Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Bi”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Bi-directional reflectance of finite and infinite clouds

The transfer of solar irradiance in plane parallel and broken cloud fields is modeled using a Monte Carlo method. The angular distribution pattern of radiances exiting the cloud layer is studied with varying cloud geometries, optical thicknesses, cloudiness and solar zenith angles. A rather large anisotropy of the reflected flux is found, usually increasing with solar zenith angle and with patterns that strongly depend on cloud geometry. The main features are: a local maximum of reflected intensity in the forward direction for all cases; a limb darkening for the plane parallel case; and a limb brightening and a local maximum of reflected intensity in the backward direction for broken clouds. The method is used to study the cloud reflectance sensitivity to various parameters. A more precise description of cloud field internal and external structure is needed in order to obtain accurate bi directional reflectance diagrams.

Breon, Francois-Marie↗
NASA NTRS1991

Dependence of transition temperature on hole concentration per CuO2 sheet in the Bi-based superconductors

The recently observed variations of the transition temperature (T sub c) with oxygen content in the Bi based (2212) and (2223) superconductors are analyzed in terms of p+, the hole concentration per CuO2 sheet. This analysis shows that in this system, T sub c increases with p+ initially, reaching maxima at p+ = 0.2 approx. 0.3, followed by monotonic decrease of T sub c with p+. The forms of these variations are similar to those observed in the La(2-x)Sr(x)CuO4 and YBa2Cu3Oy systems, suggesting that p+ may be an important variable governing superconductivity in the cuprate superconductors.

Zhao, J.↗
NASA NTRS1991

Effect of doping in the Bi-Sr-Ca-Cu-O superconductor

The results of the effect of doping on the superconducting transition in the Bi-Sr-Ca-Cu-O system are reported. Samples were prepared under identical conditions with varying types (Pb, Sb, Sn, Nb) and amounts of dopants. All samples consisted of multiple phases, and showed stable and reproducible superconducting transitions. Stabilization of the well known 110 K phase depends on both the type and amount of dopant. No trace of superconducting phase of 150 K and above was observed.

Akbar, S. A.↗
NASA NTRS1991

Processing Bi-Pb-Sr-Ca-Cu-O superconductors from amorphous state

The bismuth based high T sub c superconductors can be processed via an amorphous Bi-Pb-Sr-Ca-Cu oxide. The amorphous oxides were prepared by melting the constituent powders in an alumina crucible at 1200 C in air followed by pouring the liquid onto an aluminum plate, and rapidly pressing with a second plate. In the amorphous state, no crystalline phase was identified in the powder x ray diffraction pattern of the quenched materials. After heat treatment at high temperature the amorphous materials crystallized into a glass ceramic containing a large fraction of the Bi2Sr2Ca2Cu3O(x) phase T sub c = 110 K. The processing method, crystallization, and results of dc electrical resistivity and ac magnetic susceptibility measurements are discussed.

Chiang, C. K.↗
NASA NTRS1991

Study of the superconducting properties of the Bi-Ca-Sr-Cu-O system

High Temperature Superconductivity in the Bi-Ca-Sr-Cu-O System has been observed and has attracted considerable attention in 1988. The 80 K superconductivity phase has been identified to have a composition of Bi2CaSr2Cu2Ox, while the 110 K phase as reported in the literature has a possible composition of Bi2Ca2Sr2Cu3O(x). Researchers present here a study of the electrical properties of bulk samples of the slowly cooled and rapidly quenched 2:1:2:2 system. The samples used in this study were prepared from appropriate amounts of Bi2O3, CuO, SrCO3, CaCO3.

Khan, Musheer H.↗
NASA NTRS1991

Magnetic relaxation in the 110 K superconducting phase in Bi-Sr-Ca-Cu-O thin films

We have investigated the time dependence of remnant moment decay in a highly oriented, nearly single high T(sub c) phase Bi-Sr-Ca-Cu-O thin film. A strictly logarithmic time dependence was observed over a 20 K temperature range for observation intervals of 2000 seconds. The normalized decay rate exhibits a peak around 14 K and has a relatively weak magnetic field dependence. These data are then compared with existing data on the YBCO and Eu-based superconductors.

