SEARCH · Engineering Papers

Results for “vector control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Experimental performance of a ventral nozzle with pitch and yaw vectoring capability for SSTOVL aircraft

Aircraft with supersonic, short takeoff and vertical landing capability have been proposed to replace some of the current high-performance aircraft. Several of these configurations use a ventral nozzle in the lower fuselage, aft of the center of gravity, for lift or pitch control. Internal vanes canted at 20 deg were added to a swivel-type ventral nozzle and tested at tailpipe to ambient pressure ratios up to 5.0 on the Powered Lift Facility at NASA Lewis Research Center. The addition of sets of four or seven vanes decreased the discharge coefficient of the nozzle by at least 6 percent and did not effect the thrust coefficient. Side force produced by the nozzle with vanes was 14 percent or more of the vertical force. In addition, this side force caused only a smalll loss in vertical force in comparison to the nozzle without vanes. The net thrust force was 8 deg from the vertical for four vanes and 10.5 deg for seven.

Esker, Barbara S.↗

NASA NTRS1975

Factors affecting handling qualities of a lift-fan aircraft during steep terminal area approaches

The XV-5B lift-fan aircraft was used to explore the factors affecting handling qualities in the terminal area. A 10 deg ILS approach task was selected to explore these problems. Interception of the glide slope at 457.2 m, glide slope tracking, deceleration along the glide slope to a spot hover were considered. Variations in airplane deck angle, deceleration schedule, and powered-lift management were studied. The overall descent performance envelope was identified on the basis of fan stall, maximum comfortable descent rate, and controllability restrictions. The collective-lift stick provided precise glide slope tracking capability. The pilot preferred a deck-parallel attitude for which he used powered lift to control glide slope and pitch attitude to keep the angle of attack near zero. Workload was reduced when the deceleration schedule was delayed until the aircraft was well established on the glide slope, since thrust vector changes induced flight path disturbances.

Gerdes, R. M.↗

NASA NTRS1978

A computer program for estimation from incomplete multinomial data

Coding is given for maximum likelihood and Bayesian estimation of the vector p of multinomial cell probabilities from incomplete data. Also included is coding to calculate and approximate elements of the posterior mean and covariance matrices. The program is written in FORTRAN 4 language for the Control Data CYBER 170 series digital computer system with network operating system (NOS) 1.1. The program requires approximately 44000 octal locations of core storage. A typical case requires from 72 seconds to 92 seconds on CYBER 175 depending on the value of the prior parameter.

Credeur, K. R.↗

NASA NTRS1981

STAR adaptation of QR algorithm

The QR algorithm used on a serial computer and executed on the Control Data Corporation 6000 Computer was adapted to execute efficiently on the Control Data STAR-100 computer. How the scalar program was adapted for the STAR-100 and why these adaptations yielded an efficient STAR program is described. Program listings of the old scalar version and the vectorized SL/1 version are presented in the appendices. Execution times for the two versions applied to the same system of linear equations, are compared.

Shah, S. N.↗

NASA NTRS1982

Tests of a D vented thrust deflecting nozzle behind a simulated turbofan engine

A D vented thrust deflecting nozzle applicable to subsonic V/STOL aircraft was tested behind a simulated turbofan engine in the verticle thrust stand. Nozzle thrust, fan operating characteristics, nozzle entrance conditions, and static pressures were measured. Nozzle performance was measured for variations in exit area and thrust deflection angle. Six core nozzle configurations, the effect of core exit axial location, mismatched core and fan stream nozzle pressure ratios, and yaw vane presence were evaluated. Core nozzle configuration affected performance at normal and engine out operating conditions. Highest vectored nozzle performance resulted for a given exit area when core and fan stream pressure were equal. Its is concluded that high nozzle performance can be maintained at both normal and engine out conditions through control of the nozzle entrance Mach number with a variable exit area.

