Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AFTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Two-dimensional computer code for design assessment of SRM aft closure environment

A general interpolants method for constructing numerical analogs of the partial differential equations of continuum mechanics and which combines the best features of both finite element and finite difference methods was used in a two dimensional axisymmetric analysis of the space shuttle solid motor aft closure region flowfield. The numerical technique used is discussed as well as the results of the analysis. A steady state solution for the submerged nozzle nose region indicates the development of an area gas flow recirculation near the propellant burning surface boundary and in the region of the underside of the nozzle nose. This recirculation region remains spatially fixed for successive iterations (greater than 800) of the solution.

Freeman, J. A.↗
NASA NTRS1978

Flight-measured pressure characteristics of aft-facing steps in high Reynolds number flow at Mach numbers of 2.20, 2.50, and 2.80 and comparison with other data

The YF-12 airplane was studied to determine the pressure characteristics associated with an aft-facing step in high Reynolds number flow for nominal Mach numbers of 2.20, 2.50, and 2.80. Base pressure coefficients were obtained for three step heights. The surface static pressures ahead of and behind the step were measured for the no-step condition and for each of the step heights. A boundary layer rake was used to determine the local boundary layer conditions. The Reynolds number based on the length of flow ahead of the step was approximately 10 to the 8th power and the ratios of momentum thickness to step height ranged from 0.2 to 1.0. Base pressure coefficients were compared with other available data at similar Mach numbers and at ratios of momentum thickness to step height near 1.0. In addition, the data were compared with base pressure coefficients calculated by a semiempirical prediction method. The base pressure ratios are shown to be a function of Reynolds number based on momentum thickness. Profiles of the surface pressures ahead of and behind the step and the local boundary layer conditions are also presented.

Powers, S. G.↗
NASA NTRS1978

Flight-measured pressure characteristics of aft-facing steps in thick boundary layer flow for transonic and supersonic Mach numbers

Aft-facing step base pressure flight data were obtained for three step heights for nominal transonic Mach numbers of 0.80, 0.90, and 0.95, and for supersonic Mach numbers of 2.2, 2.5, and 2.8 with a Reynolds number, based on the fuselage length ahead of the step, of about 10 to the 8th power. Surface static pressures were measured ahead of the step, behind the step, and on the step face (base), and a boundary layer rake was used to obtain boundary layer reference conditions. A comparison of the data from the present and previous experiments shows the same trend of increasing base pressure ratio (decreasing drag) with increasing values of momentum thickness to step height ratios. However, the absolute level of these data does not always agree at the supersonic Mach numbers. For momentum thickness to height ratios near 1.0, the differences in the base pressure ratios appear to be primarily a function of Reynolds number based on the momentum thickness. Thus, for Mach numbers above 2, the data analyzed show that the base pressure ratio decreases (drag increases) as Reynolds number based on momentum thickness increases for a given momentum thickness and step height.

Powers, S. G.↗
NASA NTRS1977

Boron/aluminum skins for the DC-10 aft pylon

Three boron/aluminum aft pylon 'boat tail' skins were designed, fabricated, and installed on three DC-10 aircraft for a five-year flight service demonstration test. Inspection and tests of the skins will establish the ability of the composite to withstand long-time flight service exposures to high temperatures, sonic fatigue, and flutter. The results of a preliminary testing program yielded room and elevated temperature data on the tension, compression, in-plane shear, interlaminar shear, bolt bearing, and tension fatigue properties of the oriented eleven-ply boron/aluminum laminates, and this information, together with a stress analysis, was used to obtain Federal Aviation Administration approval. Present state-of-the-art technology was used in the fabrication of the skins, and these were installed on the existing titanium substructure with the same number and size mechanical fasteners as are used for the present titanium skins.

Elliott, S. Y.↗
NASA NTRS1979

Propellant grain dynamics in aft attach ring of shuttle solid rocket booster

An analytical technique for implementing simultaneously the temperature, dynamic strain, real modulus, and frequency properties of solid propellant in an unsymmetrical vibrating ring mode is presented. All dynamic parameters and sources are defined for a free vibrating ring-grain structure with initial displacement and related to a forced vibrating system to determine the change in real modulus. Propellant test data application is discussed. The technique was developed to determine the aft attach ring stiffness of the shuttle booster at lift-off.

