Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Catalyst Flow Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Nondestructive neutron imaging diagnosis of acidic gas reduction catalyst after 400-Hour operation in natural gas furnace

Residential natural gas furnaces are the primary space-heating devices in US homes, leading to substantial environmental impact caused by the acidic components in the furnace combustion gases. Here, to experimentally demonstrate acidic gas reduction in a furnace, a monolithic catalyst was fabricated and was called the AGR. A commercially-available condensing furnace was retrofitted with the AGR, and a 400-hour reliability and durability test was conducted. The results showed that the AGR significantly reduced acidic gases in the flue gas and produced condensate with neutral pH. Challenges were also revealed: inappropriate condensate drainage caused incomplete combustion and amorphous carbon deposits. To nondestructively survey the internal state of the AGR, neutron computed tomography (NCT) was employed to produce spatially resolved 2D and 3D representations of the 2-L, aged AGR component. The NCT results confirm the integrity of the AGR component, which consists of two blocks, without deformation or damage to AGR channels. The distribution of the particle accumulation in the middle of the top block was visibly heavier than the entrance and exit of the top block. The representative cross-section views revealed significant aggregation in the central region but not at the rim. The spatially resolved details provide in-depth diagnosis, evaluation, and understanding of the AGR. The insights can enable new AGR designs that realize a uniform and self-cleaning flow pattern, alleviate significant particle aggregation, and thus enhance AGR-enabled furnace performance. The neutron imaging method demonstrates the good potential that can diagnose faults and improve the design, optimization, and production processes of novel catalysts and other components or systems with heavy metal shell.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Optimizing Porous Transport Layer Porosity for Proton Exchange Membrane Water Electrolysis

An empirical model is presented that describes anode-side losses related to porous transport layer (PTL) morphology in proton exchange membrane water electrolysis (PEMWE). The model is based on an advanced voltage breakdown analysis that links various overpotentials to PTL morphology. Custom Ti PTLs, spanning uncommonly low porosities (22 - 31%), were fabricated and analyzed with X-ray CT to obtain pore and particle size distributions. Particle size distributions were consistent across samples with an average particle diameter of 12.0?..mu..m, whereas average pore diameters ranged from 6.0 to 7.0?..mu..m. The PTLs were tested in standard PEMWE cell assemblies with anode catalyst loadings of 0.1 mgIr cm-2 to obtain polarization curves, electrochemical impedance spectra, and augmented Tafel analysis. The PTL-dependent anode side losses were deconvoluted and assigned to excess utilization, concentration, ion transport resistance, and electrical contact resistance overpotentials. The data and model reveal an optimal 20 - 28% PTL porosity region where utilization and contact resistance overpotentials are minimized without triggering concentration and ion transport losses related to water deprivation. The optimal PTL porosity depends on the operating current density and is demonstrated at realistic PEMWE water flow rates to establish PTL design guidance for operation at scale.

08 HYDROGEN↗
DOE OSTI2026

Towards a Unified Low-Cost Flow Plate, Flow-Field, PTL Solution for Proton Exchange Membrane Electrolyzers

Proton exchange membrane (PEM) water electrolysis is a highly efficient method for hydrogen production. Research cells typically consist of one proton exchange membrane, two catalyst layers, two porous transport layers, two flow-field plates, and two endplates. In commercial systems, the machined flow-field plates that are employed in research cells are typically replaced by stamped parts or open mesh material solutions to reduce manufacturing cost at scale. Nonetheless, the cell contains about 8 total interfaces: bipolar plate / flow plate material / porous transport medium / electrode / membrane / electrode / porous transport medium / flow plate material / bipolar plate. All these materials and interfaces need to be optimized for maximum performance and efficiency. Reducing the amount of interfaces by combining individual cell components directly benefits the fabrication cost (by reducing the parts count and the needs for surface coatings) and the electrochemical performance (by reducing ohmic losses). We have designed a novel PEM electrolysis cell with a piece of channeled titanium felt functioning as both the anode flow-field and the PTL, referred to as the channeled diffusion layer (CDL). The pores of the felt facilitate both in-plane and through-plane diffusion, ensuring maximum catalyst utilization while also minimizing mass transport loss. The titanium felt can be mass manufactured with existing stamping and forming methods and is therefore a promising candidate to reduce the capital cost of PEM electrolyzers whilst improving hydrogen production efficiency. Experiments conducted with 3mg IrOx/cm2 loading MEAs have shown a approximately 40% boost in peak current by implementing the CDL design. Low catalyst-loading MEAs are being tested in ongoing experiments and their results will be discussed and compared.