Watson, T. L.↗

NASA NTRS1998

A Compendium of Wind Statistics and Models for the NASA Space Shuttle and Other Aerospace Vehicle Programs

The wind profile with all of its variations with respect to altitude has been, is now, and will continue to be important for aerospace vehicle design and operations. Wind profile databases and models are used for the vehicle ascent flight design for structural wind loading, flight control systems, performance analysis, and launch operations. This report presents the evolution of wind statistics and wind models from the empirical scalar wind profile model established for the Saturn Program through the development of the vector wind profile model used for the Space Shuttle design to the variations of this wind modeling concept for the X-33 program. Because wind is a vector quantity, the vector wind models use the rigorous mathematical probability properties of the multivariate normal probability distribution. When the vehicle ascent steering commands (ascent guidance) are wind biased to the wind profile measured on the day-of-launch, ascent structural wind loads are reduced and launch probability is increased. This wind load alleviation technique is recommended in the initial phase of vehicle development. The vehicle must fly through the largest load allowable versus altitude to achieve its mission. The Gumbel extreme value probability distribution is used to obtain the probability of exceeding (or not exceeding) the load allowable. The time conditional probability function is derived from the Gumbel bivariate extreme value distribution. This time conditional function is used for calculation of wind loads persistence increments using 3.5-hour Jimsphere wind pairs. These increments are used to protect the commit-to-launch decision. Other topics presented include the Shuttle Shuttle load-response to smoothed wind profiles, a new gust model, and advancements in wind profile measuring systems. From the lessons learned and knowledge gained from past vehicle programs, the development of future launch vehicles can be accelerated. However, new vehicle programs by their very nature will require specialized support for new databases and analyses for wind, atmospheric parameters (pressure, temperature, and density versus altitude), and weather. It is for this reason that project managers are encouraged to collaborate with natural environment specialists early in the conceptual design phase. Such action will give the lead time necessary to meet the natural environment design and operational requirements, and thus, reduce development costs.

Smith, O. E.↗

NASA NTRS2006

On the Extraction of Angular Velocity from Attitude Measurements

In this paper we research the extraction of the angular rate vector from attitude information without differentiation, in particular from quaternion measurements. We show that instead of using a Kalman filter of some kind, it is possible to obtain good rate estimates, suitable for spacecraft attitude control loop damping, using simple feedback loops, thereby eliminating the need for recurrent covariance computation performed when a Kalman filter is used. This considerably simplifies the computations required for rate estimation in gyro-less spacecraft. Some interesting qualities of the Kalman filter gain are explored, proven and utilized. We examine two kinds of feedback loops, one with varying gain that is proportional to the well known Q matrix, which is computed using the measured quaternion, and the other type of feedback loop is one with constant coefficients. The latter type includes two kinds; namely, a proportional feedback loop, and a proportional-integral feedback loop. The various schemes are examined through simulations and their performance is compared. It is shown that all schemes are adequate for extracting the angular velocity at an accuracy suitable for control loop damping.

Bar-Itzhack, I. Y.↗

NASA NTRS2006

Rigid Body Rate Inference from Attitude Variation

Bar-Itzhack, I. Y.↗

NASA NTRS2009

Generating Ka-Band Signals Using an X-Band Vector Modulator

A breadboard version of a transmitter for radio communication at a carrier frequency of 32 GHz (which is in the Ka band) utilizes a vector modulator operating at a carrier frequency of 8 GHz (the low end of the X band) to generate any of a number of advanced modulations that could include amplitude and/or phase modulation components. The 8-GHz modulated signal is mixed with a 24-GHz signal generated by an upconverter to obtain the desired 32-GHz modulated output. The transmitter is being developed as a prototype of downlink transmitters for transmission of data from spacecraft to Earth at high rates (>100 Mb/s). The transmitter design could also be adapted to terrestrial and Earth/satellite communication links. The advanced modulations (which can include M-ary phase-shift keying (M-PSK), offset phase-shift keying (OPSK), and M-ary quadrature amplitude modulation (M-QAM). These modulations are needed because for a given amount of signal bandwidth, they enable transmission of data at rates greater than those of older, simpler modulation schemes. The transmitter architecture (see figure) was chosen not only to enable generation of the required modulations at 32 GHz but also to reduce the number of components needed to implement the transmitter. Instead of incorporating an 8-GHz signal source, the transmitter utilizes an 8-GHz signal generated by a voltage-controlled oscillator that is part of an X-band transponder with which the fully developed version of this transmitter would be used in the original intended spacecraft application. The oscillator power is divided onto two paths, one of which goes through the vector modulator, the other through amplifiers and a 3 frequency multiplier. Band-pass filters are included downstream of the frequency multiplier to suppress unwanted harmonics.

