Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Approximate dynamic programming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

The Importance of Detailed Component Simulations in the Feedsystem Development for a Two-Stage-to Orbit Reusable Launch Vehicle

To meet the requirements for the 2nd Generation Reusable Launch Vehicle (RLV), a unique propulsion feed system concept was identified using crossfeed between the booster and orbiter stages that could reduce the Two-Stage-to-Orbit (TSTO) vehicle weight and development cost by approximately 25%. A Main Propulsion System (MPS) crossfeed water demonstration test program was configured to address all the activities required to reduce the risks for the MPS crossfeed system. A transient, one-dimensional system simulation was developed for the subscale crossfeed water flow tests. To ensure accurate representation of the crossfeed valve's dynamics in the system model, a high-fidelity, three-dimensional, computational fluid-dynamics (CFD) model was employed. The results from the CFD model were used to specify the valve's flow characteristics in the system simulation. This yielded a crossfeed system model that was anchored to the specific valve hardware and achieved good agreement with the measured test data. These results allowed the transient models to be correlated and validated and used for full scale mission predictions. The full scale model simulations indicate crossfeed is ' viable with the system pressure disturbances at the crossfeed transition being less than experienced by the propulsion system during engine start and shutdown transients.

Mazurkivich, Pete↗
NASA NTRS1976

Control methods for aiding a pilot during STOL engine failure transients

Candidate autopilot control laws that control the engine failure transient sink rates by demonstrating the engineering application of modern state variable control theory were defined. The results of approximate modal analysis were compared to those derived from full state analyses provided from computer design solutions. The aircraft was described, and a state variable model of its longitudinal dynamic motion due to engine and control variations was defined. The classical fast and slow modes were assumed to be sufficiently different to define reduced order approximations of the aircraft motion amendable to hand analysis control definition methods. The original state equations of motion were also applied to a large scale state variable control design program, in particular OPTSYS. The resulting control laws were compared with respect to their relative responses, ease of application, and meeting the desired performance objectives.

Nelson, E. R.↗
NASA NTRS1978

User's guide to computer programs JET 5A and CIVM-JET 5B to calculate the large elastic-plastic dynamically-induced deformations of multilayer partial and/or complete structural rings

These structural ring deflections lie essentially in one plane and, hence, are called two-dimensional (2-d). The structural rings may be complete or partial; the former may be regarded as representing a fragment containment ring while the latter may be viewed as a 2-d fragment-deflector structure. These two types of rings may be either free or supported in various ways (pinned-fixed, locally clamped, elastic-foundation supported, mounting-bracket supported, etc.). The initial geometry of each ring may be circular or arbitrarily curved; uniform-thickness or variable-thickness rings may be analyzed. Strain-hardening and strain-rate effects of initially-isotropic material are taken into account. An approximate analysis utilizing kinetic energy and momentum conservation relations is used to predict the after-impact velocities of each fragment and of the impact-affected region of the ring; this procedure is termed the collision-imparted velocity method (CIVM) and is used in the CIVM-JET 5 B program. This imparted-velocity information is used in conjunction with a finite-element structural response computation code to predict the transient, large-deflection, elastic-plastic responses of the ring. Similarly, the equations of motion of each fragment are solved in small steps in time. Provisions are made in the CIVM-JET 5B code to analyze structural ring response to impact attack by from 1 to 3 fragments, each with its own size, mass, translational velocity components, and rotational velocity. The effects of friction between each fragment and the impacted ring are included.

Wu, R. W. H.↗
NASA NTRS1973

The constraint method: A new finite element technique

An approch to the finite element method which utilizes families of conforming finite elements based on complete polynomials is presented. Finite element approximations based on this method converge with respect to progressively reduced element sizes as well as with respect to progressively increasing orders of approximation. Numerical results of static and dynamic applications of plates are presented to demonstrate the efficiency of the method. Comparisons are made with plate elements in NASTRAN and the high-precision plate element developed by Cowper and his co-workers. Some considerations are given to implementation of the constraint method into general purpose computer programs such as NASTRAN.

Tsai, C.↗
NASA NTRS1986

Multitasking the code ARC3D

The CRAY multitasking system was developed in order to utilize all four processors and sharply reduce the wall clock run time. This paper describes the techniques used to modify the computational fluid dynamics code ARC3D for this run and analyzes the achieved speedup. The ARC3D code solves either the Euler or thin-layer N-S equations using an implicit approximate factorization scheme. Results indicate that multitask processing can be used to achieve wall clock speedup factors of over three times, depending on the nature of the program code being used. Multitasking appears to be particularly advantageous for large-memory problems running on multiple CPU computers.

