Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Casting Modeling Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Senary refractory high-entropy alloy Cr x MoNbTaVW

This paper demonstrates that a senary refractory high-entropy alloy Cr x MoNbTaVW can be tailored over a certain range of Cr content with the BCC structure for different microstructures and physical properties, assisted by CALPHAD simulations. Microstructure characterizations are performed using X-ray diffraction and scanning electron microscopy. Chemical microsegregation during solidification predicted using the Scheil model generally agrees with the experimental results. The lattice constant, density, and Vickers’ micro-hardness of the highentropy alloy samples in the as-cast state are measured and discussed. For Cr x MoNbTaVW, x=2.0 case appears exceeding the upper limit of maintaining a single BCC phase HEA, determined by the XRD patterns. The elemental dependence of the mixing thermodynamic properties (entropy, enthalpy and Gibbs energy) in BCC phase in the senary system is analyzed. The calculated entropy of mixing and enthalpy of mixing for CrMoNbTaVW are 14.7 J/K/mol and -662.5 J/mol respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Concrete Structure Health Monitoring Using Vibro-acoustic Testing and Machine Learning

Assessment and management of aging concrete structures in nuclear power plants require a more systematic approach than simple reliance on margins of safety in existing codes. Research is required to deploy online monitoring capability to assess the health of concrete structures in nuclear power plants and perform predictive analytics based on heterogeneous measurements, in order to reduce the operation and maintenance costs. The research effort described in this report focuses on the health monitoring of concrete slabs containing reactive aggregates using the vibro-acoustic modulation (VAM) technique and predictive modeling. The research is developing an approach to enable detection, localization, and estimation of the extent of degradation in concrete slabs due to alkali-silica reaction (ASR). The project outcomes are generic and extendable to other degradation modes in concrete. A concrete slab without reinforcements was cast at Vanderbilt University and cured in aggressive conditions to accelerate ASR degradation. In this report, we develop a methodology for the automation of VAM testing, and the construction of machine learning models to facilitate damage localization in concrete structures. We investigate how machine learning models based on physics simulation data can be effectively utilized for damage localization (damage location and depth) and estimation in a concrete slab specimen. Our study indicates that these models could potentially support damage localization and estimation for NPP structures.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Accelerated fission rate irradiation design, pre-irradiation characterization, and adaptation of conventional PIE methods for U-10Mo and U-17Mo

Metallic U alloys have high U density and thermal conductivity and thus have been explored since the beginning of nuclear power research. Alloys of U with modest amounts of Mo, such as U-10 wt % Mo (U-10Mo), are of particular interest because the γ-U crystal structure in this alloying addition shows prolonged stability in reactor service. Historically, radiation data on U-10Mo fuels were collected in Na fast reactors or lower temperature research reactor conditions, but little is known about irradiation behavior, particularly swelling and creep, at irradiation temperatures between 250 and 500°C. This work discusses the methodology and pre-irradiation characterization results from a U-Mo irradiation campaign performed in the High Flux Isotope Reactor at Oak Ridge National Laboratory. U-10Mo and U-17Mo samples irradiations are being completed at temperatures ranging from 250 to 500°C to three targeted fission densities between 2 × 10 20 and 1.5 × 10 21 fissions per cubic centimeter. Swelling measurement of the specimen sizes studied here required development and assessment of new methods for volume determination before and after irradiation. Laser profilometry and X-ray computation tomography (XCT) were used to provide preirradiation characterization of samples to determine the error and applicability of each to determine swelling following irradiation. These outcomes are contextualized through use of BISON simulations performed to assess the predicted expansion of U-Mo fuels subjected to the irradiation conditions of this work. Use of existing BISON fuel performance models predicted a maximum of 7% swelling under the irradiation conditions of this study. Pre-irradiation characterization revealed the as-cast U-Mo fuel samples were uniformly large-grained fully cubic U crystals with small U-C/N bearing precipitates and pores distributed throughout. Samples were found to contain a bulk porosity between .4 and 3% because of the casting process. Local porosity in areas far from large, interconnected pores was found by Slice-and-View to be under .2%. Nanometer-sized precipitates rich in C and N were identified in all samples, likely because of impurities during the fabrication process. Dendritic bands were also observed throughout the samples. These bands were characterized by variable Mo content that deviated from the overall Mo content by 2–3 wt %. No other microstructural features were correlated to these bands. Mechanical properties were found to be slightly strengthened compared to literature reports of bulk U-Mo fuels due to the nano-scale precipitates throughout the sample.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Monte Carlo simulations of Cu/Ni–Si–Mn co-precipitation in duplex stainless steels

