Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION EFFICIENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Emissions of oxides of nitrogen from an experimental premixed-hydrogen burner

Flame-tube experiments using premixed hydrogen and air were conducted to determine the emissions of oxides of nitrogen (NOx) resulting from ultralean combustion. Measurements of NOx emissions and combustion efficiency were made for inlet mixture temperatures of 600 and 700 K, pressures of 3.8 x 10 to the 5th power and 5.2 x 10 to the 5th power N/m squared, reference velocities of 15 to 18 m/sec, and equivalence ratios of 0.2 to 0.4. At the 700 K inlet mixture temperature, NOx emissions were 0.06 ppmv, and combustion efficiency was 98 percent at an equivalence ratio of 0.24. The use of a high-blockage (92-percent blockage) flameholder made it possible to conduct tests without upstream burning in the premixing duct for mixtures with equivalence ratios less than 0.4. For richer mixtures upstream burning did occur and prevented further testing.

Anderson, D. N.↗
NASA NTRS1977

Effect of fuel properties on performance of single aircraft turbojet combustor at simulated idle, cruise, and takeoff conditions

The performance of a single-can JT8D combustor was investigated with a number of fuels exhibiting wide variations in chemical composition and volatility. Performance parameters investigated were combustion efficiency, emissions of CO, unburned hydrocarbons and nitrogen oxides, as well as liner temperatures and smoke. The most pronounced effects of changes in fuel composition were observed at simulated cruise and takeoff conditions where smoke and liner temperatures increased significantly as the hydrogen content of the fuel decreased. At the simulated idle condition, emissions of CO and unburned hydrocarbons increased slightly and, accordingly, combustion efficiencies decreased slightly as the hydrogen content of the fuels decreased.

Butze, H. F.↗
NASA NTRS1948

Simulated Altitude Performance of Combustors for the Westinghouse 24C Jet Engine I-24C-2 Combustor

A Westinghouse 24C-2 combustor was investigated at conditions simulating operation of the 24C Jet engine at zero ram over ranges of altitude and engine speed. The investigation was conducted to determine the altitude operational limits, that is, the maximum altitude for various engine speeds at which an average combustor-outlet gas temperature sufficient for operation of the jet engine could be obtained. Information was also obtained regarding the character of the flames, the combustion efficiency, the combustor-outlet gas temperature and velocity distributions, the extent of afterburning, the flow characteristics of the fuel manifolds, the combustor inlet-to-outlet total-pressure drop, and the durability of the combustor basket. The results of the investigation indicated that the altitude operational limits for zero ram decreased from 12,000 feet at an engine speed of 4000 rpm to a minimum of 9000 feet at 6000 rpm, and thence increased to 49,000 feet at 12,000 rpm.. At altitudes below the operational limits, flames were essentially steady, but, at altitudes above the operational limits, flames were often cycling and either blew out or caused violent explosions and vibrations. At conditions on the altitude operational limits the type of combustion varied from steady to cycling with increasing fuel-air ratio and the reverse occurred with decreasing fuel-air ratio. In the region of operation investigated, the combustion efficiency ranged from 75 to 95 percent at altitudes below the operational limits and dropped to 55 percent or less at some altitudes above the operational limits. The deviations in the local combustor-outlet gas temperatures were within +20 to -30 percent of the mean combustor temperature rise for inlet-air temperatures at the low end of the range investigated, but became more uneven (up to +/-100 percent) with increasing inlet-air temperatures. The distribution of the combustor-outlet gas velocity followed a similar trend. Practically no afterburning downstream of the combustor outlet occurred. At conditions of high inlet-air temperature several factors indicated that fuel vapor or air formed in the fuel manifolds and adversely affected combustion. The combustor inlet-to-outlet total-pressure drop can be correlated as a function of the ratio of the combustion-air inlet density to outlet density and of the inlet dynamic pressure. The walls of the combustor basket were warped and burned during 29 hours of operation.

