Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Adjoint Models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Numerical Predictions of Sonic Boom Signatures for a Straight Line Segmented Leading Edge Model

A sonic boom wind tunnel test was conducted on a straight-line segmented leading edge (SLSLE) model in the NASA Langley 4- by 4- Foot Unitary Plan Wind Tunnel (UPWT). The purpose of the test was to determine whether accurate sonic boom measurements could be obtained while continuously moving the SLSLE model past a conical pressure probe. Sonic boom signatures were also obtained using the conventional move-pause data acquisition method for comparison. The continuous data acquisition approach allows for accurate signatures approximately 15 times faster than a move-pause technique. These successful results provide an incentive for future testing with greatly increased efficiency using the continuous model translation technique with the single probe to measure sonic boom signatures. Two widely used NASA codes, USM3D (Navier-Stokes) and CART3D-AERO (Euler, adjoint-based adaptive mesh), were used to compute off-body sonic boom pressure signatures of the SLSLE model at several different altitudes below the model at Mach 2.0. The computed pressure signatures compared well with wind tunnel data. The effect of the different altitude for signature extraction was evaluated by extrapolating the near field signatures to the ground and comparing pressure signatures and sonic boom loudness levels.

Elmiligui, Alaa A.↗
NASA NTRS2018

Formulation and Implementation of Inflow/Outflow Boundary Conditions to Simulate Propulsive Effects

Boundary conditions appropriate for simulating flow entering or exiting the computational domain to mimic propulsion effects have been implemented in an adaptive Cartesian simulation package. A robust iterative algorithm to control mass flow rate through an outflow boundary surface is presented, along with a formulation to explicitly specify mass flow rate through an inflow boundary surface. The boundary conditions have been applied within a mesh adaptation framework based on the method of adjoint-weighted residuals. This allows for proper adaptive mesh refinement when modeling propulsion systems. The new boundary conditions are demonstrated on several notional propulsion systems operating in flow regimes ranging from low subsonic to hypersonic. The examples show that the prescribed boundary state is more properly imposed as the mesh is refined. The mass-flowrate steering algorithm is shown to be an efficient approach in each example. To demonstrate the boundary conditions on a realistic complex aircraft geometry, two of the new boundary conditions are also applied to a modern low-boom supersonic demonstrator design with multiple flow inlets and outlets.

Boundary↗
NASA NTRSDate not supplied

TPSAS-NF1676L-14454-DND

FUN3D Core Capabilities - Established as a research code in late 1980’s; now supports numerous internal and external efforts across the speed range - Solves 2D/3D steady and unsteady Euler and RANS equations on node-based mixed element grids for compressible and incompressible flows - General dynamic mesh capability: any combination of rigid / overset / morphing grids, including 6-DOF effects - Aeroelastic modeling using mode shapes, full FEM, CC, etc. - Constrained / multipoint adjoint-based design and mesh adaptation - Distributed development team using agile/extreme software practices including 24/7 regression and performance testing - Capabilities fully integrated, online documentation, training videos, tutorials

Eric J Nielsen↗
NASA NTRS2014

Modeling Sound Propagation Through Non-Axisymmetric Jets

A method for computing the far-field adjoint Green's function of the generalized acoustic analogy equations under a locally parallel mean flow approximation is presented. The method is based on expanding the mean-flow-dependent coefficients in the governing equation and the scalar Green's function in truncated Fourier series in the azimuthal direction and a finite difference approximation in the radial direction in circular cylindrical coordinates. The combined spectral/finite difference method yields a highly banded system of algebraic equations that can be efficiently solved using a standard sparse system solver. The method is applied to test cases, with mean flow specified by analytical functions, corresponding to two noise reduction concepts of current interest: the offset jet and the fluid shield. Sample results for the Green's function are given for these two test cases and recommendations made as to the use of the method as part of a RANS-based jet noise prediction code.