Tanaka, Atsushi↗
NASA NTRS1991

An explanation for the rise in Tc in the Tl- and Bi-based high temperature superconductors

Using the plasmon exchange model for the high T(sub c) superconductor, it is shown that the T(sub c) rises with an increase in the number of CuO layers per unit cell, which is in agreement with recent observations in the Tl- and Bi-based compounds. The calculation also suggests that the sample will become superconducting in successive stages and that there is a saturation effect, i.e., that T(sub c) cannot be raised indefinitely by increasing the number of CuO layers.

Bose, S. M.↗
NASA NTRS1992

Screen printed Y and Bi-based superconductors

High T(sub c) superconducting thick film was prepared by screen printing process. Y-based (YBa2Cu3O(7 - x)) superconducting thick films were printed on 211/Al2O3, SNT/Al2O3, and YSZ substrates. Because of poor adhesion of the superconducting thick films to 211/Al2O3 and SNT/Al2O3 substrates, relatively low T(sub c) and J(sub c) values were obtained from the films printed on these substrates. Critical temperatures of YBa2Cu3O(7 - x) thick films deposited on 211/Al2O3 and SNT/Al2O3 substrates were about 80 K. The critical current densities of these films were less than 2 A/cm(exp 2). Higher T(sub c) and J(sub c) films were printed on the YSZ substrates; T(sub c) = 86.4 K and J(sub c) = 50.4 A/cm(exp 2). Multiple lead samples were also prepared on the YSZ substrates. These showed lower T(sub c) and J(sub c) values than plain samples. The heat treatment conditions of the multiple lead samples are still under investigation. Bi-based superconductor thick films have been obtained so far. Improving the superconducting properties of the BSCCO screen printed thick films will be emphasized in future work.

Haertling, Gene H.↗
NASA NTRS1993

Research On Bi-Based High-Temperature Superconductors

Brief report describes effects of melt sintering on Bi-based high-temperature superconductor system, as well as use of vibrating-sample magnetometer to determine hysteresis curves at 77 K for partially melt-sintered samples. Also discussed is production of high-temperature superconducting thin films by laser ablation: such films potentially useful in detection of signals of very low power.

Banks, Curtis↗
NASA NTRS1992

Planar laser-induced fluorescence imaging of OH in the exhaust of a bi-propellant thruster

Planar laser-induced fluorescence imaging of the hydroxyl radical has been performed on the flow produced by the exhaust of a subscale H2/O2 fueled bi-propellant rocket engine. Measurements were made to test the feasibility of OH (0,0) and (3,0) excitation strategies by using injection seeded XeCl and KrF excimer lasers, respectively. The flow is produced with hydrogen and oxygen reacting at a combustor chamber pressure of 5 atm which then exhausts to the ambient. The hydroxyl concentration in the exhaust flow is approximately 8 percent. Fluorescence images obtained by pumping the Q1(3) transition in the (0,0) band exhibited very high signals but also showed the effect of laser beam absorption. To obtain images when pumping the P1(8) transition in the (3,0) band it was necessary to use exceptionally fast imaging optics and unacceptably high intensifier gains. The result was single-shot images which displayed a signal-to-noise ratio of order unity or less when measured on a per pixel basis.

Paul, Phillip H.↗
NASA NTRS1993

Development of high Tc (greater than 100 K) Bi, Tl and Y-based materials as superconducting circuit elements

Results on this project over the past three years have shown that the Bi and Tl-based superconducting materials in bulk form are noticeably different from the Y-based 123 material in that superconductivity is considerably harder to achieve, maintain and reproduce. This is due primarily to the difficulty in obtaining the higher Tc phase in pure form since it commonly co-exists with other undesirable, lower Tc phases. In particular, it has been found that long processing times for calcining and firing (20 - 200 hrs.) and close control of temperatures which are very near the melting point are required in order to obtain higher proportions of the desirable, high Tc (2223) phase.

Haertling, Gene↗
NASA NTRS1993

Bi-directional reflectance and other radiation parameters of cirrus from ER-2 observations

Passive and active remote sensing of cirrus were acquired from the ER-2 high altitude aircraft in the 1991 Cirrus Experiment. The observations include direct measurements of cirrus bi-directional reflectance from a new translinear scanning radiometer and the previously employed measurements by lidar and visible-infrared imaging radiometers. For any cirrus radiative transfer application, it is necessary to know the appropriate model for visible reflectance in relation to angle and also the optical thickness and infrared emissivity of the clouds. At a more complicated level, for remote sensing and overall cloud effects it is ultimately required to understand effects from multiple cloud layers, broken clouds, and variable microphysics. Our overall data set from the scanning radiometers and lidar is intended to provide the necessary observations to investigate these problems.

