Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Ceramic Paste for Patching High-Temperature Insulation

A ceramic paste that can be applied relatively easily, either by itself or in combination with one or more layer(s) of high-temperature ceramic fabrics, such as silicon carbide or zirconia, has been invented as a means of patching cracks or holes in the reinforced carbon-carbon forward surfaces of a space shuttle in orbit before returning to Earth. The paste or the paste/fabric combination could also be used to repair rocket-motor combustion chambers, and could be used on Earth to patch similar high-temperature structures. The specified chemical composition of the paste admits of a number of variations, and the exact proportions of its constituents are proprietary. In general, the paste consists of (1) silicon carbide, possibly with addition of (2) hafnium carbide, zirconium carbide, zirconium boride, silicon tetraboride, silicon hexaboride, or other metal carbides or oxides blended with (3) a silazane-based polymer. Because the paste is viscous and sticky at normal terrestrial and outer-space ambient temperatures, high-temperature ceramic fabrics such as silicon carbide or zirconia fabric impregnated with the paste (or the paste alone) sticks to the damaged surface to which it is applied. Once the patch has been applied, it is smoothed to minimize edge steps as required [forward-facing edge steps must be < or equal to 0.030 in. (< or equal to 0.76 mm) in the original intended space-shuttle application]. The patch is then heated to a curing temperature thereby converting it from a flexible material to a hard, tough material. The curing temperature is 375 to 450 F (approx.190 to 230 C). In torch tests and arc-jet tests, the cured paste was found to be capable of withstanding a temperature of 3,500 F (approx. 1,900 C) for 15 minutes. As such, the material appears to satisfy the requirement, in the original space-shuttle application, to withstand re-entry temperatures of approx.3,000 F (approx. 1,600 C).

Adam, Steven J.↗
NASA NTRS2004

Improved Thermoplastic/Iron-Particle Transformer Cores

A method of fabricating improved transformer cores from composites of thermoplastic matrices and iron-particles has been invented. Relative to commercially available laminated-iron-alloy transformer cores, the cores fabricated by this method weigh less and are less expensive. Relative to prior polymer-matrix/ iron-particle composite-material transformer cores, the cores fabricated by this method can be made mechanically stronger and more magnetically permeable. In addition, whereas some prior cores have exhibited significant eddy-current losses, the cores fabricated by this method exhibit very small eddy-current losses. The cores made by this method can be expected to be attractive for use in diverse applications, including high-signal-to-noise transformers, stepping motors, and high-frequency ignition coils. The present method is a product of an experimental study of the relationships among fabrication conditions, final densities of iron particles, and mechanical and electromagnetic properties of fabricated cores. Among the fabrication conditions investigated were molding pressures (83, 104, and 131 MPa), and molding temperatures (250, 300, and 350 C). Each block of core material was made by uniaxial-compression molding, at the applicable pressure/temperature combination, of a mixture of 2 weight percent of LaRC (or equivalent high-temperature soluble thermoplastic adhesive) with 98 weight percent of approximately spherical iron particles having diameters in the micron range. Each molded block was cut into square cross-section rods that were used as core specimens in mechanical and electromagnetic tests. Some of the core specimens were annealed at 900 C and cooled slowly before testing. For comparison, a low-carbon-steel core was also tested. The results of the tests showed that density, hardness, and rupture strength generally increased with molding pressure and temperature, though the correlation was rather weak. The weakness of the correlation was attributed to the pores in the specimens. The maximum relative permeabilities of cores made without annealing ranged from 30 to 110, while those of cores made with annealing ranged from 900 to 1,400. However, the greater permeabilities of the annealed specimens were not associated with noticeably greater densities. The major practical result of the investigation was the discovery of an optimum distribution of iron-particle sizes: It was found that eddy-current losses in the molded cores were minimized by using 100 mesh (corresponding to particles with diameters less than or equal to 100 m) iron particles. The effect of optimization of particle sizes on eddy-current losses is depicted in the figure.

