Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Flame Speeds of Methane-Air, Propane-Air, and Ethylene-Air Mixtures at Low Initial Temperatures

Flame speeds were determined for methane-air, propane-air, and ethylene-air mixtures at -73 C and for methane-air mixtures at -132 C. The data extend the curves of maximum flame speed against initial mixture temperature previously established for the range from room temperature to 344 C. Empirical equations for maximum flame speed u(cm/ sec) as a function of initial mixture temperature T(sub O) were determined to be as follows: for methane, for T(sub O) from 141 to 615 K, u = 8 + 0.000160 T(sub O)(exp 2.11); for propane, for T(sub O) from 200 to 616 K, u = 10 + 0.000342 T(sub O)(exp 2.00); for ethylene, for T(sub O) from 200 to 617 K, u = 10 + 0.00259 T(sub O)(exp 1.74). Relative flame speeds at low initial temperatures were predicted within approximately 20 percent by either the thermal theory as presented by Semenov or by the diffusion theory of Tanford and Pease. The same order was found previously for high initial temperatures. The low-temperature data were also found to extend the linear correlations between maximum flame speed and calculated equilibrium active-radical concentrations, which were established by the previously reported high-temperature data.

Dugger, Gordon L↗
NASA NTRS1994

Optical processing for semiconductor device fabrication

A new technique for semiconductor device processing is described that uses optical energy to produce local heating/melting in the vicinity of a preselected interface of the device. This process, called optical processing, invokes assistance of photons to enhance interface reactions such as diffusion and melting, as compared to the use of thermal heating alone. Optical processing is performed in a 'cold wall' furnace, and requires considerably lower energies than furnace or rapid thermal annealing. This technique can produce some device structures with unique properties that cannot be produced by conventional thermal processing. Some applications of optical processing involving semiconductor-metal interfaces are described.

Sopori, Bhushan L.↗
NASA NTRS2000

Gravity-Related Transport Process in Off-Axis Sputtering Deposition

In the synthesis of epitaxial oxide films, reactive off-axis sputtering deposition techniques have demonstrated the advantages of fabricating high quality epitaxial films. Due to the collisions between the sputtered species and the residue gases, the kinetic energy of species was reduced and the transport of depositing species changed from a ballistic movement to a diffusive drift in which the transport species were almost thermalized. A gravity effect could appear in the transport process. Three transport regimes were observed when the growth pressures vary from 5 mTorr to 150 mTorr. Film growth rate, depositing orientations, crystal structure, surface morphology, and compositions were characterized. A gravity related phenomenon was revealed in film growth at the relative low growth pressures.

Zhu, Shen↗
NASA NTRS2005

Self-consistent Evolution of Cosmic-Ray Shocks

Several key accomplishments were achieved under this grant. In the first year we combined our novel adaptive mesh refinement code for diffusive shock acceleration with the implementation of the Malkov/Volk thermal leakage injection model to produce an extremely powerful new modeling tool. We used it to examine the time evolution of highly modified CR shocks in a systematic way, finding that characteristic proton injection efficiencies for strong quasi-parallel shocks should be a few parts in l0(exp -4). That is sufficient for even moderately strong shocks to become efficient CR accelerators and substantially modified in structure. Those results were published in the Astrophysical Journal.

Jones, Thomas W.↗
NASA NTRS2008

Development and Characterization of the Bonding and Integration Technologies Needed for Fabricating Silicon Carbide Based Injector Components

Advanced ceramic bonding and integration technologies play a critical role in the fabrication and application of silicon carbide based components for a number of aerospace and ground based applications. One such application is a lean direct injector for a turbine engine to achieve low NOx emissions. Ceramic to ceramic diffusion bonding and ceramic to metal brazing technologies are being developed for this injector application. For the diffusion bonding technology, titanium interlayers (coatings and foils) were used to aid in the joining of silicon carbide (SiC) substrates. The influence of such variables as surface finish, interlayer thickness, and processing time were investigated. Electron microprobe analysis was used to identify the reaction formed phases. In the diffusion bonds, an intermediate phase, Ti5Si3Cx, formed that is thermally incompatible in its thermal expansion and caused thermal stresses and cracking during the processing cool-down. Thinner interlayers of pure titanium and/or longer processing times resulted in an optimized microstructure. Tensile tests on the joined materials resulted in strengths of 13-28 MPa depending on the SiC substrate material. Nondestructive evaluation using ultrasonic immersion showed well formed bonds. For the joining technology of brazing Kovar fuel tubes to silicon carbide, preliminary development of the joining approach has begun. Various technical issues and requirements for the injector application are addressed.

