Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “geoscience”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Geophysical monitoring using active seismic techniques at the Citronelle Alabama CO 2 storage demonstration site

Between August 2012 and September 2014, about 114,000 metric tonnes of CO 2 was captured from the coal-fired Plant Barry Power Station at Bucks Alabama and injected into the Paluxy Formation above the oil pool in the southeast unit of the Citronelle Oilfield. Various monitoring methods were deployed at land surface and in project wells to measure system performance, comply with permit requirements and test new and innovative monitoring tools. The monitoring program relied heavily on active seismic methods for subsurface imaging of geologic structure and time-lapse seismic techniques to track the CO 2 migration in the injection interval. Both conventional geophone/hydrophone and fiber-optic based Distributed Acoustic Sensing (DAS) arrays were deployed and tested, allowing a side by side comparison of the equipment and techniques. Geophysical imaging of the subsurface was successful using DAS in the offset vertical seismic profile (OVSP) survey configuration. A high resolution OVSP image of the subsurface was obtained in 2014 with DAS, which exceeded project expectations in comparison to a lower resolution image obtained in 2012 using a conventional 80-level geophone array. A time-lapse image of the redistribution of CO 2 after injection ended in September 2014 was obtained with two DAS OVSP surveys from June 2014 and December 2015, thus successfully demonstrating its proof-of-concept. Unfortunately, a pre-injection baseline survey with DAS, which was in its initial stage of technology development in 2012, did not have sufficient quality for use, making it difficult to interpret the acquired DAS time-lapse difference. Additional research in this area has since demonstrated the utility of time-lapse DAS OVSP. DAS data were also acquired during a cross-well seismic survey conducted in 2014. Unfortunately, the DAS technique was not success in the cross-well survey configuration because the system noise level was too high in the crosswell frequency output range (100–1200 Hz) of the piezoelectric source (increasing by a factor of ten compared to VSP frequency band). Additionally, the cross-well geometry causes sub-horizontal (broadside) incidence on the vertical DAS fiber cable, which is known to be problematic. Current research is focused on improving the DAS cable response to broadside acoustic energy. Time-lapse seismic surveys using commercially available conventional arrays were also acquired. In contrast to the DAS acquired data, the cross-well seismic results obtained with the conventional array was highly successful and clearly showed the CO 2 remained in zone at the end of injection. Time-lapse differencing of the OSVP surveys acquired with the conventional arrays proved to be inconclusive. Finally, changes in wellbore conditions between surveys and unavoidable changes in equipment (the array used for the baseline survey was retired) affected data quality, making it difficult to interpret the OVSP results.

58 GEOSCIENCES↗
DOE OSTI2020

Wellbore injectivity response to step-rate CO 2 injection: Coupled thermo-poro-elastic analysis in a vertically heterogeneous formation

Safe and permanent carbon geological storages require an elaborate analysis of geomechanical stability. Subsurface injection of CO 2 changes the local temperature and pore pressure and, further, alters the stress due to thermo-poro-elastic responses. A permanent CO 2 storage testing was conducted in the water leg of Cranfield reservoir in Mississippi, USA, where hosted CO 2 enhanced-oil recovery activities. During CO 2 injection, the injection rate was ramped up twice but the bottom-hole pressure did not increase with the imposed injection rates as expected. This unexpected field observation suggests the possibility of an open-mode fracture development at the injector. However, the injector response and potential fracture development have not been rigorously interpreted with detailed near-wellbore temperature and pore pressure change upon the CO 2 injection. In this study, we performed history matching of CO 2 injection using coupled thermo-poro-elastic reservoir simulation to examine the possibility of fracturing. We built a reservoir model including vertical heterogeneity in both petrophysical and geomechanical properties estimated from well-logging analysis and laboratory experiments. The simulation results show that CO 2 injection changes stresses and support the hypothesis of development of an open-mode fracture at the injector during the Cranfield test. The near-injector region exhibits a large temperature reduction up to 55 °C with ensuing effective horizontal stress reduction up to 9.1 MPa. However, a caprock integrity issue is unlikely because of the horizontal stress contrast within layers and low hydraulic communication with the injection zone. This work indicates that the injectant temperature should be considered in the design of high-rate CO 2 injector.

58 GEOSCIENCES↗
DOE OSTI2020

Influence of geochemical reactions on the creep behavior of Mt. Simon sandstone

The capture and subsurface storage of carbon dioxide is a sustainable option that is currently pursued worldwide to mitigate greenhouse gas effect. However, predicting the long-term mechanical integrity of CO 2 underground storage systems remains a challenge. To address that question, it is essential to understand the influence of fluid-rock chemo-mechanical interactions on the long-term and on the time-dependent mechanical properties. In turn, the long-term mechanical response and the time-dependent mechanical behavior can be represented by the creep response. We investigate the impact of CO 2 -induced geochemical reaction on the creep response of Mt. Simon sandstone with a 50–400 micron grain size. We perform static and dynamic flow experiments on Mt. Simon sandstone specimens under geological conditions, at a temperature of T = 50 - 53 °C and for CO 2 pressures of P = 8:62; 17:2 MPa under both static flow and dynamic flow-through conditions. After aging, we employ creep indentation testing, high-resolution SEM-EDS, computer vision, machine learning, and micromechanics modeling to probe changes on the microstructure and mechanical properties. Following both static and dynamic flow-through experiments, we observe a 10–22% decrease in quartz volume fraction and an increase in both the microporosity (7–28%) and nanoporosity (60–65%). Additional CO 2 -induced microstructural changes include an enlargement of pore throats and the formation of channels. These observations point to the presence of CO 2 -induced K-feldspar dissolution and clay dissolution reactions. Here, the macroscopic creep behavior is logarithmic and the macroscopic creep modulus varies depending on the microporosity and the relative quartz and feldspar content. As a result of these geochemical reactions and of the related microstructural changes, a 55-60% decrease in the macroscopic logarithmic creep modulus is predicted.

