Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mooring system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

OC6 Phase Ia: CFD Simulations of the Free-Decay Motion of the DeepCwind Semisubmersible

Currently, the design of floating offshore wind systems is primarily based on mid-fidelity models with empirical drag forces. The tuning of the model coefficients requires data from either experiments or high-fidelity simulations. As part of the OC6 (Offshore Code Comparison Collaboration, Continued, with Correlation, and unCertainty (OC6) is a project under the International Energy Agency Wind Task 30 framework) project, the present investigation explores the latter option. A verification and validation study of computational fluid dynamics (CFD) models of the DeepCwind semisubmersible undergoing free-decay motion is performed. Several institutions provided CFD results for validation against the OC6 experimental campaign. The objective is to evaluate whether the CFD setups of the participants can provide valid estimates of the hydrodynamic damping coefficients needed by mid-fidelity models. The linear and quadratic damping coefficients and the equivalent damping ratio are chosen as metrics for validation. Large numerical uncertainties are estimated for the linear and quadratic damping coefficients; however, the equivalent damping ratios are more consistently predicted with lower uncertainty. Some difference is observed between the experimental and CFD surge-decay motion, which is caused by mechanical damping not considered in the simulations that likely originated from the mooring setup, including a Coulomb-friction-type force. Overall, the simulations and the experiment show reasonable agreement, thus demonstrating the feasibility of using CFD simulations to tune mid-fidelity models.

17 WIND ENERGY↗
NASA NTRS1976

The formation of Saturn's satellites and rings, as influenced by Saturn's contraction history

The paper investigates constraints imposed on the ice content of Saturn's satellites and rings by the planet's high luminosity during the early part of its quasi-equilibrium contraction phase. It is assumed that the addition of ices to the satellites was not completed until after the start of the quasi-equilibrium contraction and that the condensation of ices ceased at the same time within the primordial nebulae of Jupiter and Saturn. Using previously derived limits on the time of condensation cessation for Jupiter's system, the following tentative conclusions are made: (1) Titan is the innermost satellite at whose position a methane-containing ice could condense; (2) water ice could have condensed at the positions of all the satellites; (3) the systematic decrease in the mass of the regular satellites with decreasing distance from the planet may have been caused, in part, by the larger time intervals, for the closer satellites, between the start of contraction and the first condensation of ices at their positions; and (4) ammonia ices, primarily NH4SH, were able to condense at the positions of all but the innermost satellites. It is also shown that water ice could have condensed in the region of the rings near the end of the condensation period.

Pollack, J. B.↗
NASA NTRS1988

Weak rotating flow disturbances in a centrifugal compressor with a vaneless diffuser

A theory is presented to predict the occurrence of weak rotating waves in a centrifugal compression system with a vaneless diffuser. As in a previous study of axial systems, an undisturbed performance characteristic is assumed known. Following an inviscid analysis of the diffuser flow, conditions for a neutral rotating disturbance are found. The solution is shown to have two branches; one with fast rotation, the other with very slow rotation. The slow branch includes a dense set of resonant solutions. The resonance is a feature of the diffuser flow, and therefore such disturbances must be expected at the various resonant flow coefficients regardless of the compressor characteristic. Slow solutions seem limited to flow coefficients less than about 0.3, where third and fourth harmonics appear. Fast waves seem limited to a first harmonic. These fast and slow waves are described, and effects of diffuser-wall convergence, backward blade angles, and partial recovery of exit velocity head are assessed.

Moore, F. K.↗
NASA NTRS1991

Payload advisory panel recommendations

The Payload Advisory Panel proposes a restructured Earth Observing System (EOS) mission to address high-priority science and environmental policy issues in Earth System Science. These issues have been identified through studies conducted by the Intergovernmental Panel on Climate Change (IPCC), the United States Environmental Protection Agency (EPA), and the Committee on Earth and Environmental Sciences (CEES). The restructured EOS defers efforts to improve the understanding of the middle and upper stratosphere and solid earth geophysics. The strategy of the mission combines high priority new measurements with continuation of critical data sets begun by missions which precede EOS. Collaborative arrangements with international partners are an essential part of the program and additional arrangements are posed. The need for continuity in Earth observations and the urgency of environmental questions require launch of some EOS elements as soon as possible. They further require maintenance of the EOS objective of obtaining consistent 15-year measurement records.

