Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Calvin cycle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Intra-catalyst CH 4 oxidation pathways on a Pd/Al 2 O 3 /CeZrO x -based commercial catalyst and implications on NO x conversion profiles for a natural gas vehicle exhaust under lambda modulation

The performance of a three-way catalyst (TWC) in natural gas-powered vehicles is enhanced by periodic changes in air-to-fuel ratio (λ-modulation). The reaction networks and sequences inside the catalyst that facilitate such enhanced performance have not been extensively investigated. Here, this work applied intra-catalyst measurements (SpaciMS) to analyze the transient spatiotemporal gas concentrations inside a Pd-based TWC to establish relationships between CH 4 , NO x , CO and H 2 conversion pathways. Steam reforming and partial oxidation were revealed to be the main CH 4 conversion routes. The cyclic rich-lean conditions combined with the oxygen storage capacity (OSC) of the TWC generate reduced and oxidized zones that are constantly moving within the catalyst, changing the dominant chemical reactions occurring on the surface. In the reduced zones, OSC is depleted while CH 4 is converted through steam reforming and NO x is converted through reactions with H 2 , CO, and other surface-bound reducing fragments formed by CH 4 conversion. In the oxidized zones, OSC is replenished, CH 4 is converted by partial oxidation, and H 2 , CO, and NH 3 are oxidized. The length of lean-rich phases impacts the catalyst performance significantly; too short or too long of a rich or lean phase can lower the overall conversion of reactive species. An inhibition of CH 4 conversion was observed during the rich phase possibly due to CO-poisoning of active sites. The intra-catalyst measurements revealed that the catalyst consists of three distinct reaction zones and their lengths vary with modulation conditions. Various modulation frequencies, amplitudes, λ-centers, and temperatures were investigated which allowed an understanding of how these parameters affect the reaction zones and catalyst utilization. Understandings from this work can enable adaptive λ-control strategies to optimize the overall TWC performance over a range of vehicle operating conditions.

Lean-Rich cycling↗

Warm Water Oxidation Verification – Scoping and Stirred Reactor Tests

Scoping tests to evaluate the effects of agitation and pH adjustment on simulant sludge agglomeration and uranium metal oxidation at ~95°C were performed under Test Instructions(a,b) and as per sections 5.1 and 5.2 of this Test Plan prepared by AREVA. (c) The thermal testing occurred during the week of October 4-9, 2010. The results are reported here. For this testing, two uranium-containing simulant sludge types were evaluated: (1) a full uranium-containing K West (KW) container sludge simulant consisting of nine predominant sludge components; (2) a 50:50 uranium-mole basis mixture of uraninite [U(IV)] and metaschoepite [U(VI)]. This scoping study was conducted in support of the Sludge Treatment Project (STP) Phase 2 technology evaluation for the treatment and packaging of K-Basin sludge. The STP is managed by CH2M Hill Plateau Remediation Company (CHPRC) for the U.S. Department of Energy. Warm water (~95°C) oxidation of sludge, followed by immobilization, has been proposed by AREVA and is one of the alternative flowsheets being considered to convert uranium metal to UO 2 and eliminate H 2 generation during final sludge disposition. Preliminary assessments of warm water oxidation have been conducted, and several issues have been identified that can best be evaluated through laboratory testing. The scoping evaluation documented here was specifically focused on the issue of the potential formation of high strength sludge agglomerates at the proposed 95°C process operating temperature. Prior hydrothermal tests conducted at 185°C produced significant physiochemical changes to genuine sludge, including the formation of monolithic concretions/agglomerates that exhibited shear strengths in excess of 100 kPa (Delegard et al. 2007).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Literature Review: Crud Formation at the Liquid/Liquid Interface of TBP-Based Solvent-Extraction Processes

This report summarizes the literature reviewed on crud formation at the liquid:liquid interface of solvent extraction processes. The review is focused both on classic PUREX extraction for industrial reprocessing, especially as practiced at the Hanford Site, and for those steps specific to plutonium purification that were used at the Plutonium Reclamation Facility (PRF) within the Plutonium Finishing Plant (PFP) at the Hanford Site.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Scoping Study for Fast Flux Testing in the Advanced Test Reactor

