Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “moderator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Aligned Conjugated Polymer Nanofiber Networks in an Elastomer Matrix for High-Performance Printed Stretchable Electronics

Conjugated polymer films are promising in wearable X-ray detection. However, achieving optimal film microstructure possessing good electrical and detection performance under large deformation via scalable printing remains challenging. Herein, we report bar-coated high-performance stretchable films based on a conjugated polymer P(TDPP-Se) and elastomer SEBS blend by optimizing the solution-processing conditions. The moderate preaggregation in solution and prolonged growth dynamics from a solvent mixture with limited dissolving capacity is critical to forming aligned P(TDPP-Se) chains/crystalline nanofibers in the SEBS phase with enhanced π–π stacking for charge transport and stress dissipation. The film shows a large elongation at break of >400% and high mobilities of 5.29 cm 2 V –1 s –1 at 0% strain and 1.66 cm 2 V –1 s –1 over 500 stretch–release cycles at 50% strain, enabling good X-ray imaging with a high sensitivity of 1501.52 μC Gy air –1 cm –2 . Finally, our work provides a morphology control strategy toward high-performance conjugated polymer film-based stretchable electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Current-Phase Relations of Superconducting PtSi Constriction Josephson Junctions

Here, we study the current-phase relations of superconductor–constriction–superconductor Josephson junctions made from platinum silicide thin films by fabricating dc-superconducting quantum interference devices incorporating pairs of junctions and measuring their magnetic-field-dependent electrical transport. By comparing the supercurrent interference patterns with numerical Ginzburg–Landau simulations, we extract the current-phase relations of individual junctions and quantify the degree of nonlinearity. These measurements show that while the constrictions themselves sustain substantial nonlinearity, the effect is moderated by the kinetic inductance of the device leads, which is an important consideration for practical superconducting circuit applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Design Rules for Open-Shell Molecular Wires: Insights from Correlated Many-Body Transport

Open-shell π-conjugated systems have emerged as promising molecular wires that can sustain unusually high low-bias conductance over tens of nanometers. However, predictive design rules remain limited because near-degeneracy and spin polarization give rise to correlated electronic states that are not reliably captured by standard density functional theory and Landauer transport descriptions. Here, we establish physically transparent design rules for long-range, weakly length-dependent charge transport based on the interplay between bond-length alternation and electron–electron interactions. Using a fully correlated transport framework that combines density matrix renormalization group calculations with nonequilibrium Green’s function embedding, we show that weak dimerization maintains spatially extended edge states, while moderate on-site interaction stabilizes open-shell character without excessively separating transport-relevant resonances. This balance yields zero-bias transmission that is largely insensitive to molecular length, providing a route to connect chemically tunable structure to correlated transport beyond mean-field descriptions.

Charge transport↗
DOE OSTI2022

Copper Iodide-Mediated Synthesis of α-Diimine Ligands from Bis(imidoyl chlorides) and Arylstannanes

Aryl-substitued α-diimines were prepared by employing an operationally simple copper iodide-mediated Stille type coupling between polyfluoro(chloro)aryl tributylstannanes and bis(imidoyl chlorides). Reactions proceed in commercial grade N, N-dimethylformamide (DMF) solvent at 70 ºC and require no additives or bases. Couplings are successful for aryl stannanes possessing two or more fluoro or chloro substituents on the aromatic ring. Products are obtained in moderate to good yields. Furthermore, this methodology allows for a simple synthesis of α-diimine ligands potentially useful in olefin polymerization as well as other catalytic transformations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The Curious Case of [AnH(NR 2 ) 3 ] (An = Th, U; R = SiMe 3 ): Two Monomeric Actinide Hydrides Revisited

