Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interfacial energy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The role of interfacial donor–acceptor percolation in efficient and stable all-polymer solar cells

Polymerization of Y6-type acceptor molecules leads to bulk-heterojunction organic solar cells with both high power-conversion efficiency and device stability, but the underlying mechanism remains unclear. Here we show that the exciton recombination dynamics of polymerized Y6-type acceptors (Y6-PAs) strongly depends on the degree of aggregation. While the fast exciton recombination rate in aggregated Y6-PA competes with electron-hole separation at the donor–acceptor (D–A) interface, the much-suppressed exciton recombination rate in dispersed Y6-PA is sufficient to allow efficient free charge generation. Indeed, our experimental results and theoretical simulations reveal that Y6-PAs have larger miscibility with the donor polymer than Y6-type small molecular acceptors, leading to D–A percolation that effectively prevents the formation of Y6-PA aggregates at the interface. Besides enabling high charge generation efficiency, the interfacial D–A percolation also improves the thermodynamic stability of the blend morphology, as evident by the reduced device “burn-in” loss upon solar illumination.

14 SOLAR ENERGY↗
DOE OSTI2020

Atomic-scale constituting stable interface for improved LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathodes of lithium-ion batteries

Ascribed to their higher capacity and lower cost compared to conventional LiCoO 2 , the Ni-rich layered LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) is now considered as one promising cathode for lithium-ion batteries (LIBs). However, it still suffers from some evident performance degradation, especially under high cutoff voltages (i.e., >4.3 V versus Li/Li + ). The performance degradation typically is exhibited as capacity fading and voltage drop, mainly originating from an instable interface between the NMC622 and electrolyte as well as the evolution of the NMC structure. To improve the interfacial and structural stability of NMC cathodes, herein we deposited an ultrathin layer of Al 2 O 3 coatings (<5 nm) conformally over NMC622 composite electrodes directly using atomic layer deposition (ALD). It was found that, under different upper cutoff voltages (4.3, 4.5, and 4.7 V), the ALD Al 2 O 3 coatings enable enhanced performance of NMC622 cathodes with better cyclability and higher capacity. Particularly, the beneficial effects of the ALD Al 2 O 3 coatings are more remarkable at higher upper cutoff voltages (4.5 and 4.7 V). Furthermore, the ALD coatings can significantly improve the rate capability of NMC622. To this end, we utilized a suite of characterization tools and performed a series of electrochemical tests to clarify the effects of the ALD Al 2 O 3 coatings. This study revealed that the beneficial effects of the Al 2 O 3 ALD coatings are multiple: (i) serving as an artificial layer of solid electrolyte interphase to mitigate undesirable interfacial reactions; (ii) acting as a physical barrier to inhibit metal dissolution of NMC; and (iii) forming a reinforced networked overcoating to boost the mechanical integrity of NMC cathodes. This study is favorable for designing high-performance NMC cathodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Catalytic consequences of hydrogen addition events and solvent-adsorbate interactions during guaiacol-H 2 reactions at the H 2 O-Ru(0 0 0 1) interface

Catalytic reactions of biomass-derived phenolics and H 2 occur on transition metal surfaces via competitive C–O cleavage and ring saturation pathways, with both requiring multiple hydrogen addition events before forming their respective rate limiting transition states. These events are markedly affected by solvent chemical identity, with polar protic solvents ionizing hydrogen adatoms (H*) to interfacial protons (H + ) and opening up new catalytic routes. Here, we establish the reaction coordinate space for guaiacol-H 2 reactions on Ru(0 0 0 1) using density functional theory and describe the atomic-scale effect of a polar protic solvent, H 2 O. Coupled H + and H* attack leads to quasi-equilibrated enol and keto intermediates as the precursors for C–O cleavage and ring saturation, respectively. For C–O cleavage, H 2 O solvent enables a lower energy pathway via concomitant transfer of the hydroxyl H + to the methoxy oxygen during C–OCH 3 cleavage, forming a charge separated [Ru(s)–(C 6 H 5 O – )…(H + )…OCH 3 ] transition state and reducing the barrier by up to 0.8 eV as compared to unassisted C–OCH 3 cleavage. For ring saturation, H* attack onto an unsaturated meta carbon is rate limiting with no direct solvent participation, suggesting that protic polar solvents selectively promote the C–O cleavage pathway. Taken together, we show that activating guaiacol for either C–O bond cleavage or ring saturation product formation depends on the reactive hydrogen identity (H* or H + ), enol/keto isomerization equilibrium, and accessibility of the proton assisted Car–OCH 3 cleavage transition state. Here, all such factors are tunable via changes to the solvent or metal identity.

