SEARCH · Engineering Papers

Results for “shear testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Flight-management strategies for escape from microburst encounters

An effort is underway by NASA, FAA, and industry to reduce the threat of convective microburst wind shear phenomena to aircraft. The goal is to develop and test a candidate set of strategies for recovery from inadvertent microburst encounters during takeoff. Candidate strategies were developed and evaluated using a fast-time simulation consisting of a simple point-mass performance model of a transport-category airplane and an analytical microburst model. The results indicate that the recovery strategy characteristics that best utilize available airplane energy include an initial reduction in pitch attitude to reduce the climb rate, followed by an increase in pitch up to the stick shaker angle of attack. The stick shaker angle of attack should be reached just as the airplane is exiting the microburst. The shallowest angle of climb necessary for obstacle clearance should be used. If the altitude is higher than necessary, an intentional descent to reduce the airspeed deceleration should be used. Of the strategies tested, two flight-path-angle based strategies had the highest recovery altitudes and the least sensitivity to variations in the encounter scenarios.

Hinton, David A.↗

NASA NTRS1958

Handbook of structural stability part VI : strength of stiffened curved plates and shells

A comprehensive review of failure of stiffened curved plates and shells is presented. Panel instability in stiffened curved plates and general instability of stiffened cylinders are discussed. The loadings considered for the plates are axial, shear, and the combination of the two. For the cylinders, bending, external pressure, torsion, transverse shear, and combinations of these loads are considered. When possible, test data and theory were correlated. General instability in stiffened cylinders was investigated. For bending and torsion loads, test data and theory were correlated. For external pressure several existing theories were compared. As a result of this investigation a unified theoretical approach to analysis of general instability in stiffened cylinders was developed. (author)

Becker, Herbert↗

NASA NTRS1943

Some Investigations of the General Instability of Stiffened Metal Cylinders VI : Stiffened Metal Cylinders Subjected to Combined Bending and Transverse Shear

This is the sixth of a series of reports covering an investigation of the general instability problem by the California Institute of Technology. The first five reports of this series cover investigations of the general instability problem under the loading conditions of pure bending and were prepared under the sponsorship of the Civil Aeronautics Administration. This report and the succeeding reports of this series cover the work done on other loading conditions under the sponsorship of the National Advisory Committee for Aeronautics. This report summarizes the work that has been carried on in the experimental investigation of the problem of general instability of stiffened metal cylinders subjected to combined bending and transverse shear at the C.I.T. This part of the investigation includes tests on 55 sheet-covered specimens.

TESTING MACHINES↗

NASA NTRS2001

Fracture Behavior of a Stitched Warp-Knit Carbon Fabric Composite

Tests were conducted on several types of fracture specimens made from a carbon/epoxy composite. The composite material was stitched prior to introducing epoxy resin. Boeing, used this material to develop a composite wing box for a transport aircraft in the NASA Advanced Composites Transport Program. The specimens included compact, extended compact, and center notched tension specimens. The specimens were cut from panels with three orientations in order to explore the effects of anisotropy. The panels were made with various thicknesses to represent a wing, skin from tip to root. All fractures were not self-similar depending on specimen type and orientation. Unnotched tension specimens were also tested to measure elastic constants and strengths. The normal and shear strains were calculated on fracture planes using a series representation of strain fields for plane anisotropic crack problems. The fracture parameters were determined using a finite element method. Characteristic distances for critical tension and shear strains were calculated for each specimen and a failure criterion based on the interaction of tension and shear strains was proposed.

Poe, Clarence C., Jr.↗

NASA NTRS1999

Experiment Verification of the Analytical Methodology to Predict the Residual Strength of Metallic Shell Structure

Experimental and analysis results for a curved, stiffened aluminum fuselage panel tested in a combined loads test machine with combined internal pressure, axial compression, and torsional shear loads are described. The experimental and analytical strain results for the panel with and without discrete source damage are presented. The effect of notch tip geometry on crack growth predictions is addressed. The crack growth trajectory predictions for the panel are presented for the applied loading conditions at failure.

