Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “location map”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

GOES Satellite Observations for the FIRE/SRB Wisconsin Experiment Region from October 11 Through November 2, 1986

A map, concise tables, and satellite images are presented which show ground-site locations, GOES visible/infrared instrument counts above each site, and cloud spatial distribution for the experiment region from 11 October through 2 November 1986. The cloud images are presented near times of the afternoon NOAA-9 satellite overpasses in order to provide a qualitative aid in the interpretation of TOVS, AVHRR, and heat budget data during the FIRE/SRB experiment.

Whitlock, Charles H.↗

CO observations of L1582

In this paper, the bright-rimmed cloud L1582 is mapped in (C-12)O and (C-13)O, and the embedded NH3 core is mapped in the CS(3 - 2) line. The optical bright rim coincides with the cloud edge seen in CO. Both the kinetic temperature and column density maps show elongated features along the bright rim, and the NH3 core is located right near the edge of the cloud inside a column density plateau region corresponding to an optical extinction patch. The density enhancement in the CS core is about a factor of three over the ambient cloud and the core mass is estimated at eight solar. The dust luminosity can be supplied by radiation from the Gamma Ori OB association. The most plausible heating source for the cloud gas is the photoelectric ejection of energetic electrons from grains induced by the far-UV flux from the Gamma Ori OB association.

Zhou, Shudong↗

Impeller response calculation due to complex pressure loading

An analysis technique is described to calculate the harmonic response of the first-stage impeller of the Space Shuttle Main Engine high pressure fuel turbopump. The excitation is a complex pressure loading at various locations on the impeller blades. The pressure loading was predicted using computational fluid dynamic techniques and was given as a Fourier series at 48 different locations on each of the three impeller blade types. The analysis consisted of mapping the pressures onto a three-dimensional finite element model, then converting these pressure loads to complex nodal force vectors at specified equal time intervals. The resulting vectors were then converted to modal force time histories that were then transformed into the frequency domain where the frequency response was calculated directly. This technique resulted in an improvement to the previously used direct integration technique and in a substantial analysis cost reduction.

Wellstein, Carl↗

Discrete range clustering using Monte Carlo methods

For automatic obstacle avoidance guidance during rotorcraft low altitude flight, a reliable model of the nearby environment is needed. Such a model may be constructed by applying surface fitting techniques to the dense range map obtained by active sensing using radars. However, for covertness, passive sensing techniques using electro-optic sensors are desirable. As opposed to the dense range map obtained via active sensing, passive sensing algorithms produce reliable range at sparse locations, and therefore, surface fitting techniques to fill the gaps in the range measurement are not directly applicable. Both for automatic guidance and as a display for aiding the pilot, these discrete ranges need to be grouped into sets which correspond to objects in the nearby environment. The focus of this paper is on using Monte Carlo methods for clustering range points into meaningful groups. One of the aims of the paper is to explore whether simulated annealing methods offer significant advantage over the basic Monte Carlo method for this class of problems. We compare three different approaches and present application results of these algorithms to a laboratory image sequence and a helicopter flight sequence.

Chatterji, G. B.↗

Comparative mapping of Pluto's sub-Charon hemisphere - Three least squares models based on mutual event lightcurves

Observations of Charon transits are used here to derive preliminary maps of Pluto's sub-Charon hemisphere. Three models are used to describe the brightness of Pluto's surface as functions of latitude and longitude. Mapping results are presented using spherical harmonic functions, polynomial functions, and finite elements. A smoothing algorithm applied to the maps is described and the validity and resolution of the maps is tested by reconstruction from synthetic data. A preliminary finding from the maps is that the south polar region has the highest albedo of any location on the planet.

Young, Eliot F.↗

Time-Distance Helioseismology with the MDI Instrument: Initial Results

In time-distance helioseismology, the travel time of acoustic waves is measured between various points on the solar surface. To some approximation, the waves can be considered to follow ray paths that depend only on a mean solar model, with the curvature of the ray paths being caused by the increasing sound speed with depth below the surface. The travel time is effected by various inhomogeneities along the ray path, including flows, temperature inhomogeneities, and magnetic fields. By measuring a large number of times between different locations and using an inversion method, it is possible to construct 3-dimensional maps of the subsurface inhomogeneities. The SOI/MDI experiment on SOHO has several unique capabilities for time-distance helioseismology. The great stability of the images observed without benefit of an intervening atmosphere is quite striking. It his made it possible for us to detect the travel time fo separations of points as small as 2.4 Mm in the high-resolution mode of MDI (0.6 arc sec 1/pixel). This has enabled the detection of the supergranulation flow. Coupled with the inversion technique, we can now study the 3-dimensional evolution of the flows near the solar surface.

