Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graphitization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Fiber optic strain measurements in filament-wound graphite-epoxy tubes containing embedded fibers

Filament-wound graphite-epoxy tubes fabricated with embedded fiber optic sensors were tested at NASA Langley Research Center to evaluate the feasibility of monitoring stress with a fiber optic technique. Resistance strain gauges were attached to the tubes to measure strain at four locations along the tubes. Both static and dynamic strain measurements were made with an excellent agreement between the embedded fiber optic strain sensor and the strain gauges. The results indicate that fiber optic sensors embedded in composites may be useful as the sensing component of smart structures.

Rogowski, R. S.↗
NASA NTRS1989

Scaling effects in the impact response of graphite-epoxy composite beams

In support of crashworthiness studies on composite airframes and substructure, an experimental and analytical study was conducted to characterize size effects in the large deflection response of scale model graphite-epoxy beams subjected to impact. Scale model beams of 1/2, 2/3, 3/4, 5/6, and full scale were constructed of four different laminate stacking sequences including unidirectional, angle ply, cross ply, and quasi-isotropic. The beam specimens were subjected to eccentric axial impact loads which were scaled to provide homologous beam responses. Comparisons of the load and strain time histories between the scale model beams and the prototype should verify the scale law and demonstrate the use of scale model testing for determining impact behavior of composite structures. The nonlinear structural analysis finite element program DYCAST (DYnamic Crash Analysis of STructures) was used to model the beam response. DYCAST analysis predictions of beam strain response are compared to experimental data and the results are presented.

Jackson, Karen E.↗
NASA NTRS1989

Effect of heat-treatment temperature of vapor-grown graphite fibers. I - Properties of their bromine intercalation compounds

Vapor-grown graphite fibers were heat treated at 2000, 2200, 2400, 2600, 2800, and 3000 C, brominated at room temperature for two days, and then characterized by X-ray diffraction analysis, differential scanning calorimetry, and resistivity measurements. Fibers greater than 13 microns in diameter had low resistivities (50 microohms or less) irrespective of the heat treatment temperature. An analysis of the results obtained suggests that resistivities below 6 microohms cannot be achieved through a further reduction in defect level unless the amount of bromine is increased.

Gaier, James R.↗
NASA NTRS1989

Correlation of the deply technique with ultrasonic imaging of impact damage in graphite-epoxy composites

The ultrasonic quantitative NDE of graphite-epoxy composites is difficult because of the inherent inhomogeneity of the material. An examination technique must discriminate between inherent scattering centers in an undamaged region and the scattering centers due to defects or damage. Two NDE techniques that can make this distinction were used to image and quantify the extent of damage resulting from a low-energy impact. These results were then compared with those from a destructive technique. The first NDE technique, polar backscatter, employed a nonzero polar angle insonifying method to reduce specular reflection from the surface of the sample; the second NDE technique used a normal-incidence ultrasonic beam. Results from both NDE methods were subsequently correlated with those from a destructive technique, the deply method. Both the qualitative and quantitative agreement of the methods was excellent.

Smith, B. T.↗
NASA NTRS1989

Buckling and postbuckling behavior of square compression-loaded graphite-epoxy plates with circular cutouts

The postbuckling behavior of square compression-loaded graphite-epoxy plates and isotropic plates with a central circular cutout is studied. The results suggest that the change in the plate's axial stiffness is strongly dependent on cutout size and plate orthotropy. It is found that the cutout size and stacking sequence of a composite plate may be tailored to optimize postbuckling stiffness. Also, it is suggested that a cutout may influence model interaction in a plate. The effects of load-path eccentricity on buckling behavior are examined.

Nemeth, Michael P.↗
NASA NTRS1990

Thermal effects on fiber optic strain sensors embedded in graphite-epoxy composites

Smart structures deployed in low earth orbit will be exposed to a hostile environment which will include temperature extremes during each orbit as the platform moves from the day to the night side. The stresses due to thermal cycling may compromise the performance of embedded fiber optic strain sensors because of differential thermal expansion of the fiber and the composite material. The effects of elevated temperature and thermal cycling on the performance of a fiber optic strain sensor embedded in a graphite-epoxy tube have been investigated for temperatures from 65 to 220 F. The results indicate that the fiber optic strain sensor measurements correlate well with conventional resistance strain gages attached to the tube.

Rogowski, R. S.↗
NASA NTRS1990

Matrix toughness, long-term behavior, and damage tolerance of notched graphite fiber-reinforced composite materials

The long-term behavior of notched graphite-fiber-reinforced composite laminates with brittle or tough matrix materials and different fiber architectures was investigated using damage measurements and stiffness change, residual strength, and life data. The fiber/matrix materials included T300/5208, AS4/3501-6, AS4/1808, AS4/PEEK, and C3000/PMR-15 matrices and unidirectional tape and woven cloth fiber architectures. Results of damage evaluation and of residual strength measurements during the fatigue damage development showed that the long-term behavior and damage tolerance are controlled by a number of interacting factors such as the matrix toughness, fiber architecture, loading levels, and damage types and distributions.

