Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Separation of switchgrass bio-oil by water/organic solvent addition and pH adjustment

Applications of bio-oil are limited by its challenging properties including high moisture content, low pH, high viscosity, high oxygen content, and low heating value. Separation of switchgrass bio-oil components by adding water, organic solvents (hexadecane and octane), and sodium hydroxide may help to overcome these issues. Acetic acid and phenolic compounds were extracted in aqueous and organic phases, respectively. Polar chemicals, such as acetic acid, did not partition in the organic solvent phase. Acetic acid in the aqueous phase after extraction is beneficial for a microbial-electrolysis-cell application to produce hydrogen as an energy source for further hydrodeoxygenation of bio-oil. Organic solvents extracted more chemicals from bio-oil in combined than in sequential extraction; however, organic solvents partitioned into the aqueous phase in combined extraction. When sodium hydroxide was added to adjust the pH of aqueous bio-oil, organic-phase precipitation occurred. As the pH was increased, a biphasic aqueous/organic dispersion was formed, and phase separation was optimized at approximately pH 6. The neutralized organic bio-oil had approximately 37% less oxygen and 100% increased heating value than the initial centrifuged bio-oil. In conclusion, the less oxygen content and increased heating value indicated a significant improvement of the bio-oil quality through neutralization.

09 BIOMASS FUELS↗

Effect of Acid, Alkali, and Steam Explosion Pretreatments on Characteristics of Bio-Oil Produced from Pinewood

Here, bio-oil produced from pinewood by fast pyrolysis has the potential to be a valuable substitute for fossil fuels. Pretreatment prior to the fast pyrolysis process has been shown to alter the structure and chemical composition of biomass. To determine the influence of biomass pretreatments on bio-oil produced during fast pyrolysis, we tested three pretreatment methods: dilute acid, dilute alkali, and steam explosion. Bio-oils were produced from untreated and pretreated pinewood feedstocks in an auger reactor at 450°C. The bio-oils physical properties including pH, water content, acid value, density, viscosity, and heating value were measured. Chemical characteristics of the bio-oils were determined by gas chromatographymass spectrometry. Results showed that bio-oil yield and composition were influenced by biomass pretreatment. Of the three pretreatment methods, 1% H 2 SO 4 pretreatment resulted in the highest bio-oil yield and best bio-oil quality.

09 BIOMASS FUELS↗

Life-Cycle Assessment of Pyrolysis Bio-Oil Production*

As part ofthe Consortium for Research on Renewable Industrial Materials' Phase I life-cycle assessments ofbiofuels, lifecycle inventory burdens from the production of bio-oil were developed and compared with measures for residual fuel oil. Bio-oil feedstock was produced using whole southern pine (Pinus taeda) trees, chipped, and converted into bio-oil by fast pyrolysis. Input parameters and mass and energy balances were derived with Aspen. Mass and energy balances were input to SimaPro to determine the environmental performance of bio-oil compared with residual fuel oil as a heating fuel. Equivalent functional units of 1 MJ were used for demonstrating environmental preference in impact categories, such as fossil fuel use and global warming potential. Results showed near carbon neutrality of the bio-oil. Substituting bio-oil for residual fuel oil, based on the relative carbon emissions of the two fuels, estimated a reduction in CO2 emissions by 0.075 kg CO2 per MJ of fuel combustion or a 70 percent reduction in emission over residual fuel oil. The bio-oil production life-cycle stage consumed 92 percent of the total cradle-to-grave energy requirements, while feedstock collection, preparation, and transportation consumed 4 percent each. This model provides a framework to better understand the major factors affecting greenhouse gas emissions related to bio-oil production and conversion to boiler fuel during fast pyrolysis.

