Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind tunnel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Blade-Mounted Flap Control for BVI Noise Reduction Proof-of-Concept Test

This report describes a wind tunnel test of the McDonnell Douglas Helicopter Systems (MDHS) Active Flap Model Rotor at the NASA Langley 14- by 22-Foot Subsonic Tunnel. The test demonstrated that BVI noise reductions and vibration reductions were possible with the use of an active flap. Aerodynamic results supported the acoustic data trends, showing a reduction in the strength of the tip vortex with the deflection of the flap. Acoustic results showed that the flap deployment, depending on the peak deflection angle and azimuthal shift in its deployment schedule, can produce BVI noise reductions as much as 6 dB on the advancing and retreating sides. The noise reduction was accompanied by an increase in low frequency harmonic noise and high frequency broadband noise. A brief assessment of the effect of the flap on vibration showed that significant reductions were possible. The greatest vibration reductions (as much as 76%) were found in the four per rev pitching moment at the hub. Performance improvement cam results were inconclusive, as the improvements were predicted to be smaller than the resolution of the rotor balance.

Dawson, Seth↗
NASA NTRS1973

Meeting the challenge of advanced helicopters.

Wind tunnel tests that are conducted during the course of a typical aircraft development program are considered. The objectives of a test program are to reduce technical and financial risk and to improve product performance. Typical fixed-wing and rotary-wing aircraft development programs are compared. It is concluded that existing wind tunnel practice is not adequate in relation to the consequences from serious problems remaining undetected until flight test. In fact, the ultimate goal of the wind tunnel test program should leave nothing for the flight test program but the demonstration of the final product.-

Kelly, M. W.↗
NASA NTRS1934

Preliminary Wind-Tunnel and Flight Tests of a Balanced Split Flap, Special Report

One disadvantage that has been apparent in the operation of split flaps as used to date is the time and effort required to operate them. In this communication an investigation is being made of possible means for balancing them aerodynamically to make their operation easier. Several arrangements have been tested in the 7 by 210 foot wind tunnel, and the results of the wind-tunnel tests as well as preliminary flight tests on one of the more promising forms are given in this paper.

Weick, Fred E.↗
NASA NTRSDate not supplied

Parametric Study of the Forward Attachment Geometry for the Space Launch System Next Generation Booster

Launch vehicle transonic buffet environments can generate large dynamic structural loads and vibratory responses. For the Space Launch System (SLS) vehicle, the highest transonic buffet environments have been observed in the multibody region between the core and solid rocket boosters, particularly downstream of the booster forward attachment. The buffet environment is particularly sensitive to the outer mold line (OML) of the forward attachment, and even relatively minor geometry changes can have large impacts on buffet and other aerodynamic environments. The SLS program is redesigning the booster for the Block 2 vehicle to support updated mission goals. This redesign necessitated changes in the forward attachment geometry, which raised concerns about the buffet and vibroacoustic environments. A preliminary study was conducted that developed multiple forward attachment geometries that satisfied the programmatic requirements, but the aerodynamic environment impacts were unclear. In March 2022, a wind-tunnel test was conducted at the NASA Ames 11- by 11-foot Transonic Wind Tunnel to study these environments generated from each of the configurations in order to select the most viable candidate. This paper will discuss this test campaign, the results from the parametric study, as well as general observations regarding OML features that impact the buffet environment. Buffet environments will be presented and compared for each configuration and comparisons presented where applicable.

buffet↗
NASA NTRS1972

Surface pressure and inviscid flow field properties of the McDonnell-Douglas delta-wing orbiter for nominal Mach number of 8, Volume 1

The results of a wind tunnel test program to determine the surface pressures and flow distribution on the McDonnell Douglas Orbiter configuration are presented. Tests were conducted in hypersonic wind tunnel at Mach 8. The freestream unit Reynolds number was 3.7 time one million per foot. Angle of attack was varied from 10 degrees to 60 degrees in 10 degree increments.

