SEARCH · Engineering Papers

Results for “Boundary Layer Profiles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Investigation of Inlet Concepts for Maneuver Improvement at Transonic Speeds

A 15 percent scale lightweight fighter type inlet forebody was tested in the Ames 14 foot transonic wind tunnel at Mach numbers of 0.7, 0.9, and 1.04. The inlet was a two dimensional horizontal ramp system designed for a Mach number of 2.2. Four inlet devices designed to prevent or delay cowl-lip boundary layer separation or to improve the inlet internal flow characteristics at high angles of attack were investigated. The devices used to control cowl-lip separation consisted of cowl leading edge flaps, slotted flaps, and tangential blowing. To improve the internal flow characteristics, discrete jet nozzle flows were directed downstream and parallel to the duct surface in the subsonic diffuser to energize the wall boundary layer. The discrete jets used in the subsonic diffuser were also tested in combination with each of the cowl leading edge devices. Test measurements included engine-face total pressure recovery, steady state distortion, dynamic distortion, duct boundary layer profiles, and duct-surface static pressures.

Latham, E.↗

NASA NTRS1977

Prediction of outer layer mixing lengths in turbulent boundary layers

Predictions of mixing length by Pletcher's (1976) method (using a two-layer eddy viscosity model for a turbulent boundary layer at low Reynolds numbers) are compared to some values derived from turbulent boundary-layer profiles by other authors. The model is incorporated into a finite-difference scheme, to accurately predict low Reynolds number skin friction in supersonic flow.

Watson, R. D.↗

NASA NTRS1978

Direct measurements and analysis of skin friction and cooling downstream of multiple flush-slot injection into a turbulent Mach 6 boundary layer

Experiments were conducted to determine the reduction in surface skin friction and the effectiveness of surface cooling downstream of one to four successive flush slots injecting cold air at an angle of 10 deg into a turbulent Mach 6 boundary layer. Data were obtained by direct measurement of surface shear and equilibrium temperatures, respectively. Increasing the number of slots decreased the skin friction, but the incremental improvement in skin-friction reduction decreased as the number of slots was increased. Cooling effectiveness was found to improve, for a given total mass injection, as the number of slots was increased from one to four. Comparison with previously reported step-slot data, however, indicated that step slots with tangential injection are more effective for both reducing skin friction and cooling than the present flush-slot configuration. Finite-difference predictions are in reasonable agreement with skin-friction data and with boundary-layer profile data.

Howard, F. G.↗

NASA NTRS1977

Optical and acoustical measuring techniques

The paper reviews the techniques of laser and acoustic Doppler measurement of fluid velocities in confined and free flows. The main mathematical relations are presented, and some systems are studied. Resolution properties of coaxial, bistatic, and pulsed CO2 laser Doppler velocimeter systems are compared. Schematics for pulsed and continuous wave acoustic Doppler systems are discussed. Both of these types of systems benefit from using a bistatic configuration instead of a coaxial system. The pulsed systems avoid contamination of source noise by not sampling until after the source noise has passed the receiver. Comparison of wind velocity measured with a pulsed acoustic Doppler and with a boundary layer profile is made.

Cliff, W. C.↗

NASA NTRS1979

Three component velocity measurements in an upper surface blowing configuration

In four recent papers, results of an experimental investigation of a freely expanding coflowing jet as well as a three dimensional wall jet have been presented. A flat plate and a curved wall surface modelling a wing-flap combination in a high lift V/STOL configuration have been documented as to their effects on the flow field. The ratio of the jet exit plane velocity to the free stream velocity was varied from 5.1 to 10.9 to 1. This report continues the documentation of the three dimensional wall jet with special emphasis on the vertical and lateral mean and fluctuating velocities. Additionally, boundary layer profiles over both the flat plate and the flap are presented.

Catalano, G. D.↗

NASA NTRS1980

Flow visualization of inflexional instabilities on a rotating disk

Experiments were conducted on a rotating disk in water using dye to observe the formation of small vortices in the boundary layer due to the inflexional nature of the boundary layer profiles in the radial and near radial directions. Such vortices have also been detected near the leading edge of swept wings and on the windward side of fuselages at angles of attack using sublimation techniques. In the present investigation, color motion pictures at 300 frames per second were taken and the vortex spacing, angles of inclination of the vortex axes and critical Reynolds numbers were determined from these films. Secondary instabilities were also observed and analyzed.