Manganiello, Eugene J.↗
NASA NTRS1959

Exploratory Investigation of Aerodynamic Flameholders for Afterburner Application

An investigation was conducted to determine the flameholding capabilities of aerodynamic jets at afterburner operating conditions. Stability data for a number of aerodynamic flameholders were obtained in a 5- by 5-inch test section at inlet-air reference velocities up to 600 feet per second, an inlet-air temperature of 1250 F, and a combustor-inlet pressure of 15 inches of mercury absolute. Combustion efficiency and stability data of the more promising combinations were then obtained in a 10- by 12-inch test section at the same test conditions. Both air and stoichiometric mixtures of fuel and air were used in the jets; mixture flow rates were approximately 1 percent by weight of the total air-flow rate. Injection pressures were limited to values that might be available from compressor-bleed air. At a reference velocity of 600 feet per second, aerodynamic flame-holders alone were unable to maintain a stable flame at injection pressures up to 70 pounds per square inches large reductions in velocity were required to achieve flame stabilization. When the aerodynamic jets were used in combination with a V-gutter flameholder with approximately a 30 percent blocked area, flame stabilization was attained at a velocity of 600 feet per second; however, the combustion efficiencies of the various combinations were no greater than that obtained with the V-gutter alone.

Butze, Helmut F.↗
NASA NTRS1948

Simulated Altitude Performance of Combustors for the 24C Turbojet Engine. III - Performance of Rectangular-Slot Baskets: Performance of Rectangular-Slot Baskets - 3

The performance of an annular combustion chamber from a 24C turbojet engine was investigated over a range of simulated altitudes from 20,000 to 55,000 feet and corrected engine rotor speeds from 6000 to 13,000 rpm at a simulated ram-pressure ratio of 1.04. The purpose of the investigation was to determine the effects on the altitude operational limits, combustor-outlet gas temperature distribution, combustion efficiencies, and combustor inlet-to-outlet total-pressure drops of two changes in the 24C-4B basket air-passage arrangements that were designed to improve combustor-outlet temperature distribution. These changes were: (a) replacement of the downstream secondary air holes with large rectangular slots further upstream (rectangular-slot basket), and (b) enlargement of anticoking holes in the rectangular-slot basket (modified rectangular-slot basket). The results indicate that improved outlet-gas temperature distribution of each succeeding combustor basket investigated was attained at a sacrifice in the altitude limit of operation. The altitude limits of operation of the combustor with the original basket ranged from 34,000 feet at a corrected engine speed of 6000 rpm to a maximum of 52,000 feet at 12 ' 500 rpm. The altitude limits of the rectangular-slot basket were about 2000 feet lower throughout the engine speed range than those of the original basket. The altitude limits of the combustor with the modified rectangular-slot basket were about equivalent to those of the other baskets in the corrected-engine-speed range from 12,000 to 12,500 rpm but were about 10,000 feet lower than those of the original basket in the corrected-engine-speed range from 6000 to 9000 rpm. For the same inlet-air conditions, the combustion efficiencies were highest for the original basket and progressively lower for each of the other two baskets. The combustor inlet-to-outlet pressure drops of all three combustor baskets at the same operating conditions were within +/- 10 percent of the pressure drop of the original basket.

Tischler, Adelbert O.↗
NASA NTRS1993

Test results from a simple, low-cost, pressure-fed liquid hydrogen/liquid oxygen rocket combustor

