Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “refinement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Crystal structure, homogeneity range and electronic structure of rhombohedral γ-Mn 5 Al 8

Here, the γ-region of the Mn–Al phase diagram between 45 and 70 at.% Al was re-investigated by a combination of powder and single crystal X-ray diffraction as well as EDS analysis to establish the distribution of Mn and Al atoms. Single crystals of γ-Mn 5–x Al 8+x were grown using Sn-flux at 650 °C. The crystal structure, atomic coordinates and site occupancy parameters of γ-Mn 5–x Al 8+x phases were refined from single crystal X-ray data. The γ-Mn 5-x Al 8+x phase adopts the rhombohedral Cr 5 Al 8 -type structure rather than a cubic γ-brass structure. The refined compositions from two crystals extracted from the Al-rich and Mn-rich sides are, respectively, Mn 4.76 Al 8.24(2) (I) and Mn 6.32 Al 6.68(2) (II). The structure was refined in the acentric R3m space group (No.160, Z=6), in order to compare with other reported rhombohedral γ-brasses. In addition, according to X-ray powder diffraction analysis, at the Al-rich side the γ-phase coexists with LT–Mn 4 Al 11 and, at the Mn-rich side, with a hitherto unknown phase. The refined lattice parameters from powder patterns fall in the range a=12.6814(7)–12.6012(5) Å and c=7.9444(2)–7.9311(2) Å from Al-rich to Mn-rich loadings, and the corresponding rhombohedral angles distorted from a pseudo-cubic cell were found to be 89.1(1)°–88.9(1)°. Magnetic susceptibility and magnetization studies of Mn 4.92 Al 8.08(2) are consistent with moment bearing Mn and suggest a spin glass state below 27 K. Tight-binding electronic structure calculations (LMTO-ASA with LSDA) showed that the calculated Fermi level for γ-“Mn 5 Al 8 ” falls within a pseudogap of the density of states, a result which is in accordance with a Hume-Rothery stabilization mechanism γ-brass type phases.

36 MATERIALS SCIENCE↗

Synchrotron Powder X-ray Diffraction Study of the Structure and Dehydration Behavior of Palygorskite

Rietveld refinements using synchrotron powder X-ray diffraction data were used to study the crystal structure and dehydration behavior of pure monoclinic palygorskite samples from Korea and Alaska. The 300 and 100 K palygorskite structures in air compare well with previous models but provide additional details about zeolitic H2O sites and reveal that the Al atoms are ordered into the inner M2 octahedral sites and the Mg cations into the M3 sites at the edges of the tunnels. Real-time, temperature-resolved synchrotron powder X-ray diffraction data and Rietveld refinements were used to investigate the monoclinic palygorskite structure from 300 to 1400 K (in air). Rietveld refinements showed that most of the zeolitic H2O is lost by 425 K, accompanied by a decrease in the unit-cell volume of 1.3%, primarily owing to a decrease in the a unit-cell parameter and an increase in the ? angle. The structurally bound H2O is lost in two stages, at temperature intervals of 475-540 and 580-725 K. Above 825 K in air a portion of the Korean sample transformed to a folded structure; the Alaskan sample folded at 575 K under vacuum. A structure model was refined for the folded structure. At 1015 K for the sample heated in air, ?-quartz diffraction peaks appeared and increased in intensity as heating continued to the maximum temperature. Cristobalite formed above 1050 K, along with a small amount of clinoenstatite, and both phases persisted to the maximum temperature studied.

36 MATERIALS SCIENCE↗

The structure of braitschite, a calcium rare earth borate

The crystal structure of braitschite, Ca6.15Na0.85RE2.08[B6O7(OH)3(O,OH)3]4(H2O), is reported here in space group P6/m with unit-cell parameters a = 12.1506(6), c = 7.3678(4) Å, and V = 942.03(8) Å3. Data were collected from a single crystal using a MoKα source and a CCD detector, solved by direct methods, and refined to an R factor of 2.81%. The mineral structure consists of hexaborate fundamental building blocks that polymerize along [001] and are bound by Ca2+ and REE3+ counter-ions. The framework forms hexagonal channels, which are occupied alternately by Ca2+ cations and water molecules. In an investigation of its thermal stability, braitschite maintains its crystallinity to a temperature of 400 °C, after which it undergoes decomposition. Using Rietveld refinements against powder X-ray diffraction data, we were able to track the loss of water molecules in channels and hydroxyl groups in the covalent B-O network with increasing temperature.