Duvall, T. L., Jr.↗

Differential Measurement Periodontal Structures Mapping System

This invention relates to a periodontal structure mapping system employing a dental handpiece containing first and second acoustic sensors for locating the Cemento-Enamel Junction (CEJ) and measuring the differential depth between the CEJ and the bottom of the periodontal pocket. Measurements are taken at multiple locations on each tooth of a patient, observed, analyzed by an optical analysis subsystem, and archived by a data storage system for subsequent study and comparison with previous and subsequent measurements. Ultrasonic transducers for the first and second acoustic sensors are contained within the handpiece and in connection with a control computer. Pressurized water is provided for the depth measurement sensor and a linearly movable probe sensor serves as the sensor for the CEJ finder. The linear movement of the CEJ sensor is obtained by a control computer actuated by the prober. In an alternate embodiment, the CEJ probe is an optical fiber sensor with appropriate analysis structure provided therefor.

Companion, John A.↗

Water Flow Performance of a Superscale Model of the Fastrac Liquid Oxygen Pump

As part of the National Aeronautics and Space Administration's ongoing effort to lower the cost of access to space, the Marshall Space Flight Center has developed a rocket engine with 60,000 pounds of thrust for use on the Reusable Launch Vehicle technology demonstrator slated for launch in 2000. This gas generator cycle engine, known as the Fastrac engine, uses liquid oxygen and RP-1 for propellants and includes single stage liquid oxygen and RP-1 pumps and a single stage supersonic turbine on a common shaft. The turbopump design effort included the first use and application of new suction capability prediction codes and three-dimensional blade generation codes in an attempt to reduce the turbomachinery design and certification costs typically associated with rocket engine development. To verify the pump's predicted cavitation performance, a water flow test of a superscale model of the Fastrac liquid oxygen pump was conducted to experimentally evaluate the liquid oxygen pump's performance at and around the design point. The water flow test article replicated the flow path of the Fastrac liquid oxygen pump in a 1.582x scale model, including scaled seal clearances for correct leakage flow at a model operating speed of 5000 revolutions per minute. Flow entered the 3-blade axial-flow inducer, transitioned to a shrouded, 6-blade radial impeller, and discharged into a vaneless radial diffuser and collection volute. The test article included approximately 50 total and static pressure measurement locations as well as flush-mounted, high frequency pressure transducers for complete mapping of the pressure environment. The primary objectives of the water flow test were to measure the steady-state and dynamic pressure environment of the liquid oxygen pump versus flow coefficient, suction specific speed, and back face leakage flow rate. Results showed excellent correlation between the predicted and experimentally measured pump head rise at low suction specific speeds. Likewise, only small circumferential variations in steady-state impeller exit and radial diffuser pressure distributions were observed from 80% to 120% of the design flow coefficient, matching the computational predictions and confirming that the integrated design approach has minimized any exit volute-induced distortions. The test article exhibited suction performance trends typically observed in inducer designs with virtually constant head rise with decreasing inlet pressure until complete pump head breakdown. Unfortunately, the net positive suction head at 3% head fall-off occurred far below that predicted at all tested flow coefficients, resulting in a negative net positive suction head margin at the design point in water. Additional testing to map the unsteady pressure environment was conducted and interesting rotating phenomena at the inducer inlet were observed. These rotating phenomena's cell numbers, direction, and speed were correlated with pump operating parameters. The impact of the unsteady phenomena and their corresponding energy losses on the unexpectedly poor pump performance is also discussed.