Wincheski, Russell A.↗
DOE OSTI2024

Energy Efficiency Improvement Approaches in Ice Related Processes

Application and development of energy efficient techniques to separate ice from different surfaces and substrates is of significant value in the context of building equipment performance. A hybrid approach to help dislocate the ice layer using advanced materials and ultrasonic vibration to lower ice adhesion strength was investigated. Application of advanced polymer materials in lowering the adhesion strength of ice was confirmed where the measured strength was lowered by 50-70% depending on the material and geometry. Additionally, utilization of induced ultrasonic vibration in further lowering the ice harvesting energy was confirmed on multiple materials and geometries. Durability of the coating enhancement was also confirmed in a thermal cycling test under realistic operating conditions. Integration of these technical approaches was implemented and validated in commercial ice makers showing energy consumption reduction by ~ 15% to 30% depending on the technical enhancement.

Cheekatamarla, Praveen↗
DOE OSTI2020

Structural Dynamics in UV Curable Resins Resolved by In Situ 3D Printing X-ray Photon Correlation Spectroscopy

Additive manufacturing (AM) is a promising technique to rapidly produce polymeric materials into complex 3-dimensional (3D) geometries. While AM is widespread and relevant for a range of applications, implementation in industry has outpaced our fundamental understanding of polymer dynamics and structure development during the printing process. Characterization and quantification of such dynamics is necessary to optimize final material properties and design future materials and processes for 3D printing. Here, we utilize X-ray photon correlation spectroscopy (XPCS) to measure spatial and time-resolved, out-of-equilibrium dynamics during direct ink write (DIW) 3D printing. Specifically, we investigate the progression of structural dynamics in a dual cure (UV/thermal) nanocomposite during and directly after printing. As the filament is printed and cured in situ, the relaxation processes of the cross-linking network are measured through the dynamics of inorganic filler particles. The characteristic relaxation time of the dynamics is calculated through the intensity–intensity autocorrelation function g 2 and directly correlated to the printing process parameters, such as printhead velocity and UV light intensity. The time-resolved evolution of nanoscale dynamics follows a power-law dependence as the filament is cured. Additionally, bulk rheological characterizations reveal the macroscopic solidification of the resin, providing correlation of material properties across a wide range of length and time scales. Overall, the measurement of multiscale, out-of-equilibrium dynamics provides insight into the development of structure in polymer nanocomposite filaments during 3D printing and is used to further understand the influence of such parameters on the AM process.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Product specific thermal degradation kinetics of bisphenol F epoxy in inert and oxidative atmospheres using evolved gas analysis–mass spectrometry

Knowledge of the degradation kinetics for polymer materials is important for understanding thermal stability. In this study, evolved gas analysis–mass spectrometry and pyrolysis gas-chromatography-mass spectrometry were evaluated for the potential to deliver additional insight into thermal degradation kinetics of diglycidal ether of bisphenol F (DGEBF) epoxy thermoset under inert and oxidative atmospheres. Degradation products of selected precursor ions were evaluated for their uniqueness to the specific precursor using extracted ion thermographs. Unique mass peaks, solely attributed to a single reaction pathway of a specific product, were determined from extracted ion thermographs and used to determine both activation energy (E a ) and pre-exponential factors for the specific primary reaction pathways. These primary reaction pathways for DGEBF epoxy degradation were then evaluated in the context of transition state theory (TST) and related transition state enthalpies (ΔH ‡ ) and entropies (ΔS ‡ ) of activation to further elucidate the degradation process. It was determined under pyrolysis conditions, as suggested by the E a , the formation of bisphenol F monomer was the rate-limiting step toward the formation of xanthene and phenol. In contrast, under thermo-oxidative conditions, reactions involving oxygen containing species were identified as the rate-limiting step for all observed products based on the large negative ΔS ‡ calculated from TST. This work demonstrates a powerful combination of technique and theory that can provide new insight into the degradation of polymer materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Revealing Mesoscale Ionomer Membrane Structure by Tender Resonant X-ray Scattering