58 GEOSCIENCES↗

Hierarchy-Direction Selective Approach for Locally Adaptive Sparse Grids

We consider the problem of multidimensional adaptive hierarchical interpolation. We use sparse grids points and functions that are induced from a one dimensional hierarchical rule via tensor products. The classical locally adaptive sparse grid algorithm uses an isotropic refinement from the coarser to the denser levels of the hierarchy. However, the multidimensional hierarchy provides a more complex structure that allows for various anisotropic and hierarchy selective refinement techniques. We consider the more advanced refinement techniques and apply them to a number of simple test functions chosen to demonstrate the various advantages and disadvantages of each method. While there is no refinement scheme that is optimal for all functions, the fully adaptive family-direction-selective technique is usually more stable and requires fewer samples.

Stoyanov, Miroslav K↗

ORNL Evaluation of Electrabel Safety Cases for Doel 3 / Tihange 2: Final Report

Oak Ridge National Laboratory (ORNL) performed a detailed technical review of the 2015 Electrabel (EBL) Safety Cases prepared for the Belgium reactor pressure vessels (RPVs) at Doel 3 and Tihange 2 (D3/T2). The Federal Agency for Nuclear Control (FANC) in Belgium commissioned ORNL to provide a thorough assessment of the existing safety margins against cracking of the RPVs due to the presence of almost laminar flaws found in each RPV. Initial efforts focused on surveying relevant literature that provided necessary background knowledge on the issues related to the quasilaminar flaws observed in D3/T2 reactors. Next, ORNL proceeded to develop an independent quantitative assessment of the entire flaw population in the two Belgian reactors according to the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section XI, Appendix G, Fracture Toughness Criteria for Protection Against Failure, New York (1992 and 2004). That screening assessment of all EBL-characterized flaws in D3/T2 used ORNL tools, methodologies, and the ASME Code Case N-848, Alternative Characterization Rules for QuasiLaminar Flaws . Results and conclusions from the ORNL flaw acceptance assessments of D3/T2 were compared with those from the 2015 EBL Safety Cases. Specific findings of the ORNL evaluation of that part of the EBL structural integrity assessment focusing on stability of the flaw population subjected to primary design transients include the following: ORNL s analysis results were similar to those of EBL in that very few characterized flaws were found not compliant with the ASME (1992) acceptance criterion. ORNL s application of the more recent ASME Section XI (2004) produced only four noncompliant flaws, all due to LOCAs. The finding of a greater number of non-compliant flaws in the EBL screening assessment is due principally to a significantly more restrictive (conservative) criterion for flaw size acceptance used by EBL. ORNL s screening assessment results (obtained using an analysis methodology different from that of EBL) are interpreted herein as confirming the EBL screening results for D3/T2. ORNL s independent refined analysis demonstrated the EBL-characterized flaw 1660, which is non-compliant in the ORNL and EBL screening assessment, is rendered compliant when modeled as a more realistic individual quasi-laminar flaw using a 3-D XFEM analysis approach. ORNL s and EBL s refined analyses are in good agreement for the flaw 1660 close to the clad/base metal interface; ORNL is not persuaded that repeating this exercise for more than one non-compliant flaw is necessary to accept the EBL conclusions derived from the aggregate of EBL refined analysis results. ORNL General Conclusions Regarding the Structural Integrity Assessment (SIA) Conducted by EBL for D3/T2 Based on comparative evaluations of ORNL and EBL SIA analyses and on consideration of other results, ORNL is in agreement with the general conclusions reported by Electrabel in their RPV D3/T2 Technical Summary Note of April 14, 2015: More than 99 percent of flaws in D3/T2 meet the defined screening criterion, rendering them benign with respect to initiation in the event of a design transient. Refined analyses of non-compliant flaws from the screening assessment indicate that only 11 of the 16196 detected flaws have a critical reference-temperature material index (designated RTNDT) that implies the possibility of the initiation of cleavage fracture at some future time. For those 11 2 flaws, the calculated margin in RTNDT (a measure of acceptable embrittlement relative to end-ofservice-life conditions) is significant, being greater than 80 C. Fatigue crack growth is not a concern in the flaw-acceptability analyses. Primary stress re-evaluation confirms that the collapse pressure is more than 1.5 times the design pressure in the presence of defects detected in D3/T2. Sufficient conservatisms are built into the input data and into the different steps of the SIA; in some cases, those conservatisms are quantified and imply that additional margins exist in the SIA. Taken as a whole, the foregoing results and conclusions confirm the structural integrity of Doel 3 and Tihange 2 under all design transients with ample margin in the presence of the 16196 detected flaws.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Preliminary Characterization and Mechanical Performance of Additively Manufactured HT9