Spinhime, James↗
NASA NTRS1995

Effect of neutron irradiation on the London penetration depth for polycrystalline Bi(1.8)Pb(0.3)Sr2Ca2Cu3O10 superconductor

Magnetization studies of polycrystalline Bi(1.8)Pb(0.3)Sr2Ca2Cu3O10 superconductor, prior to and after neutron irradiation, showed an increase in J(sub c) due to irradiation damage. Analysis of the equilibrium magnetization revealed significant increases in other more fundamental properties. In particular, the London penetration depth increased by approximately 15 percent following irradiation with 8 x 10(exp 16) neutrons/sq cm. Corresponding changes were observed in the upper critical magnetic field H(sub c2). However, the most fundamental thermodynamic property, the superconductive condensation energy F(sub c), was unaffected by the moderate level of neutron-induced damage.

Ossandon, J. G.↗
NASA NTRS1995

Correlation between fabrication factor and superconducting properties of the Tl-and-Bi-based high-Tc superconductor

Large critical current densities (J(sub c)) were obtained in c axis oriented Tl-1 223/Ag composite tapes fabricated by spraying methods without a vacuum. Transport measurements at 77K under a zero field indicated a J(sub c) of 9 x 10(exp 4) A/sq cm and 7 x 10(exp 3) A/sq cm at 1T for the tapes fabricated by spray pyrolysis. The novel GPM method was also applied for Bi-2212/Ag PIT composite wire, and found to be very effective for improving the distribution of voids, which caused from the melt-solidifying process. The GPM showed a marked effect for obtaining homogeneous long wire. A 1 T class coil was successfully fabricated with monocore wire.

Maki, Naoki↗
NASA NTRS1995

Structure and superconductivity in (Bi(0.35)Cu(0.65))Sr2YCu2O7 and related materials

The recently reported (Bi/Cu)Sr2YCu2O7 phase has been studied by time of flight powder neutron diffraction. The proposed 1212 structure has been confirmed and refinements have shown the oxygen in the (Bi/Cu)O layer is displaced by 0.78 A from the ideal (1/2,1/2,0) site (P4/mmm space group) along /100/. Bond Valence Sum calculations have suggested oxidation states of Bi(5+) and Cu(2+) for the cations in the (Bi/Cu)O layers. The material is non-superconducting and all attempts to induce superconductivity have been unsuccessful. Work on the related material (Ce/Cu)Sr2YCu2O7 has shown the ideal Ce content to be 0.5 Ce per formula unit. The introduction of Ba (10%) onto the Sr site dramatically increases phase stability and also induces superconductivity (62 K).

Jennings, R. A.↗
NASA NTRS1995

Progress in development of tapes and magnets made from Bi-2223 superconductors

Long lengths of (Bi,Pb)2Sr2Ca2Cu3O(x) tapes made by powder-in-tube processing have been wound into coils. Performance of the coils has been measured at temperatures of 4.2 to 77 K, and microstructures have been examined by x-ray diffraction and electron microscopy and then related to superconducting properties. A summary of recent results and an overview of future goals are presented.

Balachandran, U.↗
NASA NTRS1995

Percolation effect in thick film superconductors: Using a Bi(Pb)SrCaCuO based paste to prepare a superconducting planar transformer

A thick film superconductor paste has been developed to study the properties of granulated superconductor materials, to observe the percolation effect and to confirm the theory of the conducting mechanism in the superconducting thick films. This paste was also applied to make a superconducting planar transformer. Due to the T(sub c) and advantageous current density properties the base of the past was chosen to be of Bi(Pb)SrCaCu) system. For contacts a conventional Ag/Pt paste was used. The critical temperature of the samples were between 110 K and 115 K depending on the printed layer thickness. The critical current density -at the boiling temperature of the liquid He- was between 200 - 300 A/sq cm. The R(T) and V(I) functions were measured with different parameters. The results of the measurements have confirmed the theory of conducting mechanism in the material. The percolation structure model has been built and described. As an application, a superconducting planar thick film transformer was planned and produced. Ten windings of the transformer were printed on one side of the alumina substrate and one winding was printed on the other side. The coupling between the two sides was possible through the substrate. The samples did not need special drying and firing parameters. After the preparation, the properties of the transformer were measured. The efficiency ans the losses were determined. Finally, some fundamental advantages and problems of the process were discussed.

Sali, Robert↗