Halbig,Michael C.↗
NASA NTRS2009

Using Dome C for Moderate Resolution Imaging Spectroradiometer Calibration Stability and Consistency

Currently, there are two nearly identical moderate resolution imaging spectroradiometer (MODIS) instruments operated in space: one on the Terra spacecraft launched in December 1999 and another on the Aqua spacecraft launched in May 2002. MODIS has 36 spectral bands with wavelengths covering from visible (VIS) to long-wave infrared (LWIR). Since launch, M0DIS observations and data products have significantly enabled studies of changes in the Earth system of land, oceans, and atmosphere. In order to maintain its on-orbit calibration and data product quality, MODIS was built with a comprehensive set of on-board calibrators. MODIS reflective solar bands (RSB) are calibrated on-orbit by a system that consists of a solar diffuser (SD) and a solar diffuser stability monitor(SDSM) on a regular basis. Its thermal emissive bands (TEB) calibration is executed on a scan-by-scan basis using an on-board blackbody (BB). The MODIS Characterization Support Team (MCST) at NASA/GSFC has been responsible for supporting sensor calibration and characterization tasks from pre-launch to post launch. In this paper,we describe current MCST efforts and progress made to examine sensor stability and intercalibration consistency using observations over Dome Concordia, Antarctica. Results show that this site can provide useful calibration reference for Earth-observing sensors.

Xiong, Xiaoxiong↗
NASA NTRSDate not supplied

Delamination Depth Imaging for Quasi-Static and Fatigue Load Testing Using Passive Thermography

Passive thermography is used to monitor small increases in temperature resulting from delamination damage formation in composite hat-stiffened panels during both quasi-static and fatigue loading. It has been observed that rapid damage formation produces heating. This is composed of two heat generation components. The first component is an instantaneous response due to an irreversible thermoelastic strain release. The second component is mechanical heating, at the interface of failure, due to fracture damage. This produces a transient rise in temperature as the heat diffuses to the surface. The first component defines the thermal start time for the transient response. A one-dimensional thermal model is fitted to the data pixel by pixel, to produce imagery of the damage depth. The results are compared to ultrasonic and X-ray CT data.

Passive thermography↗
NASA NTRS1977

Significance of vegetation in interpreting thermal radiation from a terrestrial surface

The regions between crop rows are modeled as infinitely long diffuse cavities. Geometrical view factors are calculated, accounting for reflected radiation emanating internal to the cavity and from the background sky. A 'cavity' emissivity dependent on local geometry is defined to allow for correcting apparent temperatures to true temperatures. The total emissivity appropriate for correcting aircraft thermal data is then calculated by averaging all emissivity components to account for soil, crop, and background. It is shown that even for the lowest crop and vegetation emissivities, if the crop height-to-spacing ratio is greater than unity, the composite emissivity is greatly increased, giving rise to a decreased error in remotely sensed temperature data.

Sutherland, R. A.↗
NASA NTRS1981

Diffusion of cold magnetospheric ions

The paper investigates conditions under which a diffusion equation is a valid description of the transport across magnetic field lines of low energy magnetospheric plasma. The case in which the guiding center drift and its fluctuating component are comparable in size to the particle thermal speed is considered. It is concluded that a two-dimensional diffusion equation is valid in the alpha-beta space of the Euler potentials, provided that the fluctuations have a short enough correlation time so that the guiding center drifts remain negligible, and ions in Jupiter's Io plasma torus can thus be described by a diffusion equation if the correlation time is no more than a few rotation periods of the planet.

Birmingham, T. J.↗
DOE OSTI2024

Spin-caloric resistance of Dirac plasma in a graphene Corbino device

The thermal resistance of a spin-polarized hydrodynamic Dirac plasma in graphene is considered. Here, a mechanism for the coupling of heat and spin flows is discussed, demonstrating that spin diffusion and spin thermocurrent modify viscous dissipation, leading to a significant enhancement of thermal resistance. Practical calculations are then presented for graphene devices in the Corbino geometry.