Laser-blown powder deposition of HT9 was performed to evaluate the feasibility of using advanced manufacturing to fabricate creep strength enhanced ferritic steels. The as-printed materials were tensile tested at room temperature, 330°C, and 550°C to provide a baseline value for the strength levels. The as-fabricated strengths are then compared with wrought materials in the published literature. The strength parameters for the as-fabricated HT9 was found to be significantly higher than that of wrought HT9 without sacrifice in ductility. Two different heat treatment cycles, deemed ACO3 and FCRD, involving two different austentizing temperatures (1065°C and 1040°C) and tempering temperatures (750°C and 760°C) were then evaluated. The heat-treated samples were also tensile tested and were found to show strength and ductility parameters which closely mimicked that of the wrought HT9 literature data. Detailed multi-scale characterization was performed at various length scales. The as-fabricated structure showed a refined martensitic structure with a significant fraction of δ-ferrite present. Closer examination using TEM showed a refined distribution of carbides (predominantly M 23 C 6 and MX or M2X), which would have precipitated during the deposition process. Upon heat treatment, it was seen that the precipitates were more homogenous and refined in the case of the specimens heat treated according to the ACO 3 cycle although there was no significant difference in the strength or the hardness results. However, the specimens heat-treated per the FCRD cycle showed significantly smaller prior austenite grains (measure and give quantitative numbers), which could result in better Charpy toughness. However, the toughness was not evaluated and will be performed in the future. In addition, possible thermos-mechanical treatments (TMT) to refine the grain structure and improve the toughness without compromising the ductility will also be evaluated in the future.

36 MATERIALS SCIENCE↗

The arbitrary-order virtual element method for linear elastodynamics models. Convergence, stability and dispersion-dissipation analysis.

We design the conforming virtual element method for the numerical approximation of the two dimensional elastodynamics problem. We prove stability and convergence of the semi-discrete approximation and derive optimal error estimates under $\textit{h}$-refinement in both the energy and the $L^2$ norms, and optimal error estimates under $\textit{p}$-refinement in the energy norm. The performance of the proposed virtual element method is assessed on a set of different computational meshes, including non-convex cells up to order four in the h-refinement setting. Exponential convergence is also experimentally observed under p-refinement. Finally, we present a dispersion-dissipation analysis for both the semi-discrete and fully-discrete schemes, showing that polygonal meshes behave as classical simplicial/quadrilateral grids in terms of dispersion-dissipation properties.

97 MATHEMATICS AND COMPUTING↗

Enabling Real-time Scattering Data Analysis with Scalable Optimization [Slides]

Diffraction experiments produce datasets with rich multidimensional physics information such as microstructure, equations of state, crystal structure, elastoplastic properties, and other key inputs to LANL mission-essential multiphysics models. This information is typically extracted through a process called Rietveld refinement, which involves selecting appropriate models of the instrument, crystal structure, and microstructure, identifying suitable starting values, and then fitting often hundreds of model parameters using a sequence of empirical parameter turnon/off sequences within a non-global gradient-based optimization. Extensive user expertise is required to properly setup a refinement, identify appropriate models, and select initial parameter values close to truth, such that the refinement will yield parameter values that are optimally predictive. This is a very tedious manual process performed far after the beamline campaign has ended. As facilities have become capable of generating larger volumes of data, the limitation in throughput due to Rietveld refinement has led to a dramatic increase in unanalyzed data as opposed to an intended increase in new science. In our FY22 TED, we demonstrated an integrated toolset providing near real-time automated Rietveld analysis. If this toolset can be optimized to provide automated Rietveld analysis in real-time, this could alleviate the bottleneck in unanalyzed diffraction data, aid in decision-making during experiments, and increase efficiency of the facility.