Barton, John T.↗
NASA NTRS2012

Landsat Science: 40 Years of Innovation and Opportunity

Landsat satellites have provided unparalleled Earth-observing data for nearly 40 years, allowing scientists to describe, monitor and model the global environment during a period of time that has seen dramatic changes in population growth, land use, and climate. The success of the Landsat program can be attributed to well-designed instrument specifications, astute engineering, comprehensive global acquisition and calibration strategies, and innovative scientists who have developed analytical techniques and applications to address a wide range of needs at local to global scales (e.g., crop production, water resource management, human health and environmental quality, urbanization, deforestation and biodiversity). Early Landsat contributions included inventories of natural resources and land cover classification maps, which were initially prepared by a visual interpretation of Landsat imagery. Over time, advances in computer technology facilitated the development of sophisticated image processing algorithms and complex ecosystem modeling, enabling scientists to create accurate, reproducible, and more realistic simulations of biogeochemical processes (e.g., plant production and ecosystem dynamics). Today, the Landsat data archive is freely available for download through the USGS, creating new opportunities for scientists to generate global image datasets, develop new change detection algorithms, and provide products in support of operational programs such as Reducing Emissions from Deforestation and Forest Degradation in Developing Countries (REDD). In particular, the use of dense (approximately annual) time series to characterize both rapid and progressive landscape change has yielded new insights into how the land environment is responding to anthropogenic and natural pressures. The launch of the Landsat Data Continuity Mission (LDCM) satellite in 2012 will continue to propel innovative Landsat science.

Cook, Bruce D.↗
NASA NTRS1985

Computational fluid dynamics at NASA Ames and the numerical aerodynamic simulation program

Computers are playing an increasingly important role in the field of aerodynamics such as that they now serve as a major complement to wind tunnels in aerospace research and development. Factors pacing advances in computational aerodynamics are identified, including the amount of computational power required to take the next major step in the discipline. The four main areas of computational aerodynamics research at NASA Ames Research Center which are directed toward extending the state of the art are identified and discussed. Example results obtained from approximate forms of the governing equations are presented and discussed, both in the context of levels of computer power required and the degree to which they either further the frontiers of research or apply to programs of practical importance. Finally, the Numerical Aerodynamic Simulation Program--with its 1988 target of achieving a sustained computational rate of 1 billion floating-point operations per second--is discussed in terms of its goals, status, and its projected effect on the future of computational aerodynamics.

Peterson, V. L.↗
NASA NTRS1977

Navigation simulator for the Space Tug vehicle

A general simulation program (GSP) for state estimation of a nonlinear space vehicle flight navigation system is developed and used as a basis for evaluating the performance of a Space Tug navigation system. An explanation of the iterative guidance mode (IGM) guidance law, derivation of the dynamics, coordinate frames and state estimation routines are given in order to clarify the assumptions and approximations made. A number of simulation and analytical studies are used to demonstrate the operation of the Tug system. Included in the simulation studies are (1) initial offset vector parameter study; (2) propagation time vs accuracy; (3) measurement noise parametric study and (4) reduction in computational burden of an on-board implementable scheme. From the results of these studies, conclusions and recommendations concerning future areas of practical and theoretical work are presented.

Colburn, B. K.↗
NASA NTRS2002

A Physics Exploratory Experiment on Plasma Liner Formation

Momentum flux for imploding a target plasma in magnetized target fusion (MTF) may be delivered by an array of plasma guns launching plasma jets that would merge to form an imploding plasma shell (liner). In this paper, we examine what would be a worthwhile experiment to do in order to explore the dynamics of merging plasma jets to form a plasma liner as a first step in establishing an experimental database for plasma-jets driven magnetized target fusion (PJETS-MTF). Using past experience in fusion energy research as a model, we envisage a four-phase program to advance the art of PJETS-MTF to fusion breakeven Q is approximately 1). The experiment (PLX (Plasma Liner Physics Exploratory Experiment)) described in this paper serves as Phase I of this four-phase program. The logic underlying the selection of the experimental parameters is presented. The experiment consists of using twelve plasma guns arranged in a circle, launching plasma jets towards the center of a vacuum chamber. The velocity of the plasma jets chosen is 200 km/s, and each jet is to carry a mass of 0.2 mg - 0.4 mg. A candidate plasma accelerator for launching these jets consists of a coaxial plasma gun of the Marshall type.