Nafion, a perfluorosulfonic acid ionomer, has been well-studied for decades due to its key role as an ion-conductive membrane in electrochemical energy conversion and storage applications. When hydrated, this membrane phase separates into a complex hierarchical nanostructure with hydrophilic domains that facilitate ion transport. Hard X-ray scattering has been a powerful technique in understanding Nafion due to its capabilities in capturing the ionomer’s nanophase separated structure, which gives rise to contrast between polymer and water domains. More recently, resonant X-ray scattering, which tunes to elemental absorption edges to provide specificity on constituent elements, has been explored to highlight key interactions related to the sulfonic acid groups within its structure. Here, in this work, we study the Nafion nanostructure by combining hard X-ray scattering and tender resonant X-ray scattering (TReXS) at the sulfur K-edge to reveal a mesoscopic feature corresponding to a correlation length of approximately 40 nm that has been challenging to resolve with hard X-ray studies. Additionally, we study the effect of the dispersion solvent composition that plays a key role in the formation of this mesoscale feature. Notably, TReXS can attain high contrast to decipher this mesoscale morphology even for dry polymer membranes under a vacuum, which typically have reduced contrast for hard X-rays. We find that the correlation length of this mesoscale feature decreases with increasing water fraction in the dispersion, which is the opposite trend exhibited by the smaller intercrystalline feature in the same membranes. This study showcases the utility of TReXS to uncover multiscale morphological details in functional polymers that are not always revealed by other methods like hard X-ray scattering. We illustrate this with Nafion, which is a relevant ion-conducting polymer for electrochemical technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Processing and 3D printing of SiCN polymer-derived ceramics

Preceramic polymer resins are attractive for the 3D printing of net-shaped ceramic components. Recently various processes have been demonstrated for 3D printing of polymer-derived ceramics (PDCs). Ultimately in these processes, the process outcomes strongly depend on the process parameters. In particular, for PDCs the ceramic density, and ceramic yield are affected by the catalyst concentration and cross-linking duration. Here, we use thermal analysis and FTIR to quantify the interrelation of the process parameters on the process outcome for polysilazanes and demonstrate 3D printing of PDC components based on the best-identified process parameters. Furthermore, the results of this work can be used as guidelines for future additive manufacturing of PDCs.

36 MATERIALS SCIENCE↗
NASA NTRS1974

The Acute Inhalation Toxicity in Rats from the Pyrolysis Products of Four Fluoropolymers

Male Sprague-Dawley rats (225?250 g) were exposed to the thermal degradation products from four fluoropolymers. The three polymers containing vinylidene fluoride and hexafluoropropene (VF2/HFP) were pyrolyzed at 550? and 800?C, whereas polytetrafluoroethylene (PTFE) was pyrolyzed at 625 and 800?C. At the lower temperatures, the pyrolysate from the copolymer of vinylidene fluoride and hexafluoropropene (VF2/HFP) was less toxic than the pyrolysates from either the terpolymer of vinyidene fluoride, hexafluoropropene, and tetrafluoroethylene (VF2/HFP/TFE) or the copolymer of vinylidene fluoride and hexafluoropropene with ?additives? (VF2/HFP-A). However, the pyrolysates from the VF2/HFP-containing materials produced less toxic products than the pyrolysate from PTFE at 625?C. When the pyrolysis temperature was increased to 800?C, very little difference was noted between the pyrolysis toxicity for any of the VF2/HFP-containing polymers with the most toxic pyrolysate again produced by PTFE. Carbon monoxide levels were all sublethal. No correlation could be established between hydrolyzable fluoride levels and the lethality of the pyrolysates. Death following exposure occurred within 48 hr due to acute pulmonary edema and hemorrhage. Survival of this acute phase was followed by alveolar lymphocytic infiltration and peribronchial tissue proliferation.

Carter, V. L., Jr.↗
DOE OSTI2021

Nanocomposites Based on Coil-Comb Diblock Copolymers

The polymer chain architecture is an important factor determining the phase behavior of nanoparticle (NP) assembly in polymer matrices. Block copolymers (BCPs) containing a random copolymer (RCP) block present a convenient variation on traditional BCPs to tune the interaction parameters between the polymer blocks and the nanofillers as well as to evaluate the effect of the chain architecture on the NP arrangements within BCP microdomains. Here, we synthesized BCPs with a coil polystyrene (PS) block and a comb RCP block through reversible addition-fragmentation chain transfer polymerization. The RCP block consists of methyl- and lauryl acrylates, the latter of which confers a long-chain alkyl moiety to favorably interact with alkyl-passivated NPs. BCPs showing lamellar, cylindrical, and mixed morphologies were obtained by varying the volume fractions of the RCP block (f RCP ). In comparison to coil-coil BCP, the coil-comb BCPs show highly asymmetric phase behavior with respect to fRCP, where lamellar morphologies were observed at fRCP from 0.31 to 0.51. NPs in the size of 4-5 nm were successfully incorporated in the RCP block of the BCPs with periodicities of 30-60 nm. An order-to-order phase transition from lamellae to PS cylinders was observed after the addition of only 1-2 vol % 5 nm NPs into the BCP with a periodicity of 25 nm and f RCP of 0.51. Self-consistent field theory-density functional theory simulations qualitatively described the observed morphologies and phase transitions in the nanocomposites. Here, the current study presents a platform to fabricate nanocomposites with NP assemblies in coil-comb BCPs that contain a random copolymer block and provides insight into how polymer chain architectures can affect the phase behavior of BCPs and nanocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Coal polymer composites prepared by fused deposition modeling (FDM) 3D printing