The reaction of AnCl 4 (DME) x (An = Th, x = 2; An = U, x = 0) with 4 equiv of NaNR 2 (R = SiMe 3 ) in THF at 65 °C results in the formation of [An{N(R)(SiMe 2 CH 2 )}(NR 2 ) 2 ] (An = U, 1; An = Th, 2), and not the reported monomeric actinide hydrides, [AnH(NR 2 ) 3 ], as expected. Furthermore, both complexes 1 and 2 were characterized by X-ray crystallography. Surprisingly, their unit cell parameters are remarkably close to those reported for [AnH(NR 2 ) 3 ], suggesting that the original crystals of [AnH(NR 2 ) 3 ] were, in fact, [An{N(R)(SiMe 2 CH 2 )}(NR 2 ) 2 ], but were misidentified. Reduction of 1 with 1.1 equiv of KC 8 in THF, in the presence of 1 equiv of 2.2.2-cryptand, results in the formation of [K(2.2.2-cryptand)][U{N(R)(SiMe 2 CH 2 )}(NR 2 ) 2 ] (3) in good yield. Likewise, the reaction of 1 with 1 equiv of bis(diisopropylamino)cyclopropenylidene (BAC) results in the formation of the BAC adduct, [(BAC)U{N(R)(SiMe 2 CH 2 )}(NR 2 ) 2 ] (4), in moderate yield. Finally, the addition of H 2 (10 bar) to 2 in C 6 D 6 at room temperature results in the formation of the targeted monomeric hydride, [ThH(NR 2 ) 3 ], in 32% yield, according to integrations against an internal standard. However, removal of the H 2 atmosphere results in rapid reformation of 2. In contrast, the addition of H 2 (10 bar) to 1 in C 6 D 6 at room temperature results in no apparent reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Si–Cl Bond Activations at Ni(0) to Give Bimetallic Ni(I) μ 1,2 -Cl–SiR 1 R 2 Complexes that Undergo Selective Hydrogenolyses to R 1 R 2 SiH 2 Dihydrosilanes

Chlorosilanes are cheap and abundant raw materials as crucial building blocks in silicon chemistry, yet the metal-mediated activation and functionalization of Si–Cl bonds typically require precious metal sources due to their thermodynamic inertness. Herein, we report the stoichiometric, facile activation, and hydrogenolysis of chlorosilanes mediated by a series of low-valent NHC–Ni (NHC = N-heterocyclic carbene) complexes. Treatment of a Ni(0) complex (IPr)Ni(η 6 -toluene) (IPr = 1,3-bis(2,6-diisopropylphenyl)imidazole-2-ylidene) with chlorosilanes (R 1 R 2 SiCl 2 , R 1 = Cl, R 2 = Cl, Me, Ph, or R 1 = R 2 = Me, Et, Ph, 4-MePh) rapidly afforded di-Ni(I) complexes with a bridging silyl ligand ([(IPr)Ni] 2 (μ-SiR 1 R 2 Cl)(μ-Cl), 1 R1,R2 ) in high yields. Use of a bulkier chlorosilane, Ph 2 SiCl 2 , allowed the isolation of the mono-Ni(II) silyl complex (IPr)Ni(SiPh 2 Cl)Cl (2 Ph ) as an intermediate generated via Si–Cl oxidative addition, which underwent comproportionation with (IPr)Ni(η 6 -toluene) to form 1 Ph,Ph in nearly quantitative yield. Interestingly, 1 R1,R2 was found to react with H 2 at room temperature to form mono- or di-hydrosilanes in moderate to high yields, and the product selectivity was found to be highly dependent on the identity of substituents on Si. In conclusion, these results demonstrate a novel example of facile Si–Cl activation and hydrogenolysis mediated by low-valent mono- and dinuclear NHC–Ni complexes under mild conditions.

Liu, Tianchang [University of California, Berkeley↗
DOE OSTI2022

Penta-SiCN: A Highly Auxetic Monolayer

We report the negative Poisson’s (NPR) ratio in a two-dimensional (2D) material is a counterintuitive mechanical property that facilitates the development of nanoscale devices with sophisticated functionality. Inspired by the peculiar buckled lower-symmetric, trilayered geometry of pentagonal monolayers, we theoretically predict penta-SiCN, a ternary auxetic metallic monolayer with highly tunable NPR. The penta-SiCN is structurally, thermally, dynamically, and mechanically stable, and sustainable at and beyond room temperature with experimental feasibility. It possesses nontrivial geometrical and mechanical isotropy and relatively moderate thickness. Remarkably, the shorter and quasi sp3-hybridized C–N bond and the rigidity against the strain allow the monolayer to possess a high value of NPR (-0.136), even higher than that of black phosphorene, extendable up to -0.639 by 4% of biaxial stretching. On the other hand, the 2D Young’s modulus of 129.88 N/m decreases to 41.34 N/m at equivalent stretching, indicating relative softening and flexibility. Interestingly, a buckled-to-planar phase transition is identified at 10% biaxial strain before it suffers the fracture at 16%. Additionally, the strong optical anisotropy, absorbance (up to 6.51 x 105 cm -1 ), and presence of plasmon frequency demonstrate its potential application in optomechanical and plasmonics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Importance of the Heat Treatment Scheme on Self-Reducing Reactive Silver Inks