A simple, low-cost rocket engine was designed, fabricated, and successfully hot fire tested over a wide range of interface conditions and operating parameters. The engine used low enthalpy hydrogen (45 to 70 R, 200 to 390 psia) and oxygen (139 to 163 R, 210 to 480 psia) propellants pressure-fed directly from facility cryogenic tanks. The engine demonstrated excellent performance, with 97% average combustion efficiency, and absence of combustion instabilities. Engine design chamber pressure was 300 psia, yielding about 16,500 pounds thrust at sea level with a 3:1 expansion ration test nozzle. The engine used a fixed-element injector based on TRW's unique coaxial pintle design, but was operated at 60%, 80%, and 100% thrust levels by throttling facility propellant valves. The engine was tested at propellant mixture ratios (O/F) from 5.8 to 8.4; design O/F was 6.6. To document combustion stability, in five tests RDX explosive pulse guns were detonated in radial and tangential directions across the combustion chamber during steady-state operation. The largest disturbance consisted of simultaneous detonation of a 20-grain radial gun and a 40-grain tangential gun. In no case was an instability, either feed system mode or chamber acoustic mode, excited. High-frequency piezoelectric pressure transducers documented stable recovery from disturbance overpressures within 40 milliseconds of peak pressure. A total of 67 firing tests, accumulating 149 seconds of firing time above 10% P(sub c), were performed. Since parametric testing required run durations of only 2 to 3 seconds, a heat sink combustion chamber was employed for most runs. To evaluate the feasibility of a low-cost ablative system for a flight engine design, one 20-second continuous firing was conducted with a silicone rubber chamber/throat/nozzle liner cast in one piece directly into the engine. The ablative engine operated at the equivalent of 309 seconds sea level specific impulse, when adjusted to a 98% efficient 6:1 expansion ration nozzle, and 430 seconds vacuum specific impulse, when adjusted to a 98% efficient 50:1 expansion ratio nozzle. This engine and test series represent an initial subscale demonstration of a new booster-class engine that eliminates the cost and complexity associated with regenerative cooling and typical engine cycles. This paper presents a description of the engine design and discussion and summary data plots of the performance measured during the parametric testing.

Dressler, G. A.↗
NASA NTRS2016

Alternative Bio-Derived JP-8 Class Fuel and JP-8 Fuel: Flame Tube Combustor Test Results Compared using a GE TAPS Injector Configuration

This paper presents results from tests in a flame tube facility, where a bio-derived alternate fuel was compared with JP-8 for emissions and general combustion performance. A research version of General Electric Aviation (GE) TAPS injector was used for the tests. Results include combustion efficiency from gaseous emission measurements, 2D planar laser-based imaging as well as basic flow visualization of the flame. Four inlet test conditions were selected that simulate various engine power conditions relevant to NASA Fundamental Aeronautics Supersonics Project and Environmentally Responsible Aviation Program. One inlet condition was a pilot-only test point. The other three inlet conditions incorporated fuel staging via a split between the pilot and main circuits of either 10%/90% or 20%/80%. For each engine power condition, three fuel mixes were used: 100% JP-8; 100% alternative; and a blend of the two, containing 75% alternative. Results for the inlet cases that have fuel split between pilot and main, indicate that fuel from the pilot appears to be evaporated by the time it reaches the dome exit. Main circuit liquid evaporates within a downstream distance equal to annulus height, no matter the fuel. Some fuel fluorescence images for a 10%/90% fuel staging case show a distinct difference between JP-8 and bio-derived fuel. OH PLIF results indicate that OH forms in a region more centrally-located for the JP-8 case downstream of the pilot, in its central recirculation region (CRZ). For the bio-derived Hydrotreated Renewable Jet (HRJ) fuel, however, we do not see much OH in the CRZ. The OH image structure near the dome exit is similar for the two fuels, but farther downstream the OH in the CRZ is much more apparent for the JP-8 than for the alternate fuel. For all conditions, there was no discernable difference between fuel types in combustion efficiency or emissions.

gas turbine combustors↗
NASA NTRS1947

Effect of combustor-inlet conditions on performance of an annular turbojet combustor

The combustion performance, and particularly the phenomenon of altitude operational limits, was studied by operating the annular combustor of a turbojet engine over a range of conditions of air flow, inlet pressure, inlet temperature, and fuel flow. Information was obtained on the combustion efficiencies, the effect on combustion of inlet variables, the altitude operational limits with two different fuels, the pressure losses in the combustor, the temperature and velocity profiles at the combustor outlet, the extent of afterburning, the fuel-injection characteristics, and the condition of the combustor basket.