Coal is a vital energy resource worldwide, but pollutants and greenhouse gases from its combustion cause environmental problems. To explore the non-combustion approach to use and valorize coal, anthracite and lignite were blended with polyamide 12 (PA 12) through FDM printing in this work and compared in the composites. By adding lignite, Young’s modulus improved with increasing loading to 50 wt% while tensile strength leveled off among the composites, compared to that of PA 12. By contrast, the addition of anthracite decreased the tensile performance at all loadings. Rheology tests and morphology analyses suggested that the interactions between fillers (anthracite and lignite) and PA 12 may cause differences in tensile properties. In addition, the printed lignite composites showed improved thermal conductivity (~ twofold), indicating lignite demonstrates the potential to build functional composites. This work provides a strategy to use lignite in composites by 3D printing for value-added products and reduces the demand for petroleum-based polymers. Overall, our approach diverts lignite from combustion processes and alleviates the negative impact of lignite use on the environment.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Unleashing the potential of waste: A supercharged high-performance 3D printing resin from discarded polylactic acid

In additive manufacturing/3D printing, the limitation no longer lies in people’s imagination but in the very materials that one can print with. While the additive manufacturing process can virtually create any geometry, available applications are often limited by factors like parts’ mechanical strength, glass transition temperature, and heat deflection temperature. These factors are especially critical for polymer-based printing. Here we introduce a simple formulation derived from the aminolysis of polylactic acid (PLA) plastic waste, namely the N-lactoyl ethanolamine (N-LEA). The N-LEA is next reacted with excess methacrylic anhydride, forming a photo-crosslinkable resin for MSLA 3D printing. The resulting 3D printed part has a set of impressive properties that is unrivaled amongst engineering grade 3D printing resins on the market and research literature. The 3D printed part has an ultrahigh tensile strength of 131.7 MPa, glass transition at ~190 °C, and heat deflection temperature at 162.6 °C. Furthermore, this work demonstrates a true upcycling approach for turning PLA waste into a value-added product in a simple and efficient manner while also expanding the high-performance material portfolio available for photocuring additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Characterization of Polyhydroxybutyrate-Based Composites Prepared by Injection Molding

The waste generated by single-use plastics is often non-recyclable and non-biodegradable, inevitably ending up in our landfills, ecosystems, and food chain. Through the introduction of biodegradable polymers as substitutes for common plastics, we can decrease our impact on the planet. In this study, we evaluate the changes in mechanical and thermal properties of polyhydroxybutyrate-based composites with various additives: Microspheres, carbon fibers or polyethylene glycol (2000, 10,000, and 20,000 MW). The mixtures were injection molded using an in-house mold attached to a commercial extruder. The resulting samples were characterized using microscopy and a series of spectroscopic, thermal, and mechanical techniques. We have shown that the addition of carbon fibers and microspheres had minimal impact on thermal stability, whereas polyethylene glycol showed slight improvements at higher molecular weights. All of the composite samples showed a decrease in hardness and compressibility. The findings described in this study will improve our understanding of polyhydroxybutyrate-based composites prepared by injection molding, enabling advancements in integrating biodegradable plastics into everyday products.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Ultra-High-Molecular-Weight Silphenylene/Siloxane Polymers

Elastomers having molecular weights above 1 million made by twostage polymerization. Two-stage process proves far more successful than synthesis from reactive monomers. Process involves synthesis of silanolterminated prepolymer and subsequent extension of prepolymer chain with additional aminosilane monomer. Multistage method allows chain-extending monomer added in precise amounts between stages.