Moore, Berrien, III↗
DOE OSTI2025

Operation and performance of the CMS silicon strip tracker with proton-proton collisions at the CERN LHC

Salient aspects of the commissioning, calibration, and performance of the CMS silicon strip tracker are discussed, drawing on experience during operation with proton-proton collisions delivered by the CERN LHC. The data were obtained with a variety of luminosities. The operating temperature of the strip tracker was changed several times during this period and results are shown as a function of temperature in several cases. Details of the system performance are presented, including occupancy, signal-to-noise ratio, Lorentz angle, and single-hit spatial resolution. Saturation effects in the APV25 readout chip preamplifier observed during early Run 2 are presented, showing the effect on various observables and the subsequent remedy. Studies of radiation effects on the strip tracker are presented both for the optical readout links and the silicon sensors. The observed effects are compared to simulation, where available, and they generally agree well with expectations.

47 OTHER INSTRUMENTATION↗
NASA NTRS1987

On the sputter alteration of regoliths of outer solar system bodies

Several processes that are expected to occur when the porous regoliths of outer solar system bodies (without atmospheres) are subjected to energetic ion bombardment are discussed. The conclusions reached in much of the literature addressing sputtering are quantitatively or qualitatively incorrect because effects of soil porosity have been neglected. It is shown theoretically and experimentally that porosity reduces the effective sputtering yield of a soil by more than an order of magnitude. Between 90 and 97% of the sputtered atoms are trapped within the regolith, where they are factionated by differential desorption. Experiments indicate that more volatile species have higher desorption probabilities. This process is the most important way in which alteration of chemical and optical properties occurs when a regolith is sputtered. When a basic silicate soil is irradiated these effects lead to sputter-deposited films enriched in metallic iron, while O, Na and K are preferentially lost. The Na and K are present in the atmosphere above the sputtered silicate in quantities much greater than their abundances in the regolith. Icy regoliths of SO2 should be enriched in elemental S and/or S2O. This prediction is supported by the probable identification of S2O and polysulfur oxide bands in the IR spectra of H-sputtered SO2 reported by Moore. When porous mixtures of water, ammonia and methane frosts are sputtered, the loss of H and surface reactions of C, N and O in the deposits should produce complex hydrocarbons and carbohydrates, some of which may be quite dark. Such reactions may have played a role in the formation of the matrix material of carbonaceous chondrites prior to agglomeration.

Hapke, Bruce↗
DOE OSTI2021

Milestone M6 Report: Reducing Excess Data Movement Part 1

This is the second in a sequence of three Hardware Evaluation milestones that provide insight into the following questions: What are the sources of excess data movement across all levels of the memory hierarchy, going out to the network fabric? What can be done at various levels of the hardware/software hierarchy to reduce excess data movement? How does reduced data movement track application performance? The results of this study can be used to suggest where the DOE supercomputing facilities, working with their hardware vendors, can optimize aspects of the system to reduce excess data movement. Quantitative analysis will also benefit systems software and applications to optimize caching and data layout strategies. Another potential avenue is to answer cost-benefit questions, such as those involving memory capacity versus latency and bandwidth. This milestone focuses on techniques to reduce data movement, quantitatively evaluates the efficacy of the techniques in accomplishing that goal, and measures how performance tracks data movement reduction. We study a small collection of benchmarks and proxy mini-apps that run on pre-exascale GPUs and on the Accelsim GPU simulator. Our approach has two thrusts: to measure advanced data movement reduction directives and techniques on the newest available GPUs, and to evaluate our benchmark set on simulated GPUs configured with architectural refinements to reduce data movement.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2011