Steele, Philip↗

Design Study for Bio-Oil Production from Biomass Using a Dual Fluidized-Bed Reactor

To evaluate the re-design and reconfiguration of a dual-fluidized bed (DFB) gasification system into a recirculating pyrolysis reactor, Computation Fluid Dynamic (CFD) simulations of the system were conducted. The Barracuda Virtual Reactor® computational particle fluid dynamic code was used to perform simulations of the pyrolysis process. Modeling of the chemical reaction kinetics for both gas phase and solid particle phase were included. The recirculating pyrolysis reactor shown in Fig. 1a is based on a bubbling-bed biomass pyrolyzer and a riser combustor to convert the remaining char. The operational differences in the re-configuration of the DFB gasification system into a recirculating pyrolysis system for the production of bio-oil are (1) replacement of a low-surface area inert bed material with a high-surface-area bed material that has acidic properties to provide catalytic activity for the production of bio-oil with reduced oxygen content, (2) lower temperature and residence time for bio-oil production from pyrolysis, (3) replacement of the fluidization gas in the bubbling bed pyrolyzer from steam to nitrogen, and (4) the reduction of pyrolyzer freeboard volume. The bed material used for catalytic pyrolysis is Sasol 300 (300-micron dia., bulk density 0.94 kg/l, and surface area 130 m2/g) and is a theta-alumina with mild acidity. This is in comparison with previous standard bed material Carbo HSP (430-micron dia., bulk density 2.01 kg/l, and surface area 0.03 m2/g) used for gasification. For bio-oil production, pyrolysis in the bubbling bed requires temperatures in the range of 550 C in comparison with gasification temperatures near 850 C. To attain this lower temperature requires management of the energy mass balances, with control of the bed material recirculation rate between bubbling bed pyrolyzer and riser combustor, the introduction of a nitrogen purge in the pyrolyzer, and adjusting the pressure balance between the two vessels. To extract bio-oil from the pyrolysis reactor with a snorkel, two different freeboard configurations were evaluated. In Fig. 1 b the existing high freeboard configuration is shown and in Fig. 1 c the reduced freeboard design is presented. The introduction of a nitrogen purge for the high free board configuration provided the highest bio-oil production from the CFD simulations. To decrease the bed-material circulation rate, primary and secondary air on the combustor side were reduced, and the pressure on the combustor was slightly increased. A portion of the biomass and bio-oil was observed to be transported to the combustor, leading to a smaller pyrolysis yield. The control of the pyrolyzer temperature is performed by controlling the circulation rate. Good fluidization of the bubbling bed and cascade PID control are required to keep the temperature from oscillating due to large time delay experienced when changing primary and secondary air. (a) (b) (c) Figure 1. (a) Dual Fluidized Bed pyrolysis system configuration, (b) mole fraction of nonpolar biooil in high freeboard configuration, and (c) mole fraction of nonpolar bio-oil in low freeboard configuration with nitrogen purge introduced in both configurations.

BASIC BIOLOGICAL SCIENCES,BIOMASS FUELS↗

Bio-optical profiling floats as new observational tools for biogeochemical and ecosystem studies: Potential synergies with ocean color remote sensing

Profiling floats now represent a mature technology. In parallel with their emergence, the field of miniature, low power bio-optical and biogeochemical sensors is rapidly evolving. Over recent years, the bio-geochemical and bio-optical community has begun to benefit from the increase in observational capacities by developing profiling floats that allow the measurement of key biooptical variables and subsequent products of biogeochemical and ecosystem relevance like Chlorophyll a (Chla), optical backscattering or attenuation coefficients which are proxies of Particulate Organic Carbon (POC), Colored Dissolved Organic Matter (CDOM). Thanks to recent algorithmic improvements, new bio-optical variables such as backscattering coefficient or absorption by CDOM, at present can also be extracted from space observations of ocean color. In the future, an intensification of in situ measurements by bio-optical profiling floats would permit the elaboration of unique 3D/4D bio-optical climatologies, linking surface (remotely detected) properties to their vertical distribution (measured by autonomous platforms), with which key questions in the role of the ocean in climate could be addressed. In this context, the objective of the IOCCG (International Ocean Color Coordinating Group) BIO-Argo working group is to elaborate recommendations in view of a future use of bio-optical profiling floats as part of a network that would include a global array that could be 'Argo-relevant', and specific arrays that would have more focused objectives or regional targets. The overall network, realizing true multi-scale sustained observations of global marine biogeochemistry and biooptics, should satisfy the requirements for validation of ocean color remote sensing as well as the needs of a wider community investigating the impact of global change on biogeochemical cycles and ecosystems. Regarding the global profiling float array, the recommendation is that Chla as well as POC should be the key variables to be systematically measured. A first target would be to implement 20% of the Argo floats with these measurements within a five-year term. The yearly additional cost is estimated to 1.5 M$, including additional management structure in each of the two Global Data Assembly Centers.