Childs, J Howard↗
NASA NTRS1998

Results of a 24-inch Hybrid Motor Performance Uncertainty Analysis

The subscale (11 and 24-inch) hybrid motors at the Marshall Space Flight Center (MSFC) have been used as versatile and cost effective testbeds for developing new technology. Comparisons between motor configuration, ignition systems, feed systems, fuel formulations, and nozzle materials have been carried out without detailed consideration as to haw "good" the motor performance data were. For the 250,000 lb/thrust motor developed by the Hybrid Propulsion Demonstration Program consortium, this shortcoming is particularly risky because motor performance will likely be used as put of a set of downselect criteria to choose between competing ignition and feed systems under development. This analysis directly addresses that shortcoming by applying uncertainty analysis techniques to the experimental determination of the characteristic velocity, theoretical characteristic velocity, and characteristic velocity efficiency for a 24-inch motor firing. With the adoption of fuel-lined headends, flow restriction, and aft mixing chambers, state of the an 24-inch hybrid motors have become very efficient However, impossibly high combustion efficiencies (some computed as high as 108%) have been measured in some tests with 11-inch motors. This analysis has given new insight into explaining how these efficiencies were measured to be so high, and into which experimental measurements contribute the most to the overall uncertainty.

Sims, Joseph D.↗
NASA NTRS1951

Effects of Altitude on Turbojet Engine Performance

Component and over-all performance characteristics of several turbojet engines investigated in the altitude facilities of the NACA Lewis Laboratory during the last several years are summarized to indicate the effects of altitude on turbojet engine performance. Data presented show that failure of turbojet engine performance to generalize for all altitudes can be traced to reductions in compressor efficiency, corrected air flow, and combustion efficiency at altitude. In addition, it is shown that although engines of different design may have equal thrusts at sea level, the thrusts at altitude may vary widely because of differences in compressor performance characteristics from one engine to another.

COMPRESSORS - EFFICIENCY↗
NASA NTRS1981

Design, fabrication, test, and delivery of a high-pressure oxygen/RP-1 injector

A summary of the design analyses for a liquid rocket injector using oxygen and RP-1 propellants at high chamber pressures of 20,682 kPa (3000 psia) is presented. This analytical investigation includes combustion efficiency versus injector element type, combustion stability, and combustor cooling requirements. The design and fabrication of a subscale injector/acoustic resonantor assembly capable of providing a nominal thrust of 222K N (50,000 lbF) is presented.

Schoenman, L.↗
NASA NTRS1957

Investigation of Combustion in 16-inch Ram Jet Under Simulated Conditions of High Altitude and High Mach Number

Results obtained with three different burner configurations in a connected-pipe investigation of a 16-inch ram jet are presented. The radial position of the fuel injector and the engine-outlet area both affected burner performance. For a given configuration, only slight changes in total-pressure ratio across the combustion chamber were obtained over the complete range of operation. With one burner, combustion efficiencies obtained at a combustion-chamber-inlet static pressure of 800 pounds per square foot absolute were greater than those obtained at 1920 pounds per square foot absolute.

ENGINES, RAM JET↗
NASA NTRS1952

Evaluation of five conical center-body supersonic diffusers at several angles of attack

Five supersonic inlets having conical center bodies were investigated in a 16-inch ram jet engine with and without combustion at Mach numbers of 1.7, 1.9, and 2.0 and angles of attack from 0 degrees to 10 degrees. Four of the inlets were of the low-mass-flow-ratio type whereas the fifth inlet was of the high-mass-flow-ratio type. The stable operating range of the four low-nass-flow-ratio inlets decreased considerably as the angle of attack was increased despite an increase of the cone angle or the use of boundary-layer bleed. The stable range of the high-mass-flow-ratio inlet increased considerably both at 0 degrees and at greater angles of attack as the free-stream Mach number was decreased. Free-stream Mach number, angle of attack, and inlet type had negligible effects on combustion efficiency, temperature ratio, or combustion-chamber inlet Mach number in the supercritical region.

Englert, Gerald W↗