Molecular Gas in Young Debris Disks

Gas-rich primordial disks and tenuous gas-poor debris disks are usually considered as two distinct evolutionary phases of the circumstellar matter. Interestingly, the debris disk around the young main-sequence star 49 Ceti possesses a substantial amount of molecular gas and possibly represents the missing link between the two phases. Motivated to understand the evolution of the gas component in circumstellar disks via finding more 49 Ceti-like systems, we carried out a CO J = 3-2 survey with the Atacama Pathfinder EXperiment, targeting 20 infrared-luminous debris disks. These systems fill the gap between primordial and old tenuous debris disks in terms of fractional luminosity. Here we report on the discovery of a second 49 Ceti-like disk around the 30 Myr old A3-type star HD21997, a member of the Columba Association. This system was also detected in the CO(2-1) transition, and the reliable age determination makes it an even clearer example of an old gas-bearing disk than 49 Ceti. While the fractional luminosities of HD21997 and 49 Ceti are not particularly high, these objects seem to harbor the most extended disks within our sample. The double-peaked profiles of HD21997 were reproduced by a Keplerian disk model combined with the LIME radiative transfer code. Based on their similarities, 49 Ceti and HD21997 may be the first representatives of a so far undefined new class of relatively old > or approx.8 Myr), gaseous dust disks. From our results, neither primordia1 origin nor steady secondary production from icy planetesima1s can unequivocally explain the presence of CO gas in the disk ofHD21997.

Moor, A.↗
DOE OSTI2022

Design of a multi-detector, single line-of-sight, time-of-flight system to measure time-resolved neutron energy spectra

In the dynamic environment of burning, thermonuclear deuterium–tritium plasmas, diagnosing the time-resolved neutron energy spectrum is of critical importance. Strategies exist for this diagnosis in magnetic confinement fusion plasmas, which presently have a lifetime of ~10 12 longer than inertial confinement fusion (ICF) plasmas. In this work, we present a novel concept for a simple, precise, and scale-able diagnostic to measure time-resolved neutron spectra in ICF plasmas. The concept leverages general tomographic reconstruction techniques adapted to time-of-flight parameter space, and then employs an updated Monte Carlo algorithm and National Ignition Facility-relevant constraints to reconstruct the time-evolving neutron energy spectrum. Reconstructed spectra of the primary 14.028 MeV n DT peak are in good agreement with the exact synthetic spectra. The technique is also used to reconstruct the time-evolving downscattered spectrum, although the present implementation shows significantly more error.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Breaking the mold: Overcoming the time constraints of molecular dynamics on general-purpose hardware

The evolution of molecular dynamics (MD) simulations has been intimately linked to that of computing hardware. For decades following the creation of MD, simulations have improved with computing power along the three principal dimensions of accuracy, atom count (spatial scale), and duration (temporal scale). Since the mid-2000s, computer platforms have, however, failed to provide strong scaling for MD, as scale-out central processing unit (CPU) and graphics processing unit (GPU) platforms that provide substantial increases to spatial scale do not lead to proportional increases in temporal scale. Important scientific problems therefore remained inaccessible to direct simulation, prompting the development of increasingly sophisticated algorithms that present significant complexity, accuracy, and efficiency challenges. While bespoke MD-only hardware solutions have provided a path to longer timescales for specific physical systems, their impact on the broader community has been mitigated by their limited adaptability to new methods and potentials. In this work, we show that a novel computing architecture, the Cerebras wafer scale engine, completely alters the scaling path by delivering unprecedentedly high simulation rates up to 1.144 M steps/s for 200 000 atoms whose interactions are described by an embedded atom method potential. This enables direct simulations of the evolution of materials using general-purpose programmable hardware over millisecond timescales, dramatically increasing the space of direct MD simulations that can be carried out. In this paper, we provide an overview of advances in MD over the last 60 years and present our recent result in the context of historical MD performance trends.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2013