Patterson, W. J.↗
DOE OSTI2023

Polymer Compositions in Critical Experiments: Possibly Not What You Think

The Chlorine Worth Study (CWS) Experiment was performed at the National Criticality Experiments Research Center (NCERC) in December 2021. Its goal was to provide a validation benchmark experiment with chlorine and plutonium in the thermal neutron spectrum. This purpose is necessary to reduce the margin of subcriticality in aqueous chloride operations at the Los Alamos National Laboratory Plutonium Facility (PF-4). Reducing the margin of subcriticality will enable higher throughput, required to meet NNSA mission needs. The experiment used layers of plutonium plates, polyethylene (HDPE), aluminum, and polyvinyl chloride (PVC) or chlorinated polyvinyl chloride (CPVC). They were optimized to match plutonium-chloride solutions of 30 g/L, 300 g/L, and 600 g/L. Upon completion of the experiment, a International Criticality Safety Benchmark Evaluation Program (ICSBEP) report was immediately started. The compositions of all materials were assumed pure unless additional information was known (such as for the plutonium plates). During the benchmark analysis, the assumed CPVC composition was questioned. The follow-on work led to lessons learned on compositions in benchmarks. Materials, and specifically polymers, are often much more complex than a basic chemical formula. The CWS experiment is used as an example in this paper to document the lessons learned.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Shock compression of poly(methyl methacrylate) PMMA in the 1000 GPa regime: Z machine experiments

Hydrocarbon polymers are used in a wide variety of practical applications. In the field of dynamic compression at extreme pressures, these polymers are used at several high energy density (HED) experimental facilities. One of the most common polymers is poly(methyl methacrylate) or PMMA, also called Plexiglass® or Lucite®. Here, we present high-fidelity, hundreds of GPa range experimental shock compression data measured on Sandia’s Z machine. We extend the principal shock Hugoniot for PMMA to more than threefold compression up to 650 GPa and re-shock Hugoniot states up to 1020 GPa in an off-Hugoniot regime, where experimental data are even sparser. These data can be used to put additional constraints on tabular equation of state (EOS) models. The present results provide clear evidence for the need to re-examine the existing tabular EOS models for PMMA above ~120 GPa as well as perhaps revisit EOSs of similar hydrocarbon polymers commonly used in HED experiments investigating dynamic compression, hydrodynamics, or inertial confinement fusion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Ion Conducting Polymer Interfaces for Lithium Metal Anodes: Impact on the Electrodeposition Kinetics

Electrochemical cells that utilize metals (e.g., lithium, sodium, zinc) as anodes are under intense investigation as they are projected to replace the current lithium-ion batteries to serve as a more energy-dense option for commercial applications. In addition, metal electrodes provide opportunities for fundamental research of different phenomena, such as ion transport and electrochemical kinetics, in the complex environment of reactive metal-electrodeposition. In this work, computationally and experimentally the competing effects related to transport and kinetics during the metal electrodeposition process are examined. Using Brownian dynamics simulations, it is shown that slower deposition kinetics results in a more compact and uniform Li morphology. This finding is experimentally implemented by designing ion-containing polymeric coatings on the electrodes that simultaneously provide pathways for lithium-ion transport, while impeding the charge transfer (Li + + e - → Li) at heterogeneous surfaces. It is further shown that these ionic polymer interfaces can significantly extend the cell-lifetime of a lithium metal battery in both ether-based and carbonate-based electrolytes. Through theoretical and experimental investigations, it is found that a low kinetic to transport rate ratio is a major factor in influencing the Li plating morphology. The plating morphology can be further fine-tuned by increasing ionic conductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recycled Cardboard Containers as a Low Energy Source for Cellulose Nanofibrils and Their Use in Poly(l-lactide) Nanocomposites

Cellulose nanomaterials have attracted a great deal of interest as sustainable alternatives to nonrenewable or fossil fuel-derived materials, particularly in composite applications. Cellulose nanofibrils (CNF) are most often derived from wood sources through energy-intensive and costly mechanical fibrillation processes. Here, recycled cardboard, referred to as old corrugated cardboard (OCC), was investigated as an alternate CNF source. OCC is a recycled material that can be obtained at one-tenth the cost of the commonly used bleached softwood Kraft pulp and can be refined to similar levels with nearly one-half of the energy consumption. Additionally, the distinct composition and morphology of OCC-derived CNF provides a more favorable fiber–matrix interface and better reinforcement capabilities of the cellulose nanofibrils in polymer matrices, displaying an over 70% increase in tensile modulus at a loading of 40 wt % with no decrease in tensile strength. When paired with biobased poly(l-lactide) (PLLA), OCC-derived CNF is proven to be an attractive low-cost and low-energy reinforcing agent for sustainable, high performance nanocomposites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