74 ATOMIC AND MOLECULAR PHYSICS↗

Preserving Superconvergence of Spectral Elements for Curved Domains

Spectral element methods (SEM), extensions of finite element methods (FEM), have emerged as significant techniques for solving partial differential equations in physics and engineering. SEM can potentially deliver superior accuracy due to the potential superconvergence in nodal solutions for well-shaped tensor-product elements. However, the accuracy of SEM often degrades in complex geometries due to geometric inaccuracies near curved boundaries and the loss of superconvergence with simplicial or non-tensor-product elements. To overcome the first issue, we propose using geometric refinement, which both refines the mesh near high-curvature regions and increases the degree of geometric basis functions. We show that when using mixed-element meshes with tensor-product elements in the interior of the domain, curvature-based geometric refinement near boundaries can improve the accuracy of the interior elements by reducing pollution errors and preserving the superconvergence in nodal solutions. To address the second issue, we introduce ApSEM, a post-processing technique using the adaptive extended stencil finite element method (AES-FEM) to recover the accuracy near the curved boundaries. The combination of curvature-based geometric refinement and accurate post-processing offers an effective and easier-to-implement alternative to methods reliant on exact geometries. We demonstrate our techniques by solving the convection-diffusion equation in 2D and 3D and show up to two orders of magnitude of improvement in the solution accuracy, even when the elements are poorly shaped near boundaries. We also show the efficiency of ApSEM as it can recover superconvergence in nodal solutions without drastically increasing the computational cost.

97 MATHEMATICS AND COMPUTING↗

Southwest Regional Partnership on Carbon Sequestration: Phase III (Final Scientific/Technical Report)

The Southwest Regional Partnership on Carbon Sequestration (SWP) is one of 7 regional partnerships formed in 2003 under the U.S. Department of Energy’s (DOE) Regional Carbon Sequestration Partnerships (RCSPs) initiative. The overall purpose of the initiative was to help determine and implement the technology, infrastructure, and regulations most appropriate to promote carbon storage in different regions of the country. Covering Arizona, Colorado, New Mexico, Oklahoma, Utah, and parts of Texas, Wyoming, and Kansas, the SWP evaluated regional carbon storage and utilization potential and focused on technologies and sites that could complement the region’s strong position in energy production. The project progressed through three phases: • Phase I (2003–2005): Characterized regional geologic formations and CO 2 sources, assessed sequestration potential, and identified pilot test sites. • Phase II (2005–2013): Conducted small-scale field tests to validate sequestration methods, including geologic and terrestrial projects. • Phase III (2008–2022): Demonstrated large-scale CO 2 injection at a commercial oil field to test monitoring, verification, and long-term storage strategies. This report covers Phase III. The final project site, the Farnsworth Unit (FWU) in Texas, provided real-world testing of reservoir characterization, monitoring, and risk evaluation tools and processes that could be used in any commercial scale carbon capture, utilization, and storage (CCUS) project. Extensive data collection and analysis helped refine best practices for reservoir characterization, injection monitoring, and storage verification. The SWP contributed to national databases, DOE best practice manuals, and regional geological assessments to support future sequestration efforts. Key lessons learned include the importance of robust data management, strategic site selection, regulatory navigation, and effective industry collaboration. The project’s findings will inform ongoing and future carbon storage initiatives. Task 1 (Regional Characterization) • The SWP continued to participate in national outreach efforts and NATCARB. • The SWP evaluated multiple potential sites before selecting the FWU as the primary field test location. Task 2 (Public Outreach and Education) • The SWP contributed to national databases, DOE best practice manuals, and regional geological assessments to support future sequestration efforts. Task 3 (Permitting and Regulatory Compliance) • The SWP ensured compliance with federal and state regulations, including National Environmental Policy Act (NEPA) requirements. • The SWP obtained all necessary permits for drilling, injection, and monitoring activities. Task 4 (Site Characterization and Planning) • The SWP developed work plans for four key activities: characterization, simulation, monitoring and verification, and risk evaluation. • The SWP collected and synthesized legacy data from multiple sources to build initial static geological models and dynamic reservoir models demonstrating project feasibility. • The SWP conducted an initial risk evaluation and developed mitigation plans. Task 5 (Field Operations and Data Collection) • The SWP drilled, logged, and cored three characterization wells to gather critical subsurface data. • The SWP conducted multiple geophysical surveys, including 3D seismic, crosswell seismic, and vertical seismic profiling, to improve reservoir characterization. Task 6 (Monitoring and Verification) • The SWP performed extensive geological characterization using data from characterization wells and seismic surveys. • The SWP established a surface monitoring network to track CO 2 flux in soil gas, groundwater chemistry, and near-surface atmospheric CO 2 levels. • The SWP built and refined reservoir models to study the effects of relative permeability on simulation behavior and improve calibration with experimental data. Task 7 (Risk Assessment and Model Refinement) • The SWP conducted multiple studies to evaluate reservoir integrity, predict CO 2 plume behavior and improve predictive modeling capabilities. • The SWP refined geological models and used them to enhance the accuracy of simulation models. • The SWP continued quantitative risk assessment of top-ranked risks and strengthened the link between qualitative and quantitative risk methodologies.

