Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Al2O3”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Vacuum ultraviolet thin films. I - Optical constants of BaF2, CaF2, LaF3, MgF2, Al2O3, HfO2, and SiO2 thin films. II - Vacuum ultraviolet all-dielectric narrowband filters

An iteration process matching calculated and measured reflectance and transmittance values in the 120-230 nm VUV region is presently used to ascertain the optical constants of bulk MgF2, as well as films of BaF2, CaF2, LaF3, MgF2, Al2O3, HfO2, and SiO2 deposited on MgF2 substrates. In the second part of this work, a design concept is demonstrated for two filters, employing rapidly changing extinction coefficients, centered at 135 nm for BaF2 and 141 nm for SiO2. These filters are shown to yield excellent narrowband spectral performance in combination with narrowband reflection filters.

Zukic, Muamer↗
NASA NTRS1989

Thermal expansion and elastic anisotropy in single crystal Al2O3 and SiC whiskers

The crystalline thermal expansion and elastic anisotropies of SiC and Al2O3 whiskers are considered in the process of evaluation of the anisotropy of the alpha-E product, the thermoelastic stress index. It is demonstrated to exhibit considerable crystalline anisotropy and a substantial temperature dependence, both of which will influence the thermal and residual stresses in composites using these materials for reinforcement.

Salem, J. A.↗
NASA NTRS1991

Al-26 and O-16 in the early solar system - Clues from meteoritic Al2O3

The study focuses on 26 Al2O3 grains up to 20 micron in size recovered from the Murchison C2 chrondite. It is observed that Mg-26/Mg-24 ranges up to 56 times the solar system ratio, but the initial Al-26/Al-27 ratios do not exceed the canonical maximum of 0.00005 in other meteoritic samples. It is concluded that this ratio represents the abundance of live Al-26 in the early solar system, not fossil radiogenic Mg-26 surviving from presolar times. The grains are shown to divide into three groups on the basis of Al-26, O-16, Ti, and V content, and distinctive correlations are found for Al-26 and O-16. An origin from at least three discrete components is suggested, two of which contained live Al-26.

Anders, Edward↗
NASA NTRS1992

Tribological evaluation of an Al2O3-SiO2 ceramic fiber candidate for high temperature sliding seals

A test program to determine the relative sliding durability of an alumina-silica candidate ceramic fiber for high temperature sliding seal applications as described. This work represents the first reporting of the sliding durability of this material system. Pin-on-disk tests were used to evaluate the potential seal material by sliding a tow or bundle of the candidate ceramic fiber against a superalloy test disk. Friction was measured during the tests and fiber wear, indicated by the extent of fibers broken in the tow or bundle, was measured at the end of each test. Test variables studied included ambient temperatures from 25 C to 900 C, loads from 1.3 to 21.2 Newtons, and sliding velocities from 0.025 to 0.25 m/sec. In addition, the effects of fiber diameter, elastic modulus, and a pretest fiber heat treatment on friction and wear were measured. In most cases, wear increased with temperature. Friction ranged from about 0.36 at 500 C and low velocity (0.025 m/s) to over 1.1 at 900 C and high velocity (0.25 m/s). The pretest fiber heat treatment, which caused significant durability reductions for alumina-boria-silica ceramic fibers tested previously, had little effect on the alumina-silica fibers tested here. These results indicate that the alumina-silica (Al2O3-SiO2) fiber is a good candidate material system for high temperature sliding seal applications.

Dellacorte, Christopher↗
NASA NTRS1993

Effect of thermal cycling on interface bonding requirements in Al2O3 fiber-reinforced superalloy composites

CTE (coefficient of thermal expansion) mismatch-induced stresses as they affect the fiber-matrix bond integrity of Al2O3 fiber-reinforced superalloy composites are examined. Of the three individual stress components, only the radial stress directly affects the integrity of the fiber-matrix interface. It is noted that a compressive radial stress leads to a clamping action on the fiber and is therefore beneficial to the integrity of the fiber-matrix bond. A radial tensile stress, on the other hand, can cause debonding of the fiber from the matrix for a weak fiber-matrix bond.