Bakis, C. E.↗
NASA NTRS1991

Apparatus For Chemically Treating Graphite Fibers

New apparatus for chemical treatment of graphite-fiber tow developed. Applies chemical solutions to commercially purchased unsized fibers or in-house-made fibers, to improve following: handling of fibers, interface bonding of fiber to resin matrix during prepreg fabrication, and interface bonding in laminates during molding process. Designed for research and development, with predrying and post-drying in inert environments. Easily adaptable to different chemical solutions and well suited for small-scale, prototype, tailor-made fiber systems. Used to develop fiber/resin composites for aerospace, automotive, marine, and other applications.

Stanfield, Clarence E.↗
NASA NTRS1991

Analysis of matrix cracking and local delamination in (0/theta/-theta)sub s graphite epoxy laminates under tension load

Several 3D finite element analyses of (0/theta/-theta)sub s graphite epoxy laminates, where theta=15, 20, 25, 30, and 45 deg, subjected to axial tension load were performed. The interlaminar stresses in the theta/-theta interface were calculated with and without a matrix crack in the central -theta plies. The interlaminar normal stress changes from a small compressive stress when no matrix crack is present to a high tensile stress at the intersection of the matrix crack and free edge. The analysis of local delamination from the -theta matrix crack indicates a high strain energy release rate and a localized mode I component near the free edge, within one ply distance from the matrix crack. In order to examine the stress state causing the matrix cracking the maximum principal normal stress in a plane perpendicular to the fiber direction in the -theta ply was calculated in an uncracked laminate. The corresponding shear stress parallel to the fiber was also calculated. The principal normal stress at the laminate edge increases through the ply thickness and reached a very high tensile value at the theta/-theta interface indicating that the crack in the -theta ply may initiate at the theta/-theta interface. Crack profiles on the laminate edge in the -theta ply were constructed from the principal stress directions. The cracks were found to be more curved for layups with smaller theta angles, which is consistent with experimental observations in the literature.

Salpekar, S. A.↗
NASA NTRS1991

Thermal emittance enhancement of graphite-copper composites for high temperature space based radiators

Graphite-copper composites are candidate materials for space based radiators. The thermal emittance of this material, however, is a factor of two lower than the desired emittance for these systems of greater than or equal to 0.85. Arc texturing was investigated as a surface modification technique for enhancing the emittance of the composite. Since the outer surface of the composite is copper, and samples of the composite could not be readily obtained for testing, copper was used for optimization testing. Samples were exposed to various frequencies and currents of arcs during texturing. Emittances near the desired goal were achieved at frequencies less than 500 Hz. Arc current did not appear to play a major role under 15 amps. Particulate carbon was observed on the surface, and was easily removed by vibration and handling. In order to determine morphology adherence, ultrasonic cleaning was used to remove the loosely adherent material. This reduced the emittance significantly. Emittance was found to increase with increasing frequency for the cleaned samples up to 500 Hz. The highest emittance achieved on these samples over the temperature range of interest was 0.5 to 0.6, which is approximately a factor of 25 increase over the untextured copper emittance.

Rutledge, Sharon K.↗
NASA NTRS1989

A study of graphite-epoxy laminate failures due to high transverse shear strains using the multi-span-beam shear test procedure

The multi-span-beam shear test procedure is used to study failure mechanisms in graphite-epoxy laminates due to high transverse shear strains induced by severe local bending deformations in test specimens. Results of a series of tests on specimens with a variety of stacking sequences, including some with adhesive interleaving, are presented. These results indicate that laminates with stacking sequences with several + or - 45 and 90 deg plies next to each other are more susceptible to failures due to high transverse shear strains than laminates with + or - 45 and 0 deg plies next to each other or with + or - 45 deg plies next to layers of adhesive interleaving. Results of these tests are compared with analytical results based on finite elements.

Jegley, Dawn C.↗
NASA NTRS1990

Temperature-dependent tensile and shear response of P100/6061 graphite-aluminum

This paper summarizes the results of an investigation conducted to characterize tensile and shear response of P100/6061 graphite-aluminum composite in the temperature range -101 to 260 C. The off-axis tension test and Iosipescu shear test methods were employed to meet this objective. The experimental results indicate that both the fiber-dominated and matrix-dominated elastic properties exhibit relatively small changes in the considered temperature range. The effect of temperature on yielding and strength, however, is significant under longitudinal and shear loading. Residual stresses play a significant role in controlling the variation of the yield stress with temperature. The observed low transverse strength of the composite is explained by interfacial defects between adjacent precursor wires induced during fabrication.