02 PETROLEUM↗

Overview of the design, construction, and operation of interstate liquid petroleum pipelines.

The U.S. liquid petroleum pipeline industry is large, diverse, and vital to the nation's economy. Comprised of approximately 200,000 miles of pipe in all fifty states, liquid petroleum pipelines carried more than 40 million barrels per day, or 4 trillion barrel-miles, of crude oil and refined products during 2001. That represents about 17% of all freight transported in the United States, yet the cost of doing so amounted to only 2% of the nation's freight bill. Approximately 66% of domestic petroleum transport (by ton-mile) occurs by pipeline, with marine movements accounting for 28% and rail and truck transport making up the balance. In 2004, the movement of crude petroleum by domestic federally regulated pipelines amounted to 599.6 billion tonmiles, while that of petroleum products amounted to 315.9 billion ton-miles (AOPL 2006). As an illustration of the low cost of pipeline transportation, the cost to move a barrel of gasoline from Houston, Texas, to New York Harbor is only 3 cents per gallon, which is a small fraction of the cost of gasoline to consumers. Pipelines may be small or large, up to 48 inches in diameter. Nearly all of the mainline pipe is buried, but other pipeline components such as pump stations are above ground. Some lines are as short as a mile, while others may extend 1,000 miles or more. Some are very simple, connecting a single source to a single destination, while others are very complex, having many sources, destinations, and interconnections. Many pipelines cross one or more state boundaries (interstate), while some are located within a single state (intrastate), and still others operate on the Outer Continental Shelf and may or may not extend into one or more states. U.S. pipelines are located in coastal plains, deserts, Arctic tundra, mountains, and more than a mile beneath the water's surface of the Gulf of Mexico (Rabinow 2004; AOPL 2006). The network of crude oil pipelines in the United States is extensive. There are approximately 55,000 miles of crude oil trunk lines (usually 8 to 24 inches in diameter) in the United States that connect regional markets. The United States also has an estimated 30,000 to 40,000 miles of small gathering lines (usually 2 to 6 inches in diameter) located primarily in Texas, Oklahoma, Louisiana, and Wyoming, with small systems in a number of other oil producing states. These small lines gather the oil from many wells, both onshore and offshore, and connect to larger trunk lines measuring 8 to 24 inches in diameter. There are approximately 95,000 miles of refined products pipelines nationwide. Refined products pipelines are found in almost every state in the United States, with the exception of some New England states. These refined product pipelines vary in size from relatively small, 8- to 12-inch-diameter lines, to up to 42 inches in diameter. The overview of pipeline design, installation, and operation provided in the following sections is only a cursory treatment. Readers interested in more detailed discussions are invited to consult the myriad engineering publications available that provide such details. The two primary publications on which the following discussions are based are: Oil and Gas Pipeline Fundamentals (Kennedy 1993) and the Pipeline Rules of Thumb Handbook (McAllister 2002). Both are recommended references for additional reading for those requiring additional details. Websites maintained by various pipeline operators also can provide much useful information, as well as links to other sources of information. In particular, the website maintained by the U.S. Department of Energy's Energy Information Administration (EIA) (http://www.eia.doe.gov) is recommended. An excellent bibliography on pipeline standards and practices, including special considerations for pipelines in Arctic climates, has been published jointly by librarians for the Alyeska Pipeline Service Company (operators of the Trans-Alaska Pipeline System [TAPS]) and the Geophysical Institute/International Arctic Research Center, both located in Fairbanks (Barboza and Trebelhorn 2001), available electronically at http://www.gi.alaska.edu/services/library/pipeline.html codes. The Association of Oil Pipe Lines (AOPL) and the American Petroleum Institute (API) jointly provide an overview covering the life cycle of design, construction, operations, maintenance, economic regulation, and deactivation of liquid pipelines (AOPL/API 2007).