The value of fast spectrum reactors remains prominent in the nuclear technology portfolio. The performance of these reactors can be maximized with advancements in nuclear fuel technologies, but development of these technologies is currently held back by lack of fast spectrum test reactors available to the United States. Spectral modification of experiment positions in the thermal spectrum Advanced Test Reactor (ATR) has long been used to support fast reactor fuel development, but these methods have not been progressed to their full potential. This study investigated the use of concentric rings of aluminum-clad fuel plates in ATR flux traps and thermal neutron absorbing filters to increase fast neutron flux on test specimens. This concept was termed the Boosted Energy Advanced Spectrum Test (BEAST). This approach will enable irradiation of advanced fuel designs in prototypic-length fuel pins and representative flux environment to support post irradiation exams, enable transient testing, and produce the type of data that will permit lead test assembly irradiations in true Sodium Fast Reactors (SFRs) when they become available. Neutronic predictions were performed to investigate BEAST design options and thermal hydraulic models were produced to ensure feasibility of BEAST. Two versions were considered based on the geometric limitations of ATR’s small and large flux traps. The small version was found to be preferable due to slightly higher fast flux and fast-to-thermal neutron ratio. Perhaps more influentially, the small flux trap option was also preferred to avoid conflict with ongoing very high temperature reactor fuel irradiation programs in ATR’s large northeast flux trap. The small flux trap option provided less than half the test volume of the large version, but still had adequate volume for seven SFR pins in cross section which could be stacked two-high in ATR’s 1.2m long core to accommodate up to 14 EBR-II size pins. The preference for the small flux trap configuration should be revisited if additional collaborative test programs emerge with the need to irradiate a significant volume of additional specimens. Calculations were performed regarding a lithium deuteride ring to convert thermal neutrons into 14 MeV fusion neutrons. At the time this report was written these calculations were partially complete and it remains to be seen whether the concept would be worth including in BEAST. Given the preference for the small flux trap option, which does not afford enough room for the 14 MeV ring, it was concluded to defer future work on the lithium deuteride ring. This decision could be revisited if fusion material research programs emerge for collaborative testing in BEAST. A cadmium-lined specimen holder design was found to be adequate in filtering thermal neutrons and preferred over other neutron absorbers based on past experience with cadmium baskets. It was acknowledged that cadmium-bearing hardware would become depleted and need to be replaced occasionally, which appeared feasible from a mechanical design perspective. Neutronic studies investigated different enrichment levels in the booster fuel using uranium-molybdenum alloy dispersion fuel which has performed well in past ATR irradiations. Both options were able to drive fuel pins to SFR-like fission heating rates. The high enriched booster fuel option outperformed the low enriched option by ~20% on key metrics including fast flux and fast-to-thermal ratio, but the low enriched option was favored in order to broaden options for potential fuel suppliers. The preferred BEAST design options including cadmium filter with low enriched booster fuel in the small flux trap configuration was predicted to achieve 6.2E14 n/cm2sec fast flux (>0.1 MeV) with a fast-to-thermal ratio of 44.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal Barrier Coatings Overview: Design, Manufacturing, and Applications in High-Temperature Industries

Today’s competitive world economy is creating an indispensable demand for increased efficiency of engineering components that operate in harsh environments (i.e., very high-temperature, corrosive, or neutron irradiation environments), for applications in the energy, automotive, aerospace, electronics, and power industries. Increased research is being done on thermal barrier coatings (TBCs) for protecting such components, since the versatility of manufacturing techniques and the scale of deployment result in increased life, economics, performance, and durability. This review focuses on the advances that led to using TBCs for component life extension and, more recently, as an integral part of advanced component design for high-temperature and other types of harsh environments, such as those found in nuclear-related applications. Furthermore, factors that led to state-of-the-art advanced coating-fabrication techniques [e.g., electron-beam physical vapor deposition (EB-PVD), plasma spray deposition, and electrophoretically deposited TBCs, as well as functionally graded material (FGM) manufacturing] have also been emphasized in current coating R&D. This review explores the current state of TBCs, i.e., the latest advances regarding their fabrication and performance, associated challenges, and recommendations for their future use in aerospace, nuclear, high-temperature, or otherwise harsh environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mitigation of Hydrogen Gas Generation from the Reaction of Water with Uranium Metal in K Basins Sludge