09 BIOMASS FUELS↗
DOE OSTI2021

Hydrophobic Molecule Monolayer Brush-Tethered Zinc Anodes for Aqueous Zinc Batteries

Aqueous zinc batteries are of great interest as a rechargeable energy storage system, particularly owing to the low cost and high safety of aqueous electrolytes, as well as the high capacity of zinc anodes. Unfortunately, the wide commercialization of aqueous zinc batteries is impeded by the irreversible water reduction and irregular zinc evolution issues on the anode side. Hereby, a hydrophobic and ultrathin polystyrene molecule brush layer is tethered onto the surface of zinc metal anodes to tackle the above limitations. Here, experimental investigations reveal that the waterproof artificial layer can sustain fast interfacial ionic transportation, minimize hydrogen evolution, and smoothen Zn deposition, thus conferring enhanced electrochemical performance to the as-protected Zn anode in both symmetric Zn//Zn cells and Zn//LiV 3 O 8 full cells.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Resolving the Electron Plume within a Scanning Electron Microscope

Scanning electron microscopy (SEM), a century-old technique, is today a ubiquitous method of imaging the surface of nanostructures. However, most SEM detectors simply count the number of secondary electrons from a material of interest, and thereby overlook the rich material information contained within them. Here, by simple modifications to a standard SEM tool, we resolve the momentum and energy information on secondary electrons by directly imaging the electron plume generated by the electron beam of the SEM. Leveraging these spectroscopic imaging capabilities, our technique is able to image lateral electric fields across a prototypical silicon p–n junctions and to distinguish differently doped regions, even when buried beyond depths typically accessible by SEM. Intriguingly, the subsurface sensitivity of this technique reveals unexpectedly strong surface band bending within nominally passivated semiconductor structures, providing useful insights for complex layered component designs, in which interfacial dynamics dictate device operation. Further, these capabilities for noninvasive, multimodal probing of complicated electronic components are crucial in today’s electronic manufacturing but is largely inaccessible even with sophisticated techniques. These results show that seemingly simple SEM can be extended to probe complex and useful material properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In Situ and Post-Mortem Characterizations of Ultrasonic Spot Welded AZ31B and Coated Dual Phase 590 Steel Joints

Ultrasonic spot welding using different welding conditions was applied to join dissimilar metals of galvanized DP590 steel and AZ31B magnesium sheets. In situ high-speed imaging, digital image correlation, and infrared thermography were utilized to quantitatively study the interfacial relative motion, surface indentation, and heat generation across the joint faying interface and the sheet/sonotrode interfaces under the welding condition of moderate welding power and short welding time. For welds made with high power and long welding time, lap shear tensile tests as well as fatigue tests were carried out. Different fracture modes were observed after the lap shear tensile tests and fatigue tests performed under different peak loads. Post-weld cross-sectional analysis with scanning electron microscopy coupled with energy dispersive X-Ray spectroscopy revealed the variation of morphology and chemical composition at the joint interface for welds made with different welding conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Giant Orbital Anisotropy with Strong Spin–Orbit Coupling Established at the Pseudomorphic Interface of the Co/Pd Superlattice