First-Passage Kinetic Monte Carlo (FPKMC) simulations of species migration in duplex stainless steels were performed in order to establish relationships between alloy content, segregation behavior, and the formation of Ni-Si-Mn rich particles in cast duplex stainless steels during thermal aging. The Ni-Si-Mn-rich second phase forms after extended aging at reactor operating temperatures and degrades alloy properties. Simulations of Ni-Si-Mn cluster formation were validated through comparison with experimental results obtained through Atom Probe Tomography (APT) on similar alloy compositions, identifying several trends. First, Cu promotes the formation of Ni-Si-Mn clusters, but only when Ni or Mn prefer segregation to the surface of Cu particles; without the segregation of these species, the critical composition for the clusters to form was not achieved. Second, the width of precipitate-denuded zones near ?/d interfaces increases with decreasing Cu content. This finding was in strong agreement with APT results, further validating our model. Finally, our model predicts that Ni-Si-Mn cluster formation will be the most extensive when the Si:Mn ratio is approximately 1:1 and the least extensive when one of these key elements is less concentrated (Mn = 0.5 at.% or Si = 0.5 at.%). The implications of these results on how to improve alloy properties are discussed.

Cu co-precipitation, Atom probe tomography (APT), ↗
DOE OSTI2018

Analysis of the Impact of Installation Parameters and System Size on Bifacial Gain and Energy Yield of PV Systems

In this work, we present the combined effect of installation parameters (tilt angle, height above ground, and albedo) on the bifacial gain and energy yield of three photovoltaic (PV) system configurations: a single module, a row of five modules, and five rows of five modules utilizing RADIANCE based ray tracing model. We show that optimum tilt angle is dependent on parameters such as height, albedo, size of the system, and time of the year. For a single bifacial module installed in Albuquerque, NM, the optimum tilt angle is lowest (~5 degree) for summer solstice and highest (~65 degree) for winter solstice. For larger systems, optimum tilt angle can be up to 200 more than that for a single module system. We also show that modules in large scale systems, generate lower energy due to large shadowing areas cast by the modules on the ground. For albedo of 21 %, middle module in a large array generates up to 7% less energy than a single bifacial module. To validate our model, we utilize measured data from Sandia's fixed tilt bifacial PV testbed and compare it with our simulations. We find that due to higher non-uniformity, lower tilt angles demonstrate high normalized root mean square deviation (NRMSD) between measured and simulated values than high tilt angles.

14 SOLAR ENERGY↗
DOE OSTI2018

Numerical Simulation of Bulging Deformation for Wide-Thick Slab Under Uneven Cooling Conditions

In the present work, the bulging deformation of a wide-thick slab under uneven cooling conditions was studied using finite element method. The non-uniform solidification was first calculated using a 2D heat transfer model. The thermal material properties were derived based on a microsegregation model, and the water flux distribution was measured and applied to calculate the cooling boundary conditions. Based on the solidification results, a 3D bulging model was established. The 2D heat transfer model was verified by the measured shell thickness and the slab surface temperature, and the 3D bulging model was verified by the calculated maximum bulging deflections using formulas. The bulging deformation behavior of the wide-thick slab under uneven cooling condition was then determined, and the effect of uneven solidification, casting speed, and roll misalignment were investigated.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Heat Transfer Coefficient at Cast-Mold Interface During Centrifugal Casting: Calculation of Air Gap

During centrifugal casting, the thermal resistance at the cast-mold interface represents a main blockage mechanism for heat transfer. In addition to the refractory coating, an air gap begins to form due to the shrinkage of the casting and the mold expansion, under the continuous influence of strong centrifugal forces. Here, the heat transfer coefficient at the cast-mold interface h has been determined from calculations of the air gap thickness d{sub a} based on a plane stress model taking into account thermoelastic stresses, centrifugal forces, plastic deformations, and a temperature-dependent Young’s modulus. The numerical approach proposed here is rather novel and tries to offer an alternative to the empirical formulas usually used in numerical simulations for a description of a time-dependent heat transfer coefficient h. Several numerical tests were performed for different coating thicknesses d{sub C}, rotation rates Ω, and temperatures of solidus T{sub sol}. Results demonstrated that the scenario at the interface is unique for each set of parameters, hindering the possibility of employing empirical formulas without a preceding experiment being performed. Initial values of h are simply equivalent to the ratio of the coating thermal conductivity and its thickness (~ 1000 Wm{sup −2} K{sup −1}). Later, when the air gap is formed, h drops exponentially to values at least one order of magnitude smaller (~ 100 Wm{sup −2} K{sup −1}).