Means to decrease the rate of hydrogen gas generation from the chemical reaction of uranium metal with water were identified by surveying the technical literature. The underlying chemistry and potential side reactions were explored by conducting 61 principal experiments. Several methods achieved significant hydrogen gas generation rate mitigation. Gas-generating side reactions from interactions of organics or sludge constituents with mitigating agents were observed. Further testing is recommended to develop deeper knowledge of the underlying chemistry and to advance the technology aturation level. Uranium metal reacts with water in K Basin sludge to form uranium hydride (UH3), uranium dioxide or uraninite (UO2), and diatomic hydrogen (H2). Mechanistic studies show that hydrogen radicals (H·) and UH3 serve as intermediates in the reaction of uranium metal with water to produce H2 and UO2. Because H2 is flammable, its release into the gas phase above K Basin sludge during sludge storage, processing, immobilization, shipment, and disposal is a concern to the safety of those operations. Findings from the technical literature and from experimental investigations with simple chemical systems (including uranium metal in water), in the presence of individual sludge simulant components, with complete sludge simulants, and with actual K Basin sludge are presented in this report. Based on the literature review and intermediate lab test results, sodium nitrate, sodium nitrite, Nochar Acid Bond N960, disodium hydrogen phosphate, and hexavalent uranium [U(VI)] were tested for their effects in decreasing the rate of hydrogen generation from the reaction of uranium metal with water. Nitrate and nitrite each were effective, decreasing hydrogen generation rates in actual sludge by factors of about 100 to 1000 when used at 0.5 molar (M) concentrations. Higher attenuation factors were achieved in tests with aqueous solutions alone. Nochar N960, a water sorbent, decreased hydrogen generation by no more than a factor of three while disodium phosphate increased the corrosion and hydrogen generation rates slightly. U(VI) showed some promise in attenuating hydrogen but only initial testing was completed. Uranium metal corrosion rates also were measured. Under many conditions showing high hydrogen gas attenuation, uranium metal continued to corrode at rates approaching those observed without additives. This combination of high hydrogen attenuation with relatively unabated uranium metal corrosion is significant as it provides a means to eliminate uranium metal by its corrosion in water without the accompanying hazards otherwise presented by hydrogen generation.

08 HYDROGEN↗

Design and Fabrication of a Temperature-Controlled Fueled Molten Salt Capsule Irradiation Experiment

Idaho National Laboratory (INL) is developing a Molten salt Research Temperature-controlled Irradiation (MRTI) experimental capsule for the Neutron Radiography (NRAD) reactor. The experiment is envisaged to be versatile and able to host a variety of salt-wall material combinations. The first test is designed to contain actinide-bearing chloride salt, which previously has not been subjected to a neutron field. The main objectives of the experiment are to produce irradiated salt samples for Post Irradiation Examination (PIE), to evaluate salt behavior under irradiation, and to test in-situ sensors/instrumentation. The final design for the experiment completed in 2022, and fabrication of the experiment is underway. The salt is double encapsulated providing insulation and redundancy in the case of leakage. A gas-gap between the inner capsule and the outer container enables tuning of thermal conduction to the NRAD coolant by altering its thickness and its gas-mixture. An inert gas mixture ratio in the gas-gap ensures the configurations reached a targeted average salt temperature of 600oC, while avoiding salt freezing or exceeding material limits. A resistive heater placed within a thermowell and controls the temperature of the experiment (both when the reactor is on or off). The selected configurations can contain over 10 cm3 of fuel-bearing chloride salt, which is sufficient for the purposes of the post-irradiation examination (PIE) and provides sufficient volume for two submerged thermocouple probes to monitor salt temperature. The capsule wall material is Inconel 625, and weld qualifications for the assembly have been developed. A glove-box laser weld technique was refined as part of this process to ensure a leak-tight assembly for the salt-bearing assembly and reduce the risks of impurities permeating into the salt. This work was supported through the INL Laboratory Directed Research & Development (LDRD) Program under DOE Idaho Operations Office Contract DE-AC07-05ID14517.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