Starnes, James H., Jr.↗

NASA NTRS2004

The Sensitivity of Simulated Storm Structure and Intensity to the Temperature at the Lifted Condensation Level

Prior parameter space studies of simulated deep convection are extended to embrace variations in the ambient temperature at the Lifted Condensation Level (LCL). Within the context of the parameter space study design, changes in LCL temperature are roughly equivalent to changes in the ambient precipitable water. Two series of simulations are conducted, one with a warm LCL that is associated with approximately 60 mm of precipitable water, and another with LCL temperatures 8 C cooler, so that PW is reduced to roughly 30 mm. The sets of simulations include tests of the impact of changes in the buoyancy and shear profile shapes and of changes in mixed and moist layer depths, all of which have been shown to be important in prior work. Simulations discussed here feature values of bulk convective available potential energy (CAPE) of 800, 2000, or 3200 Joules per kilogram, and a single semicircular hodograph having radius of 12 meters per second, but with variable vertical shear. The simulations reveal a consistent trend toward stronger peak updraft speeds for the cooler LCL temperature (reduced PW) cases, if all other environmental parameters are held constant. Roughly comparable increases in updraft speeds are noted for all combinations of LCL and level of free convection heights. These increases in updraft strength are evidently the result of both the reduction of condensate loading aloft and the lower altitudes at which the latent heat release by freezing and deposition commences in the cooler, low-PW environments. Because the latent heat of fusion adds relatively more energy to the updrafts at low CAPE, those storms show more strengthening at low PW than do the larger CAPE storms. As expected, maximum storm precipitation rates tend to diminish as PW is decreased, but only slightly, and by amounts not proportionate to the decrease in PW. The low-PW cases thus actually feature larger environment-relative precipitation efficiency than do the high-PW cases. In addition, more hail reaches the surface in the low-PW cases because of reduced melting in the cooler environments.

McCaul, Eugene W., Jr.↗

NASA NTRS2020

Mechanical twinning of monazite expels radiogenic Pb

Mechanical twins form by the simple shear of the crystal lattice during deformation In order to test the potential of narrow twins in monazite to record the timing of their formation, a ~1,700 Ma monazite grain deformed at ~980 Ma was investigated by electron backscattered diffraction (EBSD), transmission electron microscopy (TEM) and atom probe tomography (APT). APT 208Pb/232Th ages indicate that the twin was entirely reset by radiogenic Pb-loss during its formation at conditions far below the monazite closure temperature. The results are consistent with a model where Pb is liberated during rupture of REE-O bonds in the large REEO9 polyhedra during twinning. Liberated Pb is likely to migrate along fast diffusion pathways such as crystal defects. The combination of a quantitative microstructural investigation and nanogeochronology provides a new approach for understanding the history of accessory phases.

monazite↗

NASA NTRS1972

Experimental investigation of strains in fabric under biaxial and shear forces.

The paper defines the experimental phase of an objective to obtain the mechanical characteristics and coefficients required by the generalized form of Hooke's law for nylon-polyurethane-coated fabric. Test specimens were cylindrical fabric sleeves and were loaded in axial tension by an Instron, in hoop tension by pressurizing, and in shear by a torquing fixture. An extensive amount of strain data is included for a wide combination of the three membrane loads. The tests indicate highly nonlinear stress-strain characteristics of the fabric and a strong dependency on all three membrane loads.

Alley, V. L., Jr.↗

DOE OSTI2024

In Situ Study on Fracture Behavior of Thick-Section Friction Stir-Welded AA 5083 Alloy

Friction stir welding (FSW) produces a gradient microstructure with distinct metallurgical zones. Here, the present study focuses on characterizing the fracture behavior during uniaxial loading across thick-section FSW joint in nonheat-treatable 5083 aluminum alloy. The hardness variation is linked to microstructural features across the weld zones through correlative microscopy. Notably, the heat-affected zone (HAZ) exhibits a lower hardness of 75 HV, while the thermomechanically affected zone (TMAZ) and stir zones (SZ) display a hardness of around 79HV. A marginal difference in hardness in HAZ prompts strain localization in HAZ on the advancing side of the weld, resulting in offset in fracture from the SZ, which is captured through in situ monitoring of the tensile test. Further, the postdeformation analysis reveals crack propagation along the maximum shear stress plane due to the coalescence of microvoids resulting from the fracturing and debonding of second-phase particles. Overall, this study provides valuable insight for optimizing the FSW process of AA 5083 alloy for thick-section applications.