02 PETROLEUM↗

Effect of Cooling Rate on Nano-Eutectic Formation in Laser Surface Remelted and Rare Earth Modified Hypereutectic Al-20Si Alloys

Laser Surface Remelting (LSR) was applied to arc-melted Al-20Si-0.2Sr, Al-20Si-0.2Ce, and Al-20Si hypereutectic alloys to refine microstructures. Experiments revealed that microstructures in the melt pool varied from fully eutectic to a mixture of Al dendrites and inter-dendritic eutectic. We calculated cooling rates using the Eagar-Tsai model and correlated cooling rates with characteristic microstructures, revealing that a cooling rate on the order of 104 K/s could lead to maximized fully eutectic microstructure morphology. Due to rapid solidification, the Si composition in the LSR eutectic was measured at 18.2 wt.%, higher than the equilibrium eutectic composition of 12.6 wt.%Si. Compared to Al-20Si, Ce addition had no significant effect on the volume fraction of the fully eutectic structure but refined Si fibers to approximately 30 nm in diameter. Sr addition did not further refine the diameter of eutectic Si fibers compared to Al-20Si but increased the volume fraction of the fully eutectic microstructure morphology. The refinement ratio (φ) of the Si fiber diameter from the bottom of the melt pool to the surface for the three alloys was similar, at around 28%. The established correlation between the cooling rate and the size and morphology of the microstructure within the melt pool will enable tailoring of the microstructure in laser-processed as well as deposited alloys for high strength and plasticity.

36 MATERIALS SCIENCE↗

New insights into the drainage of inundated ice-wedge polygons using fundamental hydrologic principles

Abstract. The pathways and timing of drainage from the inundated centers of ice-wedge polygons in a warming climate have important implications for carbon flushing, advective heat transport, and transitions from methane to carbon dioxide dominated emissions. Here, we expand on previous research using a recently developed analytical model of drainage from a low-centered polygon. Specifically, we perform (1) a calibration to field data identifying necessary model refinements and (2) a rigorous model sensitivity analysis that expands on previously published indications of polygon drainage characteristics. This research provides intuition on inundated polygon drainage by presenting the first in-depth analysis of drainage within a polygon based on hydrogeological first principles. We verify a recently developed analytical solution of polygon drainage through a calibration to a season of field measurements. Due to the parsimony of the model, providing the potential that it could fail, we identify the minimum necessary refinements that allow the model to match water levels measured in a low-centered polygon. We find that (1) the measured precipitation must be increased by a factor of around 2.2, and (2) the vertical soil hydraulic conductivity must decrease with increasing thaw depth. Model refinement (1) accounts for runoff from rims into the ice-wedge polygon pond during precipitation events and possible rain gauge undercatch, while refinement (2) accounts for the decreasing permeability of deeper soil layers. The calibration to field measurements supports the validity of the model, indicating that it is able to represent ice-wedge polygon drainage dynamics. We then use the analytical solution in non-dimensional form to provide a baseline for the effects of polygon aspect ratios (radius to thaw depth) and coefficient of hydraulic conductivity anisotropy (horizontal to vertical hydraulic conductivity) on drainage pathways and temporal depletion of ponded water from inundated ice-wedge polygon centers. By varying the polygon aspect ratio, we evaluate the relative effect of polygon size (width), inter-annual increases in active-layer thickness, and seasonal increases in thaw depth on drainage. The results of our sensitivity analysis rigorously confirm a previous analysis indicating that most drainage through the active layer occurs along an annular region of the polygon center near the rims. This has important implications for transport of nutrients (such as dissolved organic carbon) and advection of heat towards ice-wedge tops. We also provide a comprehensive investigation of the effect of polygon aspect ratio and anisotropy on drainage timing and patterns, expanding on previously published research. Our results indicate that polygons with large aspect ratios and high anisotropy will have the most distributed drainage, while polygons with large aspect ratios and low anisotropy will have their drainage most focused near their periphery and will drain most slowly. Polygons with small aspect ratios and high anisotropy will drain most quickly. These results, based on parametric investigation of idealized scenarios, provide a baseline for further research considering the geometric and hydraulic complexities of ice-wedge polygons.