Orbital anisotropy at interfaces in magnetic heterostructures has been key to pioneering spin–orbit-related phenomena. However, modulating the interface’s electronic structure to make it abnormally asymmetric has been challenging because of lack of appropriate methods. Here, the authors report that low-energy proton irradiation achieves a strong level of inversion asymmetry and unusual strain at interfaces in [Co/Pd] superlattices through nondestructive, selective removal of oxygen from Co3O4/Pd superlattices during irradiation. Structural investigations corroborate that progressive reduction of Co3O4into Co establishes pseudomorphic growth with sharp interfaces and atypically large tensile stress. The normal component of orbital to spin magnetic moment at the interface is the largest among those observed in layered Co systems, which is associated with giant orbital anisotropy theoretically confirmed, and resulting very large interfacial magnetic anisotropy is observed. All results attribute not only to giant orbital anisotropy but to enhanced interfacial spin–orbit coupling owing to the pseudomorphic nature at the interface. They are strongly supported by the observation of reversal of polarity of temperature-dependent Anomalous Hall signal, a signature of Berry phase. This work suggests that establishing both giant orbital anisotropy and strong spin–orbit coupling at the interface is key to exploring spintronic devices with new functionalities.

42 ENGINEERING↗
DOE OSTI2026

Toward durable stacks: glass-ceramic sealants for intermediate-temperature protonic ceramic electrochemical systems

Protonic ceramic electrochemical cells (PCECs) are emerging as promising technologies for efficient energy conversion and hydrogen production because they operate at intermediate temperatures with improved efficiency and durability compared with conventional solid oxide electrochemical cells. However, the long-term reliability and commercialization of PCEC stacks remain strongly limited by the performance of sealants, which are required to maintain gas tightness, electrical insulation, and mechanical integrity under harsh thermal and chemical environments. Among various sealing approaches, glass-ceramic sealants are considered the most practical and scalable due to their excellent wettability, chemical tunability, and strong interfacial adhesion. This review provides a comprehensive overview of recent advances in glass-ceramic sealants for intermediate-temperature protonic ceramic electrochemical systems. The fundamental design principles of sealant compositions are first discussed, followed by recent developments in deposition methods, sintering strategies, surface treatments, and degradation monitoring techniques. Particular attention is given to the unique challenges associated with PCEC operating conditions, including hydrothermal degradation, interfacial reactions with barium-containing electrolytes, and thermal mismatch. Finally, future opportunities involving sustainable materials, multiscale modeling, additive manufacturing, and artificial intelligence-assisted sealant optimization are highlighted.

glass–ceramic sealants↗
DOE OSTI2020

Functional Nanomaterials with Tunable Plasmonic and Emittive Properties (Final Project Report)

The goal of the project is on understanding the principles of non-covalent assembling of tunable functional materials with various nanocrystals in order to control light-matter interactions by changing localized interfacial refractive properties, coupling parameters, or the ionic environment of surrounding media. We explore novel soft functional matrices with controlled physical properties via the application of light, mechanical stresses, ionic environment, and electrical potential. These functional matrices is used in conjunction with novel anisotropic inorganic nanostructures such as noble metal/metal alloy anisotropic nanostructures with complex optical properties (multiple LSPR modes) and quantum dots with light-emissive or absorbing properties in a broad spectral range from the UV to the NIR for efficient solar energy absorption and light conversion.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Functionalization of Cathode–Electrolyte Interface with Ionic Liquids for High-Performance Quasi-Solid-State Lithium–Sulfur Batteries: A Low-Sulfur Loading Study