54 ENVIRONMENTAL SCIENCES↗

Contribution of acidic components to the total acid number (TAN) of bio-oil

Bio-oil or pyrolysis oil — a product of thermochemical decomposition of biomass under oxygen-limited conditions — holds great potential to be a substitute for nonrenewable fossil fuels. But, its high acidity, which is primarily due to the degradation of hemicelluloses, limits its applications. For the evaluation of bio-oil production and treatment, it is essential to accurately measure the acidity of bio-oil. The total acid number (TAN), which is defined as the amount of potassium hydroxide needed to titrate one gram of a sample and has been established as an ASTM method to measure the acidity of petroleum products, has been employed to investigate the acidity of bio-oil. The TAN values of different concentrations of bio-oil components such as standard solutions of acetic acid, propionic acid, vanillic acid, hydroxybenzoic acid, syringic acid, hydroxymethylfurfural, and phenol were analyzed according to the ASTM D664 standard method. Our method showed the same linear relationship between the TAN values and the molar concentrations of acetic, propionic, and hydroxybenzoic acids. A different linear relationship was found for vanillic acid, due to the presence of multiple functional groups that can contribute to the TAN value. Furthermore, the influence of the titration solvent on the TAN values has been determined by comparing the TAN values and titration curves obtained from the standard method with results from the TAN analysis in aqueous environment and with equilibrium modeling results. Aqueous bio-oil samples with a known amount of acetic acid added were also analyzed. The additional acetic acid in bio-oil samples caused a proportional increase in the TAN values. These results of this research indicate that the TAN value of a sample with acids acting as monoprotic acids in the titration solvent can be converted to the molar concentration of total acids. For a sample containing acids that act as diprotic and polyprotic acids, however, its TAN value cannot be simply converted to the molar concentration of total acids because these acids have a stronger contribution to the TAN values than the contribution of monoprotic acids.

09 BIOMASS FUELS↗

Analysis of switchgrass-derived bio-oil and associated aqueous phase generated in a semi-pilot scale auger pyrolyzer

To efficiently utilize water-soluble compounds in bio-oil and evaluate the potential effects of these compounds on processes such as microbial electrolysis, our study investigated the physico-chemical properties of bio-oil and the associated aqueous phase generated from switchgrass using a semi-pilot scale auger pyrolyzer. Combining separation and detection strategies with organic solvent extraction, an array of analytical instruments and methods were used to identify and quantify the chemical constituents. Separation of an aqueous phase from crude bio-oil was achieved by adding water (water: crude bio-oil at 4:1 in weight), which resulted in a partition of 61 wt.% of the organic compounds into a bio-oil aqueous phase (BOAP). GC/MS analysis for BOAP identified over 40 compounds of which 16 were quantified. Acetic acid, propionic acid, and levoglucosan are the major components in BOAP. In addition, a significant portion of chemicals that have the potential to be upgraded to hydrocarbon fuels were extracted to BOAP (77 wt.% of the alcohols, 61 wt.% of the furans, and 52 wt.% of the phenolic compounds in crude bio-oil). Valorization of the BOAP may require conversion methods capable of accommodating a very broad substrate specificity. Ultimately, a better separation strategy is needed to selectively remove the acidic and polar components from crude bio-oil to improve economic feasibility of biorefinery operations.