Self-reducing reactive silver inks can print high-quality silver at reasonable temperatures. While numerous studies have explored the impact of processing temperature on electrical properties, the role of the heat treatment scheme has not yet been studied. Common heat treatment schemes include printing and drying inks at room temperature before heat treatment, performing heat treatments while the inks are still wet, and directly printing the inks onto heated substrates. Each scheme generates distinct heat transfer and mass transport kinetics that can affect the silver morphology and electrical properties. However, to date, the impact of different schemes has not been systematically investigated. To address this knowledge gap, this work investigates how different heat treatment schemes impact metal formation, sintering, and the resultant electrical properties of printed self-reducing reactive silver inks. Heat treatment on room-temperature dried inks and wet inks, with top-down (oven) and bottom-up (hot plate) heating sources, were compared. Inks dried at room temperature resulted in extremely porous films that required high heat treatment temperatures (>100 °C) for silver densification. However, these dried films could only densify locally, and their high initial porosities resulted in voids and high resistances (~0.6 Ω mm –1 ) even after heat treatments above 300 °C. Inks that were wet during heat treatment showed moderate improvements in electrical properties with resistances on the order of 0.4 Ω mm –1 at heat treatments of 250 °C. Printing reactive inks directly onto heated substrates yielded the best low-temperature results, with 0.46 Ω mm –1 (5.5 × bulk silver) line resistances achieved at only 90 °C. Overall, this work’s experimental results provide detailed insights into why printing onto a heated substrate results in superior electrical performance compared to more common heat treatment schemes. Additionally, controlling where the precipitation reaction occurs is critical to controlling the film morphology and properties. As a result, this work shows that even an ammonia-based silver reactive ink can achieve good, low-temperature electrical properties with the proper heat treatment scheme.

14 SOLAR ENERGY↗
DOE OSTI2024

Elucidating the Role of InGaAs and InAlAs Buffers on Carrier Dynamics of Tensile-Strained Ge Double Heterostructures

Extensive research efforts of strained germanium (Ge) are currently underway due to its unique properties, namely, (i) possibility of band gap and strain engineering to achieve a direct band gap, thus exhibiting superior radiative properties, and (ii) higher electron and hole mobilities than Si for upcoming technology nodes. Realizing lasing structures is vital to leveraging the benefits of tensile-strained Ge (ε-Ge). Here, we use a combination of different analytical tools to elucidate the effect of the underlying InGaAs/InAlAs and InGaAs overlaying heterostructures on the material quality and strain state of ε-Ge grown by molecular beam epitaxy. Using X-ray analysis, we show the constancy of tensile strain in sub-50 nm ε-Ge in a quantum-well (QW) heterostructure. Further, effective carrier lifetime using photoconductive decay as a function of buffer type exhibited a high (low) defect-limited carrier lifetime of ~68 ns (~13 ns) in 0.61% (0.66%) ε-Ge grown on an InGaAs (InAlAs) buffer. These results correspond well with the measured surface roughness of 1.289 nm (6.303 nm), consistent with the surface effect of the ε-Ge/III–V heterointerface. Furthermore, a reasonably high effective lifetime of ~78 ns is demonstrated in a QW of ~30 nm 1.6% ε-Ge, a moderate reduction from ~99 ns in uncapped ε-Ge, alluding to the surface effect of the overlying heterointerface. Thus, the above results highlight the prime quality of ε-Ge that can be achieved via III–V heteroepitaxy and paves a path for integrated Ge photonics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Enhanced Neutron and γ-Ray Detection via 6 Li Substitution in Undoped and Tl-Doped Zero-Dimensional Perovskite Cs 3 Cu 2 I 5 Scintillators