We introduce a quasi-solid-state electrolyte lithium-sulfur (Li–S) battery (QSSEB) based on a novel Li-argyrodite solid-state electrolyte (SSE), Super P–Sulfur cathode, and Li-anode. The cathode was prepared using a water-based carboxymethyl cellulose (CMC) solution and styrene butadiene rubber (SBR) as the binder while Li6PS5F0.5Cl0.5 SSE was synthesized using a solvent-based process, via the introduction of LiF into the argyrodite crystal structure, which enhances both the ionic conductivity and interface-stabilizing properties of the SSE. Ionic liquids (IL) were prepared using lithium bis(trifluoromethyl sulfonyl)imide (LiTFSI) as the salt, with pre-mixed pyrrolidinium bis(trifluoromethyl sulfonyl)imide (PYR) as solvent and 1,3-dioxolane (DOL) as diluent, and they were used to wet the SSE–electrode interfaces. The effect of IL dilution, the co-solvent amount, the LiTFSI concentration, the C rate at which the batteries are tested and the effect of the introduction of SSE in the cathode, were systematically studied and optimized to develop a QSSEB with higher capacity retention and cyclability. Interfacial reactions occurring at the cathode–SSE interface during cycling were also investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and X-ray photoelectron spectroscopy supported by ab initio molecular dynamics simulations. This work offers a new insight into the intimate interfacial contacts between the SSE and carbon–sulfur cathodes, which are critical for improving the electrochemical performance of quasi-solid-state lithium–sulfur batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Thermodynamics of Tritium Trapping by Point Defects at Interfacial Cr-based Phases of the Al Coating

Density functional theory (DFT) simulations have been carried out to evaluate the potential for tritium trapping by metal vacancies in four phases Cr-containing phases (i.e., Cr3Si, Al0.3Cr0.7, Al8Cr5-HT, and Al8Cr5) identified near the interface between the Al coating and 316 stainless steel (316 SS) cladding. In addition, an ab initio thermodynamics approach has been employed to predict the temperature and T2-partial pressure dependence on the thermodynamics of singly tritiated defects. Key results in this work suggest that metal vacancies in the four phases have the potential to favorably trap tritium species, especially Si vacancies in Cr3Si phase. This overall thermodynamic trend can be correlated to the energy cost of having an interstitial tritium in the lattice, which has been calculated to range from 0.17 eV in Al8Cr5-HT to 0.89 eV in Cr3Si. A comparison of the results from this study with previous theoretical works investigating tritium behavior in other Fe-Al phases identified in the aluminide coating, suggests that metal vacancies are generally able to trap tritium in various Fe-Al aluminide phases. Especially, it was found that Si and Al vacancies would be the most efficient to trap for tritium, followed by Cr vacancies, then Fe and Ni vacancies. In the four Cr-based material phases investigated in this work, it is interesting to note that, in the absences of Fe or Ni species, strong interactions between tritium and the metal vacancies are always occurring by the formation of preferential Cr—T bonds (i.e., no Si—T or Al—T bonds were formed).

Sassi, Michel J.↗
DOE OSTI2024

Catalytic Reaction Triggered by Magnetic Induction Heating Mechanistically Distinguishes Itself from the Standard Thermal Reaction

As a recent advancement in chemical engineering, magnetic induction heating (MIH) is utilized to initiate the intended reactions by enabling the self-heating of the ferromagnetic catalyst particles. While MIH can be energy-efficient and industrially scalable, its full potential has been underappreciated in catalysis because of the perception that MIH is merely an alternative heating approach. Unexpectedly, we show that the MIH-triggered reaction could go beyond standard thermal catalysis. Specifically, by probing the representative Pt/Fe 3 O 4 catalysts with CO oxidation in both thermal and MIH modes with consistent temperature profiles and catalyst structures, we found that the MIH mode boosts the reactivity more than 25 times by modifying Pt-FeO x interfacial synergies and promoting facile oxidation of the adsorbed carbonyl species by atomic oxygen. Further, as we preliminarily observed, this beneficial MIH-catalysis can be translational to other thermal reactions, potentially paving the way to launch MIH-catalysis as a distinct reaction category.