36 MATERIALS SCIENCE↗
DOE OSTI2023

U-rich U-Mo Solidus, Liquidus, Enthalpy, and Thermal Diffusivity

Several material properties have been studied as a function of composition as part of the USHPRR effort to use U-10Mo for LEU monolithic fuel foils, with special attention to areas where simulation outcomes can be improved. The liquidus and solidus phase boundaries are important for engineering design of processing parameters and for predicting the degree of microsegregation within initial castings. The numerous phase diagram constructions available in the literature differ significantly in their solid/liquid boundary definitions, therefore, an experimental strategy was employed in order to resolve some of the discord. That strategy focuses not on proving any singular point, but instead to provide data with highly characterized uncertainty. The data presented here is the most consistent with the U-rich liquidus and solidus boundaries provided by H. Okamoto (2012), Berche et al. (2011), and Mardon et al. (1959). The recently suggested change in the peritectic reaction temperature (to 1302 K) suggested by Berchè and adopted by Okamoto is also supported, but with lower confidence. The enthalpy of fusion is a basic characteristic of the solidification reaction property for which is required for both research-oriented predictions of behavior and development of applied design strategies for casting engineering. It has been determined that an admixture model for the heat of fusion between U BCC and Mo BCC is a reasonable assumption within the composition region of interest, though limitations of the measurement accuracy impacts the ability to support any trends more detailed than this baseline behavior. A limited number of thermal diffusivity measurements were also performed into the gamma region to provide additional information for solidification modeling and simulations as well as a check on the component properties of thermal conductivity, density, and heat capacity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Two-layer cathode architecture for high-energy density and high-power density solid state batteries

Solid state batteries with high-energy density and high-power density require the development of thick and energy dense cathodes. Structured cathode electrodes with a double-layer configuration were enabled using a freeze tape casting technique. A bottom dense layer was utilized to enhance the energy density whereas a top porous layer with vertically aligned walls was utilized to enhance the power density. The porous structure of the power layer was achieved by ice templating this layer on top of the densified energy layer of the cathode. This configuration was found to better utilize the active material of the cathodes and was optimized using numerical simulation and computer modeling. Cells with Li metal anode and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at approximately 5 and 20 mg/cm 2 were cycled at 70 °C at different C-rates. Poly(ethylene oxide) (PEO) with lithium bis-trifluoromethanesulfonimide (LiTFSI) was used for the catholyte and the solid-state electrolyte. The structured cathodes exhibited more than double capacity values as well as better Coulombic efficiency compared to non-structured (single-layer) thick cathodes. In conclusion, synchrotron X-ray tomography and scanning electron microscopy were used to characterize the microstructure of the cathodes.

25 ENERGY STORAGE↗
DOE OSTI2017

Development of Integrated Die Casting Process for Large Thin-Wall Magnesium Applications