Smith, Scott↗

NASA NTRS1991

Solar control of the earth's emission of energetic O(+)

Energetic (0.1-16 keV/e) O(+) data obtained in the earth's plasma sheet (between 10 and 23 RE) by an ion mass spectrometer on the ISEE-1 spacecraft are compared statistically with published data on the concurrent solar wind and IMF. The most strongly variable parameter of the plasma sheet O(+) is its density, which is found to be well correlated with certain solar wind parameters, especially with the solar wind flow speed and the IMF component perpendicular to the flow vector. When those two solar wind parameters are combined to form an electric field (-v x B), both the number density and the energy density of the O(+) are found to vary in proportion to the square of that electric field, on average, suggesting that the emission of energetic O(+) ions from the earth may be powered by that same field. Based on this and on the previously published correlation with solar activity, it is argued that the emission of O(+) is controlled by a combination of HF (ionizing) and quasi-static (accelerating) solar electromagnetic fields.

Lennartsson, W.↗

NASA NTRS1982

Population control of self-replicating systems

The literature concerning fibonacci sequence and the mathematics of self replication are reviewed. One option allows each primary to generate n-replicas, one in each sequential time frame after its own generation with no restrictions on the number of ancestors per replica. The state vector of the replicas in an efficient manner is determined. Option-B has a fixed number of replicas per primary and no restrictions on the number of ancestors for a replica. Any element fij represents the number of elements of type-j in time frame k+1 generated from type-i in time frame k. Option-D is a diagonal matrix whose eigenvalues are precisely those of f.

Mccord, R. L.↗

NASA NTRS1977

Instantaneous and time-averaged dispersion and measurement models for estimation theory applications with elevated point source plumes

Estimation theory, which originated in guidance and control research, is applied to the analysis of air quality measurements and atmospheric dispersion models to provide reliable area-wide air quality estimates. A method for low dimensional modeling (in terms of the estimation state vector) of the instantaneous and time-average pollutant distributions is discussed. In particular, the fluctuating plume model of Gifford (1959) is extended to provide an expression for the instantaneous concentration due to an elevated point source. Individual models are also developed for all parameters in the instantaneous and the time-average plume equations, including the stochastic properties of the instantaneous fluctuating plume.

Diamante, J. M.↗

NASA NTRS1983

Comparative assessment of LANDSAT-4 MSS and TM data quality for mapping applications in the southeast

The initial objectives of analyses of the MSS data are two-fold: (1) to evaluate the geodetic accuracy of CCT-P data of the test sites; and (2) to improve the geodetic accuracy by additional processing if the original data either do not meet pre-launch specifications or mapping requirements. The location of 45 ground control points (GCP) digitized from 35 U.S. Geological Survey 1:24,000 scale quadrangles (UTM coordinates) were identified in terms of pixel and scan line values. These 46 points are used to establish UTM position error vector distributions in the scene. As an initial check on the geometric reliability of the MSS data, 28 well-distributed GCPs were input to a program which compares the scaled image distances between all possible point pairs with the corresponding map distances and computes the distance differences; that is, the relative positional errors. The relative errors obtained from initial computations averaged about +/- 200 m. These errors could result from a number of sources, including misidentification of GCP locations, UTM coordinate errors introduced by the map digitizing process or errors resulting from data acquisition and geometric processing.

Welch, R.↗

NASA NTRS1990

Visible light emission excited by interaction of Space Shuttle exhaust with the atmosphere

Ground-based video photography of firings of Space Shuttle Primary Reaction Control System (PRCS) engines show optical emissions extending nearly 4 km form the vehicle after steady state is reached. The total intensity and spatial distribution of these emissions depend on the angle between the spacecraft velocity vector and the engine exhaust axis. Candidate sources for this radiation are reviewed and the conclusion is reached that it is most likely due to vibrationally excited OH, formed by the reaction of fast ambient O atoms and H2O molecules in the exhaust.