36 MATERIALS SCIENCE↗

NASA NTRS2008

Terrestrial Planet Finder, Planet Detection Test-Bed: Latest Results of Planet Light Detection in the Presence of Starlight

The Terrestrial Planet Finder, Planet Detection Test-bed is a lab based simulation of the optics and control systems for the Terrestrial Planet Finder Interferometer mission. The test-bed supports starlight nulling at 10um infrared wavelengths, with fringe tracking at 2um wavelengths and angle and shear tracking at visible wavelengths. It further allows injection of simulated planet light in the presence of the nulled star light, to allow testing of planet detection methods. We will describe the detailed construction and operation of the test-bed from an optical and control system perspective. We will also report the latest results for narrow band nulls, and the detection of broad band planet light in the presence of nulled starlight.

Interferometry↗

DOE OSTI2020

Evaluation of a Robust, In-Situ Surface Treatment for Pipeline Solids Deposition Mitigation in Flowing Systems

Abstract The formation/precipitation and deposition of pipeline solids, such as gas hydrates, asphaltenes, and waxes have long plagued production fields. Given the vast differences in chemistries of these solids, any current prevention or mitigation strategy, particularly for cases where multiple issues are a concern, is likely to involve an extensive assortment of undefined chemical additives that are both costly and add complexity to the system. Surface treatments (coatings), on the other hand, present a relatively new viable option for management strategies. A chemically and physically robust surface treatment with the ability to address deposition issues for multiple pipeline solids could not only decrease the operating expenditures for a field through material cost savings and obviation of downstream separation, but could also simplify produced fluids by eliminating additional chemicals from the mixture. The purpose of this study is to explore the feasibility of a particular surface treatment as part of a solids management strategy. This work utilizes an omniphobic surface treatment to probe its effects on gas hydrate, asphaltene, and wax deposition. Specifically, high pressure rocking cells are employed to study gas hydrate nucleation and deposition. A bench-scale flowloop filled with crude oil and heptane is used to quantify the deposition of crude oil and asphaltenes after a set time period. Lastly, a mechanical shear device measures the adhesion force of wax deposits on untreated/treated surfaces. The gas hydrate rocking cell tests demonstrate an increase in induction time and occasional elimination of hydrate nucleation with the surface treatment. Moreover, the same apparatus indicates that the critical shear to avoid hydrate deposition may be lowered in the presence of the surface treatment compared to untreated pristine carbon steel coupons. A custom-built asphaltene flowloop then establishes that this surface treatment is effective in dramatically reducing the deposition of the aliphatic components of a crude oil, with a moderate reduction in the asphaltene fraction. Finally, mechanical adhesion force measurements for solidified paraffin wax display trends in agreement with the asphaltene results. The surface treatment on both pristine and corroded surfaces is able to reduce the adhesion of wax deposits to values below a pristine, untreated surface.

03 NATURAL GAS↗

NASA NTRS1995

Fatigue Crack Growth and Crack Bridging in SCS-6/Ti-24-11

Interfacial damage induced by relative fiber/matrix sliding was found to occur in the bridged zone of unidirectional SCS-6/Ti-24Al-11Nb intermetallic matrix composite specimens subjected to fatigue crack growth conditions. The degree of interfacial damage was not uniform along the bridged crack wake. Higher damage zones were observed near the machined notch in comparison to the crack tip. The interfacial friction shear strength tau(sub f) measured in the crack wake using pushout testing revealed lower values than the as-received interface. Interfacial wear also reduced the strength of the bridging fibers. The reduction in fiber strength is thought to be a function of the magnitude of relative fiber/matrix displacements ind the degree of interfacial damage. Furthermore, two different fiber bridging models were used to predict the influence of bridging on the fatigue crack driving force. The shear lag model required a variable tau(sub f) in the crack wake (reflecting the degradation of the interface) before its predictions agreed with trends exhibited by the experimental data. The fiber pressure model did an excellent job in predicting both the FCG data and the DeltaCOD in the bridged zone even though it does not require a knowledge of tau(sub f).