The purpose of this project was to develop a process and product which would utilize magnesium die casting and result in energy savings when compared to the baseline steel product. The specific product chosen was a side door inner panel for a mid-size car. The scope of the project included: re-design of major structural parts of the door, design and build of the tooling required to make the parts, making of parts, assembly of doors, and testing (both physical and simulation) of doors. Additional work was done on alloy development, vacuum die casting, and overcasting, all in order to improve the performance of the doors and reduce cost. The project achieved the following objectives: 1. Demonstrated ability to design a large thin-wall magnesium die casting. 2. Demonstrated ability to manufacture a large thin-wall magnesium die casting in AM60 alloy. 3. Tested via simulations and/or physical tests the mechanical behavior and corrosion behavior of magnesium die castings and/or lightweight experimental automotive side doors which incorporate a large, thin-wall, powder coated, magnesium die casting. Under some load cases, the results revealed cracking of the casting, which can be addressed with re-design and better material models for CAE analysis. No corrosion of the magnesium panel was observed. 4. Using life cycle analysis models, compared the energy consumption and global warming potential of the lightweight door with those of a conventional steel door, both during manufacture and in service. Compared to a steel door, the lightweight door requires more energy to manufacture but less energy during operation (i.e., fuel consumption when driving vehicle). Similarly, compared to a steel door, the lightweight door has higher global warming potential (GWP) during manufacture, but lower GWP during operation. 5. Compared the conventional magnesium die casting process with the “super-vacuum” die casting process. Results achieved with cast tensile bars suggest some improvement in tensile properties with vacuum casting. Plant trials with large castings revealed cavity fill issues attributed to cooling and partial solidification of metal in the shot sleeve while waiting for vacuum to be established in the die cavity. 6. Developed age-hardenable Mg-based alloys as potential alternatives to the AM60 and AZ91 alloys typically used in automotive applications. Mg-7%Al-based alloys having Sn or Sn+Si additions exhibited significant age hardening, but more work is needed to demonstrate significant improvement in tensile properties. Corrosion behavior of these alloys is between those of AM60 and AZ91 alloys. 7. Evaluated the die casting of magnesium directly onto either steel or aluminum tubes as a potential process to make large lightweight subassemblies. Samples were free of gross defects, but additional work is needed to increase the interfacial shear strength. Overall, the project demonstrated that an automotive door-in-white design incorporating a die cast magnesium inner panel and a stamped aluminum outer panel can achieve approximately 50% mass reduction compared to the stamped steel baseline door-in-white. This leads to reduced energy consumption when driving the vehicle, which should more than offset the increased embedded energy of manufacture associated with the lighter metals. However, additional design work would be needed in order to meet the mechanical performance required of a door. Development of high-strength, high-ductility magnesium alloy castings would help make this technology more attractive for potential use in the side doors on automobiles. Also, increased use of recycled magnesium and aluminum would reduce the embedded energy and greenhouse gas emissions associated with the manufacture of this type of lightweight door. Commercialization planning of the type of lightweight door technology addressed in this project would be contingent upon the doors meeting all technical performance requirements of the car maker. The specific lightweight door developed in this project didn’t meet some of those requirements, but a preliminary business case study was conducted anyhow. This study considered the ratio of cost increase to mass decrease when the lightweight door is compared to a baseline steel door. The ratio was found to be in an acceptable range for some vehicle programs, especially if the number of such vehicles to be produced is equal to or slightly less than the estimated 250,000-shot life of the die set. This would allow for the investment in the dies to be spread across many parts and thereby help minimize the cost increase.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2015

Fully coupled simulation of cosmic reionization. I. numerical methods and tests

Here, we describe an extension of the Enzo code to enable fully coupled radiation hydrodynamical simulation of inhomogeneous reionization in large similar to(100 Mpc)(3) cosmological volumes with thousands to millions of point sources. We solve all dynamical, radiative transfer, thermal, and ionization processes self-consistently on the same mesh, as opposed to a postprocessing approach which coarse-grains the radiative transfer. But, we employ a simple subgrid model for star formation which we calibrate to observations. The numerical method presented is a modification of an earlier method presented in Reynolds et al. differing principally in the operator splitting algorithm we use to advance the system of equations. Radiation transport is done in the gray flux-limited diffusion (FLD) approximation, which is solved by implicit time integration split off from the gas energy and ionization equations, which are solved separately. This results in a faster and more robust scheme for cosmological applications compared to the earlier method. The FLD equation is solved using the hypre optimally scalable geometric multigrid solver from LLNL. By treating the ionizing radiation as a grid field as opposed to rays, our method is scalable with respect to the number of ionizing sources, limited only by the parallel scaling properties of the radiation solver. We test the speed and accuracy of our approach on a number of standard verification and validation tests. We show by direct comparison with Enzo's adaptive ray tracing method Moray that the well-known inability of FLD to cast a shadow behind opaque clouds has a minor effect on the evolution of ionized volume and mass fractions in a reionization simulation validation test. Finally, we illustrate an application of our method to the problem of inhomogeneous reionization in a 80 Mpc comoving box resolved with 3200(3) Eulerian grid cells and dark matter particles.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2019

Mathematical Modeling on the Influence of Casting Parameters on Initial Solidification at the Meniscus of Slab Continuous Casting

