Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ANGLE OF ATTACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Wing-alone aerodynamic characteristics at high angles of attack

An experimental investigation has been conducted to determine wing-alone supersonic aerodynamic characteristics at high angles of attack. The family of wings tested varied in aspect ratio from 0.5 to 4.0 and taper ratio from 0.0 to 1.0. The wings were tested at angles of attack ranging from 0 to 60 deg and Mach numbers from 1.6 to 4.6. The aerodynamic characteristics were obtained by integrating local pressures measured over the wing surface. Comparison of these data with the limited available data from the literature indicate the present data are free of sting interference effects through the test range of angle of attack. Presented and discussed are results showing the effects of model geometry, Mach number and angle of attack on aerodynamic characteristics consisting of normal force, pitching moment, bending moment, longitudinal center-of-pressure locations, and lateral center-of-pressure locations.

Stallings, R. L., Jr.↗

Measurement of Aerodynamic Forces for Various Mean Angles of Attack on an Airfoil Oscillating in Pitch and on Two Finite-span Wings Oscillating in Bending with Emphasis on Damping in the Stall

The oscillating air forces on a two-dimensional wing oscillating in pitch about the midchord have been measured at various mean angles of attack and at Mach numbers of 0.35 and 0.7. The magnitudes of normal-force and pitching-moment coefficients were much higher at high angles of attack than at low angles of attack for some conditions. Large regions of negative damping in pitch were found, and it was shown that the effect of increasing the Mach number 0.35 to 0.7 was to decrease the initial angle of attack at which negative damping occurred. Measurements of the aerodynamic damping of a 10-percent-thick and of a 3-percent-thick finite-span wing oscillating in the first bending mode indicate no regions of negative damping for this type of motion over the range of variables covered. The damping measured at high angles of attack was generally larger than that at low angles of attack. (author)

Rainey, A Gerald↗

Full-scale high angle-of-attack tests of an F/A-18

This paper presents an overview of high angle-of-attack tests of a full-scale F/A-18 in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center at Moffett Field, California. A production aircraft was tested over an angle-of-attack range of 18 to 50 deg and at wind speeds of up to 100 knots. These tests had three primary test objectives. Pneumatic and mechanical forebody flow control devices were tested at full-scale and shown to produce significant yawing moments for lateral control of the aircraft at high angles of attack. Mass flow requirements for the pneumatic system were found to scale with freestream density and speed rather than freestream dynamic pressure. Detailed measurements of the pressures buffeting the vertical tail were made and spatial variations in the buffeting frequency were found. The LEX fence was found to have a significant effect on the frequency distribution on the outboard surface of the vertical fin. In addition to the above measurements, an extensive set of data was acquired for the validation of computational fluid dynamics codes and for comparison with flight test and small-scale wind tunnel test results.

Meyn, Larry A.↗

Subsonic longitudinal and lateral-directional characteristics of a forward-swept-wing fighter configuration at angles of attack up to 47 deg

Subsonic lateral-direction and longitudinal characteristics of a forward-swept-wing fighter configuration were examined in wind-tunnel tests at Mach numbers of 0.2 and 0.5 for angles of attack from -7 to 47 deg. and over a sidelslip range of +/- 15 deg. The effects of a canard, strakes, vertical tail, and leading- and trailing-edge flaps are examined. The canard and strakes both reduce asymmetric moments and side forces at zero sideslip for angles of attack up to about 30 deg. The canard has a small influence on lateral-directional stability; however, strakes produce a substantial reduction in lateral stability for angles of attack greater than about 20 deg. The vertical tail improves directional stability for angles of attack up to 30 deg. Deflection of the leading-edge flap to 20 deg. at high angles of attack on the strake and canard configurations degrades lateral and directional stability. Deflection of the trailing-edge flap to 20 deg. on the canard configuration generally increases lateral and directional stability at high angles of attack. Leading- and trailing-edge flaps on the wing-body and canard configurations are effective for increased lift only for angles of attack up to about 40 deg. The leading-edge flap remains effective on the strake configuration over the entire angle-of-attack range tested.

Mann, Michael J.↗

Navier-Stokes computations for aerodynamic configurations at high angles of attack

Navier-Stokes computations at high angles of attack over aerodynamic configurations are presented using an implicit finite-volume algorithm. The spatial differencing is upwind-biased for the convective and pressure terms and central for the shear stress and heat transfer terms. The equations are relaxed to steady state with a spatially factored implicit algorithm. In order to treat general geometries, a multiblock patched-grid framework is implemented. Applications and detailed comparisons with experimental data are made for two simple but representative geometric shapes: (1) a highly swept delta wing and (2) a prolate spheroid of 6:1 length-to-diameter. Recent extensions of the algorithm to compute the flow over an F-18 forebody-strake configuration are shown, including comparisons with wind tunnel and flight test results. Comparisons across the range of Reynolds number for all cases indicate that either low Reynolds number or high Reynolds number flows are simulated well, but that flows at intermediate Reynolds number cannot be simulated accurately without a detailed knowledge of the transitional zone between laminar and turbulent flow.

