Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Brady”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Challenges in computationally designing high temperature Fe-based austenitic alloys: Addressing the role of Ni additions

Alumina-forming austenitic (AFA) alloys are relatively inexpensive high performance materials which combine the creep resistance of low-cost austenitic alloys and the oxidation resistance of expensive alumina forming alloys. However, a fundamental understanding of the role of key alloying elements such as Ni, Cr, Al, Nb, Ti, V, B and C in the experimentally observed oxidation behavior of these alloys is still lacking. The present work is a first in a series of studies aiming to quantitatively describe the role of Ni in promoting or disrupting protective Al 2 O 3 scale formation on AFA alloys. Here, ternary Fe-Al-xNi model alloys with three different Ni contents were isothermally exposed in an atmosphere with a low partial pressure of oxygen between 800–1000 °C for 24 h to evaluate the role of Ni in the observed internal oxidation behavior. Increasing Ni contents had no impact on the internal oxidation behavior of the alloys. The experimental and theoretical analyses in the present work suggested a negligible effect of the internal oxide precipitates on the inward diffusion of oxygen, typically expected in these systems, while simultaneously highlighting the barriers in the development of reliable models for computation-assisted design of these alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultra-efficient polymer binder for silicon anode in high-capacity lithium-ion batteries

As a highly promising anode material for high-capacity lithium-ion batteries (LIBs), the low electronic conductivity and large volume variation of silicon (Si) make the slurry-coating Si based electrode requiring high content of “inert” materials and suffering rapid capacity fading. In this work, a polyimine, synthesized via one-step condensation reaction, has been demonstrated as an ultra-efficient polymer binder that can resolve the above issues. The polyimine binder containing Si electrode delivers superior electrochemical performance: a delithiation specific capacity of 804.4 mAh g –1 with capacity retention of 82.4% after 1000 cycles at the current density of 2 A g –1 . The high efficiency of polyimine binder for Si electrode has also been demonstrated with ultrahigh weight ratio of “active” material to “inert” material (R A/I ). The electrode with 95 wt% of Si (95Si/Polyimine, R A/I = 19) reveals a reversible delithiation capacity of 2114 mAh g –1 (capacity retention ~ 80.4%) over 200 cycles at the current density of 400 mA g –1 . Even at the high current density of 2 A g –1 , a delithiation capacity of 1087.8 mAh g –1 after 500 cycles can be obtained. Molecular simulations and atomic force microscopy (AFM) indentation are utilized to investigate the ultra-efficiency of polyimine binder. With simple manufacturing process and ultra-efficient binder performance, the designed polyimine binder will be definitely meaningful in achieving low-cost and high-capacity LIBs with prolonged cycle life.

25 ENERGY STORAGE↗
DOE OSTI2024

Thermal stability of 3D interface Cu/Nb nanolaminates

Nanocrystalline alloys are promising structural materials yet lack thermal stability in many cases. Recent work shows that interface structure has an outsize effect on the thermal behavior of nanostructured alloys. Here, this work focuses on the role of controlled heterophase interface structure in the thermal evolution of model Cu/Nb nanolaminates. We introduce 3D interfaces containing nanoscale heterogeneities in all spatial dimensions between Cu and Nb, forming 3D Cu/Nb. TEM, nanoindentation, and DSC are used in tandem to establish thermal stability and to identify shifts in microstructure as a function of static annealing temperature. 3D interfaces are shown to survive annealing to 300 °C for 1 hr., while 3D Cu/Nb microstructure evolves to form low-density and voided regions correlating to the onset of layer pinch-off between 500 and 600 °C annealing temperatures. A diffusivity- and vacancy energetics-based mechanism is developed to explain void formation driven by 3D interface degradation at elevated temperature.