09 BIOMASS FUELS↗

MSU-Northern Bio-Energy Center of Excellence

The goal of this project was to establish the Bio-Energy Center (the Center) of Montana State University Northern (MSUN) as a Regional Research Center of Excellence in research, product development, and commercialization of non-food biomass for the bio-energy industry. A three-step approach, namely, (1) enhance the Center’s research and testing capabilities, (2) develop advanced biofuels from locally grown agricultural crops, and (3) educate the community through outreach programs for public understanding and acceptance of new technologies was identified to achieve this goal. The research activities aimed to address the obstacles concerning the production of biofuels and other bio-based fuel additives considering feedstock quality, conversion process, economic viability, and public awareness. First and foremost in enhancing the capabilities of the Center is the improvement of its laboratories and other physical facilities for investigating new biomass conversion technologies and the development of its manpower complement with expertise in chemistry, engineering, biology, and energy. MSUN renovated its Auto Diagnostics building and updated its mechanical and electrical systems necessary to house the state-of-the-art 525kW (704 hp) A/C Dynamometer. The newly renovated building was designated as the Advanced Fuels Building. Two laboratories, namely Biomass Conversion lab and Wet Chemistry lab were also added to the Center’s facilities. The Biomass Conversion lab was for research on the production of advanced biofuels including bio-jet fuel and bio-based fuel additives while the Wet Chemistry lab was used to conduct catalyst research. Necessary equipment and machines, such as gas chromatograph-mass spectrometry, were purchased and installed to help in research and testing. With the enhanced capabilities of the Center, research and testing activities were very much facilitated and more precise. New biofuels derived from Camelina sativa (camelina), a locally-grown oilseed crop was developed through a chemical process for converting the oil extracted into jet fuel. Promising methods of synthesizing heterogeneous metal complex catalyst that support the chemical conversion process were likewise developed. Breaking-down lignin to valuable chemicals using a metal complex catalyst was also investigated. Lignin is an organic polymer that binds around cellulose and hemicellulose fibers which strengthen cell walls in woody biomass. Test results showed promise and could lead to further exploration of using lignin for fuels and fuel additives. These findings could create another value-added product from lignin that can be sourced from beetle kill trees and product residues from cellulose ethanol plants. Coupled with these research discoveries was the provision of technical support to businesses in terms of product development and commercialization of bio-based products. This in turn opened new avenues for advancing the bio-energy industry in the region and helped support the regional agricultural-based economy through developing biofuels derived from feedstock that are grown locally. It assisted in developing biofuels that reduce exhaust emissions and improve engine performance.

09 BIOMASS FUELS↗

Standardization of chemical analytical techniques for pyrolysis bio-oil: history, challenges, and current status of methods

Here, we discuss the standardization of analytical techniques for pyrolysis bio-oils, including the current status of methods, and our opinions on future directions. First, the history of past standardization efforts is summarized, and both successful and unsuccessful validation of analytical techniques highlighted. The majority of analytical standardization studies to-date has tested only physical characterization techniques. In this paper, we present results from an international round robin on the validation of chemical characterization techniques for bio-oils. Techniques tested included acid number, carbonyl titrations using two different methods (one at room temperature and one at 80 °C), 31 P NMR for determination of hydroxyl groups, and a quantitative gas chromatography–mass spectrometry (GC-MS) method. Both carbonyl titration and acid number methods have yielded acceptable inter-laboratory variabilities. 31 P NMR produced acceptable results for aliphatic and phenolic hydroxyl groups, but not for carboxylic hydroxyl groups. As shown in previous round robins, GC-MS results were more variable. Reliable chemical characterization of bio-oils will enable upgrading research and allow for detailed comparisons of bio-oils produced at different facilities. Reliable analytics are also needed to enable an emerging bioenergy industry, as processing facilities often have different analytical needs and capabilities than research facilities. We feel that correlations in reliable characterizations of bio-oils will help strike a balance between research and industry, and will ultimately help to -determine metrics for bio-oil quality. Lastly, the standardization of additional analytical methods is needed, particularly for upgraded bio-oils.

09 BIOMASS FUELS↗

Quality Control in Fast Pyrolysis Bio-Oil Production and Use

This paper will focus on norms and standards for fast pyrolysis bio-oils. It will include the present status and address what still has to be done on bio-oil specifications and relevant test methods. The paper will address industrial needs in commercialization of the fuel oil use of bio-oil, including the registration application to the REACH program and its consequences within the European Union, as well as development of a standard within ASTM. The paper will discuss the most important properties of bio-oil and the variation in these properties among various bio-oils. It will address the issue of quality follow-up in bio-oil production, including the properties to be followed and the laboratory and on-line monitoring methods. The paper will provide a state of the art of fuel oil specifications, test methods, and testing procedures as they are applied to bio-oil. It will review the effort in support of the implementation of an ASTM standard including the methods validation work.