International organization for standardization on the topic of nuclear criticality safety (ISO TC85/SC5/WG8) - 14244

This paper is a four-year update (i.e. 2011 - 2015) about the progress and activities of the International Organization for Standardization (ISO), Technical Committee 85 (TC85) on Nuclear energy, Subcommittee 5 (SC5) on Nuclear fuel cycle, Working Group 8 (WG8) on Nuclear criticality safety. The update provides a brief summary of historic standards developed by ISO TC85/SC5/WG8 and descriptions about evolving standards for nuclear criticality safety. The update describes the potential value and relevance of indigenous standards and technological developments by OECD regarding nuclear criticality safety standards. Elements of the published WG8 ISO standards that have been incorporated into International Atomic Energy Agency non-consensus guides and standards are provided. A review of international participation and needed participation is also addressed along with the benefits to ISO participating member countries. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Magnesium Todorokite: Influence of Morphology on Electrochemistry in Lithium, Sodium and Magnesium Based Batteries

Samples of Mg-todorokite with mixed nanosheet & nanowire (referred to as nanosheets for the sake of simplicity) and pure nanowire morphology were prepared to probe the morphological impact on battery relevant electrochemistry. The samples had similar physicochemical properties where the Mg-todorokite nanosheets had a composition of Mg 0.20 MnO 2 with a crystallite size of 9 nm and water content of 0.29 moles of H 2 O per formula unit, while the nanowires had a composition of Mg 0.19 MnO 2 with a crystallite size of 14 nm and water content of 0.28. The electrochemistry of the Mg-todorokite materials was evaluated using cyclic voltammetry, galvanostatic cycling, and rate capability testing. The Mg-todorokite nanosheets showed higher discharge capacity than the nanowires in lithium, sodium and magnesium-based electrolytes. Notably, the nanowire materials exhibited excellent cycling stability compared to the nanosheets in lithium and sodium-based batteries. Finally, x-ray absorption spectroscopy (XAS) of lithiated samples suggests that Mn in the nanosheet containing material was more highly reduced to Mn 3+ after the 1st full discharge explaining the higher initial capacities observed. However, a MnO-like structural distortion was observed after extended cycling in the nanosheet material consistent with its poorer capacity retention.

25 ENERGY STORAGE↗

Strength Measurements of Archive K Basin Sludge Using a Soil Penetrometer

Spent fuel radioactive sludge present in the K East and K West spent nuclear fuel storage basins now resides in the KW Basin in six large underwater engineered containers. The sludge will be dispositioned in two phases under the Sludge Treatment Project: (1) hydraulic retrieval into sludge transport and storage containers (STSCs) and transport to interim storage in Central Plateau and (2) retrieval from the STSCs, treatment, and packaging for shipment to the Waste Isolation Pilot Plant. In the years the STSCs are stored, sludge strength is expected to increase through chemical reaction, intergrowth of sludge crystals, and compaction and dewatering by settling. Increased sludge strength can impact the type and operation of the retrieval equipment needed prior to final sludge treatment and packaging. It is important to determine whether water jetting, planned for sludge retrieval from STSCs, will be effective. Shear strength is a property known to correlate with the effectiveness of water jetting. Accordingly, the unconfined compressive strengths (UCS) of archive K Basin sludge samples and sludge blends were measured using a pocket penetrometer modified for hot cell use. Based on known correlations, UCS values can be converted to shear strengths. Twenty-six sludge samples, stored in hot cells for a number of years since last being disturbed, were identified as potential candidates for UCS measurement and valid UCS measurements were made for twelve, each of which was found as moist or water-immersed solids at least 1/2-inch deep. Ten of the twelve samples were relatively weak, having consistencies described as 'very soft' to 'soft'. Two of the twelve samples, KE Pit and KC-4 P250, were strong with 'very stiff' and 'stiff' consistencies described, respectively, as 'can be indented by a thumb nail' or 'can be indented by thumb'. Both of these sludge samples are composites collected from KE Basin floor and Weasel Pit locations. Despite both strong sludges having relatively high iron concentrations, attribution of their high strengths to this factor could not be made with confidence as other measured sludge samples, also from the KE Basin floor and of high iron concentration, were relatively weak. The observed UCS and shear strengths for the two strong sludges were greater than observed in any prior testing of K Basin sludge except for sludge processed at 185 C under hydrothermal conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ZEUS Activation Foils Report for Experiments 1-5