Warmbrod, J. D.↗
NASA NTRS1937

Full-scale Wind-tunnel and Flight Tests of a Fairchild 22 Airplane Equipped with External-airfoil Flaps

Wind-tunnel and flight tests have been made of a Fairchild 22 airplane equipped with a wing having external-airfoil flaps that also perform the function of ailerons. Lift, drag, and pitching-moment coefficients of the airplane with several flap settings, and the rolling- and yawing-moment coefficients with the flaps deflected as ailerons were measured in the full-scale tunnel with the horizontal tail surfaces and propeller removed. The effect of the flaps on the low speed and on the take-off and landing characteristics, the effectiveness of flaps when used as ailerons, and the forces required to operate them as ailerons were determined in flight. The wind-tunnel tests showed that the flaps increased the maximum lift coefficient of the airplane from 1.51 with the flap in the minimum drag position to 2.12 with the flap in the minimum drag position to 2.12 with the flap deflected 30 degrees. In the flight tests the minimum speed decreased from 46.8 miles per hour with the flaps up to 41.3 miles per hour with the flaps deflected. The required take-off run to attain a height of 50 feet was reduced from 820 to 750 feet and the landing run from a height of 50 feet was reduced from 930 to 480 feet. The flaps for this installation gave lateral control that was not entirely satisfactory. Their rolling action was good but the adverse yaw resulting from their use was greater than is considerable, and the stick forces required to operate them increased too rapidly with speed.

Reed, Warren D↗
NASA NTRS2018

Cyclic Symmetry Finite Element Forced Response Analysis of a Distortion-Tolerant Fan with Boundary Layer Ingestion

Accurate prediction of the blade vibration stress is required to determine overall durability of fan blade design under Boundary Layer Ingestion (BLI) distorted flow environments. Traditional single blade modeling technique is incapable of representing accurate modeling for the entire rotor blade system subject to complex dynamic loading behaviors and vibrations in distorted flow conditions. A particular objective of our work was to develop a high-fidelity full-rotor aeromechanics analysis capability for a system subjected to a distorted inlet flow by applying cyclic symmetry finite element modeling methodology. This reduction modeling method allows computationally very efficient analysis using a small periodic section of the full rotor blade system. Experimental testing by the use of the 8-foot by 6-foot Supersonic Wind Tunnel Test facility at NASA Glenn Research Center was also carried out for the system designated as the Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan (BLI2DTF) technology development. The results obtained from the present numerical modeling technique were evaluated with those of the wind tunnel experimental test, toward establishing a computationally efficient aeromechanics analysis modeling tool facilitating for analyses of the full rotor blade systems subjected to a distorted inlet flow conditions. Fairly good correlations were achieved hence our computational modeling techniques were fully demonstrated. The analysis result showed that the safety margin requirement set in the BLI2DTF fan blade design provided a sufficient margin with respect to the operating speed range.

forced response analysis↗
NASA NTRS2013

Structural Dynamics Modeling of HIRENASD in Support of the Aeroelastic Prediction Workshop

An Aeroelastic Prediction Workshop (AePW) was held in April 2012 using three aeroelasticity case study wind tunnel tests for assessing the capabilities of various codes in making aeroelasticity predictions. One of these case studies was known as the HIRENASD model that was tested in the European Transonic Wind Tunnel (ETW). This paper summarizes the development of a standardized enhanced analytical HIRENASD structural model for use in the AePW effort. The modifications to the HIRENASD finite element model were validated by comparing modal frequencies, evaluating modal assurance criteria, comparing leading edge, trailing edge and twist of the wing with experiment and by performing steady and unsteady CFD analyses for one of the test conditions on the same grid, and identical processing of results.