Graphene↗
DOE OSTI2020

Pre-Symptomatic COVID Screening

Temperature checks for fever are extensively used for preliminary COVID screenings but are ineffective during the incubation stage of infection when a person is asymptotic. Researchers at the European Centre for Disease Prevention and Control concluded that approximately 75% of passengers infected with COVID-19 and traveling from affected Chinese cities would not be detected by early screening. Core body temperature is normally kept within a narrow range and has the smallest relative standard deviation of all vital signs. Heat in the body is prioritized around internal organs at the expense of the periphery by controlling blood flow. In fact, blood flow to the skin may vary by a factor of 100 depending on thermal conditions. This adaptation causes rapid temperature fluctuations in different skin regions from changes in cardiac output, metabolism, and likely cytokine diffusion during inflammation that would not be seen in average core body temperature. Current IR and thermal scanners used for temperature checks are not necessarily reflective of core body temperatures and require cautious interpretation as they frequently result in false positive and false negative diagnosis. Hand held thermometers measure average skin temperatures and can get readings that differ from core body temperature by as much as 7°. Rather than focusing on a core body temperature threshold assessment we believe that variability of temperature patterns using a novel wearable transdermal microneedle sensor will be more sensitive to infections in the incubation stage and propose to develop a wearable transdermal temperature sensor using established Sandia microneedle technology for pre-symptomatic COVID screening that can additionally be used to monitor disease progression at later stages.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Pre Symptomatic COVID Screening

Temperature checks for fever are extensively used for preliminary COVID screenings but are ineffective during the incubation stage of infection when a person is asymptotic. Researchers at the European Centre for Disease Prevention and Control concluded that approximately 75% of passengers infected with COVID-19 and traveling from affected Chinese cities would not be detected by early screening. Core body temperature is normally kept within a narrow range and has the smallest relative standard deviation of all vital signs. Heat in the body is prioritized around internal organs at the expense of the periphery by controlling blood flow. In fact, blood flow to the skin may vary by a factor of 100 depending on thermal conditions. This adaptation causes rapid temperature fluctuations in different skin regions from changes in cardiac output, metabolism, and likely cytokine diffusion during inflammation that would not be seen in average core body temperature. Current IR and thermal scanners used for temperature checks are not necessarily reflective of core body temperatures and require cautious interpretation as they frequently result in false positive and false negative diagnosis. Hand held thermometers measure average skin temperatures and can get readings that differ from core body temperature by as much as 7°. Rather than focusing on a core body temperature threshold assessment we believe that variability of temperature patterns using a novel wearable transdermal microneedle sensor will be more sensitive to infections in the incubation stage and propose to develop a wearable transdermal temperature sensor using established Sandia microneedle technology for pre symptomatic COVID screening that can additionally be used to monitor disease progression at later stages.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Examining normal modes as fundamental heat carriers in amorphous solids: The case of amorphous silicon

Normal mode decomposition of atomic vibrations has been used to provide microscopic understanding of thermal transport in amorphous solids for decades. In normal mode methods, it is naturally assumed that atoms vibrate around their equilibrium positions, and that individual normal modes are the fundamental vibrational excitations transporting heat. With the abundance of predictions from normal mode methods and experimental measurements now available, we carefully analyze these calculations in amorphous silicon, a model amorphous solid. We find a number of discrepancies, suggesting that treating individual normal modes as fundamental heat carriers may not be accurate in amorphous solids. Furthermore, our classical and ab initio molecular dynamics simulations of amorphous silicon demonstrate a large degree of atomic diffusion, especially at high temperatures, leading to the conclusion that thermal transport in amorphous solids could be better described starting from the perspectives of liquid physics rather than from crystalline solids.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Solute diffusion behavior during heat treatment and its impact in Sc-microalloyed Al-Cu system

Scandium (Sc) is a promising microalloying element that enhances the strength and thermal stability of aluminum (Al) alloys. However, these benefits are not fully realized in aluminum-copper (Al-Cu) systems, and corrosion resistance often declines due to the complex phase evolution and diffusion behavior of Cu and Sc. Here, to clarify this, solute diffusion behavior and Cu-Sc interaction during heat treatment (HT) were investigated using in situ synchrotron-based transmission x-ray microscopy (TXM), wide-angle x-ray scattering (WAXS), and x-ray absorption near-edge structure (XANES) spectroscopy. The results, supported by electron microscopy, reveal strong Cu-Sc bonding that significantly impedes solute diffusion, leading to inhomogeneous solute distribution and non-uniform precipitation. Moreover, the Al-Cu-Sc eutectic phase exhibits high thermal stability, resisting dissolution even near the matrix liquidus. These findings quantitatively elucidate the sluggish diffusion kinetics of Cu and Sc, which can help redesign HT schedules to improve both mechanical properties and corrosion resistance in Sc-microalloyed Al-Cu alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