In the current study, the two-dimensional mold model was applied to investigate the influence of different casting parameters on the initial solidification at the meniscus of the continuous casting mold. The profile of the meniscus and the slag rim, and the heat flux on the hot face of the copper plate, were compared with different locations of the mold and different casting parameters. The depth of the oscillation marks and solidified meniscus through simulation was measured with different casting parameters. With the mold oscillating downward from the peak to the valley, the maximum heat flux on the hot face of the copper plate near the meniscus increased from 4.3 to 5.5 MW/m{sup 2}, the thickness of the slag rim decreased from 4.7 to 4.2 mm, and the height of the curved meniscus also decreased. With the increase of casting speed from 1.2 to 1.45 m/min, the maximum speed of the upper backflow increased from 0.6 to 0.8 m/s, and the lowest location of the meniscus at approximately 310 mm from the copper plate decreased from 22 to 12 mm below the meniscus near the nozzle, where the slag entrapment easily occurred. With the increase of the casting speed, casting superheat, and oscillation frequency, and the decrease of the water flow rate in the mold and oscillation amplitude, the thickness of the slag rim decreased. With the increase of casting speed and superheat, and the decrease of the water flow rate in the mold, oscillation frequency, and oscillation amplitude, the depth of the solidified meniscus decreased. The regression equation was fitted to estimate the depth of hooks at the subsurface of slabs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Simple, Scalable Large Deformation Solid Mechanics Implementation in the MOOSE Framework

This article describes a large deformation solid mechanics solver implemented as part of the freely available and open source MOOSE finite element simulation framework. The article documents the choices made in developing the solid mechanics framework and describes novel formulations for the gradient operator and constitutive modeling framework made to simplify implementations of different coordinate systems, stabilized gradient operators, and different constitutive model inputs and outputs. In the process, the article describes a new formulation that casts objective integration of the Cauchy stress as a linear transformation of the small stress rate. Finally, the article presents key implementation details and examines the parallel efficiency of the solid mechanics solver implemented in MOOSE. The implementation retains a good weak scaling efficiency beyond 1,000 parallel processes. The article includes a discussion of the factors limiting the parallel efficiency of implicit, large deformation solid mechanics codes on current high-performance computers, with the main current limitation being the scalability of the algebraic multigrid methods used to solve the linearized equilibrium equations.

Applied computing → Computer-aided design↗
DOE OSTI2019

Manufacture of Wear-Resistant Cast-Iron Grinding Balls without Shrinkage Defects

A manufacturing technology has been developed for wear-resistant cast-iron grinding balls without shrinkage defects. In this method, the balls are cast in single-use sand–clay molds. A new approach to designing the casting system is developed. By numerical modeling, the time dependence of solidification is derived. As a trial, grinding balls are produced by the proposed technology.

42 ENGINEERING↗
DOE OSTI2020

Model-based Reconstruction for Single Particle Cryo-Electron Microscopy

Single particle cryo-electron microscopy is a vital tool for 3D characterization of protein structures. A typical workflow involves acquiring projection images of a collection of randomly oriented particles, picking and classifying individual particle projections by orientation, and finally using the individual particle projections to reconstruct a 3D map of the electron density profile. The reconstruction is challenging because of the low signal-to-noise ratio of the data, the unknown orientation of the particles, and the sparsity of data especially when dealing with flexible proteins where there may not be sufficient data corresponding to each class to obtain an accurate reconstruction using standard algorithms. In this paper we present a model-based image reconstruction technique that uses a regularized cost function to reconstruct the 3D density map by assuming known orientations for the particles. Our method casts the reconstruction as minimizing a cost function involving a novel forward model term that accounts for the contrast transfer function of the microscope, the orientation of the particles and the center of rotation offsets. We combine the forward model term with a regularizer that enforces desirable properties in the volume to be reconstructed. Using simulated data, we demonstrate how our method can significantly improve upon the typically used approach.