Wieseman, Carol↗
NASA NTRS2017

ARC Array Development Test Sweeping Jet Actuator Research

Plans and status of a wind tunnel test programs at ARC, GRC, and LaRC of a small reference acoustic array and references sources are reviewed. The GRC test in the jet nozzle rig is in progress, the ARC test will begin in the Army 7x10 ft. Wind tunnel this May, and the LaRC test will take place in the Quiet Flow Facility later this summer. These efforts will serve to validate the small acoustic array as a reference array sensor for accurate acoustic level measurement with suppression of background noise, and to compare the relative noise levels and recieved signal levels for different array installations

wind tunnel aeroacoustic measurements↗
NASA NTRS1991

Recent rotorcraft aeroelastic testing in the Langley Transonic Dynamics Tunnel

Wind-tunnel testing of a properly scaled aeroelastic model helicopter rotor is considered a necessary phase in the design and development of new rotor systems. For this reason, extensive testing of aeroelastically scaled model rotors is done in the Transonic Dynamics Tunnel (TDT) located at the Langley Research Center. A unique capability of this facility, which enables proper dynamic scaling, is the use of diflourodichloromethane, or Refrigerant-12 (R-12) as a test medium. The paper presents a description of the TDT and a discussion of the benefits of using R-12 as a test medium. A description of the system used to conduct model tests is provided and examples of recent rotor tests are cited to illustrate the types of aeroelastic model rotor tests conducted in the TDT.

Yeager, William T., Jr.↗
NASA NTRSDate not supplied

Parametric Study of the Forward Attachment Geometry for the Space Launch System Next Generation Booster

Launch vehicle transonic buffet environments can generate large dynamic structural loads and vibratory responses. For the Space Launch System (SLS) vehicle, the highest transonic buffet environments have been observed in the multibody region between the core and solid rocket boosters, particularly downstream of the booster forward attachment. The buffet environment is particularly sensitive to the outer mold line (OML) of the forward attachment, and even relatively minor geometry changes can have large impacts on buffet and other aerodynamic environments. The SLS program is redesigning the booster for the Block 2 vehicle to support updated mission goals. This redesign necessitated changes in the forward attachment geometry, which raised concerns about the buffet and vibroacoustic environments. A preliminary study was conducted that developed multiple forward attachment geometries that satisfied the programmatic requirements, but the aerodynamic environment impacts were unclear. In March 2022, a wind-tunnel test was conducted at the NASA Ames 11- by 11-foot Transonic Wind Tunnel to study these environments generated from each of the configurations in order to select the most viable candidate. This paper will discuss this test campaign, the results from the parametric study, as well as general observations regarding OML features that impact the buffet environment. Buffet environments will be presented and compared for each configuration and comparisons presented where applicable.

buffet↗
NASA NTRS2018

Computational and Experimental Study of Plume and Shock Interaction Effects on Sonic Boom in the NASA Ames 9x7 Supersonic Wind Tunnel

A wind tunnel test was performed in the NASA Ames 9x7 Supersonic Wind Tunnel focusing on the shock waves traveling through and interacting with an exhaust nozzle plume. This experimental study was conducted to develop and validate the CFD capability required to accurately include nozzle flow with impinging shock effects on near field and ground‐propagated sonic boom signatures. The model was made to be generic, and included a simple nozzle shape, two different aft decks, and a few generic horizontal tails. High pressure air was pumped through a nozzle at various nozzle pressure ratios (NPR) to represent the engine plume in flight. The three different aft body representations each created a different shock wave signature that passed through the plume. An aft deck configuration, where part of the aircraft shields the nozzle plume, was also tested. Retroreflective Background-Oriented Schlieren (RBOS) was used to obtain schlieren images of the flow field around the model and behind the model. This study compares wind tunnel data and numerical simulations conducted by the NASA Tetrahedral Unstructured Software System CFD code, USM3D.