Murad, E.↗

NASA NTRS2004

A "Kane's Dynamics" Model for the Active Rack Isolation System Part Two: Nonlinear Model Development, Verification, and Simplification

Many microgravity space-science experiments require vibratory acceleration levels that are unachievable without active isolation. The Boeing Corporation's active rack isolation system (ARIS) employs a novel combination of magnetic actuation and mechanical linkages to address these isolation requirements on the International Space Station. Effective model-based vibration isolation requires: (1) An isolation device, (2) an adequate dynamic; i.e., mathematical, model of that isolator, and (3) a suitable, corresponding controller. This Technical Memorandum documents the validation of that high-fidelity dynamic model of ARIS. The verification of this dynamics model was achieved by utilizing two commercial off-the-shelf (COTS) software tools: Deneb's ENVISION(registered trademark), and Online Dynamics Autolev(trademark). ENVISION is a robotics software package developed for the automotive industry that employs three-dimensional computer-aided design models to facilitate both forward and inverse kinematics analyses. Autolev is a DOS-based interpreter designed, in general, to solve vector-based mathematical problems and specifically to solve dynamics problems using Kane's method. The simplification of this model was achieved using the small-angle theorem for the joint angle of the ARIS actuators. This simplification has a profound effect on the overall complexity of the closed-form solution while yielding a closed-form solution easily employed using COTS control hardware.

Beech, G. S.↗

NASA NTRS1977

Vectorization of linear discrete filtering algorithms

Linear filters, including the conventional Kalman filter and versions of square root filters devised by Potter and Carlson, are studied for potential application on streaming computers. The square root filters are known to maintain a positive definite covariance matrix in cases in which the Kalman filter diverges due to ill-conditioning of the matrix. Vectorization of the filters is discussed, and comparisons are made of the number of operations and storage locations required by each filter. The Carlson filter is shown to be the most efficient of the filters on the Control Data STAR-100 computer.

Schiess, J. R.↗

NASA NTRS1978

Approach guidance logic for a tilt-rotor aircraft

The distinctive feature of a tilt-rotor aircraft is that the pilot can change the rotor mast angles to go from a helicopter configuration for take-off and landing to an airplane configuration for high cruise speeds and vice-versa. An approach path for such an aircraft is proposed and the logic required to fly along this path in the presence of wind is determined. The main contribution of this work is an efficient and, to my knowledge, new method for generating the nominal state and control histories taking into account an estimate of the mean wind velocity and direction. The method requires the solution of algebraic (mostly linear) equations to generate a 'universal nominal', and feedforward and feedback gains. Then, in flight the additional state and control corrections due to deviation in descent rate, deceleration, and flight in a steady wind are obtained by multiplying simple precalculated functions of time by descent rate, deceleration or sine and cosine components of the mean wind vector. Simulations of approach flights for different wind conditions, assuming perfect state information in the feedback signal, indicated satisfactory performance.

Beser, J.↗

NASA NTRS1990

The origin of fluvial valleys and early geologic history, Aeolis Quadrangle, Mars

A valley genesis model of the southern Aeolis Quadrangle, eastern Mars, is proposed. In response to widespread effusive volcanism in interstratified, ice-reach terrains, local subsidence occurred along fractures/faults, and produced scarps that intersected local aquifers. Heated spring discharges issuing from these scarps may have carved the valleys through a combination of downvalley water, ice, and debris flows, and headward erosion along stratal discontinuities and individual conduit faults and fractures. Fifty-six asymmetric scarps or ridges that are probable thrust faults are mapped. The faults exhibit an orientation vector mean of N 63 deg W +/- 11 deg and they transect the lava plains and the older plateau sequence units. The vector mean for the 264 valleys mapped is N 48 deg W +/- 12 deg, with a larger dispersion about the mean. The similar orientations displayed by thrust faults and valley axes suggest that valley locations are partly controlled by preexisting thrust faults and fracture systems.

Brakenridge, G. Robert↗