Harp, Dylan R. (ORCID:0000000197778000)↗

Superstructure and stacking faults in hydrothermal-grown KBe{sub 2}BO{sub 3}F{sub 2} crystals

The structure of the hydrothermal-grown nonlinear optical crystal KBe{sub 2}BO{sub 3}F{sub 2} was investigated. A new structure of the R3-bar c space group with cell parameters of a=4.422(1) A and c=37.524(3) A was obtained by powder X-ray diffraction and Rietveld refinement. The new structure is a 1x1x2 superstructure of the previously reported R32 structure with a different stacking sequence of (Be{sub 2}BO{sub 3}F{sub 2}){sub {infinity}} layers along the c axis. The relationship between the refined structure and the experimental results is discussed. A stacking fault mechanism is proposed for the formation of the superstructure as well as the nonuniformity of the hydrothermal-grown KBBF crystals. - Graphical Abstract: A new structure of the R3-bar c space group with cell parameters of a=4.422(1) A and c=37.524(3) A was obtained from hydrothermal-grown KBe{sub 2}BO{sub 3}F{sub 2} crystals by powder XRD and Rietveld refinement. Highlights: > Structural investigation on hydrothermal-grown KBe{sub 2}BO{sub 3}F{sub 2} crystals by powder XRD and Rietveld refinement. > Relationship between structures and SHG properties. > Superstructure formed by stacking faults during hydrothermal crystal growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A combined fit of total scattering and extended x-ray absorption fine structure data for local-structure determination in crystalline materials

Reverse Monte Carlo (RMC) refinements of local structure using a simultaneous fit of X-ray/neutron total scattering and extended X-ray absorption fine structure (EXAFS) data were developed to incorporate an explicit treatment of both single- and multiple-scattering contributions to EXAFS. The refinement algorithm, implemented as an extension to the public domain computer software RMCProfile, enables accurate modeling of EXAFS over distances encompassing several coordination shells around the absorbing species. The approach was first tested on Ni, which exhibits extensive multiple scattering in EXAFS, and then applied to perovskite-like SrAl{sub 1/2}Nb{sub 1/2}O{sub 3}. This compound crystal1izes with a cubic double-perovskite structure but presents a challenge for local-structure determination using a total pair-distribution function (PDF) alone because of overlapping peaks of the constituent partial PDFs (e.g. Al-O and Nb-O or Sr-O and O-O). The results obtained here suggest that the combined use of the total scattering and EXAFS data provides sufficient constraints for RMC refinements to recover fine details of local structure in complex perovskites. Among other results, it was found that the probability density distribution for Sr in SrAl{sub 1/2}Nb{sub 1/2}O{sub 3} adopts T{sub d} point-group symmetry for the Sr sites, determined by the ordered arrangement of Al and Nb, as opposed to a spherical distribution commonly assumed in traditional Rietveld refinements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Unstructured discontinuous Galerkin for seismic inversion.

This abstract explores the potential advantages of discontinuous Galerkin (DG) methods for the time-domain inversion of media parameters within the earth's interior. In particular, DG methods enable local polynomial refinement to better capture localized geological features within an area of interest while also allowing the use of unstructured meshes that can accurately capture discontinuous material interfaces. This abstract describes our initial findings when using DG methods combined with Runge-Kutta time integration and adjoint-based optimization algorithms for full-waveform inversion. Our initial results suggest that DG methods allow great flexibility in matching the media characteristics (faults, ocean bottom and salt structures) while also providing higher fidelity representations in target regions. Time-domain inversion using discontinuous Galerkin on unstructured meshes and with local polynomial refinement is shown to better capture localized geological features and accurately capture discontinuous-material interfaces. These approaches provide the ability to surgically refine representations in order to improve predicted models for specific geological features. Our future work will entail automated extensions to directly incorporate local refinement and adaptive unstructured meshes within the inversion process.