High Speed Mobility Through On-Demand Aviation

Game changing advances come about by the introduction of new technologies at a time when societal needs create the opportunity for new market solutions. A unique opportunity exists for NASA to bring about such a mobility revolution in General Aviation, extendable to other aviation markets, to maintain leadership in aviation by the United States. This report outlines the research carried out so far under NASA's leadership towards developing a new mobility choice, called Zip Aviation1,2,3. The feasibility, technology and system gaps that need to be addressed, and pathways for successful implementation have been investigated to guide future investment. The past decade indicates exciting trends in transportation technologies, which are quickly evolving. Automobiles are embracing automation to ease driver tasks as well as to completely control the vehicle with added safety (Figure 1). Electric propulsion is providing zero tail-pipe emission vehicles with dramatically lower energy and maintenance costs. These technologies have not yet been applied to aviation, yet offer compelling potential benefits across all aviation markets, and in particular to General Aviation (GA) as an early adopter market. The benefits of such an adoption are applicable in the following areas: 􀁸 Safety: The GA market experiences accident rates that are substantially higher than automobiles or commercial airlines, with 7.5 fatal accidents per 100 million vehicle miles compared to 1.3 for automobiles and.068 for airlines. Approximately 80% of these accidents are caused by some form of pilot error, with another 13% caused by single point propulsion system failure. 􀁸 Emissions: Environmental constraints are pushing for the elimination of 100Low Lead (LL) fuel used in most GA aircraft, with aviation fuel the #1 source of lead emissions into the environment. Aircraft also have no emission control systems (i.e. no catalytic converters etc.), so they are gross hydrocarbon polluters compared to automobiles. 􀁸 Community Noise: Hub and smaller GA airports are facing increasing noise restrictions, and while commercial airliners have dramatically decreased their community noise footprint over the past 30 years, GA aircraft noise has essentially remained same, and moreover, is located in closer proximity to neighborhoods and businesses. 􀁸 Operating Costs: GA operating costs have risen dramatically due to average fuel costs of over $6 per gallon, which has constrained the market over the past decade and resulted in more than 50% lower sales and 35% less yearly operations. Infusion of autonomy and electric propulsion technologies can accomplish not only a transformation of the GA market, but also provide a technology enablement bridge for both larger aircraft and the emerging civil Unmanned Aerial Systems (UAS) markets. The NASA Advanced General Aviation Transport Experiments (AGATE) project successfully used a similar approach to enable the introduction of primary composite structures and flat panel displays in the 1990s, establishing both the technology and certification standardization to permit quick adoption through partnerships with industry, academia, and the Federal Aviation Administration (FAA). Regional and airliner markets are experiencing constant pressure to achieve decreasing levels of community emissions and noise, while lowering operating costs and improving safety. But to what degree can these new technology frontiers impact aircraft safety, the environment, operations, cost, and performance? Are the benefits transformational enough to fundamentally alter aircraft competiveness and productivity to permit much greater aviation use for high speed and On-Demand Mobility (ODM)? These questions were asked in a Zip aviation system study named after the Zip Car, an emerging car-sharing business model. Zip Aviation investigates the potential to enable new emergent markets for aviation that offer "more flexibility than the existing transportation solutions." These studies indicate that autonomy and electric propulsion technology infusions offer a unique opportunity to provide breakthrough capabilities for new high speed, on-demand travel alternatives that can leapfrog the need for future expensive ground-based infrastructure investment. At the same time, such investments offer a method of laying the foundation for these technologies to be incubated for commercial aviation at lower cost, and with lower initial certification thresholds due to the relatively poor capabilities of GA aircraft to permit early adoption and private market capitalization by rapid technology accelerations, as depicted in Figure 2.

Moore, Mark D.↗
NASA NTRS2022

Frequency Agile Solar Radiotelescope

The Frequency Agile Solar Radiotelescope (FASR) has been strongly endorsed as a top community priority by both Astronomy & Astrophysics Decadal Surveys and Solar & Space Physics Decadal Surveys in the past two decades. Although it was developed to a high state of readiness in previous years (it went through a CATE analysis and was declared “doable now”), the NSF has not had the funding mechanisms in place to fund this mid-scale program. Now it does, and the community must seize this opportunity to modernize the FASR design and build the instrument in this decade. The concept and its science potential have been abundantly proven by the pathfinding Expanded Owens Valley Solar Array (EOVSA), which has demonstrated a small subset of FASR’s key capabilities such as dynamically measuring the evolving magnetic field in eruptive flares, the temporal and spatial evolution of the electron energy distribution in flares, and the extensive coupling among dynamic components (flare, flux rope, current sheet). The FASR concept, which is orders of magnitude more powerful than EOVSA, is low-risk and extremely high reward, exploiting a fundamentally new research domain in solar and space weather physics. Utilizing dynamic broadband imaging spectropolarimetry at radio wavelengths, with its unique sensitivity to coronal magnetic fields and to both thermal plasma and nonthermal electrons from large flares to extremely weak transients, the ground-based FASR will make synoptic measurements of the coronal magnetic field and map emissions from the chromosphere to the middle corona in 3D. With its high spatial, spectral, and temporal resolution, as well as its superior imaging fidelity and dynamic range, FASR is poised to provide a system-wide perspective on myriad coupled phenomena. FASR will be a highly complementary and synergistic component of solar and heliospheric observing capabilities that is critically needed to support the next generation of solar science.