08 HYDROGEN↗
NASA NTRS2003

Catalyzed Combustion of Bipropellants for Micro-Spacecraft Propulsion

This paper addresses the need to understand the physics and chemistry involved in propellant combustion processes in micro-scale combustors for propulsion systems on micro-spacecraft. These spacecraft are planned to have a mass less than 50 kilograms with attitude control estimated to be in the 10 milli-Newton thrust class. These combustors are anticipated to be manufactured using Micro Electrical Mechanical Systems (MEMS) technology and are expected to have diameters approaching the quenching diameter of the propellants. Combustors of this size are expected to benefit significantly from surface catalysis processes. Miniature flame tube apparatus is chosen for this study because microtubes can be easily fabricated from known catalyst materials and their simplicity in geometry can be used in fundamental simulations for validation purposes. Experimentally, we investigated the role of catalytically active surfaces within 0.4 and 0.8 mm internal diameter microtubes, with special emphases on ignition processes in fuel rich gaseous hydrogen and gaseous oxygen. Flame thickness and reaction zone thickness calculations predict that the diameters of our test apparatus are below the quenching diameter of the propellants in sub-atmospheric tests. Temperature and pressure rise in resistively heated platinum and palladium microtubes was used as an indication of exothermic reactions. Specific data on mass flow versus preheat temperature required to achieve ignition are presented. With a plug flow model, the experimental conditions were simulated with detailed gas-phase chemistry, thermodynamic properties, and surface kinetics. Computational results generally support the experimental findings, but suggest an experimental mapping of the exit temperature and composition is needed.

Schneider, Steven J.↗
DOE OSTI2024

A simultaneous depolymerization and hydrodeoxygenation process to produce lignin-based jet fuel in continuous flow reactor

Economical production of lignin-based jet fuel (LJF) can improve the sustainability of sustainable aviation fuels (SAFs) as well as can reduce the overall greenhouse gas emissions. However, the challenge lies in converting technical lignin polymer from biorefinery directly to jet fuel in a continuous operation. In this work, we demonstrate a simultaneous depolymerization and hydrodeoxygenation (SDHDO) process to produce lignin-based jet fuel from the alkali corn stover lignin (ACSL) using engineered Ru-HY-60-MI catalyst in a continuous flow reactor at first time. The maximum carbon yield of LJF of 17.9wt% was obtained, and it comprised of 60.2wt% monocycloalkanes, and 21.6wt% polycycloalkanes. Catalyst characterization of Ru-HY-60-MI suggested there was no significant change in HY zeolite structure and its crystallinity after catalyst engineering. Catalyst characterizations performed post the SDHDO experiments indicate presence of carbon and K content in the catalyst. K content presence in the spent catalyst was due to K + ion was exchanged between lignin solution and HY-60 while carbon presence validated the SDHDO chemistry on the catalyst surface. Tier a fuel property testing indicates that LJF production using SDHDO chemistry can offer SAF with high compatibility, good sealing properties, low emissions, and high energy density for aircraft.

09 BIOMASS FUELS↗
NASA NTRS1975

Advanced Low NO Sub X Combustors for Supersonic High-Altitude Aircraft Gas Turbines

A test rig program was conducted with the objective of evaluating and minimizing the exhaust emissions, in particular NO sub x, of three advanced aircraft combustor concepts at a simulated, high altitude cruise condition. The three combustor designs, all members of the lean reaction, premixed family, are the Jet Induced Circulation (JIC) combustor, the Vortex Air Blast (VAB) combustor, and a catalytic combustor. They were rig tested in the form of reverse flow can combustors in the 0.127 m. (5.0 in.) size range. Various configuration modifications were applied to each of the initial JIC and VAB combustor model designs in an effort to reduce the emissions levels. The VAB combustor demonstrated a NO sub x level of 1.1 gm NO2/kg fuel with essentially 100% combustion efficiency at the simulated cruise combustor condition of 50.7 N/sq cm (5 atm), 833 K (1500 R) inlet pressure and temperature respectively and 1778 K (3200 R) outlet temperature on Jet-A1 fuel. Early tests on the catalytic combustor were unsuccessful due to a catalyst deposition problem and were discontinued in favor of the JIC and VAB tests. In addition emissions data were obtained on the JIC and VAB combustors at low combustor inlet pressure and temperatures that indicate the potential performance at engine off-design conditions.