58 GEOSCIENCES↗

Introducing Enabling Computational Tools to the Climate Sciences: Multi-Resolution Climate Modeling with Adaptive Cubed-Sphere Grids

The research investigates and advances strategies how to bridge the scale discrepancies between local, regional and global phenomena in climate models without the prohibitive computational costs of global cloud-resolving simulations. In particular, the research explores new frontiers in computational geoscience by introducing high-order Adaptive Mesh Refinement (AMR) techniques into climate research. AMR and statically-adapted variable-resolution approaches represent an emerging trend for atmospheric models and are likely to become the new norm in future-generation weather and climate models. The research advances the understanding of multi-scale interactions in the climate system and showcases a pathway how to model these interactions effectively with advanced computational tools, like the Chombo AMR library developed at the Lawrence Berkeley National Laboratory. The research is interdisciplinary and combines applied mathematics, scientific computing and the atmospheric sciences. In this research project, a hierarchy of high-order atmospheric models on cubed-sphere computational grids have been developed that serve as an algorithmic prototype for the finite-volume solution-adaptive Chombo-AMR approach. The foci of the investigations have lied on the characteristics of both static mesh adaptations and dynamically-adaptive grids that can capture flow fields of interest like tropical cyclones. Six research themes have been chosen. These are (1) the introduction of adaptive mesh refinement techniques into the climate sciences, (2) advanced algorithms for nonhydrostatic atmospheric dynamical cores, (3) an assessment of the interplay between resolved-scale dynamical motions and subgrid-scale physical parameterizations, (4) evaluation techniques for atmospheric model hierarchies, (5) the comparison of AMR refinement strategies and (6) tropical cyclone studies with a focus on multi-scale interactions and variable-resolution modeling. The results of this research project demonstrate significant advances in all six research areas. The major conclusions are that statically-adaptive variable-resolution modeling is currently becoming mature in the climate sciences, and that AMR holds outstanding promise for future-generation weather and climate models on high-performance computing architectures.

58 GEOSCIENCES↗

Development of Solar Grade (SoG) Silicon

The rapid growth of the photovoltaics (PV) industry is threatened by the ongoing shortage of suitable solar grade (SoG) silicon. Until 2004, the PV industry relied on the off spec polysilicon from the electronics industry for feedstock. The rapid growth of PV meant that the demand for SoG silicon predictably surpassed this supply. The long-term prospects for PV are very bright as costs have come down, and efficiencies and economies of scale make PV generated electricity ever more competitive with grid electricity. However, the scalability of the current process for producing poly silicon again threatens the future. A less costly, higher volume production technique is needed to supply the long-term growth of the PV industry, and to reduce costs of PV even further. This long-term need was the motivation behind this SBIR proposal. Upgrading metallurgical grade (MG) silicon would fulfill the need for a low-cost, large-scale production. Past attempts to upgrade MG silicon have foundered/failed/had trouble reducing the low segregation coefficient elements, B, P, and Al. Most other elements in MG silicon can be purified very efficiently by directional solidification. Thus, in the Phase I program, Crystal Systems proposed a variety of techniques to reduce B, P, and Al in MG silicon to produce a low cost commercial technique for upgrading MG silicon. Of the variety of techniques tried, vacuum refining and some slagging and additions turned out to be the most promising. These were pursued in the Phase II study. By vacuum refining, the P was reduced from 14 to 0.22 ppmw and the Al was reduced from 370 ppmw to 0.065 ppmw. This process was scaled to 40 kg scale charges, and the results were expressed in terms of half-life, or time to reduce the impurity concentration in half. Best half-lives were 2 hours, typical were 4 hours. Scaling factors were developed to allow prediction of these results to larger scale melts. The vacuum refining required the development of new crucibles, as well as liners and coatings to allow the vacuum to be achieved. These developments also hold the promise of lower cost ingot growth, because several of these developments led to a reusable crucible. Liners and coatings were tested on 37 runs, under a variety of conditions. Although many of these did not fulfill the requirements of the program, several were very successful, particularly in allowing the crucible to be reused several times. The most interesting result was with slags and additives used to reduce P and Al. Although slags have been much studied with little success in removing P and B effectively, certain modeling suggested a particular type of slagging might be effective. This was tried, and found to be highly effective for P and surprisingly effective for B, as well. The best results indicate that > 99% of the P was removed, and > 75% of the B was removed by a slagging treatment. An operability issue involving separation of the slag and silicon was the final technical problem preventing the full-scale use of this technique, and there has been progress on this front. A slagging/additive technique is highly promising, because the rates of equilibration are very high, and this is a rapid technique that scales very well to large volumes with little increase in time. Materials of containment and slag/metal separation are issues that are continuing to be developed.

14 SOLAR ENERGY↗