Dale E. Gary↗
NASA NTRS2011

Do Titan's Mountains Betray the Late Acquisition of its Current Atmosphere

Titan may have acquired its massive atmosphere relatively recently in solar system history [1,2,3,4]. Prior to that time, Titan would have been nearly airless, with its volatiles frozen or sequestered. Present-day Titan experiences only small (approximately 4 K) pole-to-equator variations, owing to efficient heat transport via the thick atmosphere [5]; these temperature variations would have been much larger (approximately 20 K) in the absence of an atmosphere. If Titan's ice shell is conductive, the change in surface temperature associated with the development of an atmosphere would have led to changes in shell thickness. In particular, the poles would move down (inducing compression) while the equator would move up. Figure 1 shows the predicted change in surface elevation as a result of the change in surface temperature, using the numerical conductive shell thickness model of [6]

Moore, Jeffrey Morgan↗
DOE OSTI2024

TATB thermal decomposition: Expanding the molecular profile with cryo-focused pyrolysis GC-MS

Understanding the molecular composition of high explosives during thermal decomposition is vital for predicting the sensitivity, safety, and performance of explosive materials. The thermal decomposition of 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) has been linked to the formation of furazans through a series of dehydration reactions of the NO2 and NH2 groups on the phenyl ring, along with breakdown into small molecules (≤120 amu). Molecular identification of compounds formed in this transformation of the furazans to light gases has been lacking. To address this, we have applied a pseudo-confined sampling system in a cryo-focused pyrolysis gas chromatography-mass spectrometry (pyGC-MS) system to molecularly identify these intermediates. By design, sublimation of TATB, which has complicated MS analyses of thermal degradation, was significantly reduced and additional compounds were identified with potential structural information. In addition to the known furazan compounds, one of these compounds forms from the loss of oxygen from benzo-trifurazan (F3) and produces an open ring structure that may be the first step in the formation of lower molecular weight furazan breakdown products. The loss of a nitro group from benzo-monofurazan (F1) was also discovered and implicates the formation of oxidizing NO2 gas in the thermal decomposition mechanism. So these findings are vital for understanding the proper heat flow from energetic materials on a molecular level, necessary when measuring enthalpy and developing decomposition models based on kinetic parameters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Strength mechanisms and tunability in Al-Ce-Mg ternary alloys enabled by additive manufacturing

Al-Ce-based alloys are promising candidates for additive manufacturing (AM) due to their hot-cracking resistance and because they do not require heat treatment to obtain precipitation strengthening. Rapid solidification rates enabled by AM methods can lead to enhanced mechanical properties; however, the strengthening mechanisms over large composition ranges were unclear. Here, combinatorial synthesis by directed-energy deposition (DED) and hardness measurements were used to rapidly map the composition-dependent strength of the ternary Al-Ce-Mg system. Tensile testing and microstructure characterization of selected compositions were performed to elucidate the compositional dependence of the strengthening mechanisms. Al 11 Ce 3 precipitates were present in all cases, and the maximum hardness (1.25 GPa) was measured for the Al-8Ce-10Mg composition. A combination of (i) Hall-Petch strengthening, based on the FCC-matrix-phase cell size; (ii) particle strengthening, based on Al 11 Ce 3 volume fraction and size; and (iii) solid-solution strengthening, based on Mg composition of the matrix phase, were used to account for the measured strengths. Vickers hardness is shown to correlate well with ultimate tensile strength in these alloys, highlighting the value of surface-based techniques for rapid screening.