3D interfaces↗
DOE OSTI2021

Trace explosives sampling for security applications (TESSA) study: Evaluation of procedures and methodology for contact sampling efficiency

We report the detection of trace amounts of explosive materials is critical to the security at mass transit centers (e.g., airports and railway stations). In a typical screening process, a trap is used to probe a surface of interest to collect and transfer particulate residue to a detector for analysis. The collection of residues from the surface being probed is widely viewed as the limiting step in this process. A multi-institutional study was performed to establish a methodology for the evaluation of sampling media collection efficiencies. Dry deposited residues of 1,3,5-trinitroperhydro-1,3,5-triazine (RDX), C-4 (an RDX-based explosive), and pentaerythritol tetranitrate (PETN) were harvested from acrylonitrile butadiene styrene (ABS) plastic, ballistic nylon (NYL), and uncoated aluminum surfaces using muslin, Texwipe cotton, and stainless-steel mesh traps. Transfer and collection efficiencies of the sample media were calculated based on liquid chromatography-mass spectrometry analysis. Dry transfer efficiencies (DTE%) to all tested surfaces were greater than 75%, with transfer to ABS plastic being the lowest. Collection efficiency (CE%) varied significantly across the traps and the surfaces, yet some conclusions can be drawn; nylon had the lowest CE% for all cases (~10%), and the stainless steel mesh had the lowest CE% for the evaluated traps (~20%). Though the testing parameters have been standardized among the participants to establish a framework for an independent comparison of contact sampling media and surfaces, substantial variations in the DTE% and the CE% were observed, suggesting that other variables can affect contact sampling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Autoclave grid-to-rod fretting wear evaluation of a candidate cladding coating for accident-tolerant fuel

In pressurized water reactors (PWRs), water flow induced vibrations cause contact and rubbing between the fuel rods and the supporting grid, a phenomenon known as Grid-to-Rod-Fretting (GTRF). GTRF may produce progressive wear damage on the fuel claddings leading to subsequent leakage of radioactive fission products. Various accident-tolerant fuel (ATF) concepts are being developed for higher resistance to the high temperature steam and one approach is to apply a cladding coating. Here, fretting wear behavior of a candidate Cr-coating was investigated using a unique bench-scale autoclave testing rig mimicking the environment in an industrial full-assembly PWR simulator. The contact was under a realistically low load (~0.5 N) lubricated by deionized water at a temperature of 204 °C under a pressure of 20-23 bars. Results demonstrated that the Cr-coating significantly improved the cladding's wear resistance when tested against a commercial ZIRLO grid with or without pre-oxidization. In addition, the Cr-coating also reduced wear on the non-oxidized ZIRLO grid but slightly increased the wear on the pre-oxidized grid.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Uncovering novel mutational signatures by de novo extraction with SigProfilerExtractor

Mutational signature analysis is commonly performed in cancer genomic studies. Here, we present SigProfilerExtractor, an automated tool for de novo extraction of mutational signatures, and benchmark it against another 13 bioinformatics tools by using 34 scenarios encompassing 2,500 simulated signatures found in 60,000 synthetic genomes and 20,000 synthetic exomes. For simulations with 5% noise, reflecting high-quality datasets, SigProfilerExtractor outperforms other approaches by elucidating between 20% and 50% more true-positive signatures while yielding 5-fold less false-positive signatures. Applying SigProfilerExtractor to 4,643 whole-genome- and 19,184 whole-exome-sequenced cancers reveals four novel signatures. Two of the signatures are confirmed in independent cohorts, and one of these signatures is associated with tobacco smoking. In summary, this report provides a reference tool for analysis of mutational signatures, a comprehensive benchmarking of bioinformatics tools for extracting signatures, and several novel mutational signatures, including one putatively attributed to direct tobacco smoking mutagenesis in bladder tissues.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