Winski, Courtney S.↗
NASA NTRS2017

Boundary Condition Study for the Juncture Flow Experiment in the NASA Langley 14x22-Foot Subsonic Wind Tunnel

Because future wind tunnel tests associated with the NASA Juncture Flow project are being designed for the purpose of CFD validation, considerable effort is going into the characterization of the wind tunnel boundary conditions, particularly at inflow. This is important not only because wind tunnel flowfield nonuniformities can play a role in integrated testing uncertainties, but also because the better the boundary conditions are known, the better CFD can accurately represent the experiment. This paper describes recent investigative wind tunnel tests involving two methods to measure and characterize the oncoming flow in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The features of each method, as well as some of their pros and cons, are highlighted. Boundary conditions and modeling tactics currently used by CFD for empty-tunnel simulations are also described, and some results using three different CFD codes are shown. Preliminary CFD parametric studies associated with the Juncture Flow model are summarized, to determine sensitivities of the flow near the wing-body juncture region of the model to a variety of modeling decisions.

Rumsey, C. L.↗
NASA NTRS2010

Quantification of the Uncertainties for the Ares I A106 Ascent Aerodynamic Database

A detailed description of the quantification of uncertainties for the Ares I ascent aero 6-DOF wind tunnel database is presented. The database was constructed from wind tunnel test data and CFD results. The experimental data came from tests conducted in the Boeing Polysonic Wind Tunnel in St. Louis and the Unitary Plan Wind Tunnel at NASA Langley Research Center. The major sources of error for this database were: experimental error (repeatability), database modeling errors, and database interpolation errors.

Houlden, Heather P.↗
NASA NTRS2023

A Guide to Forced Oscillation Data Processing and Analysis

The NASA Langley Research Center Flight Dynamics Branch has a long history of experimental testing of aircraft and spacecraft flight dynamics. One of the frequently used wind tunnel test methods is forced oscillation testing. This method involves a model mounted on a specialized dynamic test rig in a tunnel and oscillated about a body axis, typically at a fixed sinusoidal frequency and amplitude. This report provides the derivation of two commonly used data reduction methods and introduces one new method to extract the linear dynamic derivatives from forced oscillation wind tunnel data.

Flight Dynamics↗
NASA NTRSDate not supplied

Joint Acceptance Attenuation Factor of Integrated Pressure with Unsteady Pressure-Sensitive Paint Measurements

The Unsteady Pressure-Sensitive Paint (uPSP) is widely used to measure the surface pressure of the scaled model in the wind tunnel tests. Compared to the conventional pressure transducers, uPSP has the advantage of high spatial resolution. With multiple high-speed cameras, the uPSP data collected with the camera pixels are mapped to the surface grid of the scaled model and converted to pressure. The shot noise, which is associated with the quantum processes both in the generation of the photons by the luminescent uPSP and in the conversion of the photons into electrons within the camera, is the dominant component of the noise in the uPSP measurement. The integrated pressure is usually computed as an area-weighted average of the uPSP measured pressures on the grid nodes of a user-defined patch. The effect of the shot noise is reduced in the integrated pressure; however, the measurement of the aerodynamic pressure is also attenuated. This paper discusses the Joint Acceptance Attenuation Factor (JAAF) of the integrated pressure with uPSP measurements. The JAAF is defined as the ratio of the auto or cross Power Spectral Density (PSD) of the integrated aerodynamic pressure on the patch to the average auto PSD of the aerodynamic pressure on the grid nodes of the patch. Under the assumption that the cross spectrum of the aerodynamic pressure can be described with the Corcos model, the closed-form formula of the JAAF is derived for the integrated pressure on rectangular patches via the summation of uPSP measurements on discrete grid nodes. The closed-form formula is verified via the integration of the pressure field of Corcos model over continuous areas. The properties of the JAAF with different parameters are presented and the applications in the comparison of the spectrum of the pressure transducers and uPSP measurements, which were collected in the NASA Space Launch System (SLS) tests with the 11-by-11-foot transonic wind tunnel at NASA Ames Research Center in December 2017 and September 2019 respectively, are also discussed. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities(AETC) Portfolio Office.

Unsteady Pressure-Sensitive Paint↗