02 PETROLEUM↗

Assessing the hygrothermal performance of bio-based materials in building wall systems

Building envelope systems are crucial in regulating thermal and moisture exchange between interior and exterior environments, accounting for approximately 28 % of building energy consumption in the United States with walls being the primary contributors. Improper selection of building envelope materials can lead to moisture-related issues, reduced resilience, and compromised durability. Hygrothermal performance assessment is a key factor in efficient building design. As such, improving the energy and hygrothermal performance of opaque wall materials, through careful assessment of material choices, is essential to enhancing building resilience, lowering energy costs, and improving occupant comfort. As the building industry seeks new strategies to reduce material energy intensity, bio-based materials emerge as a promising solution. However, their long-term hygrothermal performance in building envelope systems remains underexplored. To fill this gap, this study evaluates the hygrothermal behavior of 13 bio-based materials in residential wall systems across three U.S. climate zones. Laboratory experiments were performed to measure material properties such as density, thermal conductivity, moisture transmission, and sorption isotherms. These data were integrated into the WUFI® simulation tool to assess wall hygrothermal performance in Houston, Baltimore, and Chicago. A three-phase modeling approach was used: (1) baseline residential walls with oriented strand board (OSB) and gypsum board; (2) replacing OSB with bio-based materials; and (3) replacing drywall with bio-based materials. Results showed that the evaluated bio-based materials maintained acceptable moisture thresholds of ≤ 16 % across all climates, confirming their viability as an alternative for current sheathing materials. Furthermore, this study provides a foundation for future research and innovation in material science on the use of certain bio-based materials in high-performance, low energy use residential construction. Ultimately, providing critical data, offering a database of bio-based material properties, and supplying a simulation-based approach will help designers make informed decisions for future efficient building practices.

Bio-based materials↗

A comprehensive state-of-technology review for upgrading bio-oil to renewable or blended hydrocarbon fuels

Bioenergy sources are being advanced as a meaningful environmental solution and a substitute for conventional energy sources. Bioenergy from biomass feedstocks currently comprises the largest portion of renewables in the United States. Thus, more effective process-level solutions can result in scaling-up biomass-derived energy production (e.g., biofuels). Pyrolysis, a thermochemical conversion technology, offers a commercially viable pathway to produce bio-oil from a wide range of biomass feedstocks (e.g., algae and terrestrial). Bio-oil requires further upgrading for producing final bio-products (e.g., transportation fuels and biochemicals). This article focuses on upgrading bio-oil to transportation fuels (liquid hydrocarbons), highlights the critical challenges of existing upgrading technologies, and identifies the potential research directions to meet the market needs. A comprehensive overview and classification of bio-oil upgrading pathways and their competencies are presented through both comparative and systematic literature reviews. It is concluded that the biofuel production cost is highly dependent on post-conversion pathways, particularly their hydrogenation and deoxygenation capacity. Thermochemical treatments are effective, but less cost-competitive due to the intensive process requirements (e.g., heat or pressure). Physicochemical treatments are less effective, however, they operate under mild process conditions and could be integrated with other treatments. Biochemical treatments are inadequate as a standalone process for upgrading bio-oil. It is further concluded that the electrochemical approach can be effective due to the retention of hydrogen from bio-oil water content during deoxygenation.

09 BIOMASS FUELS↗

Co-hydrotreatment of Bio-oil and Waste Cooking Oil to Produce Transportation Fuels