Misra, Ajay K.↗
NASA NTRS1994

Development of lasers optimized for pumping Ti:Al2O3 lasers

Laboratory demonstrations that were completed included: (1) an all-solid-state, broadly tunable, single-frequency, Ti:Al2O3 master oscillator, and (2) a technique for obtaining 'long' (nominally 100- to 200-ns FWHM) laser pulses from a Q-switched, Nd oscillator at energy levels commensurate with straightforward amplification to the joule level. A diode-laser-pumped, Nd:YLF laser with intracavity SHG was designed, constructed, and evaluated. With this laser greater than 0.9 W of CW, output power at 523.5 nm with 10 W of diode-laser pump power delivered to the Nd:YLF crystal was obtained. With this laser as a pump source, for the first time, to our knowledge, an all solid-state, single frequency, Ti:Al203 laser with sufficient output power to injection seed a high-energy oscillator over a 20-nm bandwidth was demonstrated. The pulsed laser work succeeded in demonstrating pulse-stretching in a Q-switched Nd:YAG oscillator. Pulse energies greater than 50-mJ were obtained in pulses with 100- to 200-ns pulsewidths (FWHM).

Rines, Glen A.↗
NASA NTRS1994

Mg and Ti isotopes in presolar Al2O3

Oxygen isotopic compositions and initial Al-26/Al-27 ratios were reported for two presolar Al2O3 grains, Orgueil B and Bishunpur B39. In Orgueil B, O-17/O-16 is about twice the solar value but O-18/O-16 is normal. In B39, O-17/O-16 is approximately 7x higher than solar and O-18/O-16 is 0.6x the solar value. Spectroscopic observations of red giant stars show similar O compositions, which result when material that has experienced partial H burning is mixed into the stellar envelope by the first dredge-up. The O-17/O-16 ratios indicate that Orgueil B originated around a star of approximately 1.5 solar mass, while B39 formed around either a approximately 2 solar mass or 4-7 solar mass star. Both grains formed with Al-26/Al-27 ratios of approximately 10(exp -3). Aluminum-26 is produced in the H shell after core H burning has ceased and first dredge-up has occurred. It is spread through the envelope by the third dredge-up, which occurs in low- and intermediate-mass stars as a series of mixing events driven by thermal pulses in the He shell. In intermediate-mass stars (3-8 solar mass), Al-26 can also be brought to the surface by the second dredge-up, which occurs at the end of core He burning. We have measured Ti isotopes by ion probe in Orgueil B and Bishunpur B39, looking for evidence of He-shell nucleosynthesis. Stars of approximately 1.5 solar mass do not experience second dredge-up, so the Al-26 in Orgueil B must have been mixed outward during third dredge-up, which also supplies He-shell material to the envelope. The size of the isotopic shifts in Ti and Mg suggest that Orgueil B contains approximately 5-10x more material from the He-shell than from the H-shell. In contrast, the lack of measurable Mg and Ti anomalies in B39 imply little or no He-shell contribution. This indicates that Al-26 in B39 was supplied by second dredge-up prior to He-shell ignition and points to a parent star of 4-7 solar mass.

Huss, G. R.↗
NASA NTRS1994

Tribological evaluation of an Al2O3-SiO2 ceramic fiber candidate for high temperature sliding seals

A test program to determine the relative sliding durability of an alumina-silica candidate ceramic fiber for high temperature sliding seal applications is described. Pin-on-disk tests were used to evaluate the potential seal material by sliding a tow or bundle of the candidate ceramic fiber against a superalloy test disk. Friction was measured during the tests and fiber wear, indicated by the extent of fibers broken in the tow or bundle, was measured at the end of each test. Test variables studied included ambient temperatures from 25 to 900 C, loads from 1.3 to 21.2 N, and sliding velocities from 0.025 to 0.25 m/sec. In addition, the effects of fiber diameter and elastic modulus on friction and wear were measured. Thin gold films deposited on the superalloy disk surface were evaluated in an effort to reduce friction and wear of the fibers. In most cases, wear increased with test temperature. Friction ranged from 0.36 at 500 C and low velocity (0.025 m/sec) to over 1.1 at 900 C and high velocity (0.25 m/sec). The gold films resulted in satisfactory lubrication of the fibers at 25 C. At elevated temperatures diffusion of substrate elements degraded the films. These results indicate that the alumina-silica (Al2O3-SiO2) fiber is a good candidate material system for high temperature sliding seal applications. More work is needed to reduce friction.