Thomas, J. L.↗

Space Shuttle heating analysis with variation in angle of attack and surface condition

The effects of variations in the angle of attack and surface catalycity condition on the Space Shuttle surface heating along the windward centerline are evaluated. Further, the time history of the nonequilibrium-to-equilibrium surface heating ratio and the boundary edge quantities are analyzed. Results show that a + or - 5% change in the angle of attack does not appreciably influence either the nonequilibrium heating or the nonequilibrium-to-equilibrium heat transfer ratio at higher (75 km) or lower (48 km) altitudes. The variation in the recombination rate parameter is found to affect the surface heating most at an altitude of about 75 km for the STS-2 flight. A maximum reduction of 49% in heating due to nonequilibrium chemistry is obtained at about a 75 km altitude in the nose region of the Orbiter for the STS-2 flight data. In addition, the nonequilibrium effects at the boundary layer edge are found to become less significant for altitudes less than 65 km even though the boundary layer flow may still be in nonquilibrium.

Gupta, R. N.↗

Low-Subsonic Static Stability and Damping Derivatives at Angles of Attack From 0 deg to 90 deg for a Model with a Low-Aspect-Ratio Unswept Wing and Two Different Fuselage Forebodies

An investigation has been made in the Langley free-flight tunnel at low-subsonic speed to determine the static stability, control effectiveness, and damping in roll and yaw of a model with a low-aspect-ratio unswept wing and two different fuselage forebodies at angles of attack from 0 deg to 90 deg. Results were obtained with a fuselage configuration having a long pointed nose and a shorter rounded nose. Although the wing stalled at an angle of attack of about 12 deg, maximum lift did not occur until an angle of attack of about 40 deg or 50 deg was obtained. The static longitudinal stability of the model having a short rounded nose was greater than that of the model having a longer pointed nose over the entire angle-of-attack range. The pointed-nose model had large out-of-trim yawing moments above an angle of attack of about 40 deg. Shortening and rounding the nose of the model delayed these out-of-trim yawing moments to slightly higher angles of attack. Both models were directionally unstable above an angle of attack of about 20 deg, but both had positive effective dihedral over virtually the entire angle-of-attack range. At the higher angles of attack the pointed-nose model had generally better damping in roll than that of the rounded-nose model. Both models had very high damping in yaw at an angle of attack of about 50 deg or 60 deg.

Boisseau, Peter C.↗

Evaluation of High-Angle-of-Attack Handling Qualities for the X-31A Using Standard Evaluation Maneuvers

The X-31A aircraft gross-acquisition and fine-tracking handling qualities have been evaluated using standard evaluation maneuvers developed by Wright Laboratory, Wright Patterson Air Force Base. The emphasis of the testing is in the angle-of-attack range between 30 deg. and 70 deg. Longitudinal gross-acquisition handling qualities results show borderline Level l/Level 2 performance. Lateral gross-acquisition testing results in Level l/Level 2 ratings below 45 deg. angle of attack, degrading into Level 3 as angle of attack increases. The fine tracking performance in both longitudinal and lateral axes also receives Level 1 ratings near 30 deg. angle of attack, with the ratings tending towards Level 3 at angles of attack greater than 50 deg. These ratings do not match the expectations from the extensive close-in combat testing where the X-31A aircraft demonstrated fair to good handling qualities maneuvering for high angles of attack. This paper presents the results of the high-angle-of-attack handling qualities flight testing of the X-31A aircraft. Discussion of the preparation for the maneuvers, the pilot ratings, and selected pilot comments are included. Evaluation of the results is made in conjunction with existing Neal Smith, bandwidth, Smith-Geddes, and military specifications.

Stoliker, Patrick C.↗

Evaluation of High-Angle-of-Attack Handling Qualities for the X-31A Using Standard Evaluation Maneuvers

The X-31A aircraft gross-acquisition and fine-tracking handling qualities have been evaluated using standard evaluation maneuvers developed by Wright Laboratory, Wright-Patterson Air Force Base. The emphasis of the testing is in the angle-of-attack range between 30 deg and 70 deg. Longitudinal gross-acquisition handling qualities results show borderline Level 1/Level 2 performance. Lateral gross-acquisition testing results in Level 1/Level 2 ratings below 45 deg angle of attack, degrading into Level 3 as angle of attack increases. The fine-tracking performance in both longitudinal and lateral axes also receives Level 1 ratings near 30 deg angle of attack, with the ratings tending towards Level 3 at angles of attack greater than 50 deg. These ratings do not match the expectations from the extensive close-in combat testing where the X-31A aircraft demonstrated fair to good handling qualities maneuvering for high angles of attack. This paper presents the results of the high-angle-of-attack handling qualities flight testing of the X-31A aircraft. Discussion of the preparation for the maneuvers, the pilot ratings, and selected pilot comments are included. Evaluation of the results is made in conjunction with existing Neal-Smith, bandwidth, Smith-Geddes, and military specifications.

