Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oil”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Wettability Alteration with Weak Acid-Assisted Surfactant Flood

Oil-wetness and heterogeneity are two key reasons for low oil recovery by waterflooding in carbonate reservoirs. Surfactants have been effective in altering the oil-wet matrix to a more water-wet condition and initiating spontaneous imbibition. Because it takes time for the surfactant to alter wettability, oil recovery from the tight matrix is slow and sometimes not economically feasible. Acids have the potential of dissolving minerals, which may alter wettability. In this study, the enhanced oil recovery (EOR) performance of an acid-assisted surfactant solution, a novel technique, was evaluated for low-temperature applications. A set of acids and their acetates were tested. Bulk rock-acid reaction, wettability alteration (WA) tests, and spontaneous imbibition measurements were conducted at reservoir temperature (35°C) to identify effective candidates. Coreflood tests were then performed to evaluate the selected acid-surfactant formulations. Before and after a coreflood test, the core was scanned using micro-computed tomography (CT) to investigate pore structure alteration. Bulk reaction measurements showed that weak acids, especially acetic acid (AA), have the desired low reaction rates at 35°C. WA tests showed that AA can remove the crude oil off the rock surface and alter wettability through mineral dissolution. The surfactant can reduce contact angles from 160° to 58°; adding acid into the surfactant can further reduce it to 52°. Spontaneous imbibition experiments showed the synergy between the acid and the surfactant; the AA-surfactant solution had the highest oil recovery (62.6%) among acid-surfactant formulations. The acid improves the WA efficiency by the surfactant through surface mineral dissolution and lower ζ-potential. The imbibition transports the acid-surfactant solutions into the matrix, which minimizes face dissolution. Coreflood tests show that the AA-surfactant flood can increase the oil recovery rate and recover about 8% more oil compared to the surfactant flood. Micro-CT showed that a few mineral particles were transported along the core and partially plugged pore throats, which reduced permeability and diverted flow leading to improved oil recovery. Here, the transport of the acid in reservoirs and the potential plugging issues have to be carefully evaluated in future studies.

58 GEOSCIENCES↗
DOE OSTI2023

Comparison of the Chemical Composition of Liquids from the Pyrolysis and Hydrothermal Liquefaction of Lignocellulosic Materials

Major differences in thermal stability and hydrotreatment behavior of HTL and pyrolysis oils have been reported in the literature. However, little is known about the variations in the chemical composition of these oils that could explain such differences. Two commercial wood pyrolysis oils (Pyrovac and BTG), and their water-soluble (WS) and water-insoluble fractions (WIS) were analyzed and compared with the aqueous (WS WD-57 ) and oily (WIS WS-57 ) fractions obtained from hydrothermal liquefaction (HTL) of Douglas-fir. The samples were characterized by GC/MS, Karl Fischer titration, carbonyl content, total acid number, elemental composition, calorific value, proximate analysis, Fourier Transform Infrared Spectroscopy (FTIR), Folin-Ciocalteu (FC), and UV fluorescence. All the fractions were also analyzed by Fourier Transform Ion Cyclotron Resonance Mass Spectroscopy (FT-ICR-MS) and by Electrospray Ionization (EI). The most prevalent class of compounds in the water insoluble phases were phenols derived from lignin. Water-soluble phases contain mostly the oxygenated compounds derived from cellulose and hemicellulose and were richer in carbonyl functional groups. The water content of the resulting aqueous phases were between: 65 (WS BTG ) and 96 (WS Pyrovac ) wt. %. The bio-oil from BTG has higher water content and lower HHV, compared to Pyrovac oil. The GC/MS results of BTG oil show the presence of a more prominent acetic acid peak and higher TAN number than the Pyrovac oil. The GC/MS of Pyrovac oil showed more obvious mono-phenol peaks. The quantification of this family by Folin-Ciocalteu method confirmed higher content of monophenolic compounds compared with the BTG oil. The lower thermal stability of pyrolysis oils compared with HTL biocrudes can be partially explained by the fact that pyrolysis oils (BTG and Pyrovac) contain carbohydrates while HTL biocrude (WIS WD-57 ) doesn’t. Thus, we decided to further investigate the chemical differences between the phenolic rich fractions insoluble in water and the holocellulose derived compounds soluble in water. Even after water extraction, the acid content of the water insoluble fraction from BTG (WISBTG) was higher than the acid content of the water insoluble fraction obtained by HTL (WISWSD-57). Likewise, the acid content of the aqueous phases derived from pyrolysis oils (WS Pyrovac , WS BTG ) was also higher than for the aqueous phase obtained by HTL (WSWSD-57). This result is in part due to the use of bases in the HTL process that neutralizes the acid formed in that process. Moreover, the starting feedstock may also influence the differences between the oils. Although, the UV-Fluorescence spectra, ICR-MS and the EI analyses showed some minor differences in the molecular weight and chemical make-up of the oligomers soluble and insoluble in water from pyrolysis and HTL; the differences observed were not large enough to justify the differences in behavior between these oils reported in the literature. Our results suggest that the differences observed between HTL biocrudes and pyrolysis oils are likely partially due to the presence of holocellulose derived products in the pyrolysis oils and higher acid contents.