Dellacorte, Christopher↗
NASA NTRS1997

Time/Temperature Dependent Tensile Strength of SiC and Al2O3-Based Fibers

In order to understand and model the thermomechanical behavior of fiber-reinforced composites, stress-rupture, fast-fracture, and warm-up rupture studies were conducted on various advanced SiC and Al2O3-based fibers in the,temperature range from 20 to 1400 C in air as well as in inert environments. The measured stress-rupture, fast fracture, and warm-up rupture strengths were correlated into a single master time/temperature-dependent strength plot for each fiber type using thermal activation and slow crack growth theories. It is shown that these plots are useful for comparing and selecting fibers for CMC and MMC reinforcement and that, in comparison to stress rupture tests, the fast-fracture and warm-up tests can be used for rapid generation of these plots.

Yun, Hee Mann↗
NASA NTRS1998

MgO-Al2O3-ZrO2 Amorphous Ternary Composite: A Dense and Stable Optical Coating

The process-parameter-dependent optical and structural properties of MgO-Al2O3-ZrO2 ternary mixed-composite material were investigated. Optical properties were derived from spectrophotometric measurements. The surface morphology, grain size distributions, crystallographic phases, and process- dependent material composition of films were investigated through the use of atomic force microscopy, x-ray diffraction analysis, and energy-dispersive x-ray analysis. Energy-dispersive x-ray analysis made evident the correlation between the optical constants and the process-dependent compositions in the films. It is possible to achieve environmentally stable amorphous films with high packing density under certain optimized process conditions.

Shaoo, Naba K.↗
NASA NTRS2000

The Effects of Gravity on the Combustion Synthesis of B2O3-Al2O3-MgO Glass Ceramic Composites

Glass ceramic composites based on B2O3-Al2O3-MgO have been produced by combustion synthesis in a Self-propagating mode. The gravitational effects on the combustion characteristics such as combustion wave velocity (V), and combustion temperature (T(sub c)) were studied. The results showed that the gravitational effects on these parameters were inconclusive. The microstructure of this system has also been analyzed with X-ray Diffraction and light microscopy. These results showed a higher amount of divitrification occurs under both reduced gravity and high gravity conditions. The gravitational effects on formation of pores, overall porosity and apparent porosity for this family of glass-ceramics also shows to be inconclusive. Possible reasons for these results are discussed.

Manerbino, A. R.↗
NASA NTRS2001

Crystallographic Texture and Orientation Variants in Al2O3-Y3Al5O12 Directionally Solidified Eutectic Crystals

Eutectic rods of Al2O3 and Y3Al5O12 were grown by a laser-heated float zone method, and their microstructure and crystallographic texture were studied by scanning electron microscopy, electron backscattered diffraction and x-ray diffraction. The composites were found to be highly textured with two twin-related crystallographic orientation relationships between the phases. Electron backscattered diffraction was employed to determine the spatial distribution of the orientational variants within the samples and to define the crystallographic orientation of various microstructural features.

Frazer, Colleen S.↗
NASA NTRS2017

Thermochemistry of CaO-MgO-Al2O3-SiO2 (CMAS) and Advanced Thermal and Environmental Barrier Coating Systems

CaO-MgO-Al2O3-SiO2 (CMAS) oxides are constituents in a broad number of materials and minerals which have recently inferred to discussions in materials science, planetary science, geochemistry and cosmochemistry communities. In materials science, there is increasing interest in the degradation studies of thermal (TBC) and environmental (EBC) barrier coatings of gas turbines by molten CMAS. CMAS minerals usually are carried by the intake air into gas turbines, e.g. in aircraft engines, and their deposits react at high temperatures (1000C) with the coating materials. This causes degradation and accelerated failure of the static and rotating components of the turbine engines. We discuss some preliminary results of the reactions between CMAS and Rare-Earth (RE Y, Yb, Dy, Gd, Nd and Sm) oxide stabilized ZrO2 or HfO2 systems, and the stability of the resulting oxides and silicates. Plasma sprayed hollow tube samples ( 2.2 mm and 26 mm height) were half filled with CMAS powder, wrapped and sealed with platinum foil, and heat treated at 1310 C for 5h. Samples were characterized by differential scanning calorimetry, X-ray diffraction and cross section electron microscopy analysis.

degradation↗
NASA NTRS2017

High Temperature Degradation of Advanced Thermal and Environmental Barrier Coatings (TEBCs) by CaO-MgO-Al2O3-SiO2 (CMAS)