Clarkson, M. H.↗

NASA NTRS1980

Numerical simulation of steady supersonic flow over an ogive-cylinder-boattail body

A recently reported parabolized Navier-Stokes code has been employed to compute the supersonic flow field surrounding an ogive-cylinder-boattail body at incidence. The computations were performed for flow conditions where an extensive series of experimental surface pressure and turbulent boundary-layer profile measurements had been obtained. Comparison between the computational results and experimental measurements for angles of attack up to 6 deg show excellent agreement. At angles greater than 6 deg discrepancies are observed which are tentatively attributed to three-dimensional turbulence modeling errors.

Schiff, L. B.↗

NASA NTRS1978

The characteristics of evolving mesoscale systems over mountainous terrain as revealed by radar and PAM

The paper deals with measurements made within the South Park area (which is located near Denver, Colorado, and is a natural genesis area for cumulus clouds) in July and August 1977, using powered aircraft, sailplanes, rawinsondes, boundary layer profilers, acoustic sounders, micrometeorological towers, lidar, research radar, triple-Doppler radar, and a square grid of surface meteorological stations. Extensive analysis revealed a very complex picture of thunderstorm-scale, large-mesoscale, and synoptic-scale interactions.

George, R. L.↗

NASA NTRS1981

The boundary layer on compressor cascade blades

The flow field about an airfoil in cascade at a Reynolds number of 5 x 10 to the 5th power is described. Hot wire and laser anemometry are combined with flow visualization techniques in order to obtain detailed flow data (e.g., boundary layer profiles, points of separation, and the transition zone) on a cascade of relatively highly loaded blades. Benchmark data is provided for the evaluation of current and future predictive models, in this way aiding in the compressor design process.

Deutsch, S.↗

NASA NTRS1981

Efficient computation of the stability of three-dimensional compressible boundary layers

Methods for the computer analysis of the stability of three-dimensional compressible boundary layers are discussed and the user-oriented Compressible Stability Analysis (COSAL) computer code is described. The COSAL code uses a matrix finite-difference method for local eigenvalue solution when a good guess for the eigenvalue is available and is significantly more computationally efficient than the commonly used initial-value approach. The local eigenvalue search procedure also results in eigenfunctions and, at little extra work, group velocities. A globally convergent eigenvalue procedure is also developed which may be used when no guess for the eigenvalue is available. The global problem is formulated in such a way that no unstable spurious modes appear so that the method is suitable for use in a black-box stability code. Sample stability calculations are presented for the boundary layer profiles of an LFC swept wing.

Malik, M. R.↗

NASA NTRS1982

Investigation of the tip clearance flow inside and at the exit of a compressor rotor passage

The nature of the tip clearance flow in a moderately loaded compressor rotor is studied. The measurements were taken inside the clearance between the annulus-wall casing and the rotor blade tip. These measurements were obtained using a stationary two-sensor hot-wire probe in combination with an ensemble averaging technique. The flowfield was surveyed at various radial locations and at ten axial locations, four of which were inside the blade passage in the clearance region and the remaining six outside the passage. Variations of the mean flow properties in the tangential and the radial directions at various axial locations were derived from the data. Variation of the leakage velocity at different axial stations and the annulus-wall boundary layer profiles from passage-averaged mean velocities were also estimated.

Pandya, A.↗

NASA NTRS1982

Finite-difference solution of the compressible stability eigenvalue problem

A compressible stability analysis computer code is developed. The code uses a matrix finite difference method for local eigenvalue solution when a good guess for the eigenvalue is available and is significantly more computationally efficient than the commonly used initial value approach. The local eigenvalue search procedure also results in eigenfunctions and, at little extra work, group velocities. A globally convergent eigenvalue procedure is also developed which may be used when no guess for the eigenvalue is available. The global problem is formulated in such a way that no unstable spurious modes appear so that the method is suitable for use in a black box stability code. Sample stability calculations are presented for the boundary layer profiles of a Laminar Flow Control (LFC) swept wing.

Malik, M. R.↗

NASA NTRS1982

Observations and implications of natural laminar flow on practical airplane surfaces

The results of natural laminar flow (NLF) experiments conducted by NASA to determine if modern aircraft structures can benefit from NLF as do sailplanes are presented. Seven aircraft, ranging from a Cessna 210 to a Learjet 28/29, with relatively stiff skins were flown in production configurations with no modifications. Measurements were made of the boundary-layer laminar to turbulent transition locations on various aerodynamic surfaces, the effect of a total loss of laminar flow, the effect of the propeller slipstream on the wing boundary-layer transition and the boundary-layer profiles, the wing section profile drag, the effect of flight through clouds, and insect debris contamination effects. Favorable pressure gradients for NLF were concluded to be feasible up to a transition Reynolds number of 11 million. Laminar flows were observed in propeller slipstreams, and insects were found to cause transition 1/4 of the time.