Roberts, P. B.↗
DOE OSTI2021

NREL's HydroGEN Photoreactor Platform Design and Characterization

This technical report details the design, fabrication, and construction of a flow-through photoreactor developed at The National Renewable Energy Laboratory (NREL). The photoreactor is designed to facilitate indoor or outdoor testing on photoelectrochemical or integrated solar water splitting devices. The photoreactor design described here is based on a previous demonstration. The photoreactor version described herein contains several advanced design features that include: 1) Chassis-chuck two-part design, 2) Separable counter electrode compartments (here, the counter electrodes are anodes), 3) Reduced electrode separation to reduce electrolyte resistance, 4) Improved flow pattern for bubble removal, 5) Mounting for spectroradiometer receptor, 6) Fresnel lens and collimating tube attachments. The photoreactor presented here was designed primarily to accommodate photocathode materials in an illuminated compartment and a dark anode as the oxygen evolution catalyst. The build materials were thus chosen to for acid electrolyte compatibility. Other embodiments could accommodate a photoanode with dark hydrogen evolution catalyst and other build materials for alkaline compatibility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Probing the Transformation of Boron Nitride Catalysts under Oxidative Dehydrogenation Conditions

Hexagonal boron nitride (h-BN) and boron nitride nanotubes (BNNTs) were recently reported as highly selective catalysts for the oxidative dehydrogenation (ODH) of alkanes to olefins in the gas phase. Previous studies revealed a substantial increase in surface oxygen content after exposure to ODH conditions (heating to ca. 500 °C under a flow of alkane and oxygen); however, the complexity of these materials has thus far precluded an in-depth understanding of the oxygenated surface species. In this contribution, we combine advanced NMR spectroscopy experiments with scanning electron microscopy (SEM) and soft X-ray absorption spectroscopy (XAS) to characterize the molecular structure of the oxygen functionalized phase that arises on h-BN and BNNTs following catalytic testing for ODH of propane. The pristine BN materials are readily oxidized and hydrolyzed under ODH reaction conditions to yield a phase consisting of three coordinate boron sites with variable numbers of hydroxyl and bridging oxide groups which is denoted B(OH) x O 3-x (where x = 0-3). Evidence for this robust oxide phase revises previous literature hypotheses of hydroxylated BN edges as the active component on h-BN.

03 NATURAL GAS↗
NASA NTRS1993

Validation test of 125 Ah advanced design IPV nickel-hydrogen flight cells

An update of validation test results confirming the advanced design nickel-hydrogen cell is presented. An advanced 125 Ah individual pressure vessel (IPV) nickel-hydrogen cell was designed. The primary function of the advanced cell is to store and deliver energy for long-term, Low-Earth-Orbit (LEO) spacecraft missions. The new features of this design, which are not incorporated in state-of-the-art design cells, are: (1) use of 26 percent rather than 31 percent potassium hydroxide (KOH) electrolyte; (2) use of a patented catalyzed wall wick; (3) use of serrated-edge separators to facilitate gaseous oxygen and hydrogen flow within the cell, while still maintaining physical contact with the wall wick for electrolyte management; and (4) use of a floating rather than a fixed stack (state-of-the-art) to accommodate nickel electrode expansion due to charge/discharge cycling. The significant improvements resulting from these innovations are extended cycle life; enhanced thermal, electrolyte, and oxygen management; and accommodation of nickel electrode expansion. Six 125 Ah flight cells based on this design were fabricated by Eagle-Picher. Three of the cells contain all of the advanced features (test cells) and three are the same as the test cells except they do not have catalyst on the wall wick (control cells). All six cells are in the process of being evaluated in a LEO cycle life test at the Naval Weapons Support Center, Crane, IN, under a NASA Lewis Research Center contract. The catalyzed wall wick cells have been cycled for over 19000 cycles with no cell failures in the continuing test. Two of the noncatalyzed wall wick cells failed (cycles 9588 and 13,900).

Smithrick, John J.↗
NASA NTRS2020

Additive Manufactured Ultra-Fine Lattice Structures for Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultrafine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray microfocus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar R Mireles↗
NASA NTRSDate not supplied

Additive Manufacture of Ultra-Fine Lattice Structures of Green Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultrafine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray microfocus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar Mireles↗
NASA NTRS1972

Characteristics of individuals with high information potential in government research and development organizations.