CO oxidation↗
DOE OSTI2025

Modulating physicochemical interfaces enables li-rich oxides based ceramic solid-state li batteries under ambient conditions

Li-rich layered oxides exhibit promising potential applications in high-energy-density solid-state lithium metal batteries. Nevertheless, the strong oxidative oxygen species generate at high voltage, which poses great challenges to positive electrode-side interface stability. Herein, a robust in-situ polymerization gel polymer electrolyte with bifunctional additives is designed for interface modification. These additives, include lithium difluoro(oxalate) borate and LiPO 2 F 2 , regulate the Li + chemical environment in gel polymer electrolyte to enhance crosslink density without residual oligomer, which reduce gas generation and suppress contact loss, thus avoiding interfacial impedance divergence. Concurrently, the designed gel polymer electrolyte enables a wide electrochemical stability window (up to 4.7 V) and a high Li + transference number (0.82). Additionally, the additives induced F- and B-rich inorganic cathode-electrolyte interphase inhibits side reactions and oxygen/transition metal loss effectively, stabilizing the chemical interface. The as-constructed Li-rich layered oxides-based ceramic solid-state lithium metal batteries with gel polymer electrolyte interface modification exert a high discharge capacity of 276.5 mAh g -1 at 30 °C without external pressure, delivering a retention of 81.7% after 100 cycles at 25 mA g -1 during 2.0-4.7 V. This work provides a guideline for developing high-voltage solid-state lithium metal batteries via interfacial design.

Hu, Xinchao [Xiamen University (China)]↗
DOE OSTI2023

MEMPHIS (Mesoscle Multiphysics Phase Field Simulator v.0

SAND2024-01427O Mesoscale Multiphysics Phase Field Simulator (MEMPHIS) is used for solving interfacial problems and can be applied to many evolutionary problems. Some examples are solidification dynamics, viscous fingering, fracture mechanics, hydrogen embrittlement, vesicle dynamics, electro-mechanical degradation of batteries, aging of microstructures, and segregation. MEMPHIS is written in Fortran 90 in a modular fashion, where model and numerical solvers are decoupled from one another. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

Dingreville, Remi↗
DOE OSTI2025

Visualizing diverse lithium growth and stripping behaviors in anode-free solid-state batteries with operando X-ray tomography

Anode-free solid-state batteries (SSBs), which eliminate the need for lithium metal use during cell assembly, have the potential to enable high energy densities and simplified manufacturing. However, the factors that control lithium growth/stripping at the anode current collector are not well understood. Here, we use operando X-ray microcomputed tomography to comprehensively image and quantify lithium deposition and stripping under various conditions in three different Li|Li 6 PS 5 Cl|current collector cells, revealing diverse behavior that depends on interface morphology, cell resistance, and solid-state electrolyte (SSE) microstructure. A cell with high resistance exhibits extensive lithium filament growth across the entire current collector interface, with filaments that grow around pre-existing pores in the SSE rather than lithium filling these pores. Lithium filament formation is partially reversible, with the cracks shrinking as lithium metal is stripped. Uniform lithium deposition is achievable at low current densities in low-resistance cells, whereas higher current densities in these cells cause an increase in interfacial roughness, which is correlated with subsequent filamentary growth at the edges of the cell. These results provide insight into filamentary vs. planar lithium growth and highlight that the evolution of lithium is sensitively dependent on SSE microstructure and electrochemical processes.

25 ENERGY STORAGE↗
DOE OSTI2025

Resistive Switching in SrFeO2.5/Nb:SrTiO3 Heterostructures with Growth-Controlled Film Orientation

Resistive switching, a behavior found in many oxide materials, has the potential to enable emerging computer hardware technologies and architectures. We present resistive switching devices fabricated from epitaxial brownmillerite SrFeO2.5 films with two distinct film orientations, wherein facile oxygen ion diffusion planes are aligned parallel (in-plane) and perpendicular (out-of-plane) with the electrodes. SrFeO2.5 films were grown on (001) oriented Nb:SrTiO3 to enable high-quality interfaces and future integration with Si CMOS technologies. Post-growth vacuum annealing and growth pressure were used to control film orientations, as confirmed by transmission electron microscopy and x-ray diffraction measurements. Films grown with diffusion planes oriented in-plane had oxygen-rich, perovskite-like nanodomains spread throughout the film, and fabricated devices exhibited worse switching consistency and more stochasticity. In contrast, films grown with diffusion planes oriented out-of-plane had a more uniform oxygen-rich perovskite interfacial layer above the bottom electrode, and devices built from this film orientation showed significant statistical improvements in switching voltages and cycling consistency.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