Holmes, B. J.↗

NASA NTRS1983

End wall flow characteristics and overall performance of an axial flow compressor stage

This review indicates the possible future directions for research on endwall flows in axial flow compressors. Theoretical investigations on the rotor blade endwall flows in axial flow compressors reported here include the secondary flow calculation and the development of the momentum integral equations for the prediction of the annulus wall boundary layer. The equations for secondary vorticity at the rotor exit are solved analytically. The solution includes the effects of rotation and the viscosity. The momentum integral equations derived include the effect of the blade boundary layers. The axial flow compressor facility of the Department of Aerospace Engineering at The Pennsylvania State University, which is used for the experimental investigations of the endwall flows, is described in some detail. The overall performance and other preliminary experimental results are presented. Extensive radial flow surveys are carried out at the design and various off design conditions. These are presented and interpreted in this report. The following experimental investigations of the blade endwall flows are carried out. (1) Rotor blade endwall flows: The following measurements are carried out at four flow coefficients. (a) The rotor blade static pressures at various axial and radial stations (with special emphasis near the blade tips). (b) The hub wall static pressures inside the rotor blade passage at various axial and tangential stations. (2) IGV endwall flows: The following measurements are carried out at the design flow coefficient. (a) The boundary layer profiles at various axial and tangential stations inside the blade passage and at the blade exit. (b) Casing static pressures and limiting streamline angles inside the blade passage.

Sitaram, N.↗

NASA NTRS1983

Design procedures for compressor blades

The conventional methods for the design of the blades in the case of axial turbomachines are considered, taking into account difficulties concerning the determination of optimal blade profiles. These difficulties have been partly overcome as a consequence of the introduction of new numerical methods during the last few years. It is pointed out that, in the case of the subsonic range, a new procedure is now available for the determination of the form of blade profile on the basis of a given velocity distribution on the profile surface. The search for a profile form with favorable characteristics is consequently transformed into a search for a favorable velocity or pressure distribution on the blade. The distribution of velocities depends to a large degree on the characteristics of the profile boundary layers. The considered concept is not new. However, its practical implementation has only recently become possible. The employment of the new design procedure is illustrated with the aid of an example involving a concrete design problem.

Starken, H.↗

NASA NTRS1984

Stability of the laminar boundary layer in a streamwise corner

The stability of viscous, incompressible flow along a streamwise corner, often called the corner boundary layer problem is examined. The semi-infinite boundary value problem satisfied by small amplitude disturbances in the "bending boundary layer' region is obtained. The mean secondary flow induced by the corner exhibits a flow reversal in this region. Uniformly valid "first approximations' to solutions of the governing differential equations are derived. Uniformity at infinity is achieved by a suitable choice of the large parameter and use of an approximate Langer variable. Approximations to solutions of balanced type have a phase shift across the critical layer which is associated with instabilities in the case of two dimensional boundary layer profiles.

Lakin, W. D.↗

NASA NTRS1984

Inlet flowfield investigation. Part 2: Computation of the flow about a supercruise forebody at supersonic speeds

A numerical procedure which solves the parabolized Navier-Stokes (PNS) equations on a body fitted mesh was used to compute the flow about the forebody of an advanced tactical supercruise fighter configuration in an effort to explore the use of a PNS method for design of supersonic cruise forebody geometries. Forebody flow fields were computed at Mach numbers of 1.5, 2.0, and 2.5, and at angles-of-attack of 0 deg, 4 deg, and 8 deg. at each Mach number. Computed results are presented at several body stations and include contour plots of Mach number, total pressure, upwash angle, sidewash angle and cross-plane velocity. The computational analysis procedure was found reliable for evaluating forebody flow fields of advanced aircraft configurations for flight conditions where the vortex shed from the wing leading edge is not a dominant flow phenomenon. Static pressure distributions and boundary layer profiles on the forebody and wing were surveyed in a wind tunnel test, and the analytical results are compared to the data. The current status of the parabolized flow flow field code is described along with desirable improvements in the code.

Paynter, G. C.↗

NASA NTRS1984

Stability of the laminar boundary layer in a streamwise corner

The stability of viscous, incompressible flow along a streamwise corner, often called the corner boundary layer problem is examined. The semi-infinite boundary value problem satisfied by small amplitude disturbances in the 'bending boundary layer' region is obtained. The mean secondary flow induced by the corner exhibits a flow reversal in this region. Uniformly valid 'first approximations' to solutions of the governing differential equations are derived. Uniformity at infinity is achieved by a suitable choice of the large parameter and use of an approximate Langer variable. Approximations to solutions of balanced type have a phase shift across the critical layer which is associated with instabilities in the case of two dimensional boundary layer profiles. Previously announced in STAR as N84-17532

Lakin, W. D.↗