09 BIOMASS FUELS↗
NASA NTRS2006

Advances in Measurement of Skin Friction in Airflow

The surface interferometric skin-friction (SISF) measurement system is an instrument for determining the distribution of surface shear stress (skin friction) on a wind-tunnel model. The SISF system utilizes the established oil-film interference method, along with advanced image-data-processing techniques and mathematical models that express the relationship between interferograms and skin friction, to determine the distribution of skin friction over an observed region of the surface of a model during a single wind-tunnel test. In the oil-film interference method, a wind-tunnel model is coated with a thin film of oil of known viscosity and is illuminated with quasi-monochromatic, collimated light, typically from a mercury lamp. The light reflected from the outer surface of the oil film interferes with the light reflected from the oil-covered surface of the model. In the present version of the oil-film interference method, a camera captures an image of the illuminated model and the image in the camera is modulated by the interference pattern. The interference pattern depends on the oil-thickness distribution on the observed surface, and this distribution can be extracted through analysis of the image acquired by the camera. The oil-film technique is augmented by a tracer technique for observing the streamline pattern. To make the streamlines visible, small dots of fluorescentchalk/oil mixture are placed on the model just before a test. During the test, the chalk particles are embedded in the oil flow and produce chalk streaks that mark the streamlines. The instantaneous rate of thinning of the oil film at a given position on the surface of the model can be expressed as a function of the instantaneous thickness, the skin-friction distribution on the surface, and the streamline pattern on the surface; the functional relationship is expressed by a mathematical model that is nonlinear in the oil-film thickness and is known simply as the thin-oil-film equation. From the image data acquired as described, the time-dependent oil-thickness distribution and streamline pattern are extracted and by inversion of the thin-oil-film equation it is then possible to determine the skin-friction distribution. In addition to a quasi-monochromatic light source, the SISF system includes a beam splitter and two video cameras equipped with filters for observing the same area on a model in different wavelength ranges, plus a frame grabber and a computer for digitizing the video images and processing the image data. One video camera acquires the interference pattern in a narrow wavelength range of the quasi-monochromatic source. The other video camera acquires the streamline image of fluorescence from the chalk in a nearby but wider wavelength range. The interference- pattern and fluorescence images are digitized, and the resulting data are processed by an algorithm that inverts the thin-oil-film equation to find the skin-friction distribution.

Brown, James L.↗
DOE OSTI2020

Pilot plant reliability metrics for grinding and fast pyrolysis of woody residues

Here we report on the effects of loblolly pine residue variability on material throughput, pilot plant uptime, operator intervention, product yield, and product quality for grinding, fast pyrolysis, and hydrotreating operations. Preprocessing throughput using a hammer mill varied between 31-48% of nameplate capacity (5 tons/hr). Grinder overloads in the size reduction step were more prevalent for lower ash and higher moisture materials. Fast pyrolysis throughput varied between 57-72% of nameplate capacity (20 kg/hr) and bio-oil yields varied between 46-53% (feedstock carbon to oil, dry basis). During fast pyrolysis operations, downtime was caused by bridging in the feed and char removal systems and plugging in the condensation system. Cohesion of feedstock and char leading to system plugging was less frequent for higher ash feedstocks, and differences in condenser plugging behavior between high and low ash feedstocks were observed. The catalyst stability of the bio-oil stabilization step was strongly dependent on the sulfur content in the bio-oil, which was higher for the high-ash residue oils. Lower moisture content in the starting biomass was consistent with lower sulfur content in bio-oil. Yields and properties of hydrotreated fuel products showed minimal deference among the bio-oils.

Klinger, Jordan↗