cells and arrays. Lunar dust accumulation on solar cells is a major concern because it directly limits light accessible to the cell, decreasing power output. Many teams are working to develop dust mitigation technology to protect these arrays on the surface of the Moon, but thoroughly characterizing their efficacy is important to ensure their success prior to launch. Here, we present EL as a quantitative characterization technique to observe dust coverage on solar cells that, when coupled with IV performance measurements, can offer unique insights into how dust coverage impacts power output. Quantitative electroluminescence imaging works by running EL images through an image processing script that first grayscales the image then plots a histogram of the brightness of each pixel. On its own, it does not offer much insight into a solar cell’s performance. However, when comparing images to a baseline pristine, undamaged, or uncoated solar cell, it can quickly provide information about the impacts of surface contaminants or damage to the cell. Here, we present a case study where quantitative EL is used to measure the efficacy of dust mitigation technology for flexible solar arrays and discuss the lessons learned about dust mitigation, testing with lunar simulant, and this characterization technique.

photovoltaics↗

NASA NTRSDate not supplied

Understanding Relationships Between Satellite, Model, and Ground-Based Surface Temperature Characterizations From Overcast to Clear Conditions in Support of Satellite Remote Sensing of Clouds and Radiation

Accurate and consistent global estimates of cloud coverage and their properties are fundamental to long-term Earth radiation budget (ERB) monitoring efforts like the Clouds and the Earth’s Radiant Energy System (CERES) project. Cloud detection algorithms often apply thresholding approaches to identify where clouds occur by comparing satellite-measured radiances with those that are expected under cloud-free conditions. In addition, once a cloud is detected, the derivation of cloud optical and microphysical properties also requires knowledge of the background radiances below the cloud. In the infrared, knowledge of the surface emissivity and the expected skin temperature under both cloudy and cloud-free conditions is needed. These traits are generally well known over the oceans. Over land, however, comparisons between satellite-derived land surface temperature (LST) with that characterized in numerical weather analyses reveal large differences in many parts of the world, often exceeding 5 K, which can lead to significant satellite cloud detection and cloud property retrieval errors. Furthermore, clouds have a dramatic influence on the LST, and therefore characterization of that model parameter also depends on the capability of the model to accurately resolve clouds. Thus, the LST characterized in models is, at times, a poor approximation for what would otherwise be observed, thereby impeding accurate satellite cloud retrievals. As a result, we seek to develop a more robust method for estimating the LST required for satellite cloud characterizations. This effort is accomplished through a combination of surface emission/air temperature relationship studies in all-sky conditions using ground measurement stations, along with deep neural network (DNN) estimates of expected LST under overcast and cloud-free conditions. We demonstrate that substituting DNN-predicted LST for that generated by numerical models can mitigate model-inherent diurnal dependencies and reduce overall bias and uncertainty relative to satellite/ground observations by 0.5–4 K and 0.5–2 K, respectively. It is expected that this work will lead to improved satellite cloud retrievals that enhance ERB monitoring efforts.

B Scarino↗

NASA NTRS2026

Development, Characterization, and Validation of Elevated-Temperature Constitutive Models: Deformation and Damage

This report provides a brief review of experimentally observed hereditary and nonhereditary material behavior along with background information on standard as well as advanced internal state variable constitutive modeling at elevated temperature. A description of exploratory, characterization, and validation testing is presented along with a detailed outline of what constitutes “sufficient” data content (i.e., quality and quantity) for developing or enhancing, characterizing, and validating a particular sophisticated nonlinear time- and history-dependent (hereditary) class of constitutive models known as GVIPS (generalized viscoplasticity with potential structure). The tests described are necessary to reveal a material’s behavior in the reversible (or viscoelastic) and irreversible (or viscoplastic) regimes, for the identification of both deformation and damage model parameters. Results presented are primarily for metallic materials. In all cases, both uniaxial and multiaxial tests are described, and the linkage between the specific tests and the parameters within the model that can be characterized from the results of these tests are also discussed. Discussion is also provided relative to the role information management must play relative to material data collection, analysis, maintenance, and dissemination. The need for such an information system is particularly important as both analyst and designer move toward utilizations of sophisticated, nonlinear time- and history dependent (hereditary) constitutive models. Lastly, the concept of state space and its utility in understanding and establishing constitutive models is addressed throughout. The intent behind this document is to help both the modeler and experimentalist understand each other’s specific points of view and provide guidance for both model development and characterization. Emphasis has been placed on providing the mechanician with information regarding how tests are performed and what issues to be aware of when interpreting results. It is hoped that experimentalists will take away a new perspective on the types of information that modelers and analysts are looking for from them.