Skelley, Stephen↗

Trends in the Length of the Southern Ocean Sea Ice Season: 1979-1999

Satellite data can be used to observe the sea ice distribution around the continent of Antarctica on a daily basis and hence to determine how many days a year have sea ice at each location. This has been done for each of the 21 years 1979-1999. Mapping the trends in these data over the 21-year period reveals a detailed pattern of changes in the length of the sea ice season around Antarctica. Most of the Ross Sea ice cover has undergone a lengthening of the sea ice season, whereas most of the Amundsen Sea ice cover and almost the entire Bellingshausen Sea ice cover have undergone a shortening of the sea ice season. Results around the rest of the continent, including in the Weddell Sea, are more mixed, but overall, more of the Southern Ocean experienced a lengthening of the sea ice season than a shortening. For instance, the area experiencing a lengthening of the sea ice season by at least 1 day per year is 5.8 x 10(exp 6) sq km, whereas the area experiencing a shortening of the sea ice season by at least 1 day per year is less than half that, at 2.8 x 10(exp 6) sq km. This contrasts sharply with what is happened over the same period in the Arctic, where, overall, there has been some depletion of the ice cover, including shortened sea ice seasons and decreased ice extents.

Parkinson, Claire L.↗

Water Flow Performance of a Superscale Model of the Fastrac Liquid Oxygen Pump

As part of the National Aeronautics and Space Administration's ongoing effort to lower the cost of access to space, the Marshall Space Flight Center has developed a rocket engine with 60,000 pounds of thrust for use on the Reusable Launch Vehicle technology demonstrator slated for launch in 2000. This gas generator cycle engine, known as the Fastrac engine, uses liquid oxygen and RP-1 for propellants and includes single stage liquid oxygen and RP-1 pumps and a single stage supersonic turbine on a common shaft. The turbopump design effort included the first use and application of new suction capability prediction codes and three-dimensional blade generation codes in an attempt to reduce the turbomachinery design and certification costs typically associated with rocket engine development. To verify the pump's predicted cavitation performance, a water flow test of a superscale model of the Fastrac liquid oxygen pump was conducted to experimentally evaluate the liquid oxygen pump's performance at and around the design point. The water flow test article replicated the flow path of the Fastrac liquid oxygen pump in a 1.582x scale model, including scaled seal clearances for correct leakage flow at a model operating speed of 5000 revolutions per minute. Flow entered the 3-blade axial-flow inducer, transitioned to a shrouded, 6- blade radial impeller, and discharged into a vaneless radial diffuser and collection volute. The test article included approximately 50 total and static pressure measurement locations as well as flush-mounted, high frequency pressure transducers for complete mapping of the pressure environment. The primary objectives of the water flow test were to measure the steady-state and dynamic pressure environment of the liquid oxygen pump versus flow coefficient, suction specific speed, and back face leakage flow rate. Initial results showed acceptable correlation between the predicted and experimentally measured pump head rise at low suction specific speeds. Likewise, only small circumferential variations in steady-state were observed from 80% to 120% of the design flow coefficient, matching the computational predictions and confirming that the integrated design approach has minimized any exit volute-induced distortions. The test article exhibited suction performance trends typically observed in inducer designs with virtually constant head rise with decreasing inlet pressure until complete pump head breakdown. Unfortunately, the net positive suction head at 3% head fall-off occurred far below that predicted at all tested flow coefficients, resulting in a negative net positive suction head margin at the design point in water. Additional testing to map the unsteady pressure environment was conducted and cavitation-induced flow disturbances at the inducer inlet were observed. Two distinct disturbances were identified, one rotating and one stationary relative to the fixed frame of reference, while the transition from one regime to the next produced significant effects on the steady state pump performance. The impact of the unsteady phenomena and the corresponding energy losses on the unexpectedly poor pump performance is also discussed.

Skelley, Stephen↗

A Model for the Oxidation of Carbon Silicon Carbide Composite Structures

A mathematical theory and an accompanying numerical scheme have been developed for predicting the oxidation behavior of carbon silicon carbide (C/SiC) composite structures. The theory is derived from the mechanics of the flow of ideal gases through a porous solid. The result of the theoretical formulation is a set of two coupled nonlinear differential equations written in terms of the oxidant and oxide partial pressures. The differential equations are solved simultaneously to obtain the partial vapor pressures of the oxidant and oxides as a function of the spatial location and time. The local rate of carbon oxidation is determined using the map of the local oxidant partial vapor pressure along with the Arrhenius rate equation. The nonlinear differential equations are cast into matrix equations by applying the Bubnov-Galerkin weighted residual method, allowing for the solution of the differential equations numerically. The numerical method is demonstrated by utilizing the method to model the carbon oxidation and weight loss behavior of C/SiC specimens during thermogravimetric experiments. The numerical method is used to study the physics of carbon oxidation in carbon silicon carbide composites.