Ghosn, Louis J.↗

NASA NTRS2013

Testing of Advanced Conformal Ablative TPS

In support of the CA250 project, this paper details the results of a test campaign that was conducted at the Ames Arcjet Facility, wherein several novel low density thermal protection (TPS) materials were evaluated in an entry like environment. The motivation for these tests was to investigate whether novel conformal ablative TPS materials can perform under high heat flux and shear environment as a viable alternative to rigid ablators like PICA or Avcoat for missions like MSL and beyond. A conformable TPS over a rigid aeroshell has the potential to solve a number of challenges faced by traditional rigid TPS materials (such as tiled Phenolic Impregnated Carbon Ablator (PICA) system on MSL, and honeycomb-based Avcoat on the Orion Multi Purpose Crew Vehicle (MPCV)). The compliant (high strain to failure) nature of the conformable ablative materials will allow better integration of the TPS with the underlying aeroshell structure and enable monolithic-like configuration and larger segments to be used in fabrication.A novel SPRITE1 architecture, developed by the researchers at NASA Ames was used for arcjet testing. This small probe like configuration with 450 spherecone, enabled us to test the materials in a combination of high heat flux, pressure and shear environment. The heat flux near the nose were in the range of 500-1000 W/sq cm whereas in the flank section of the test article the magnitudes were about 50 of the nose, 250-500W/sq cm range. There were two candidate conformable materials under consideration for this test series. Both test materials are low density (0.28 g/cu cm) similar to Phenolic Impregnated Carbon Ablator (PICA) or Silicone Impregnated Refractory Ceramic Ablator (SIRCA) and are comprised of: A flexible carbon substrate (Carbon felt) infiltrated with an ablative resin system: phenolic (Conformal-PICA) or silicone (Conformal-SICA). The test demonstrated a successful performance of both the conformable ablators for heat flux conditions between 50-500 W/sq cm. The recession and temperature profile for these materials were comparable to PICA proving them to be viable alternatives for TPS technology development for future missions.

Gasch, Matthew↗

NASA NTRSDate not supplied

A Separation Control CFD Validation Test Case: Baseline and Steady Suction - Part 1

Low speed flow separation over a wall-mounted hump, and its control using steady suction, were studied experimentally in order to generate a data set for a workshop aimed at validating CFD turbulence models. The baseline and controlled data sets comprised static and dynamic surface pressure measurements, flow field measurements using Particle Image Velocimetry (PIV) and wall shear stress obtained via oil-film interferometry. In addition to the specific test cases studied, surface pressures for a wide variety of conditions were reported for different Reynolds numbers and suction rates. Stereoscopic PIV and oil-film flow visualization indicated that the baseline separated flow field was mainly two- dimensional. With the application of control, some three-dimensionality was evident in the spanwise variation of pressure recovery, reattachment location and spanwise pressure fluctuations. Part 2 of this paper, under preparation for the AIAA Meeting in Reno 2005, considers separation control by means of zero-efflux oscillatory blowing.

David Greenblatt↗

NASA NTRS2004

A Separation Control CFD Validation Test Case: Baseline and Steady Suction - Part 1

Low speed flow separation over a wall-mounted hump, and its control using steady suction, were studied experimentally in order to generate a data set for a workshop aimed at validating CFD turbulence models. The baseline and controlled data sets comprised static and dynamic surface pressure measurements, flow field measurements using Particle Image Velocimetry (PIV) and wall shear stress obtained via oil-film interferometry. In addition to the specific test cases studied, surface pressures for a wide variety of conditions were reported for different Reynolds numbers and suction rates. Stereoscopic PIV and oil-film flow visualization indicated that the baseline separated flow field was mainly two-dimensional. With the application of control, some three-dimensionality was evident in the spanwise variation of pressure recovery, reattachment location and spanwise pressure fluctuations. Part 2 of this paper, under preparation for the AIAA Meeting in Reno 2005, considers separation control by means of zero-efflux oscillatory blowing.