36 MATERIALS SCIENCE↗
NASA NTRS2007

Recirculation of Laser Power in an Atomic Fountain

A new technique for laser-cooling atoms in a cesium atomic fountain frequency standard relies on recirculation of laser light through the atom-collection region of the fountain. The recirculation, accomplished by means of reflections from multiple fixed beam-splitter cubes, is such that each of two laser beams makes three passes. As described below, this recirculation scheme offers several advantages over prior designs, including simplification of the laser system, greater optical power throughput, fewer optical and electrical connections, and simplification of beam power balancing. A typical laser-cooled cesium fountain requires the use of six laser beams arranged as three orthogonal pairs of counter-propagating beams to decelerate the atoms and hold them in a three-dimensional optical trap in vacuum. Typically, these trapping/cooling beams are linearly polarized and are positioned and oriented so that (1) counter-propagating beams in each pair have opposite linear polarizations and (2) three of the six orthogonal beams have the sum of their propagation directions pointing up, while the other three have the sum of their propagation directions pointing down. In a typical prior design, two lasers are used - one to generate the three "up" beams, the other to generate the three "down" beams. For this purpose, the output of each laser is split three ways, then the resulting six beams are delivered to the vacuum system, independently of each other, via optical fibers. The present recirculating design also requires two lasers, but the beams are not split before delivery. Instead, only one "up" beam and one oppositely polarized "down" beam are delivered to the vacuum system, and each of these beams is sent through the collection region three times. The polarization of each beam on each pass through the collection region is set up to yield the same combination of polarization and propagation directions as described above. In comparison with the prior design, the present recirculating design utilizes the available laser light more efficiently, making it possible to trap more atoms at a given laser power or the same number of atoms at a lower laser power. The present design is also simpler in that it requires fewer optical fibers, fiber couplings, and collimators, and fewer photodiodes for monitoring beam powers. Additionally, the present design alleviates the difficulty of maintaining constant ratios among power levels of the beams within each "up" or "down" triplet.

Enzer, Daphna G.↗
NASA NTRS2018

The Geology of the Pluto System

NASA's New Horizons mission acquired a large set of images and other data making possible thorough geological analysis of landscapes in the Pluto System. Pluto and Charon exhibit strikingly different surface appearances, despite their similar densities and presumed bulk compositions. Systematic investigation, modelling and mapping revealed that much of Pluto's surface is attributed to surface-atmosphere interactions and the mobilization of volatile ices by insolation. Many mapped valley systems appear to be the consequence of glaciation involving nitrogen ice. Other geological activity requires or required long periods of internal heating, such as Pluto's extensive tectonic fabric. The convection and advection of volatile ices in Sputnik Planitia are thought to be powered by present-day radiogenic heat loss. The prominent mountains at the western margin of Sputnik Planitia, and the strange, multi-km-high mound features to the south, probably composed of H2O, are young geologically as inferred by light cratering and superposition relationships. These multi-km-high mound features might be cryo-volcanoes. Their origin, and what drove their formation so late in Solar System history, is under investigation. East of Sputnik Planitia are large fields of aligned ranks of sharp-crested ridges found only at high altitude that are apparently composed of massive deposits of CH4 ice, referred to as Bladed Terrain. New Horizons found evidence that Bladed Terrain may cover much of Pluto's low latitudes and may have originally formed there as a consequence of Pluto's very high obliquity. Currently Bladed Terrain is undergoing net erosion. This observation, along with evidence for formally more extensive nitrogen glaciation implies that Pluto undergoes significant climate evolution. The dynamic remolding of landscapes by volatile transport seen on Pluto is not unambiguously evident in the mapping of Charon. Charon does, however, display a large resurfaced plain and globally engirdling extensional tectonic network attesting to its early endogenic vigor.

Moore, J. M.↗
DOE OSTI2024

GAMPix: a novel fine-grained, low-noise and ultra-low power pixelated charge readout for TPCs

Here, we report on the development of a novel pixel charge readout system, Grid Activated Multi-scale pixel readout (GAMPix), which is under development for use in the GammaTPC gamma ray instrument concept. GammaTPC is being developed to optimize the use of liquid argon time projection chamber technology for gamma ray astrophysics, for which a fine grained low power charge readout is essential. GAMPix uses a new architecture with coarse and fine scale instrumented electrodes to solve the twin problems of loss of measured charge after diffusion, and high readout power. Fundamentally, it enables low noise and ultra low power charge readout at the spatial scale limited by diffusion in a time projection chamber, and has other possibly applications, including future DUNE modules.

Shutt, Tom↗