This paper reports the co-hydrotreatment of the heavy bio-oil fraction with waste cooking oil (WCO) using NiMo/γ-Al 2 O 3 catalyst, followed by the distillation of resulting deoxygenated oil and the characterization of resulting fuel cuts. The heavy BTG bio-oil fraction was obtained by removing the very reactive light-oxygenated compounds via rotary evaporation, subsequently mixed with 1-butanol. The resulting oil was blended with WCO and subjected to a two-step co-hydrotreatment process. The first step, called “stabilization,” is aimed at saturating highly reactive hydrogen-deficient compounds. The second step, called “deoxygenation,” aimed to remove bio-oil oxygen, primarily as H 2 O. This study examined the impact of varying bio-oil concentrations (0, 10, 20, 30, 40 wt.% of WCO) on the upgraded oil's yield, composition, and fuel properties. The resulting hydrotreated oil was distilled into gasoline-range, kerosene-range, and diesel-range hydrocarbons at <150 °C, 150 to 250 °C, and 250 to 350 °C, respectively. The yield of the hydrotreated oil indicates that as the bio-oil concentration increases, the amounts of coke (0.7 to 2.4 %) and water (2 to 10 wt. %) increase while the organic layer yields decrease (80 to 63 %). The coke yield was comparable to the coke yield obtained when co-processing the pyrolytic lignin fraction. This suggests that coke is formed from both the sugar oligomers and the lignin-derived oligomers. The UV-fluorescence analysis on the hydrotreated oil shows that more polycondensed and conjugated ring compounds formed as the bio-oil concentration is increased. These compounds are precursors of coke. FTIR results showed that most raw materials were converted to biofuels after the hydrotreatment. To achieve less than 1 wt. % of coke yield, blends with up to 20 wt. % pyrolysis oil should be used. An increase in bio-oil concentration leads to a slight increase in gasoline yield and a decrease in kerosene and diesel yields. The identified carbon species found in the fuel cuts include n-paraffin, iso-paraffin, cycloparaffin, and aromatics. Further, the jet fuel cut (kerosene) was characterized by density, surface tension, and viscosity. Our product conforms to the standard specifications for sustainable aviation fuels (Jet A-1). Further research is suggested to fine-tune the operating parameters for achieving reduced coke yield and enhanced kerosene yield.

09 BIOMASS FUELS↗

Methods and Challenges in the Determination of Molecular Weight Metrics of Bio-oils

The analyses of thermochemically-derived bio-oil properties and composition are challenging due to the diversity of compounds present and the reactivity of the oils. There are currently a variety of techniques used and no standard method established for the analysis of the molecular weight distribution, weight average molecular weight (Mw) and other molecular weight metrics of bio-oils. This review focuses on the challenges and variation in methodologies employed for the analysis of bio-oils on the basis of molecular weight, particularly by gel permeation chromatography (GPC). GPC is the most practical means for determination of molecular weight metrics of bio-oils but needs to be refined using appropriate standards and/or detectors to ensure consistency and accurate quantification of molecular weight metrics. Future method development for a robust technique with accurate and comparable molecular weight data should focus on GPC with multiple detection methodology on whole bio-oils, verified relative to another technique such as mass spectrometry (MS). MS techniques, such as Fourier transform-ion cyclotron resonance (FT-ICR MS), have also been utilized for the determination of molecular weight distribution of bio-oils and are briefly addressed in this review. Many MS methods can provide extensive characterization and structural speciation of components in bio-oils, and while accurate molecular weight metrics can be obtained with the appropriate use of ionization techniques and optimized parameters to ensure appropriate range of m/z and signals representative of abundance, MS is not a robust or an economically practical method for routine molecular weight analyses. Physical separation techniques such as preparative scale GPC, distillation, and liquid-liquid extraction methods are also briefly addressed in this review in the context of molecular weight analyses.

09 BIOMASS FUELS↗

Accelerated Aging of Fast Pyrolysis Bio-Oil Using Carbonyl Titration: Laboratory Analytical Procedure (LAP)

This laboratory analytical procedure covers the accelerated aging of fast pyrolysis bio-oils. Bio-oils undergo reactions that result in physical and chemical changes over time. These changes typically result in an increase in molecular weight, decrease in some functional groups such as carbonyls, and an increase in viscosity; additionally, the aging process often leads to phase separation. Studies have shown that accelerated aging of bio-oils using this method closely mimics room temperature aging for long periods of time (over 3 years). This procedure has been developed for the accelerated aging of fast pyrolysis bio-oils only. Fast pyrolysis bio-oils are more reactive than other bio-oils (e.g., catalytic fast pyrolysis) and undergo aging much more rapidly. Therefore, this procedure should only be used for fast pyrolysis bio-oil samples.