In order to study focal individuals within informal communications networks, a special variable was constructed: information potential (IP) was defined as the information-source value placed on an individual by his colleagues. Four hypotheses involving IP were tested in three R&D organizations using questionnaires and pencil-and-paper tests. Results indicated that the individual with high IP used more and different sources of technical information, was seen to be a credible information source and to have a strong ability to associate seemingly unrelated ideas, and was as approachable as the other members of his organization. Four tentative conclusions may be drawn from this study concerning the person with high IP. He is (1) an identifiable individual in several different kinds of organizations; (2) a distinctive information transceiver (transmitter and receiver); (3) both a producer and a catalyst in his own organization; and (4) an extender and an amplifier of information search. To affect the efficiency of informal information flow, the research manager's best hope for positively influencing informal networks lies in the identification and motivation of the special communicators in his organization.

Holland, W. E.↗
NASA NTRS2008

NASA Tech Briefs, February 2008

Topics discussed include: Optical Measurement of Mass Flow of a Two-Phase Fluid; Selectable-Tip Corrosion-Testing Electrochemical Cell; Piezoelectric Bolt Breakers and Bolt Fatigue Testers; Improved Measurement of B(sub 22) of Macromolecules in a Flow Cell; Measurements by a Vector Network Analyzer at 325 to 508 GHz; Using Light to Treat Mucositis and Help Wounds Heal; Increasing Discharge Capacities of Li-(CF)(sub n) Cells; Dot-in-Well Quantum-Dot Infrared Photodetectors; Integrated Microbatteries for Implantable Medical Devices; Oxidation Behavior of Carbon Fiber-Reinforced Composites; GIDEP Batching Tool; Generic Spacecraft Model for Real-Time Simulation; Parallel-Processing Software for Creating Mosaic Images; Software for Verifying Image-Correlation Tie Points; Flexcam Image Capture Viewing and Spot Tracking; Low-Pt-Content Anode Catalyst for Direct Methanol Fuel Cells; Graphite/Cyanate Ester Face Sheets for Adaptive Optics; Atomized BaF2-CaF7 for Better-Flowing Plasma-Spray Feedstock; Nanophase Nickel-Zirconium Alloys for Fuel Cells; Vacuum Packaging of MEMS With Multiple Internal Seal Rings; Compact Two-Dimensional Spectrometer Optics; and Fault-Tolerant Coding for State Machines.

Source record↗
NASA NTRSDate not supplied

Additive Manufactured Ultra-Fine Lattice Structures for Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultra-fine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray micro-focus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar R Mireles↗
NASA NTRS2003

Catalyzed Ignition of Bipropellants in Microtubes

This paper addresses the need to understand the physics and chemistry involved in propellant combustion processes in micro-scale combustors for propulsion systems on micro-spacecraft. These spacecraft are planned to have a mass less than 50 kilograms with attitude control estimated to be in the 10 milli-Newton thrust class. These combustors are anticipated to be manufactured using Micro Electrical Mechanical Systems (MEMS) technology and are expected to have diameters approaching the quenching diameter of the propellants. Combustors of this size are expected to benefit significantly from surface catalysis processes. Miniature flame tube apparatus is chosen for this study because microtubes can be easily fabricated from known catalyst materials and their simplicity in geometry can be used in fundamental simulations to more carefully characterize the measured heat transfer and pressure losses for validation purposes. Experimentally, we investigate the role of catalytically active surfaces within 0.4 and 0.8 mm internal diameter micro-tubes, with special emphases on ignition and extinction processes in fuel rich gaseous hydrogen and gaseous oxygen. Flame thickness and reaction zone thickness calculations predict that the diameters of our test apparatus are below the quenching diameter of the propellants in sub-atmospheric tests. Temperature and pressure rises in resistively heated platinum and palladium micro-tubes are used as an indication of exothermic reactions. Specific data on mass flow versus preheat temperature required to achieve ignition are presented.