Thio, Y. C. Francis↗
NASA NTRS2000

Determination of anionic surfactants during wastewater recycling process by ion pair chromatography with suppressed conductivity detection

A direct approach utilizing ion pairing reversed-phase chromatography coupled with suppressed conductivity detection was developed to monitor biodegradation of anionic surfactants during wastewater recycling through hydroponic plant growth systems and fixed-film bioreactors. Samples of hydroponic nutrient solution and bioreactor effluent with high concentrations (up to 120 mS electrical conductance) of inorganic ions can be analyzed without pretreatment or interference. The presence of non-ionic surfactants did not significantly affect the analysis. Dynamic linear ranges for tested surfactants [Igepon TC-42, ammonium lauryl sulfate, sodium laureth sulfate and sodium alkyl (C10-C16) ether sulfate] were 2 to approximately 500, 1 to approximately 500, 2.5 to approximately 550 and 3.0 to approximately 630 microg/ml, respectively.

NASA Program Advanced Human Support Technology↗
NASA NTRS1972

Riding and handling qualities of light aircraft: A review and analysis

Design procedures and supporting data necessary for configuring light aircraft to obtain desired responses to pilot commands and gusts are presented. The procedures employ specializations of modern military and jet transport practice where these provide an improvement over earlier practice. General criteria for riding and handling qualities are discussed in terms of the airframe dynamics. Methods available in the literature for calculating the coefficients required for a linearized analysis of the airframe dynamics are reviewed in detail. The review also treats the relation of spin and stall to airframe geometry. Root locus analysis is used to indicate the sensitivity of airframe dynamics to variations in individual stability derivatives and to variations in geometric parameters. Computer programs are given for finding the frequencies, damping ratios, and time constants of all rigid body modes and for generating time histories of aircraft motions in response to control inputs. Appendices are included presenting the derivation of the linearized equations of motion; the stability derivatives; the transfer functions; approximate solutions for the frequency, damping ratio, and time constants; an indication of methods to be used when linear analysis is inadequate; sample calculations; and an explanation of the use of root locus diagrams and Bode plots.

Smetana, F. O.↗
NASA NTRS1988

Heavy hydrocarbon main injector technology

One of the key components of the Advanced Launch System (ALS) is a large liquid rocket, booster engine. To keep the overall vehicle size and cost down, this engine will probably use liquid oxygen (LOX) and a heavy hydrocarbon, such as RP-1, as propellants and operate at relatively high chamber pressures to increase overall performance. A technology program (Heavy Hydrocarbon Main Injector Technology) is being studied. The main objective of this effort is to develop a logic plan and supporting experimental data base to reduce the risk of developing a large scale (approximately 750,000 lb thrust), high performance main injector system. The overall approach and program plan, from initial analyses to large scale, two dimensional combustor design and test, and the current status of the program are discussed. Progress includes performance and stability analyses, cold flow tests of injector model, design and fabrication of subscale injectors and calorimeter combustors for performance, heat transfer, and dynamic stability tests, and preparation of hot fire test plans. Related, current, high pressure, LOX/RP-1 injector technology efforts are also briefly discussed.

Fisher, S. C.↗
NASA NTRS1993

Dust and ionized gas in elliptical galaxies: Signatures of merging collisions

Traditionally elliptical galaxies were thought to be essentially devoid of interstellar matter. However, recent advances in instrumental sensitivity have caused a renaissance of interest in dust and gas in - or associated with - elliptical galaxies. In particular, the technique of co-adding IRAS survey scans has led to the detection of more than half of all ellipticals with BT less than 11 mag. in the Revised Shapley-Ames catalog, indicating the presence of 10(exp 7) - 10(exp 8) solar mass of cold interstellar matter (Jura et al. 1987). In addition, CCD multi-color surface photometry shows dust patches in about 30 percent of the cases studied to date (e.g., Veron-Cetty & Veron 1988). Thorough study of the gas and dust in ellipticals is important to (1) determine its origin (mass-loss from late-type stars, merging collisions with other galaxies or accretion inflows from cooling X-ray gas), and (2) investigate the 3-D shape of ellipticals, as can be derived from the orientation of the dust lanes and the 2-D velocity field of the gas. An important result of our comprehensive CCD imaging program is that a relevant fraction (approximately 40 percent) of the sample objects exhibits dust patches within extended H-alpha+(NII) line-emitting filaments. This common occurrence can be easily accounted for if the dust and gas have an external origin, i.e., mergers or interactions with gas-rich galaxies. Evidence supporting this suggestion: (1) the ionized gas is usually dynamically decoupled from the stellar velocity field (see, e.g., Sharples et al. 1983, Bertola & Bettoni 1988); (2) it is shown in a companion paper (Goudfrooij et al. 1992) that internal stellar mass loss alone can not account for the dust content of elliptical galaxies.