The ZEUS experiments were conducted using the COMET vertical assembly machine at the Los Alamos Critical Experiments Facility (LACEF) at the Los Alamos National Laboratory (LANL). The experiments were designed to check the adequacy of cross sections in the intermediate-energy range. For the first four experiments, 12 kg highly enriched uranium (HEU) layers were sandwiched between different numbers of graphite plates in a vertical stack. In the first four experiments, a unit cell consisted of n graphite plates, an HEU layer, and then another n graphite plates. The unit cells were stacked until criticality was obtained. Experiments 1, 2, 3, and 4 contained decreasing amounts of graphite, where the unit cells value n was 4, 3, 2 and 1 respectively. In experiment 5 the HEU plates were in direct contact with each other to evaluate cross sections in the fast-energy range. A detailed description of experiments 1-4 is provided in reference, and of experiment 5, in reference. In order to investigate the cross sections in more detail, some ZEUS runs were made with activation foils inside the assemblies. Ratios of the activations of various foils are a standard method of measuring the gross neutron spectrum shape. A more detailed spectrum can be determined by simultaneously unfolding the response of several foils. This report describes the unfolding of the ZEUS activation foils data. The focus in this analysis is on the fast-energy range, especially at > 5 MeV.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

M&C 2025: Application of Fuel Depletion Chain Simplification to Experiment Analysis in the Advanced Test Reactor

Irradiation experiment analysis can be informed by high-fidelity reactor engineering depletion results, but it comes at a computational cost. Applying depletion chain simplification to the Advanced Test Reactor driver fuel before performing experiment depletions permits their programmatic parameters to be calculated faster, with a small penalty to accuracy. This work contrasts the results of two irradiation experiments with different neutronic characteristics and provides general recommendations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fast neutron irradiation capability in existing thermal test reactors

In today’s nuclear industry, momentum towards the design, licensing, and construction of advanced nuclear demonstration plants, including fast reactors, is at a remarkably high level. However, there are currently no dedicated fast spectrum irradiation test facilities in the United States to support the development of fast spectrum technologies. As a result, a unique situation is developing where most of these plants will likely be designed by leveraging historic nuclear material technologies, but where the further optimization and advancement is impeded by the lack of fast neutron irradiation test facilities. While these circumstances present a challenge, there are some near-term opportunities that, if seized, can still help develop advanced fast reactor materials to a meaningful level of readiness to support future commercial fast reactors. Here, in this paper, we assess the feasibility of using thermal neutron filtering materials in existing experiment positions in the Advanced Test Reactor (ATR) at Idaho National Laboratory and the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory to simulate fast reactor test environments for nonfuel test specimens. Items investigated include the incident neutron flux (both fast and thermal), the total neutron fluence and cumulative atom displacements, helium production rate due to thermal neutron capture in nickel, and the potential impact that the thermal neutron filter material has on the cycle length of a given reactor. It is concluded that while HFIR provides the highest fast flux of all the options investigated, it is limited in the amount of thermal neutron filtering material that can be introduced into an experiment position without significantly affecting the operation of the reactor. Irradiation in Outboard-A positions in the ATR was found to be the most realistic near-term experiment avenue due to having ample space for several capsules in a moderately fast flux.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