Radiation detectors are crucial in a wide variety of research and commercial applications, such as oil and gas exploration, medical imaging, nuclear nonproliferation, and homeland security. Neutron and gamma-ray detectors are fundamental components in portal monitors at ports and border crossings, bolstering national security against radiological threats. This study presents a dual-mode scintillator, undoped and Tl-doped 6 Li-Cs 3 Cu 2 I 5 , and demonstrates its potential as a promising material for simultaneous thermal neutron and gamma-ray detection. We explore the Bridgman growth of both undoped and thallium doped Li → Cu and Li → Cs substitutional systems with various Li doping levels and assess their impact on scintillation properties. Under 662 keV gamma-ray excitation, the undoped crystals had light yields up to 35,900 ph/MeV, with energy resolutions down to 4.5%. The Tl-doped crystals performed better than the undoped crystals with light yields peaking at 65,900 ph/MeV and energy resolutions as low as 3.5%. When exposed to a moderated 252 Cf excitation source, our crystals had light yields between 102,900 and 167,200 photons per thermal neutron capture, with a full energy thermal neutron peak reaching 3 MeV in gamma equivalent energy. Pulse shape discrimination studies reveal well-separated gamma and neutron events, resulting in Figure-Of-Merit (FOM) as high as 3.7. Furthermore, these findings highlight the potential of Li-doped Cs 3 Cu 2 I 5 as a viable candidate for next-generation dual-mode scintillators.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Identifying and Tuning the In Situ Oxygen-Rich Surface of Molybdenum Nitride Electrocatalysts for Oxygen Reduction

Rigorous in situ studies of electrocatalysts are required to enable the design of higher performing materials. Nonplatinum group metals for oxygen reduction reaction (ORR) catalysis containing light elements such as O, N, and C are known to be susceptible to both ex situ and in situ oxidation, leading to challenges associated with ex situ characterization methods. We have previously shown that the bulk O content plays an important role in the activity and selectivity of Mo–N catalysts, but further understanding of the role of composition and morphological changes at the surface is needed. Here, we report the measurement of in situ surface changes to a molybdenum nitride (MoN) thin film under ORR conditions using grazing incidence X-ray absorption and reflectivity. We show that the half-wave potential of MoN can be improved by ~90 mV by potential conditioning up to 0.8 V versus RHE. Utilizing electrochemical analysis, dissolution monitoring, and surface-sensitive X-ray techniques, we show that under moderate polarization (0.3–0.7 V vs RHE) there is local ligand distortion, O incorporation, and amorphization of the MoN surface, without changes in roughness. Furthermore, with a controlled potential hold procedure, we show that the surface changes concurrent with potential conditioning are stable under ORR relevant potentials. Conversely, at higher potentials (≥0.8 V vs RHE), the film incorporates O, dissolves, and roughens, suggesting that in this higher potential regime, the performance enhancements are due to increased access to active sites. Density functional theory calculations and Pourbaix analysis provide insights into film stability and O incorporation as a function of potential. These findings coupled with in situ electrochemical surface-sensitive X-ray techniques demonstrate an approach to studying nontraditional surfaces in which we can leverage our understanding of surface dynamics to improve performance with the rational, in situ tuning of active sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Thermal conversion of unsolvated Mg(B3H8)2 to BH4- in the presence of MgH2

In the search for energy storage materials, metal octahydrotriborates, M(B3H8)n, n=1,2, are promising candidates but their synthesis suffers from residual solvents which tend to interact and greatly alter their decomposition mechanism. Therefore, we studied the thermal conversion of unsolvated Mg(B3H8)2 to BH4 -: as synthesized, and in the presence of MgH2. The conversion of our unsolvated Mg(B3H8)2 starts at ~100°C and yields ~22 wt% of BH4 - along with the formation of (closo-hydro)borates and volatile boranes. This loss of boron (B) is a sign of poor cyclability of the system. However, the addition of MgH2 to unsolvated Mg(B3H8)2 drastically increases the thermal conversion to 85-88wt% of BH4 - while simultaneously decreasing the amounts of B-losses. Our results strongly indicate that the presence of activated MgH2 substantially decreases the formation of (closohydro) borates and provides the necessary H2 for the B3H8-to-BH4 conversion. This is the first report of a metal octahydrotriborate system to selectively convert to BH4 - under moderate conditions of temperature (200°C) in less than 1h, making the MgB3H8-MgH2 system very promising for energy storage applications.