Sullivan, Roy M.↗

Analysis of Association Between Remotely Sensed (RS) Data and Soil Transmitted Helminthes Infection Using Geographical Information Systems (GIS): Boaco, Nicaragua

Soil-transmitted helminths are intestinal nematodes that can infect all members of a population but specially school-age children living in poverty. Infection can be significantly reversed with anthelmintic drug treatments and sanitation improvement. Implementation of effective public health programs requires reliable and updated information to identify areas at higher risk and to calculate amount of drug required. Geo-referenced in situ prevalence data will be overlaid over an ecological map derived from RS data using ARC Map 9.3 (ESRI). Prevalence data and RS data matching at the same geographical location will be analyzed for correlation and those variables from RS data that better correlate with prevalence will be included in a multivariate regression model. Temperature, vegetation, and distance to bodies of water will be inferred using data from Moderate-Resolution Imaging Spectroradiometer (MODIS) and Landsat TM and ETM+. Elevation will be estimated with data from The Shuttle Radar Topography Mission (SRTM). Prevalence and intensity of infections are determined by parasitological survey (Kato Katz) of children enrolled in rural schools in Boaco, Nicaragua, in the communities of El Roblar, Cumaica Norte, Malacatoya 1, and Malacatoya 2). This study will demonstrate the importance of an integrated GIS/RS approach to define sampling clusters without the need for any ground-based survey. Such information is invaluable to identify areas of high risk and to geographically target control programs that maximize cost-effectiveness and sanitation efforts.

MorenoMadrinan, Max J.↗

A Wrf-Chem Flash Rate Parameterization Scheme and LNO(x) Analysis of the 29-30 May 2012 Convective Event in Oklahoma During DC3

The Deep Convective Clouds and Chemistry (DC3) field campaign in 2012 provided a plethora of aircraft and ground-based observations (e.g., trace gases, lightning and radar) to study deep convective storms, their convective transport of trace gases, and associated lightning occurrence and production of nitrogen oxides (NOx). Based on the measurements taken of the 29-30 May 2012 Oklahoma thunderstorm, an analysis against a Weather Research and Forecasting Chemistry (WRF-Chem) model simulation of the same event at 3-km horizontal resolution was performed. One of the main objectives was to include various flash rate parameterization schemes (FRPSs) in the model and identify which scheme(s) best captured the flash rates observed by the National Lightning Detection Network (NLDN) and Oklahoma Lightning Mapping Array (LMA). The comparison indicates how well the schemes predicted the timing, location, and number of lightning flashes. The FRPSs implemented in the model were based on the simulated thunderstorms physical features, such as maximum vertical velocity, cloud top height, and updraft volume. Adjustment factors were added to each FRPS to best capture the observed flash trend and a sensitivity study was performed to compare the range in model-simulated lightning-generated nitrogen oxides (LNOx) generated by each FRPS over the storms lifetime. Based on the best FRPS, model-simulated LNOx was compared against aircraft measured NOx. The trace gas analysis, along with the increased detail in the model specification of the vertical distribution of lightning flashes as suggested by the LMA data, provide guidance in determining the scenario of NO production per intracloud and cloud-to-ground flash that best matches the NOx mixing ratios observed by the aircraft.

Cloud physics↗

In Situ Visible to Short Wavelength Imaging Spectroscopy with the Ultra Compact Imaging Spectrometer (UCIS): Case Studies from the Mars Exploration Rovers

In Situ imaging spectroscopy provides a way to address complex questions of geological evolution for both aqueous and igneous processes by mapping mineral composition at the spatial scale of rocks and outcrops. Examination of locations studied by the Mars Exploration Rovers Spirit and Opportunity can provide examples of the potential utility and define the needed measurement requirements. A compact instrument is needed to be able to adequately address these science questions from a rover platform. The Ultra Compact Imaging Spectrometer (UCIS) is an instrument designed to address the science need and implementation constraints.

mineralogy sampling↗

A WRF-Chem Flash Rate Parameterization Scheme and LNOx Analysis of the 29-30 May 2012 Convective Event in Oklahoma During DC3