C60-Based Ionic Salt Electron Shuttle for High-Performance Inverted Perovskite Solar Modules

Although C60 is usually the electron transport layer (ETL) in inverted perovskite solar cells, its molecular nature of C60 leads to weak interfaces that lead to non-ideal interfacial electronic and mechanical degradation. Here, we synthesized an ionic salt from C60, 4-(1',5'-dihydro-1'-methyl-2'H-[5,6] fullereno-C60-Ih-[1,9-c]pyrrol-2'-yl) phenylmethanaminium chloride (CPMAC), and used it as the electron shuttle in inverted PSCs. The CH2-NH3+ head group in the CPMA cation improved the ETL interface and the ionic nature enhanced the packing, leading to ~3-fold increase in the interfacial toughness compared to C60. Using CPMAC, we obtained ~26% power conversion efficiencies (PCEs) with ~2% degradation after 2,100 hours of 1-sun operation at 65degrees C. For minimodules (four subcells, 6 centimeters square), we achieved the PCE of ~23% with <9% degradation after 2,200 hours of operation at 55degrees C.

14 SOLAR ENERGY↗
DOE OSTI2021

Enhancing Steam-Side Heat Transfer via Microdroplet Ejection using Inorganic Coatings

During condensation of water on a superhydrophobic nanostructured surfaces, droplets coalesce and jump (droplet ejection) due to the release of excess surface energy. Meticulously designed nanostructured surfaces or coatings capable of droplet ejection can enhance heat transfer performance by easy removal of droplets during condensation. In the present work, the capabilities of the Nelumbo droplet ejection coatings technology currently used in commercial heat exchangers are explored and optimized for materials and conditions relevant to steam condensers. Specifically, this includes (1) adapting and optimizing the procedures and chemistries to deposit droplet ejecting coatings on materials used in the steam condenser, (2) testing of the heat transfer, durability, and fouling of the fabricated coatings under a variety of steam condenser relevant conditions, and (3) modeling of the impact of droplet dynamics and interfacial properties on heat transfer in steam condensers. We experimentally demonstrated that at low supersaturation conditions (S~1.02), developed superhydrophobic nanostructured surface gives a 40% higher peak heat transfer flux and a 17% higher peak overall heat transfer coefficient (U) with droplet ejection mechanism compared to the dropwise condensation mechanism on the same nanostructured surface. Though the experimentally observed droplet ejection mechanism was short-lived (~3 min) due to the limitation of the chiller to maintain a constant supersaturation condition in fabricated steam condenser. And large variations in water inlet temperature (+ to - 2 degrees C) caused flooding of nanostructure (Wenzel state) at higher supersaturation (S > or = 1.12). This is an important finding because typical supersaturation levels in field operation are over 1.8 and as such, either the flooding potential for these materials should be improved or operation at lower supersaturation may be required to maximize heat transfer efficiency. If supersaturation conditions can be maintained reliably in the steam condenser in addition to droplet ejection mechanism during condensation, this could provide a potential 2% reduction in water flow rate which equates to a savings of over 3900 gallons of water per minute for a 500 MW steam turbine and over $0.3MM savings annually given a 0.02 cent marginal water withdrawal cost. It is also worth noting that these savings are based on improvement of droplet ejection coatings over coatings capable of performing consistent dropwise mechanism in in-field surface condensers. Savings due to the droplet ejections coatings when compared to bare substrates could be much higher. Additionally, the present work provides the importance of steam condenser operating conditions and insights into the challenges in modeling the condensing droplet dynamics on surfaces.

20 FOSSIL-FUELED POWER PLANTS↗