Gigante, Angelina↗
DOE OSTI2022

Atomically Dispersed CuN x Sites from Thermal Activation of Boron Imidazolate Cages for Electrocatalytic Methane Generation

Atomically dispersed metal sites (ADMSs) have been recognized as promising candidates for electrochemical conversion. Among a diverse range of molecular precursors for ADMS synthesis, framework materials are particularly interesting due to their high degree of tunability and control over the primary coordination sphere of the metal ions. In this work, we demonstrate that a copper boron imidazolate cage, BIF-29(Cu), is a convenient precursor for a competent catalyst with isolated Cu sites coordinated by N donors for carbon dioxide electroreduction (CO 2 RR). Although BIF-29(Cu) exhibited moderate methane selectivity over hydrogen evolution reaction (HER), the methane selectivity is significantly enhanced by 2 times (55% CH 4 at –1.25 V vs RHE) after mild thermal activation. Extensive characterization methods indicate the transformation of crystalline BIF-29(Cu) into an amorphous carbonaceous material comprising isolated CuN x sites. Moreover, in situ X-ray absorbance spectroscopy indicates stable CuN x sites that are reduced during CO 2 RR. This work encourages the discovery of single-site electrocatalytic systems through a rational selection of molecular precursor and calcination parameters for promoting product selectivity.

10 SYNTHETIC FUELS↗
DOE OSTI2024

Can a Coating Mitigate Molten Na Dendrite Growth in NaSICON Under High Current Density?

Alkali metals are among the most desirable negative electrodes for long duration energy storage due to their extremely high capacities. Currently, only high-temperature (>250 °C) batteries have successfully used alkali electrodes in commercial applications, due to limitations imposed by solid electrolytes, such as low conductivity at moderate temperatures and susceptibility to dendrites. Toward enabling the next generation of grid-scale, long duration batteries, we aim to develop molten sodium (Na) systems that operate with commercially attractive performance metrics including high current density (>100 mA cm –2 ), low temperature (<200 °C), and long discharge times (>12 h). In this work, we focus on the performance of NaSICON solid electrolytes in sodium symmetric cells at 110 °C. Specifically, we use a tin (Sn) coating on NaSICON to reduce interfacial resistance by a factor of 10, enabling molten Na symmetric cell operation with “discharge” durations up to 23 h at 100 mA cm –2 and 110 °C. Unidirectional galvanostatic testing shows a 70% overpotential reduction, and electrochemical impedance spectroscopy (EIS) highlights the reduction in interfacial resistance due to the Sn coating. Detailed scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) show that Sn-coated NaSICON enables current densities of up to 500 mA cm –2 at 110 °C by suppressing dendrite formation at the plating interface (Mode I). In conclusion, this analysis also provides a mechanistic understanding of dendrite formation at current densities up to 1000 mA cm –2 , highlighting the importance of effective coatings that will enable advanced battery technologies for long-term energy storage.

25 ENERGY STORAGE↗
DOE OSTI2024

Ramifications of X-Site Ion Modification in a Zero-Dimensional Piezoelectric Tetrahalozincate

Using mixtures of A, B, or X site ions in piezoelectric hybrid organic inorganic materials has been shown to be an effective strategy to improve piezoelectric properties. Here, we investigated the effect of increasing Br content within histammonium tetrachlorozincate [HistNH3Zn(Cl x Br 1–x )4] by varying the relative amounts of Cl and Br from x = 0% to 100% on nonlinear optical and piezoelectric properties. We found that the crystal structures were unchanged with Br percentages up to 100%, but the melting point of the materials changed substantially with increasing Br content. On the other hand, the nonlinear optical properties were only moderately affected with increasing Br content. The piezoelectric response of each material was measured and compared with DFT calculated values, both of which agreed that the overall the materials had relatively similar d 33 coefficients. The x = 75% Br compound had the largest magnitude d 33 value at maximum strain at both 29 °C (−97.56 pm/V) and 40 °C (−92.00 pm/V). The observed negative piezoelectric response is a rare trait that was ascribed to the large number of intermolecular interactions between lattice elements, as described by others.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Oxide-Encapsulated Ruthenium Oxide Catalysts for Selective Oxygen Evolution in Unbuffered pH-Neutral Seawater