Leib, Stewart J.↗
NASA NTRS2019

Adjoint-Based Mesh Adaptation and Shape Optimization for Simulations with Propulsion

We demonstrate a well-posed formulation of permeable boundary conditions and mass- flow-rate functionals for adjoint-based mesh refinement and shape optimization governed by the steady Euler equations. The boundary conditions are used to model propulsion- system effects of inlets and nozzles. A two-shock diffuser with an analytic solution is used to verify the implementation. Numerical examples show that the adjoint solution is smooth at the boundary, indicating that the discretization is adjoint consistent when exit pressure is specified at subsonic outflow, and stagnation temperature and pressure at subsonic inflow. The results focus on improving simulation techniques for low-boom aircraft analysis and design. By including mass-flow-rate outputs, we obtain reliable estimates of engine flow rates concurrently with nearfield pressure signatures without increasing simulation cost. We also demonstrate the importance of mass-flow-rate constraints in shape optimization by examining trade-offs between maximizing performance of a shrouded supersonic nozzle and minimizing shocks in its nearfield.

Nemec, Marian↗
NASA NTRS2006

Reentry-Vehicle Shape Optimization Using a Cartesian Adjoint Method and CAD Geometry

A DJOINT solutions of the governing flow equations are becoming increasingly important for the development of efficient analysis and optimization algorithms. A well-known use of the adjoint method is gradient-based shape. Given an objective function that defines some measure of performance, such as the lift and drag functionals, its gradient is computed at a cost that is essentially independent of the number of design variables (e.g., geometric parameters that control the shape). Classic aerodynamic applications of gradient-based optimization include the design of cruise configurations for transonic and supersonic flow, as well as the design of high-lift systems. are perhaps the most promising approach for addressing the issues of flow solution automation for aerodynamic design problems. In these methods, the discretization of the wetted surface is decoupled from that of the volume mesh. This not only enables fast and robust mesh generation for geometry of arbitrary complexity, but also facilitates access to geometry modeling and manipulation using parametric computer-aided design (CAD). In previous work on Cartesian adjoint solvers, Melvin et al. developed an adjoint formulation for the TRANAIR code, which is based on the full-potential equation with viscous corrections. More recently, Dadone and Grossman presented an adjoint formulation for the two-dimensional Euler equations using a ghost-cell method to enforce the wall boundary conditions. In Refs. 18 and 19, we presented an accurate and efficient algorithm for the solution of the adjoint Euler equations discretized on Cartesian meshes with embedded, cut-cell boundaries. Novel aspects of the algorithm were the computation of surface shape sensitivities for triangulations based on parametric-CAD models and the linearization of the coupling between the surface triangulation and the cut-cells. The accuracy of the gradient computation was verified using several three-dimensional test cases, which included design variables such as the free stream parameters and the planform shape of an isolated wing. The objective of the present work is to extend our adjoint formulation to problems involving general shape changes. Factors under consideration include the computation of mesh sensitivities that provide a reliable approximation of the objective function gradient, as well as the computation of surface shape sensitivities based on a direct-CAD interface. We present detailed gradient verification studies and then focus on a shape optimization problem for an Apollo-like reentry vehicle. The goal of the optimization is to enhance the lift-to-drag ratio of the capsule by modifying the shape of its heat-shield in conjunction with a center-of-gravity (c.g.) offset. This multipoint and multi-objective optimization problem is used to demonstrate the overall effectiveness of the Cartesian adjoint method for addressing the issues of complex aerodynamic design.

Nemec, Marian↗
DOE OSTI2025

Hidden amplitude zeros from the double-copy map

Recently, Arkani-Hamed proposed the existence of zeros in scattering amplitudes in certain quantum field theories including the cubic adjoint scalar theory Tr ( ϕ 3 ) , the S U ( N ) nonlinear sigma model and Yang-Mills theory. These hidden zeros are special kinematic points where the amplitude vanishes and factorizes into a product of lower-point amplitudes, similar to factorization near poles. In this paper, we show a close connection between the existence of such zeros and the double-copy map. In fact, compatibility with the Bern-Carrasco-Johansson relations requires the presence of these zeros. We also show that these zeros extend via the Kawai-Lewellen-Tye relations to special Galileon amplitudes and their corrections, evincing that these hidden zeros are also present in permutation-invariant amplitudes. Published by the American Physical Society 2025

Bartsch, Christoph (ORCID:0000000174296682)↗
NASA NTRS1997

Aerodynamic Design on Unstructured Grids for Turbulent Flows

An aerodynamic design algorithm for turbulent flows using unstructured grids is described. The current approach uses adjoint (costate) variables for obtaining derivatives of the cost function. The solution of the adjoint equations is obtained using an implicit formulation in which the turbulence model is fully coupled with the flow equations when solving for the costate variables. The accuracy of the derivatives is demonstrated by comparison with finite-difference gradients and a few example computations are shown. In addition, a user interface is described which significantly reduces the time required for setting up the design problems. Recommendations on directions of further research into the Navier Stokes design process are made.