In Situ Atomic Tracking on the Interfacial Etching and Reconfiguration of Cu-ReSe 2 Contact during Thermal Annealing

The Schottky barrier height can be greatly affected by the metal diffusion, reaction, and covalent bonding formation at the contact. Exploring novel methods and revealing the fundamental mechanisms for contact engineering are of vital importance for microelectronic devices. Here, in this study, the annealing induced interfacial reactions at Cu-ReSe 2 contact are dynamically revealed from the atomic scale. Accompanied by the diffusion of Se to Cu, ReSe 2 is gradually decomposed to a thin Re interlayer through a “chain-by-chain” manner. Theoretical calculations show that the Cu atoms can facilitate the chemical bond breaking of ReSe 2 , significantly lowering the Se diffusion energy barrier toward Cu. The formed Re/ReSe 2 heterostructure presents a metal-like band structure, which underscores the critical role of Cu in altering the interfacial chemistry and promoting carrier transport across the interface. Our results can provide vital insights into the contact properties of ReSe 2 and provide a possible method for fabricating high-performance ReSe 2 -based devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1985

Mass transfer across combustion gas thermal boundary layers - Power production and materials processing implications

The effects of Soret diffusion (for vapors) and thermophoresis (for particles) are illustrated using recent optical experiments and boundary layer computations. Mass transfer rate augmentations of up to a factor of 1000 were observed and predicted for submicron-particle capture by cooled solid surfaces, while mass transfer suppressions of more than 10 to the -10th-fold were predicted for 'overheated' surfaces. It is noted that the results obtained are of interest in connection with such technological applications as fly-ash capture in power generation equipment and glass droplet deposition in optical-waveguide manufacture.

Rosner, D. E.↗
NASA NTRS1996

Salt-Finger Convection in a Stratified Fluid Layer Induced by Thermal and Solutal Capillary Motion

Salt-finger convection in a double-diffusive system is a motion driven by the release of gravitational potential due to different diffusion rates. Normally, when the gravitational field is reduced, salt-finger convection together with other convective motions driven by buoyancy forces will be rapidly suppressed. However, because the destabilizing effect of the concentration gradient is amplified by the Lewis number, with values varying from 10(exp 2) for aqueous salt solutions to 10 (exp 4) for liquid metals, salt-finger convection may be generated at much reduced gravity levels. In the microgravity environment, the surface tension gradient assumes a dominant role in causing fluid motion. In this paper, we report on some experimental results showing the generation of salt-finger convection due to capillary motio on the surface of a stratified fluid layer. A numerical simulation is presented to show the cause of salt-finger convection.

Chen, Chuan F.↗
NASA NTRS2007

Fabrication and Characterization of Diffusion Bonds for Silicon Carbide

Diffusion bonds of silicon carbide (SiC) were fabricated using several different types of titanium (Ti) based interlayers between the SiC substrates. The interlayers were an alloyed Ti foil, a pure Ti foil, and a physically vapor deposited (PVD) Ti coating. Microscopy was conducted to evaluate the cross-sections of the resulting bonds. Microprobe analysis identified reaction formed phases in the diffusion bonded region. Uniform and well adhered bonds were formed between the SiC substrates. In the case where the alloyed Ti foil or a thick Ti coating (i.e. 20 micron) was used as the interlayer, microcracks and several phases were present in the diffusion bonds. When a thinner interlayer was used (i.e. 10 micron PVD Ti), no microcracks were observed and only two reaction formed phases were present. The two phases were preferred and fully reacted phases that did not introduce thermal stresses or microcracks during the cool-down stage after processing. Diffusion bonded samples were evaluated with the non-destructive evaluation (NDE) methods of pulsed thermography and immersion ultrasonic testing. Joined SiC substrates that were fully bonded and that had simulated bond flaws in the interlayer were also evaluated using immersion ultrasound. Pull testing was conducted on the bonds to determine the tensile strength. To demonstrate the joining approach for a complex multilayered component for a low NOx injector application, the diffusion bonding approach was used to join three 4" diameter SiC discs that contained complex fuel and air flow channels.

Halbig, Michael↗