Direct seawater electrolysis is a promising approach to producing green hydrogen in water-scarce environments using renewable energy. However, the undesirable chlorine evolution reaction and hypochlorite evolution reaction compete with the desired oxygen evolution reaction (OER) at the anode electrocatalyst. This issue is most pronounced in unbuffered pH-neutral solutions due to local acidification resulting from the OER. To overcome this challenge, this study provides a comprehensive evaluation of the use of silicon oxide (SiO x ) and titanium oxide (TiO x ) nanoscale overlayers coated on metallic ruthenium (Ru) and ruthenium oxide (RuO x ) thin film electrodes and their ability to block chloride ions from reaching active sites during operation in an unbuffered 0.6 M NaCl electrolyte. Using a combination of (electro)analytical techniques, encapsulated RuO x anodes are shown to effectively suppress Cl - transport to buried catalyst active sites while allowing for the desired OER to occur, leading to increases in OER faradaic efficiency at moderate overpotentials. Evidence for the ability of SiO x overlayers to block Cl - ions from reaching the active buried interface was obtained by monitoring the ν(O-H) stretching mode of OH adsorbates using in situ Raman spectroscopy. Here, this study also reports trade-offs between the activity, selectivity, and stability of bare and encapsulated Ru and RuO x electrocatalysts, finding that the magnitude of these trade-offs strongly depends on the complex interplay between electrode architecture, material properties, and catalytic performance, especially in unbuffered pH-neutral seawater.

58 GEOSCIENCES↗
DOE OSTI2024

Pathway to High Rate Capability in Interconnected Composite Electrolytes: A Case Study with a Single-Ion-Conducting Polymer

In a three-dimensional interconnected polymer/ceramic composite electrolyte (3D composite), both the polymer and ceramic electrolyte phases are individually connected with a polymer-rich surface layer to provide conformal contact with the electrodes. This work investigates how the transference number of the polymer phase affects the electrochemical properties of the 3D composite. Here, we fabricate a 3D composite using a “single-ion” conducting polymer electrolyte (PE), Li 1+x+y Al x Ti 2–x Si y P 3–y O 12 (LICGC) ceramic, and compare its electrochemical properties with the neat polymer, and with a 3D composite made with a dual-ion-conducting PE (we reported previously). Our results reveal that changing the polymer phase from a dual-ion-conducting PE to a single-ion-conducting PE results in a 9-fold increase in the limiting current density, although the interfacial impedance between the polymer and LICGC ceramic remains high (and contributes significantly to the total impedance of the 3D composite). Further, the limiting current density of the 3D composite is dictated by the PE and minimally affected by the ceramic scaffold. The ceramic scaffold, however, helps to ease the concentration gradient buildup within the PE and moderately improves the overall transference number. The LICGC scaffold does not provide any additional Li dendrite resistance due to its high reactivity with Li.

25 ENERGY STORAGE↗
DOE OSTI2024

Enhanced Anhydrous Proton Conductivity in Azole Phosphonic Acid Mixtures

Azole molecules are investigated as potential candidates for proton conductors under anhydrous conditions. Since 1,2,3-triazole has the lowest melting point (T m = 17 °C), it was blended with three phosphonic acid-containing molecules (small molecules with one and two phosphonic acids per molecule and a phosphonic acid polymer) to provide a source of excess protons to enhance the proton conductivity of the blends. Here we study a wide range of compositions in each system to find that these three mixtures show a maximum proton conductivity at moderate doping compositions, approximately 5–10 azole molecules per phosphonic acid group. Using NMR diffusometry, we show that the protons bonded to nitrogen move faster than the protons bonded to carbons of 1,2,3-triazole, suggesting proton hopping between azole proton carriers. Given the high proton conductivity at 90 °C of the best mixtures, in the range of 20–60 mS/cm, this work provides a path forward for future work in anhydrous proton-conducting polymer membranes. Additionally, Raman spectroscopy was used to accurately determine the molar percentage of protonated 1,2,3-triazole. Combining that with the proton diffusion results, we find that the phosphonic acid polymer shows the most proton hopping at low acid content.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