Anderson, W. Kyle↗
NASA NTRS1997

Efficient Approximation for Structural Optimization Under Multiple Constraints

The cooperative agreement covered work between August 1995 and August 1997. The focus of the work was efficient approximations of structural response and sensitivity. The effort proceeded in three directions as follows: (1) Development of an approximation extended to efficient sensitivity approximations and demonstrated for structural models for the High Speed Civil Transport; (2) Preliminary development of the adjoint method for calculating sensitivity derivatives; and (3) A review of method for fast exact reanalysis. Attachments of papers which were submitted during this period are included.

Haftka, Raphael T.↗
NASA NTRS2004

On the Cause of Eastern Equatorial Pacific Ocean T-S Variations Associated with El Nino

The nature of observed variations in temperature-salinity (T-S) relationship between El Nino and non-El Nino years in the pycnocline of the eastern equatorial Pacific Ocean (NINO3 region, 5(deg)S-5(deg)N, 150(deg)W-90(deg)W) is investigated using an ocean general circulation model. The origin of the subject water mass is identified using the adjoint of a simulated passive tracer. The higher salinity during El Nino is attributed to larger convergence of saltier water from the Southern Hemisphere and smaller convergence of fresher water from the Northern Hemisphere.

interannual variability↗
NASA NTRS1996

Optimum Transonic Airfoils Based on the Euler Equations

We solve the problem of determining airfoils that approximate, in a least square sense, given surface pressure distributions in transonic flight regimes. The flow is modeled by means of the Euler equations and the solution procedure is an adjoint- based minimization algorithm that makes use of the inverse Theodorsen transform in order to parameterize the airfoil. Fast convergence to the optimal solution is obtained by means of the pseudo-time method. Results are obtained using three different pressure distributions for several free stream conditions. The airfoils obtained have given a trailing edge angle.

Iollo, Angelo↗
NASA NTRS2016

Challenges and Progress in Aerodynamic Design of Hybrid Wingbody Aircraft with Embedded Engines

We summarize the contributions to high-fidelity capabilities for analysis and design of hybrid wingbody (HWB) configurations considered by NASA. Specifically, we focus on the embedded propulsion concepts of the N2-B and N3-X configurations, some of the future concepts seriously investigated by the NASA Fixed Wing Project. The objective is to develop the capability to compute the integrated propulsion and airframe system realistically in geometry and accurately in flow physics. In particular, the propulsion system (including the entire engine core-compressor, combustor, and turbine stages) is vastly more difficult and costly to simulate with the same level of fidelity as the external aerodynamics. Hence, we develop an accurate modeling approach that retains important physical parameters relevant to aerodynamic and propulsion analyses for evaluating the HWB concepts. Having the analytical capabilities at our disposal, concerns and issues that were considered to be critical for the HWB concepts can now be assessed reliably and systematically; assumptions invoked by previous studies were found to have serious consequences in our study. During this task, we establish firmly that aerodynamic analysis of a HWB concept without including installation of the propulsion system is far from realistic and can be misleading. Challenges in delivering the often-cited advantages that belong to the HWB are the focus of our study and are emphasized in this report. We have attempted to address these challenges and have had successes, which are summarized here. Some can have broad implications, such as the concept of flow conditioning for reducing flow distortion and the modeling of fan stages. The design optimization capability developed for improving the aerodynamic characteristics of the baseline HWB configurations is general and can be employed for other applications. Further improvement of the N3-X configuration can be expected by expanding the design space. Finally, the support of the System Analysis and Integration Element under the NASA Fixed Wing Project has enabled the development and helped deployment of the capabilities shown in this report.

design optimization↗
NASA NTRS2019

High-Fidelity Multidisciplinary Sensitivity Analysis Framework for Multipoint Rotorcraft Optimization