Verderaime, V.↗
NASA NTRS1979

Pressure distributions on three different cruciform aft-tail control surfaces of a wingless missile at mach 1.60, 2.36, and 3.70 Volume 1: Trapezoidal tail

The results of pressure distribution tests conducted in the Langley Unitary Plan wind tunnel are presented. The data were obtained for three sets of cruciform aft-tail control surfaces on a wingless missile model at Mach numbers of 1.60, 2.36, and 3.70 for angles of attack from -4 degrees to 20 degrees, model roll angles from 0 degrees to 90 degrees, and tail deflections of 0 degrees and 15 degrees. The test Reynolds number used was 6.6 million per meter.

Lamb, M.↗
NASA NTRS1979

Development of forward and aft separation bolts for the NASA Space Shuttle solid rocket booster separation system

A program is underway to design, develop, fabricate, and qualify large high-load forward and aft separation bolts for the Space Shuttle; the bolts will serve as attachment between two solid rocket boosters and the external tank. This paper reviews bolt development, with emphasis on the scaling of components, the use of high strength maraging steel for the internal components, and the use of lead as a hydraulic fluid.

Nein, H.↗
NASA NTRS1981

Aeropropulsive characteristics of twin nonaxisymmetric vectoring nozzles installed with forward-swept and aft-swept wings

An investigation was conducted in the Langley 16 Foot Transonic Tunnel to determine the aeropropulsive characteristics of a single expansion ramp nozzle (SERN) and a two dimensional convergent divergent nozzle (2-D C-D) installed with both an aft swept and a forward swept wing. The SERN was tested in both an upright and an inverted position. The effects of thrust vectoring at nozzle vector angles from -5 deg to 20 deg were studied. This investigation was conducted at Mach numbers from 0.40 to 1.20 and angles of attack from -2.0 deg to 16 deg. Nozzle pressure ratio was varied from 1.0 (jet off) to about 9.0. Reynolds number based on the wing mean geometric chord varied from about 3 million to 4.8 million, depending upon free stream number.

Capone, F. J.↗
NASA NTRS1979

Pressure distributions on three different cruciform aft-tail control surfaces of a wingless missile at Mach 1.60, 2.36, and 3.70. Volume 1: Trapezoidal tail

The results of pressure distribution tests conducted in a wind tunnel are presented without analysis. The data were obtained for trapezoidal aft tail control surfaces on a wingless missile model at Mach numbers of 1.60, 2.36, and 3.70 for angles of attack from -4 to 20 deg model roll angles from 0 to 90 deg and tail deflections of 0 and -15 deg. The test Reynolds number used was 6.6 million per meter.

Lamb, M.↗
NASA NTRS1975

Aerodynamic characteristics of 10 percent thick NASA supercritical airfoils with different aft camber

The aerodynamic characteristics of several supercritical airfoils interim to the improved 10-percent thick NASA supercritical airfoil 26a are discussed. The airfoils have related slope and curvature distributions over the rear which result in different aft camber. For identification, the airfoils are designated supercritical airfoils 12, 13, 21, 22, and 24. Data is presented without analysis.

Harris, C. D.↗
NASA NTRS1983

Water impact test of aft skirt end ring, and mid ring segments of the Space Shuttle Solid Rocket Booster

The results of water impact loads tests using aft skirt end ring, and mid ring segments of the Space Shuttle Solid Rocket Booster (SRB) are examined. Dynamic structural response data is developed and an evaluation of the model in various configurations is presented. Impact velocities are determined for the SRB with the larger main chute system. Various failure modes are also investigated.

Source record↗
NASA NTRS1984

External Tank Aft Cargo Carrier

It has been found that the majority of the flights of the Space Transportation System (STS) are loaded above 90 percent volume capacity, while approximately 35 percent of the flights carry less than 50 percent of the lift capability (65,000 lb) of the current STS. This situation implies that the payload could be increased if the volume for the additional payload were available on the STS. The employment of the External Tank (ET) Aft Cargo Carrier (ACC) would provide the additional volume needed and, thus, enable the STS to use its residual capability. The current ACC configuration is an evolution of two years of study. The ACC is a general purpose payload carrier which can be adapted to specific large diameter payloads. The improvement of the STS capabilities by the ACC is discussed, and future applications are considered.