In Situ Observations of Barium Sulfate Nucleation in Nanopores

In this work, the nucleation and growth of barium sulfate in nanoporous silica was investigated using in situ small-angle X-ray scattering and X-ray pair distribution function analysis, together with ex situ transmission and scanning transmission electron microscopy (TEM and STEM) imaging. We found that crystalline barite formation in micropores is likely preceded by a nonbulk barite phase in the nanopores, indicating a possible nonclassical nucleation pathway for barium sulfate under confinement. The nucleation of barium sulfate inside the nanopores stopped at ~12% of the pores filled and was seemingly limited by the formation of crystals near the exterior of the silica particles, which likely blocked subsequent solute transport into the interior of the nanopores. The growth rate of barium sulfate was fit using the Johnson–Mehl–Avrami–Kolmogorov equation and constrained using a growth rate of barite of ~1.0 × 10 –7 mol/m 2 /s, obtained from previous studies, but is consistent with TEM and STEM observations made here. The inferred nucleation rate of barium sulfate inside nanopores is estimated to be on the order of 1.0 × 10 9 nuclei/m 2 /s, which is 2 orders of magnitude higher than previous measurements on a planar silica substrate (~1.0 × 10 7 nuclei/m 2 /s). This implies that the ability of silica nanopores to promote barium sulfate nucleation is sufficiently high as to create a potentially self-limiting condition, where the nucleation reaction is shut down prematurely because rapid growth blocks reactant transport.

36 MATERIALS SCIENCE↗
DOE OSTI2025

On the Structural Origin of Fast Li-Ion Cycling in Tetragonal Bronze-Type Nb 8 W 9 O 47

Bronze and bronze-derived, mixed metal oxides are materials of growing interest for lithium-ion battery anodes due to their high-rate capabilities and the potential for high energy densities via multielectron redox. We report on the synthesis and electrochemical properties of the tetragonal tungsten bronzetype phase Nb 8 W 9 O 47 and our investigation into the structural evolution of this phase upon lithium (de)intercalation, with particular attention to how it relates to the fast-cycling capabilities. Electrochemical cycling shows Nb 8 W 9 O 47 can achieve greater than one Li + per transition metal at rates of C/2 or slower and maintains a capacity equivalent to 0.65 Li + per transition metal at a rate of 20C. Sequential Rietveld analysis of operando X-ray diffraction data reveals anisotropic changes to the unit cell parameters during discharge, accompanied by an off-centering of the transition metals within their octahedral environments. While higher capacities can be accessed below 1.2 V, cells discharged to 1.0 V exhibit a significant expansion of the unit cell volume and reduced Coulombic efficiencies. This report suggests that rigid crystal structures incapable of undergoing polyhedral rotational deformations can instead exploit displacive distortions of the transition metal redox center to enable fast Li-ion cycling with minimal atomic rearrangements.

25 ENERGY STORAGE↗
DOE OSTI2021

Corrosion of Ferrous Structural Alloys in Biomass Derived Fuels and Organic Acids

This work investigated the corrosivity of biomass-derived liquid fuels and organic acids associated with bio-oils and conducted a corrosion compatibility evaluation of several structural ferrous alloys in the fuels and acids. Here, the acidity parameters and solution conductivity values were higher in raw pyrolysis bio-oils than postprocessed oils with significant corrosion attack for carbon steel and Fe-2.25Cr-1Mo. However, higher-grade stainless steels, ferritic Fe-15Cr (15Cb) and austenitic types 304L and 316L, showed negligible corrosion loss, whereas lower-Cr ferritic grades 409, 410, and 416 were attacked. Metal leaching tests and electrochemical impedance spectroscopy measurements revealed superior corrosion resistance of 316 over 410 stainless steels in solutions of formic and oxalic acids that can be present in bio-oils. The corrosion evaluation methods utilized in this work provide effective screening tools to identify the compatible structural alloys for bio-oils.

09 BIOMASS FUELS↗
DOE OSTI2023

Performance of Structural Alloys in Bio-oil Production, Upgrading, and Storage Systems

Selection of corrosion-resistant, cost-effective structural materials for the process and containment vessels required for the production, upgrading, and storage of biomass-derived oils has been the subject of study in our laboratory for many years. The wide variety of biomass resources and the many liquefaction techniques and processing conditions result in products with a broad range of properties and compositions. Here, this paper will address the materials issues in three distinct areas. In production, materials are exposed to temperatures that range from 350 to 550 °C depending upon the process. Generally, austenitic stainless steels have performed reasonably well, although thicker oxide scales and intergranular attack have sometimes been observed. For storage and transport of the bio-oil products, temperatures experienced by the containment materials are not expected to exceed 50 °C. Our studies have shown that most raw bio-oils contain significant concentrations of organic acids, and low-molecular-weight organic acids were quite corrosive to carbon and low alloy steels. For some applications, subsequent processing is required, which includes hydrotreating or co-processing with a petroleum-derived liquid. These processes utilize a catalyst that requires periodic retreatment with a sulfidizing gas, and the exposure to this gas at elevated temperatures can cause appreciable corrosion to the more common austenitic stainless steels. The materials considered most cost-effective and sufficiently corrosion-resistant for each of these environments were identified.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Surface Reactivity Analysis of the Crude Oil–Brine–Limestone Interface for a Comprehensive Understanding of the Low-Salinity Waterflooding Mechanism