09 BIOMASS FUELS↗

Greenhouse Gas Impact of Algal Bio-Crude Production for a Range of CO2 Supply Scenarios

Refined bio-crude production from hydrothermal liquefaction of algae holds the potential to replace fossil-based conventional liquid fuels. The microalgae act as natural carbon sequestrators by consuming CO2. However, this absorbed CO2 is released to the atmosphere during the combustion of the bio-crude. Thus, the life-cycle greenhouse gas (GHG) emissions of refined bio-crude are linked to the production and supply of the materials involved and the process energy demands. One prominent raw material is CO2, which is the main source of carbon for algae and the subsequent products. The emissions associated with the supply of CO2 can have a considerable impact on the sustainability of the algae-based refined bio-crude production process. Furthermore, the diurnal algae growth cycle complicates the CO2 supply scenarios. Traditionally, studies have relied on CO2 supplied from existing power plants. However, there is potential for building natural gas or biomass-based power plants with the primary aim of supplying CO2 to the biorefinery. Alternately, a direct air capture (DAC) process can extract CO2 directly from the air. The life-cycle GHG emissions associated with the production of refined bio-crude through hydrothermal liquefaction of algae are presented in this study. Different CO2 supply scenarios, including existing fossil fuel power plants and purpose-built CO2 sources, are compared. The integration of the CO2 sources with the algal biorefinery is also presented. The CO2 supply from biomass-based power plants has the highest potential for GHG reduction, with a GHG footprint of −57 g CO2 eq./MJ refined bio-crude. The CO2 supply from the DAC process has a GHG footprint of 49 CO2 eq./MJ refined bio-crude, which is very similar to the scenario that considers the supply of CO2 from an existing conventional natural gas-based plant and takes credit for the carbon utilization.

36 MATERIALS SCIENCE↗

Long-Term Corrosion Studies of Pine Derived Bio-Oil and Blends with Heavy Fuel Oil

Biomass derived liquid fuels offer a means to reduce greenhouse gas emissions compared to those produced by combustion of petroleum derived liquid fuels. However, the corrosivity of bio-oils toward the less expensive structural materials creates a material selection problem for designers of storage tanks and combustion systems. Samples of candidate structural materials are being exposed for thousands of hours in multiple fast pyrolysis bio-oils and conditions to evaluate the corrosion resistance of these materials. One method to mitigate the corrosivity of bio-oils and speed their adoption, while also decreasing the pollution issues associated with low quality petroleum derived fuels, is to utilize blends of bio-oil and heavy fuel oil in engines currently solely burning a petroleum-based fuel. In addition to the corrosion studies conducted in 100% bio-oil, studies were also conducted with blends of the fast pyrolysis bio-oil produced from pine tree components with a heavy fuel oil that is used in ocean-going ships. This bio-oil had a very high carboxylic acid content which made it very corrosive to carbon and 2¼ Cr-1 Mo steel and even 409 stainless steel. The heavy fuel oil was not corrosive to carbon steel, but its sulfur content makes it a significant pollution producer and particularly undesirable for use near coastlines. Corrosion tests were conducted with the individual components and with various blends of the two liquid fuels. Studies showed a significantly lower corrosivity of the blends than would be projected assuming linear mixing behavior. Adoption of such blends holds the potential to reduce production of sulfur-containing exhaust gases as well as carbon dioxide from non-renewable fuels.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Novel Electro-Deoxygenation Process for Bio-oil Upgrading

Biomass is a potential source of renewable fuel. Bio-oil produced by fast pyrolysis is a prospective option to replace fossil fuels for transportation. However, bio-oil needs to be upgraded to remove its high oxygen and water content, and acidity to produce useful fuels. The upgrading of bio-oil is generally accomplished by hydrodeoxygenation (HDO) using hydrogen. The instability of bio-oil poses a major challenge in transportation to central upgrading facility. An electro-deoxygenation (EDOx) process was evaluated to fully or partially deoxygenate bio-oil using solid oxide electrolysis process. This device uses an oxygen ion conducting membrane which under an applied electric potential removes oxygen in the form of an ion and transports it to the opposite side of the membrane where it is released as oxygen molecule. When water is present in the bio-oil vapor, the process generates in situ hydrogen to facilitate deoxygenation over the electrode that functions as catalyst.

09 BIOMASS FUELS↗