Venkatakrishnan, Singanallur↗
DOE OSTI2018

Carbide Particle Redistribution in U10Mo Alloy during Hot Rolling Process

The influence of initial carbide particle distribution features on the evolution of particle and stringer distribution within U10Mo alloy during hot rolling was investigated in this study. This work will provide guidance to casting optimization work and identify actionable process changes to eliminate the surface features directly attributed to carbides. Various synthetic microstructure-based finite-element (FE) models were generated with consideration of different parameters (i.e., particle shape, particle volume fraction and particle distribution). Plane-strain compression loading was employed in the FE models to simulate hot rolling to 40% and 80% reductions. Stringer statistics analyses and two-point correlation functions were then performed with the simulated hot-rolling results. The results from stringer analyses show that stringer volume fraction substantially increases with increased rolling reduction for microstructure with particles distributed along grain boundaries, and that microstructures with elliptical particles may have slightly higher stringer volume fractions than those with circular particles. The results also show that the maximum stringer length can increase substantially with increased rolling reduction for microstructures with elliptical particles along grain boundaries, and that the microstructures with higher-aspect-ratio elliptical particles may have higher stringer volume fraction and higher maximum stringer length. Near-surface numbers of particles and particle volume fractions also increase with increased rolling reduction. The results from application of the two-point correlation function show that the particle shape (i.e., circular or elliptical) may not have significant influence on the overall shapes of the correlation curves, and that the correlation curves tend to show higher peaks at short distance and then gradually decrease for microstructures with higher particle volume fractions and particles distributed along grain boundaries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Field-Scale Lysimeter Studies of Glass and Cementitious Waste Forms at the Hanford Site - 20392

The Hanford site Integrated Disposal Facility (IDF) will receive waste forms from vitrification activities at the Hanford Waste Treatment and Immobilization Plant (WTP). The waste form inventory to be disposed of at the IDF will consist of vitrified low-activity waste (LAW) in glass forms and solidified (or encapsulated) secondary wastes in cementitious forms. The IDF is a near-surface burial facility located near Hanford's Waste Treatment and Immobilization Plant in the 200 East Area of the site's Central Plateau. An extensive set of laboratory experimental data has been collected to support IDF performance assessment calculations of the eventual degradation of waste forms and mobility of contaminants. This paper describes the start of a field experiment to generate waste-form performance data on a larger scale (tens of centimeters), over a longer duration (five years or more), and under field conditions representative of the IDF. Results from this study are expected to improve model descriptions of contaminant mobility, reduce uncertainties about the representativeness of laboratory results in the IDF performance assessment, improve stakeholder confidence in the safe disposal of treated waste at the IDF, and facilitate the adoption of informed facility designs with the potential to reduce operational costs. A lysimeter test facility near Hanford's 200 West Area has been repurposed to carry out long-term assessments of waste forms buried in sediments excavated from the IDF. The waste forms are buried in large drainage lysimeters, open caissons that are two meters in diameter and three meters deep. Waste forms are buried in up to six locations in each lysimeter. Samplers collect pore water and drainage water beneath the waste forms and air from the pore space adjacent to waste forms. Sensors measure temperature, soil water content, soil water tension, and drainage flux. One lysimeter containing cementitious waste forms and one containing glass waste forms have been completed, along with a control lysimeter (without waste forms). The cementitious waste forms are Cast Stone grout formulations using a liquid secondary waste simulant and a generic Hanford high-salt simulant, as well as a hydrated lime-based grout formulation using a liquid secondary waste simulant. Technetium-99 and iodine-127 were added as tracers to monitor contaminant mobility. Glass waste forms were fabricated in two formulations (LAWA44 and ORLEC28), with rhenium and molybdenum tracers to monitor waste form degradation. The predicted performance of the waste forms in the lysimeters was modeled prior to installation to determine waste form size, tracer concentration/activity, and locations of sensors and samplers. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Computational Design of a Simple Flyer Plate Launcher

The response of materials to shock loading is important to understand for a variety of applications. When shock physics emerged during and after WWII, direct explosive loading or explosively driven plate impact was the primary tool for these studies. Subsequent decades have seen the widespread use of large caliber guns for plate impact studies, laser-shock facilities and pulsed power facilities. INL currently lacks a gun suitable for plate impact or explosives casting and machining facilities; however, it does possess explosives use and handling capabilities. An option for performing plate impact experiments was needed, therefore continuum scale models were utilized to explore a few simple donor-acceptor explosive plane wave lens designs, one of which could be hand packed with plastic explosives to launch flyer plates. 2D simulations were performed to study different geometries in an effort to minimize the difference in shock arrival across the central portion of a small copper flyer plate. A shock wave arrival time difference under 50 ns across 50 percent of the center of the flyer was achieved with a few designs. This work summarizes the computational models and results.

36 MATERIALS SCIENCE↗