Low-salinity waterflooding (LSWF) has proven to improve oil recovery in carbonate formations through rock wettability alteration, although the underlying mechanism remains elusive. Multivalent ionic exchange and calcite dissolution have usually been investigated using geochemical analysis in secondary coreflooding. In this work, coreflooding, in tertiary mode, coupled with a surface reactivity analysis approach was employed to investigate the interplay of wettability alteration mechanisms such as mineral dissolution, electrostatic bond attraction, and the effect of pH at in situ conditions. Improved oil recovery (IOR) in tertiary mode observed by coreflooding in Indiana limestone rocks showed an ionic strength dependence, that is, reducing brine ionic strength resulted in an increase in oil recovery. Coreflooding results showed that the seawater and low-salinity brines deprived of Mg 2+ ions resulted in the lowest IOR in tertiary mode, indicating the significance of Mg 2+ on IOR in limestone rocks. Similar results were observed through the contact angle measurement showing the limestone rock wettability state dependence on ionic strength and the effect of Mg2+ ions. Surface reactivity analysis showed an increase in solution pH, Ca 2+ and Mg 2+ ions concentration in the effluent solution from the coreflooding in tertiary mode using low salinity brines (about 40 and 20% increase in the effluent composition for Ca 2+ and Mg 2+ , respectively). These changes in solution composition were used to calculate the in situ oil–brine and rock–brine zeta potential using a validated surface complexation model, showing the changes of zeta potential as brine is injected into limestone rocks. The results show that using seawater-like brine in tertiary mode resulted in no mineral dissolution or ionic exchange. However, improved oil recovery (IOR) using such seawater-like brine was due to wettability alteration caused by reduced electrostatic bond attraction associated with Mg 2+ ions [from 2.6 × 10 –13 (mol/m 2 ) 2 for formation water salinity to 1.5 × 10 –13 (mol/m 2 ) 2 for seawater salinity]. Using low-salinity brines in tertiary mode improved oil recovery by mineral dissolution, resulting in oil desorption and an increase in solution pH. Finally, the increase in solution pH also resulted in reduced electrostatic bond attraction which lead to rock wettability alteration using low-salinity brines.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2020

Corrosion Susceptibility of Cr–Mo Steels and Ferritic Stainless Steels in Biomass-Derived Pyrolysis Oil Constituents

In this work, to better understand and evaluate the corrosion performance of candidate structural steels and ferritic stainless steels for production, transport, and storage of biomass pyrolysis oils, corrosion studies were conducted in selected organic constituents of bio-oils, including catechol, formic acid, and their mixtures as well as lactobionic acid, using electrochemical impedance spectroscopy. R 2 , the resistance against corrosion reaction, was obtained by fitting measured impedance spectra into an equivalent circuit. The values of R 2 were then used to assess corrosion resistance of the steels in each organic constituent and mixture. Type 410 and 430 stainless steels were resistant to corrosion in all tested organic constituents, while 2.25Cr-1Mo steel was not. 9Cr-1Mo steel was corrosion resistant in catechol but not in the other mixtures that contained organic acids. On the basis of the results of this work, it is suggested that the corrosion resistance against organic acids is attributed to formation of a Cr-rich passive film that requires stainless steels with critical Cr levels in excess of approximately 11 wt %. In catechol-only solution, lower levels of Cr intermediate between that of 2.25Cr-1Mo steel and 9Cr-1Mo steel appeared sufficient.

36 MATERIALS SCIENCE↗