Greenblatt, David↗

DOE OSTI2022

Effects of a composite flame retardant system on the flame retardancy and mechanical performance of epoxy resin adhesive

Abstract A flame‐retarded epoxy resin (ER) adhesive with strong flame retardancy and adhesion performance was prepared. The coated ammonium polyphosphate (MFAPP), melamine (MEL), and organic montmorillonite (OMMT) were mixed to prepare a composite flame retardant. It was subsequently blended with a toughened ER thoroughly and then the mixture was cured with polyamide. The resultant ER adhesive thermosets achieved UL‐94 V‐0 rating during vertical burning test, and the limiting oxygen index value was as high as 31.6%. The shear strength of the ER adhesive was 27.9 MPa when 25 wt% MFAPP/MEL/OMMT was introduced. Compared with the pure adhesive, the flame retardant epoxy adhesive maintained outstanding adhesion performance because of the good compatibility between the composite flame retardant additives and the toughened ER adhesive. Cone calorimetry tests indicated that the release of heat and smoke were obviously declined with the incorporation of the composite flame retardant system in comparison to pure ER adhesive thermoset. The investigation of flame retardant mechanism revealed that the composite MFAPP/MEL/OMMT flame retardant system stimulated the generation of highly expanded, integral, and strong char layer and the formed char layer exerted superior insulation effect during combusiton. The present work provided an alternative approach to prepare flame retardant ER adhesive with the similar excellent adhesive performance.

Li, Sheng↗

DOE OSTI2015

Adhesive interactions of geckos with wet and dry fluoropolymer substrates

Fluorinated substrates like Teflon® (poly(tetrafluoroethylene); PTFE) are well known for their role in creating non-stick surfaces. Previously, we showed that even geckos, which can stick to most surfaces under a wide variety of conditions, slip on PTFE. Surprisingly, however, geckos can stick reasonably well to PTFE if it is wet. In an effort to explain this effect, we have turned our attention to the role of substrate surface energy and roughness when shear adhesion occurs in media other than air. In this study, we removed the roughness component inherent to commercially available PTFE and tested geckos on relatively smooth wet and dry fluoropolymer substrates. We found that roughness had very little effect on shear adhesion in air or in water and that the level of fluorination was most important for shear adhesion, particularly in air. Surface energy calculations of the two fluorinated substrates and one control substrate using the Tabor–Winterton approximation and the Young–Dupré equation were used to determine the interfacial energy of the substrates. Using these interfacial energies we estimated the ratio of wet and dry normal adhesion for geckos clinging to the three substrates. Consistent with the results for rough PTFE, our predictions show a qualitative trend in shear adhesion based on fluorination, and the quantitative experimental differences highlight the unusually low shear adhesion of geckos on dry smooth fluorinated substrates, which is not captured by surface energy calculations. Our work has implications for bioinspired design of synthetics that can preferentially stick in water but not in air.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Utah FORGE 5-2428: Coupled Investigation of Fracture Permeability Impact on Reservoir Stress and Seismic Slip - 2024 Annual Workshop Presentation

This is a presentation on the Coupled Investigation of Fracture Permeability Impact on Reservoir Stress and Seismic Slip Behavior by Lawrence Livermore National Laboratory, presented by Kayla Kroll. This presentation addresses testing and modelling related to the dependency of EGS production on sustained permeability and sufficient fluid flow through pre-existing or induced fractures in hot rock. This presentation was featured in the Utah FORGE R&D Annual Workshop on August 13, 2024.

15 GEOTHERMAL ENERGY↗