A multidisciplinary, gradient-based sensitivity-analysis methodology is evaluated for optimization of rotorcraft configurations. The tightly coupled discipline models include physics-based fluid dynamics and rotorcraft comprehensive analysis. A discretely-consistent adjoint method accounts for sensitivities of the unsteady flow and unstructured, dynamic, over set grids, while sensitivities of structural responses to aerodynamic loads are computed using a complex-variable method. The methodology is applied to optimize the shape of UH-60A Blackhawk helicopter blades for hover and forward flight conditions. The objective of the multipoint design is to simultaneously increase the rotorcraft figure of merit in a hover flight and reduce the rotor power in a forward flight. Trimmed loose-coupling solutions for the baseline configuration are used to initiate the tight-coupling multidisciplinary analysis. Target thrust and rolling and pitching moments are enforced as optimization constraints. The optimized configuration improves the optimization metrics at both design points. The improved performance and all constraints are maintained over many revolutions beyond the optimization interval, satisfying the required flight conditions. Computational cost of the optimization cycle is assessed in a high-performance computing environment and found affordable for design of rotorcraft in general level-flight conditions.

Wang, Li↗
NASA NTRSDate not supplied

Real-Time Drag Optimization of Aspect Ratio 13.5 Common Research Model with Distributed Flap System

This paper presents a real-time drag optimization study of the aspect ratio 13.5 Common Research Model (CRM) with a distributed mini-plain flap system. A surrogate aerodynamic model of the aspect ratio 13.5 CRM is developed based on an aerodynamic database computed by a transonic panel method to capture the aerodynamic coefficients as functions of the angle of attack, flap deflections, and Mach number. A recursive least-squares parameter estimation algorithm is designed to estimate the aerodynamic parameters of the surrogate model. The estimated surrogate model is then used in an on-line drag optimization strategy based on an adjoint method. The results of the real-time drag optimization indicate a drag reduction of 2.46% for Mach 0.80, 3.37% for Mach 0.85, and 1.95% for Mach 0.88. The results show the convergence of all parameter estimates.

Drag Optimization↗
NASA NTRS2006

Adjoint Sensitivity Computations for an Embedded-Boundary Cartesian Mesh Method and CAD Geometry

Cartesian-mesh methods are perhaps the most promising approach for addressing the issues of flow solution automation for aerodynamic design problems. In these methods, the discretization of the wetted surface is decoupled from that of the volume mesh. This not only enables fast and robust mesh generation for geometry of arbitrary complexity, but also facilitates access to geometry modeling and manipulation using parametric Computer-Aided Design (CAD) tools. Our goal is to combine the automation capabilities of Cartesian methods with an eficient computation of design sensitivities. We address this issue using the adjoint method, where the computational cost of the design sensitivities, or objective function gradients, is esseutially indepeudent of the number of design variables. In previous work, we presented an accurate and efficient algorithm for the solution of the adjoint Euler equations discretized on Cartesian meshes with embedded, cut-cell boundaries. Novel aspects of the algorithm included the computation of surface shape sensitivities for triangulations based on parametric-CAD models and the linearization of the coupling between the surface triangulation and the cut-cells. The objective of the present work is to extend our adjoint formulation to problems involving general shape changes. Central to this development is the computation of volume-mesh sensitivities to obtain a reliable approximation of the objective finction gradient. Motivated by the success of mesh-perturbation schemes commonly used in body-fitted unstructured formulations, we propose an approach based on a local linearization of a mesh-perturbation scheme similar to the spring analogy. This approach circumvents most of the difficulties that arise due to non-smooth changes in the cut-cell layer as the boundary shape evolves and provides a consistent approximation tot he exact gradient of the discretized abjective function. A detailed gradient accurace study is presented to verify our approach. Thereafter, we focus on a shape optimization problem for an Apollo-like reentry capsule. The optimization seeks to enhance the lift-to-drag ratio of the capsule by modifyjing the shape of its heat-shield in conjunction with a center-of-gravity (c.g.) offset. This multipoint and multi-objective optimization problem is used to demonstrate the overall effectiveness of the Cartesian adjoint method for addressing the issues of complex aerodynamic design. This abstract presents only a brief outline of the numerical method and results; full details will be given in the final paper.

Nemec, Marian↗