Mobley, T. B.↗
NASA NTRS1984

External tank aft cargo carrier

The External Tank (ET) Aft Cargo Carrier (ACC) is a low cost, low risk augmentation of the Space Transportation System (STS). It almost doubles the cargo volume of the STS while minimally impacting other STS elements (orbiter, ET and solid rocket boosters SRBs, launch facilities and STS operations. In addition to increasing the potential volume of cargo carried on a Shuttle launch, the ACC provides the following additional benefits: (1) Increased STS competitiveness for payloads; (2) Increased cargo manifest flexibility; (3) Increased spacecraft design options; (4) Alternate manifesting for special payloads; and (5) Future space platform/station design options.

Mobley, T. B.↗
NASA NTRS1984

Water impact laboratory and flight test results for the space shuttle solid rocket booster aft skirt

A series of water impact tests was conducted using full-scale segment representations of the Space Shuttle Solid Rocket Booster (SRB) aft skirt structure. The baseline reinforced structural design was tested as well as various alternative design concepts. A major portion of the test program consisted of evaluating foam as a load attenuation material. Applied pressures and response strains were measured for impact velocities from 40 feet per second (ft/s) to 110 ft/s. The structural configurations, test articles, test results, and flight results are described.

Kross, D. A.↗
NASA NTRS1980

Results of tests on a specimen of the SRB aft skirt heat shield curtain in the MSFC LRLF

A full scale segment of the actual Solid Rocket Booster aft skirt heat shield curtain was tested in the Large Radiant Lamp Facility (LRLF) at Marshall Space Flight Center. The curtain was mounted in the horizontal position in the same manner as it is to be mounted on the SRB. A shaker rig was designed and used to provide a motion of the curtain, simulating that to be caused in flight by vehicle acoustics. Thermocouples were used to monitor curtain materials temperatures. Both ascent and reentry heat loads were applied to the test specimen. All aspects of the test setup performed as expected, and the test was declared successful.

Dean, W. G.↗
NASA NTRS1982

Results of tests of the SRB aft skirt heat shield curtain in the MSFC Hot Gas Facility

During the first two space shuttle flights the aft skirt heat shield curtain performed well during ascent but failed during reentry. This exposed the inside of the skirt and its subsystems to reentry heating. The resulting exposure damaged various expensive systems items and therefore a curtain reassessment is required. As a part of this reassessment, tests were conducted in the MSFC Hot Gas Facility (HGF). The purposes of these tests were to determine if the curtain would fail in a manner similar to that in flight and to demonstrate that meaningful tests of the curtain can be conducted in the HGF.

Dean, W. G.↗
NASA NTRS1986

Vertical drop test of a transport fuselage section located aft of the wing

A 12-foot long Boeing 707 aft fuselage section with a tapering cross section was drop tested at the NASA Langley Research Center to measure structural, seat, and occupant response to vertical crash laods and to provide data for nonlinear finite element modeling. This was the final test in a series of three different transport fuselage sections tested under identical conditions. The test parameters at impact were: 20 ft/s velocity, and zero pitch, roll, and yaw. In addition, the test was an operational shock test of the data acquisition system used for the Controlled Impact Demonstration (CID) of a remotely piloted Boeing 720 that was crash tested at NASA Ames Dryden Flight Research Facility on December 1, 1984. Post-test measurements of the crush showed that the front of the section (with larger diameter) crushed vertically approximately 14 inches while the rear crushed 18 inches. Analysis of the data traces indicate the maximum peak normal (vertical) accelerations at the bottom of the frames were approximately 109 G at body station 1040 and 64 G at body station 1120. The peak floor acceleration varied from 14 G near the wall to 25 G near the center where high frequency oscillations of the floor were evident. The peak anthropomorphic dummy pelvis normal (vertical) acceleration was 19 G's.

Fasanella, E. L.↗