Goudfrooij, Paul↗
NASA NTRS1980

First Scientific Working Group Meeting of Airborne Doppler Lidar Wind Velocity Measurement Program

The purpose of the first scientific working group meeting was fourfold: (1) to identify flight test options for engineering verification of the MSFC Doppler Lidar; (2) to identify flight test options for gathering data for scientific/technology applications; (3) to identify additional support equipment needed on the CV 990 aircraft for the flight tests; and (4) to identify postflight data processing and data sets requirements. The working group identified approximately ten flight options for gathering data on atmospheric dynamics processes, including turbulence, valley breezes, and thunderstorm cloud anvil and cold air outflow dynamics. These test options will be used as a basis for planning the fiscal year 1981 tests of the Doppler Lidar system.

Kaufman, J. W.↗
NASA NTRS1980

AD-1 oblique wing aircraft program

The oblique wing concept for super- and subsonic transport was assessed by analysis and wind tunnel radio control model and remotely piloted vehicle testing. A one-sixth scale wind tunnel model and a low speed manned oblique wing research airplane (AD-1) were developed. Model wind tunnel test data on dynamic structural response characteristics were used in a simulator to develop the control system. The airplane is of simple design with fiber glass skin, weight of approximately 2100 lbs and speeds of up to 175 knots at altitudes up to 15,000 ft. Flight testing will investigate handling and flying qualities, oblique wing flight control characteristics, aeroelastic wing design and will compare actual with predicted aerodynamic characteristics. Nineteen flights were made at 12,000 to 13,000 feet with speeds of 100-160 knots. Flutter clearance as a function of wing sweep angle is now under investigation.

Andrews, W. H.↗
NASA NTRS1983

Structural optimization with dynamic behavior constraints

The minimum weight optimum design of damped linearly elastic structural systems subjected to periodic loading with behavior constraints on maximum deflections and side constraints on design variables is addressed. Attention is focused on the two major impediments to an optimal solution: (1) the time parametric nature of the behavior constraints; and (2) the severe nonconvexity of the design space. A solution method based on upper bound approximations for the behavior constraints and an innovative mathematical programming scheme for seeking the optimal frequency subspace is set forth. Numerical results for several test problems illustrate the effectiveness of the method reported.

Mills-Curran, W. C.↗
NASA NTRS1977

Variants and extensions of a fast direct numerical cauchy-riemann solver, with illustrative applications

Revised and extended versions of a fast, direct (noniterative) numerical Cauchy-Riemann solver are presented for solving finite difference approximations of first order systems of partial differential equations. Although the difference operators treated are linear and elliptic, one significant application of these extended direct Cauchy-Riemann solvers is in the fast, semidirect (iterative) solution of fluid dynamic problems governed by the nonlinear mixed elliptic-hyperbolic equations of transonic flow. Different versions of the algorithms are derived and the corresponding FORTRAN computer programs for a simple example problem are described and listed. The algorithms are demonstrated to be efficient and accurate.

Martin, E. D.↗
NASA NTRS1978

Identification of the stability parameters of an aeroelastic airplane

The problem of the parameter identification of large scale dynamic systems involving a system matrix characterized by approximately 200 elements is addressed. By using phase variable transformations, a mathematical model of an aeroelastic airplane is described in a form that is amenable to partial or piecemeal acceptance of parameters estimated from flight data. A mathematical model of the U.S. Air Force Total In-Flight Simulator was computed using the FLEXSTAB digital computer program. As data became available during the progress of the flight test program, this data was processed and substituted in the mathematical model for parameters analytically obtained from the FLEXSTAB program. The results tend to show a progressive and orderly transition from an analytically defined mathematical model to one obtained from the flight tests of the actual aircraft.

Rynaski, E. G.↗