There is increasing interest in the degradation studies of thermal and environmental barrier coatings (TEBCs) of gas turbines by molten CaO-MgO-Al2O3-SiO2 (CMAS). CMAS minerals are usually referred as silica-containing sand dust and volcano ash materials that are carried by the intake air into gas turbines, e.g. aircraft engines. The low-melting deposits react at high temperatures (1000C) with the coating materials. This causes degradation and accelerated coating failure of the static and rotating components of the turbine engines. We discuss some preliminary results of the reactions between CMAS and Rare-Earth (RE Y, Yb, Dy, Gd, Nd and Sm) oxide stabilized ZrO2 or HfO2 systems, and the stability of the resulting oxides and silicates. Plasma sprayed hollow tube samples (outer diameter 4.7 mm, wall thickness 0.76 mm and 26 mm height) were half filled with CMAS powder, wrapped and sealed with platinum foil, and heat- treated at 1310 C for 5h. Samples were characterized by differential scanning calorimetry, X-ray diffraction and cross section electron microscopy analysis.

Thermal and environmental barrier coatings↗
NASA NTRS2021

Melting and Crystallization Behavior of CaO-MgO-Al2O3-SiO2 Silicates Relevant to Turbine Engine Applications

The melting and crystallization behavior of four quaternary CaO-MgO-Al2O3-SiO2(CMAS) silicates were investigated. The CaO:SiO2 ratios of these systems were based on various terrestrial sources of ingested particles relevant to gas turbine engine operating environments. Melting behavior was characterized using differential scanning calorimetry, and high temperature intrinsic crystallization products were determined by furnace heat treatments of the glasses at 1200°C, 1300°C, and 1400°C. The silicates exhibited a wide range of melting temperatures from ~1240°C up to ~1500°C, with most of the compositions exhibiting incongruent melting behavior. High temperature crystallization products included CaSiO3,CaAl2Si2O8, Ca2MgSi2O7, and Ca(Mg,Al)Si2O6, although SiO2 was the only crystalline phase observed at 1400°C.

Jamesa L. Stokes↗
NASA NTRSDate not supplied

Tribological performance of Al2O3-B2O3 composites: Role of CuOand CaO constituents

Al2O3-B2O3 based composites for wear resistant applications (e.g., seal rings and bearings) were manufactured using powder metallurgy route. Four different compositions were considered to control amount of in situ phases, mainly aluminum borate, formed during sintering. The fabricated composites were characterized using X-ray diffraction to identify the phases. Hardness was measured in terms of micro-hardness. The tribological performance of the composites were evaluated by conducting dry sliding tests against alumina balls at different humidity levels (10 – 95% relative humidity). The X-ray spectrum revealed that increase in B2O3 content in the composites increased the amount of aluminum borate phase that enhanced the micro-hardness. Results revealed that aluminum borate enhanced the wear resistance of the composites, whereas the humidity-sensitive alumina phase reduced friction at higher humidity levels. Furthermore, CuO and CaO (2-5 wt.%) were added separately to the composite, resulting in increased density by 22-48 %. Athough the addition of CuO and CaO led to increase in hardness and wear resistance of the composites, the coefficient of friction was negatively affected. The friction and wear performance along with wear mechanism are discussed with respect to observed phases in the composites.

Ashish K. Kasar↗
DOE OSTI2024

Microstructure and Chemical Composition of Al2O3-, Cr2O3- and MgO-rich Refractories Exposed to Plastic Ashes

Plastics are widely integrated with today’s lifestyle due to their low cost, durability, lightweight, water resistance, and flexibility. However, tremendous plastic waste cause severe threats to the environment. Thus, sustainable recycling of plastic waste is critical, where plastic waste gasification technology with carbon management becomes one of the most effective recycling methods. We simulate the gasification process by exposing the Al2O3-, Cr2O3- and MgO-rich refractories to synthetic plastic ashes at 1500 ℃ for 50 h. A comprehensive study on the microstructure and chemical composition change before/after exposure is conducted using scanning electron microscopy. Meanwhile, the differences among these three refractories after exposure are revealed for quantifying the performance in plastic ashes. Discussion of the results will establish an understanding of the influence of plastic ashes on the microstructure, composition, and phase of different types of refractories, providing insights into designing new refractory materials for future recycling of plastic waste.

Fang, Xiaotian↗