Constitutive Modeling↗

NASA NTRS2014

Characterizing the Physical and Thermal Properties of Planetary Regolith at Low Temperatures

The success or failure of in-situ resource utilization for planetary surface exploration-whether for science, colonization, or commercialization-relies heavily on the design and implementation of systems that can effectively process planetary regolith and exploit its potential benefits. In most cases, this challenge necessarily includes the characterization of regolith properties at low temperatures (cryogenic). None of the nearby solar system destinations of interest, such as the moon, Mars and asteroids, possess a sufficient atmosphere to sustain the consistently "high" surface temperatures found on Earth. Therefore, they can experience permanent cryogenic temperatures or dramatic cyclical changes in surface temperature. Characterization of physical properties (e.g., specific heat, thermal and electrical conductivity) over the entire temperature profile is important when planning a mission to a planetary surface; however, the impact on mechanical properties due to the introduction of icy deposits must also be explored in order to devise effective and robust excavation technologies. The Granular Mechanics and Regolith Operations Laboratory and the Cryogenics Test Laboratory at NASA Kennedy Space Center are developing technologies and experimental methods to address these challenges and to aid in the characterization of the physical and mechanical properties of regolith at cryogenic temperatures. This paper will review the current state of knowledge concerning planetary regolith at low temperature, including that of icy regolith, and describe efforts to manipulate icy regolith through novel penetration and excavation techniques.

Characterizing the Physical and Thermal Properties↗

NASA NTRS2015

Dynamic Characterization of Galfenol

A novel and precise characterization of the constitutive behavior of solid and laminated research-grade, polycrystalline Galfenol (Fe81:6Ga18:4) under under quasi-static (1 Hz) and dynamic (4 to 1000 Hz) stress loadings was recently conducted by the authors. This paper summarizes the characterization by focusing on the experimental design and the dynamic sensing response of the solid Galfenol specimen. Mechanical loads are applied using a high frequency load frame. The dynamic stress amplitude for minor and major loops is 2.88 and 31.4 MPa, respectively. Dynamic minor and major loops are measured for the bias condition resulting in maximum, quasi-static sensitivity. Three key sources of error in the dynamic measurements are accounted for: (1) electromagnetic noise in strain signals due to Galfenol's magnetic response, (2) error in load signals due to the inertial force of fixturing, and (3) time delays imposed by conditioning electronics. For dynamic characterization, strain error is kept below 1.2 % of full scale by wiring two collocated gauges in series (noise cancellation) and through lead wire weaving. Inertial force error is kept below 0.41 % by measuring the dynamic force in the specimen using a nearly collocated piezoelectric load washer. The phase response of all conditioning electronics is explicitly measured and corrected for. In general, as frequency increases, the sensing response becomes more linear due to an increase in eddy currents. The location of positive and negative saturation is the same at all frequencies. As frequency increases above about 100 Hz, the elbow in the strain versus stress response disappears as the active (soft) regime stiffens toward the passive (hard) regime.

Dynamic sensing↗

NASA NTRS2017

Characterizing Response Versus Scan-Angle for MODIS Reflective Solar Bands Using Deep Convective Clouds

MODIS consists of a cross-track, two-sided scan mirror, whose reflectance is not uniform but is a function of angle of incidence (AOI). This feature, known as response versusscan-angle (RVS), was characterized for all reflective solar bands of both MODIS instruments prior to launch. The RVS characteristic has changed on orbit, which must be tracked precisely over time to ensure the quality of MODIS products. The MODIS characterization support team utilizes the onboard calibrators and the earth view responses from multiple pseudo invariant desert sites to track the RVS changes at different AOIs. The drawback of using deserts is the assumption that these sites are radiometrically stable during the monitoring period. In addition, the 16-day orbit repeat cycle of MODIS allows for only a limited set of AOIs over a given desert. We propose a novel and robust approach of characterizing the MODIS RVS using tropical deep convective clouds (DCC). The method tracks the monthly DCC response at specified sets of AOIs to compute the temporal RVS changes. Initial results have shown that the Aqua-MODIS collection 6 band 1 level 1B radiances show considerable residual RVS dependencies, with long-term drifts up to 2.3 at certain AOIs.

Clouds↗

NASA NTRS2019

Characterization and Failure Analysis of 650 V Enhancement-Mode GaN HEMT for Cryogenically-Cooled Power Electronics

In order to evaluate the feasibility of newly developed GaN devices in a cryogenically-cooled converter, this paper characterizes a 650 V enhancement-mode Gallium-Nitride high-electron-mobility transistor (GaN HEMT) at cryogenic temperatures. The characterization includes both static and dynamic behaviors. The results show that this GaN HEMT is an excellent device candidate to be applied in cryogenic-cooled applications. For example, transconductance at cryogenic temperature (93 K) is 2.5 times higher than one at room temperature (298 K), and accordingly, peak di/dt during turn-on transients at cryogenic temperature is around 2 times of that at room temperature. Moreover, the on-resistance of the channel at cryogenic temperature is only one-fifth of that at room temperature. The corresponding explanations of performance trends at cryogenic temperatures are also given from the view of semiconductor physics. In addition, several device failures were observed during the dynamic characterization of GaN HEMTs at cryogenic temperatures. The ultra-fast switching speed induced high di/dt and dv/dt at cryogenic temperatures amplifies the negative effects of parasitics inside the switching loop. Based on failure waveforms, two failure modes were classified, and detailed failure mechanisms caused by ultra-fast switching speed are given in this paper.

Static and dynamic characterization↗