Schneider, Steven J.↗
DOE OSTI2019

De-pollution efficacy of photocatalytic roofing granules

Photocatalytic building surfaces can harness sunlight to reduce urban air pollution. The NO x abatement capacity of TiO 2 -coated granules used in roofing products was evaluated for commercial product development. A laboratory test chamber and ancillary setup were built following conditions prescribed by ISO Standard 22197-1. It was validated by exposing reference P25-coated aluminum plates to a 3 L min -1 air flow enriched in 1 ppm NO under UVA irradiation (360 nm, 11.5 W m -2 ). We characterized prototype granule-surfaced asphalt shingles and loose granules prepared with different TiO 2 loadings and post-treatment formulations. Tests performed at surface temperatures of 25 and 60 °C showed that NO x abatement was more effective at the higher temperature. Preliminary tests explored the use of 1 ppm NO 2 and of 1 ppm and 0.3 ppm NO/NO 2 mixtures. Specimens were aged in a laboratory accelerated weathering apparatus, and by exposure to the outdoor environment over periods that included dry and rainy seasons. Laboratory aging led to higher NO removal and NO 2 formation rates, and the same catalyst activation was observed after field exposure with frequent precipitation. However, exposure during the dry season reduced the performance. This inactivation was mitigated by cleaning the surface of field-exposed specimens. Doubling the TiO 2 loading led to a 50–150% increase in NO removal and NO x deposition rates. Finally, application of different post-treatment coatings decreased NO removal rates (21–35%) and NO x deposition rates (26–74%) with respect to untreated granules. The mass balance of nitrogenated species was assessed by extracting granules after UV exposure in a 1 ppm NO-enriched atmosphere.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2013

Development and Testing of a Green Monopropellant Ignition System

This paper will detail the development and testing of a "green" monopropellant booster ignition system. The proposed booster ignition technology eliminates the need for a pre-heated catalyst bed, a high wattage power source, toxic pyrophoric ignition fluids, or a bi-propellant spark ignitor. The design offers the simplicity of a monopropellant feed system features non-hazardous gaseous oxygen (GOX) as the working fluid. The approach is fundamentally different from all other "green propellant" solutions in the aerospace in the industry. Although the proposed system is more correctly a "hybrid" rocket technology, since only a single propellant feed path is required, it retains all the simple features of a monopropellant system. The technology is based on the principle of seeding an oxidizing flow with a small amount of hydrocarbon.1 The ignition is initiated electrostatically with a low-wattage inductive spark. Combustion gas byproducts from the hydrocarbon-seeding ignition process can exceed 2400 C and the high exhaust temperature ensures reliable main propellant ignition. The system design is described in detail in the Hydrocarbon-Seeded Ignition System Design subsection.

Whitmore, Stephen A.↗
DOE OSTI2021

The Effect of Spark-Plug Heat Dispersal Range and Exhaust Valve Opening Timing on Cold-Start Emissions and Cycle-to-Cycle Variability

The partnership for advancing combustion engines (PACE) is a US Department of Energy consortium involving multiple national laboratories and includes a goal of addressing key efficiency and emission barriers in light-duty engines fueled with a market-representative E10 gasoline. A major pillar of the initiative is the generation of detailed experimental data and modeling capabilities to understand and predict cold-start behavior. Cold-start, as defined by the time between first engine crank and three-way catalyst light-off, is responsible for a large percentage of NOx, unburned hydrocarbon and particulate matter emissions in light-duty engines. Minimizing emissions during cold-start is a trade-off between achieving faster light-off of the three-way catalyst and engine out emissions during that period. In this study, gaseous and soot emissions were measured at a distance representative of the three-way catalyst position downstream of the engine at a 2 bar net indicated mean effective pressure (NIMEP) steady-state operating condition representative of cold-start. The test matrix included sweeps of ignition timing 15 degrees-before to 10 degrees-after top dead center firing (TDCf) across three different spark-plug heat dispersal ranges (HR). Additionally, the effect of varying exhaust valve opening (EVO) timing on combustion stability and emissions was also studied. Results show that the spark plug HR affects the coefficient of variation (COV) of NIMEP under all cold-start conditions, while the impact on emissions was found to be minimal. At very retarded spark timings, colder spark plugs required higher air and fuel flow to maintain the desired 2bar NIMEP load, but the fraction of fuel energy going into the exhaust was found to be similar for all spark plugs. Finally, retarding exhaust valve timings showed a simultaneous reduction in emissions while increasing the fraction of fuel energy being fed into the exhaust. However, engine COV was also observed to increase with retarded exhaust timings.

42 ENGINEERING↗