The Deep Convective Clouds and Chemistry (DC3) field campaign in 2012 provided a plethora of aircraft and ground-based observations (e.g., trace gases, lightning and radar) to study deep convective storms, their convective transport of trace gases, and associated lightning occurrence and production of nitrogen oxides (NOx). Based on the measurements taken of the 29-30 May 2012 Oklahoma thunderstorm, an analysis against a Weather Research and Forecasting Chemistry (WRF-Chem) model simulation of the same event at 3-km horizontal resolution was performed. One of the main objectives was to include various flash rate parameterization schemes (FRPSs) in the model and identify which scheme(s) best captured the flash rates observed by the National Lightning Detection Network (NLDN) and Oklahoma Lightning Mapping Array (LMA). The comparison indicates how well the schemes predicted the timing, location, and number of lightning flashes. The FRPSs implemented in the model were based on the simulated thunderstorms physical features, such as maximum vertical velocity, cloud top height, and updraft volume. Adjustment factors were applied to each FRPS to best capture the observed flash trend and a sensitivity study was performed to compare the range in model-simulated lightning-generated nitrogen oxides (LNOx) generated by each FRPS over the storms lifetime. Based on the best FRPS, model-simulated LNOx was compared against aircraft measured NOx. The trace gas analysis, along with the increased detail in the model specification of the vertical distribution of lightning flashes as suggested by the LMA data, provide guidance in determining the scenario of NO production per intracloud and cloud-to-ground flash that best matches the NOx mixing ratios observed by the aircraft.

Atmospheric chemistry↗

Spectral Characterization of Analog Samples in Anticipation of OSIRIS-REx's Arrival at Bennu

NASA's Origins, Spectral Interpretation, Resource Identification, and Security-Regolith Explorer (OSIRIS-REx) mission successfully launched on September 8th, 2016. During its rendezvous with near-Earth asteroid (101955) Bennu beginning in 2018, OSIRIS-REx will characterize the asteroid's physical, mineralogical, and chemical properties in an effort to globally map the properties of Bennu, a primitive carbonaceous asteroid, and choose a sampling location [e.g. 1]. In preparation for these observations, we spectrally characterized a suite of analog samples across visible, near- and thermal-infrared wavelengths and used these in initial tests of phase detection and abundance determination software algorithms. Here we present the thermal infrared laboratory measurements of the analog sample suite measured under asteroidlike conditions, which are relevant to the interpretation of spectroscopic observations by the OSIRIS-REx Thermal Emission Spectrometer (OTES) [2, 3]. This suite of laboratory measurements of asteroid analogs under asteroid-like conditions is the first of their kind.

Donaldson Hanna, K. L.↗

Spectral Characterization of Analog Samples in Anticipation of OSIRIS-REx's Arrival at Bennu

NASA's Origins, Spectral Interpretation, Resource Identification, and Security-Regolith Explorer (OSIRIS-REx) mission successfully launched on September 8th, 2016. During its rendezvous with near-Earth asteroid (101955) Bennu beginning in 2018, OSIRIS-REx will characterize the asteroid's physical, mineralogical, and chemical properties in an effort to globally map the properties of Bennu, a primitive carbonaceous asteroid, and choose a sampling location]. In preparation for these observations, analog samples were spectrally characterized across visible, near- and thermal-infrared wavelengths and were used in initial tests on mineral-phase-detection and abundance-determination software algorithms.

Donaldson Hanna, K. L.↗

Aerosol Layer Height With Enhanced Spectral Coverage Achieved by Synergy Between VIIRS and OMPS-NM Measurements

This study presents a near production-ready algorithm to retrieve the height of biomass burning smoke and mineral dust aerosols as part of NASA’s Deep Blue aerosol data product suite. It utilizes the enhanced spectral coverage achieved by using co-located data from the Visible Infrared Imaging Radiometer Suite (VIIRS) and the Ozone Mapping and Profiler Suite Nadir Mapper (OMPS-NM), both aboard the Suomi National Polar-orbiting Partnership (S-NPP) satellite. Specifically, the 412 nm top-of-atmosphere reflectance from VIIRS and the ultraviolet aerosol index from OMPS-NM are used to determine the height and single-scattering albedo of the absorbing aerosols simultaneously. Constraints on aerosol optical depth at 550 nm and surface reflectance for the 412 nm band are provided by the operational VIIRS Deep Blue aerosol product. Wildfire smoke layer heights obtained from the algorithm over North America, where smoke plumes often stretched thousands of kilometers, are shown to agree with those from Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) measurements, with an uncertainty generally within 1-1.5 km. This new height data set will be included in the upcoming Version 2 VIIRS Deep Blue aerosol product.

Aerosol↗