Stoliker, Patrick C.↗

Side-force alleviation on slender, pointed forebodies at high angles of attack

A new device was proposed for alleviating high angle-of-attack side force on slender, pointed forebodies. A symmetrical pair of separation strips in the form of helical ridges are applied to the forebody to disrupt the primary lee-side vortices and thereby avoid the instability that produces vortex asymmetry. Preliminary wind tunnel tests at Mach 0.3 and Reynolds no. 5,250,000 on a variety of forebody configurations and on a wing-body combination at angles of attack up to 56 degrees, demonstrated the effectiveness of the device.

Rao, D. M.↗

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, Ramani↗

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, R.↗

High angle-of-attack aerodynamics of a strake-canard-wing V/STOL fighter configuration

High angle-of-attack aerodynamic data are analyzed for a strake-canard-wing V/STOL fighter configuration. The configuration represents a twin-engine supersonic V/STOL fighter aircraft which uses four longitudinal thrust-augmenting ejectors to provide vertical lift. The data were obtained in tests of a 9.39 percent scale model of the configuration in the NASA Ames 12-Foot Pressure Wind Tunnel, at a Mach number of 0.2. Trimmed aerodynamic characteristics, longitudinal control power, longitudinal and lateral/directional stability, and effects of alternate strake and canard configurations are analyzed. The configuration could not be trimmed (power-off) above 12 deg angle of attack because of the limited pitch control power and the high degree of longitudinal instability (28 percent) at this Mach number. Aerodynamic center location was found to be controllable by varying strake size and canard location without significantly affecting lift and drag. These configuration variations had relatively little effect on the lateral/directional stability up to 10 deg angle of attack.

Durston, D. A.↗

Wind-tunnel investigation to determine the low speed yawing stability derivatives of a twin jet fighter model at high angles of attack

An investigation was conducted to determine the low-speed yawing stability derivatives of a twin-jet fighter airplane model at high angles of attack. Tests were performed in a low-speed tunnel utilizing variable-curvature walls to simulate pure yawing motion. The results of the study showed that at angles of attack below the stall the yawing derivatives were essentially independent of the yawing velocity and sideslip angle. However, at angles of attack above the stall some nonlinear variations were present and the derivatives were strongly dependent upon sideslip angle. The results also showed that the rolling moment due to yawing was primarily due to the wing-fuselage combination, and that at angles of attack below the stall both the vertical and horizontal tails produced significant contributions to the damping in yaw. Additionally, the tests showed that the use of the forced-oscillation data to represent the yawing stability derivatives is questionable, at high angles of attack, due to large effects arising from the acceleration in sideslip derivatives.

Coe, P. L., Jr.↗

Laminar separation on a blunted cone at high angles of attack

A new technique is reported for calculating the entire flow field on spherically blunted cones at high angles of attack and high laminar Reynolds numbers. An approximate system of parabolic equations obtained from the steady Navier-Stokes equations by assuming the viscous, streamwise derivative terms are small compared to the viscous normal and circumferential derivatives is the basis of the calculations. These equations are valid for both the inviscid and viscous regions, including the circumferential separation zone that develops on the leeward side at high angles of attack. Two different methods are used to obtain the initial conditions for these equations at the sphere cone tangency plane. For small nose Reynolds numbers, an axisymmetric merged layer solution around a sphere is rotated to provide a three-dimensional initial plane of data. For large nose Reynolds numbers, the nose region is solved using an inviscid, three dimensional time dependent solution combined with a boundary layer solution for the viscous flow. The computed flowfield including the leeward separation region is described and compared with data for a 7 deg half angle cone at 10 deg angle of attack, and a blunt 15 deg half angle cone at 15 deg angle of attack.

Lubard, S. C.↗

Flight characteristics of a modified Schweizer SGS1-36 sailplane at low and very high angles of attack

A manned flight research program using a modified sailplane was conducted to very high angles of attack at the NASA-Ames. Piloting techniques were established that enabled the pilot to attain and stabilize on an angle of attack in the 30 to 72 deg range. Aerodynamic derivatives were estimated from the flight data for both low and very high angles of attack and are compared to wind tunnel data. In addition, limited performance and trim data are presented.

Sim, Alex G.↗