Fujita, Takahiro↗
NASA NTRS1990

Static and dynamic response of graphite-epoxy curved frames

Experiments were conducted to measure the three-dimensional static and vibratory response of two graphite-epoxy, thin-walled, open section frames. The frames are semicircular with a radius of three feet. One specimen had an I cross section and the other had a channel cross section. The experimental data is used to evaluate a mixed finite element model of the frames that is based on Vlasov-type, thin-walled, open section curved beam theory.

Collins, J. S.↗
NASA NTRS1991

Postbuckling response and failure prediction of flat rectangular graphite-epoxy plates loaded in axial compression

The objectives of the study are to assess the capability of a first-order shear deformable degenerated shell finite element theory to predict the postbuckling response and failure modes of various graphite-epoxy panels loaded in axial compression. Two panels without holes and one with a hole are studied, and the resulting responses and failure modes correlated well with the experimental results. A progressive damage failure mechanism is applied in the nonlinear analysis, which proved successful in predictions of failure location, mode, and load.

Engelstad, S. P.↗
NASA NTRS1991

Scale effects in buckling, postbuckling and crippling of graphite-epoxy Z-section stiffeners

The buckling, postbuckling and crippling of Hercules Inc. AS4/3502 graphite-epoxy Z-section stiffeners is investigated as a function of specimen structural parameters. Variables addressed are flange and web widths, flange-to-web corner radius, thickness and stacking sequence. Analytical, numerical and experimental results are discussed. Nondimensional parameters have been obtained from an analytical model which effectively normalize the initial local buckling data reported herein and in the references. The nature of the load redistribution after buckling and its impact on postbuckling stiffness is related to the geometric variables. A normalized total width concept is used to unify the crippling data.

Wieland, Todd M.↗
NASA NTRS1991

Nonlinear static and dynamic finite element analysis of an eccentrically loaded graphite-epoxy beam

The Dynamic Crash Analysis of Structures (DYCAT) and NIKE3D nonlinear finite element codes were used to model the static and implulsive response of an eccentrically loaded graphite-epoxy beam. A 48-ply unidirectional composite beam was tested under an eccentric axial compressive load until failure. This loading configuration was chosen to highlight the capabilities of two finite element codes for modeling a highly nonlinear, large deflection structural problem which has an exact solution. These codes are currently used to perform dynamic analyses of aircraft structures under impact loads to study crashworthiness and energy absorbing capabilities. Both beam and plate element models were developed to compare with the experimental data using the DYCAST and NIKE3D codes.

Fasanella, Edwin L.↗
NASA NTRS1991

Thermal emittance enhancement of graphite-copper composites for high temperature space based radiators

Graphite-copper composites are candidate materials for space based radiators. The thermal emittance of this material, however, is a factor of two lower than the desired emittance for these systems of greater than or equal to 0.85. Arc texturing was investigated as a surface modification technique for enhancing the emittance of the composite. Since the outer surface of the composite is copper, and samples of the composite could not be readily obtained for testing, copper was used for optimization testing. Samples were exposed to various frequencies and currents of arcs during texturing. Emittances near the desired goal were achieved at frequencies less than 500 Hz. Arc current did not appear to play a major role under 15 amps. Particulate carbon was observed on the surface, and was easily removed by vibration and handling. In order to determine morphology adherence, ultrasonic cleaning was used to remove the loosely adherent material. This reduced the emittance significantly. Emittance was found to increase with increasing frequency for the cleaned samples up to 500 Hz. The highest emittance achieved on these samples over the temperature range of interest was 0.5 to 0.6, which is approximately a factor of 25 increase over the untextured copper emittance.

Rutledge, Sharon K.↗
NASA NTRS1990

Ultrasonic nondestructive evaluation of graphite epoxy composite laminates

Quantitative ultrasonic techniques are summarized with applications to the measurement of frequency-dependent attenuation and backscatter and to the NDE of composite laminates. Results are listed for the ultrasonic NDE of graphite-epoxy composite laminates including impact and fatigue damage as well as porosity. The methods reviewed include transmission measurements of attenuation, reconstructive tomography based on attenuation, estimating attenuation from backscattered ultrasound, and backscatter approaches. Phase-sensitive and -insensitive detection techniques are mentioned such as phase cancellation at piezoelectric receiving transducers and acoustoelectric effects. The techniques permit the NDE of the parameters listed in inhomogeneous media and provide both images from the transmission mode and in the reflection mode.

Miller, James G.↗