58 GEOSCIENCES↗
DOE OSTI2020

Normal or abnormal? Machine learning for the leakage detection in carbon sequestration projects using pressure field data

The international commitments for atmospheric carbon reduction will require a rapid increase in carbon capture and storage (CCS) projects. The key to any successful CCS project lies in the long term storage and prevention of leakage of stored carbon dioxide (CO 2 ). In addition to being a greenhouse gas, CO 2 leaks reaching the surface can accumulate in low-lying areas resulting in a serious health risk. Among several alternatives, some of the more promising CCS storage formations are depleted oil and gas reservoirs, where the reservoirs had good geological seals prior to hydrocarbon extraction. With more CCS wells coming online, it is imperative to implement permanent, automated monitoring tools. We apply machine learning models to automate the leakage detection process in carbon storage reservoirs using rates of (CO 2 ) injection and pressure data measured by simple harmonic pulse testing (HPT). To validate the feasibility of this machine learning based workflow, we use data from HPT experiments carried out in the Cranfield oil field, Mississippi, USA. The data consist of a series of pulse tests conducted with baseline parameters and with an artificially introduced leak. Here, in this study, we pose the leakage detection task as an anomaly detection problem where deviation from the predicted behavior indicates leaks in the reservoir. Results show that different machine learning architectures such as multi-layer feed forward network, Long Short-Term Memory, and convolutional neural network are able to identify leakages and can provide early warning. These warnings can then be used to take remedial measures.

58 GEOSCIENCES↗
DOE OSTI2021

Inference of Rock Flow and Mechanical Properties from Injection-Induced Microseismic Events During Geologic CO 2 Storage

Monitoring microseismic activities during CO 2 injection into geologic formations is important for ensuring the safety of the storage operations. The resulting data provide insight into the response of the storage formation to CO 2 injection and can be used to infer the underlying rock flow and mechanical properties. In this paper, assimilation of microseismic data is performed for dynamic characterization of the storage formation by using a stochastic simulation model to forecast the microseismic response of a geologic formation during CO 2 injection. Two modeling approaches are adopted to predict the space-time distribution of the injection-induced microseismicity. The first model is based on pore pressure relaxation assumption, while the second model uses coupled flow and geomechanics simulation to establish the complex physical relation between the storage formation properties and the corresponding microseismic responses during CO 2 injection. The stochastic predictive models in each case are used in ensemble data assimilation frameworks to estimate rock properties from the observed microseismic data. Two data assimilation methods are considered: (i) a new ensemble-based stochastic point process filter (EnPPF) that can directly integrate discrete microseismic events, and (ii) a variant of ensemble smoother, known as the ensemble smoother with multiple data assimilation (ES-MDA), which requires continuous representation of microseismic events for assimilation. The two methods are successfully applied to a geologically realistic model of the Farnsworth Field in Texas, with complex geologic flow units and interacting fault systems.

42 ENGINEERING↗
DOE OSTI2020

Tracking natural CO 2 migration through a sandstone aquifer using Sr, U and C isotopes: Chimayó, New Mexico, USA

The geochemical and isotopic characteristics of groundwaters in Chimayó, New Mexico, reflect processes that affect water quality in the Tesuque Aquifer, which overlies a leaking natural CO 2 source in a structurally complex region. In this study, select isotopes (δ 13 C, 87 Sr/ 86 Sr, 234 U/ 238 U) are applied to groundwaters to better understand CO 2 transport mechanisms and related water-rock interactions that impact Chimayó groundwater. Carbon stable isotope ratios of dissolved inorganic carbon (DIC; δ 13 CDIC = -15.10‰ to 4.50‰) identify a distinct source of upward-migrating CO 2 that interacts with the groundwater. Additionally, groundwater 87 Sr/ 86 Sr compositions (0.7098 to 0.7154) reflect intrusion of varying amounts of saline water associated with the high CO 2 source, while 234 U/ 238 U ratios corroborate presence of deep groundwater and suggest impacts from distinctive natural uranium sources are affecting groundwater. Previous work proposed two CO 2 transport mechanisms at the site: (1) dissolved in deep brine that underlies the aquifer and (2) in the gas phase; this study uses isotope mixing models to identify wells that are affected by these CO 2 transport mechanisms and demonstrates that both transport mechanisms are associated with impaired groundwaters. Overall, this study demonstrates that applying multiple isotope systems (δ 13 CDIC, 87 Sr/ 86 Sr, 234 U/ 238 U) is a dynamic tool for identifying and measuring the impact of CO 2 leakage from a sequestration site.

58 GEOSCIENCES↗
DOE OSTI2021

A screening model for predicting injection well pressure buildup and plume extent in CO 2 geologic storage projects

We present a new screening model for predicting injection well pressure buildup and CO 2 plume migration for CO 2 geologic sequestration projects. The model requires only limited information and is quite accurate when compared to detailed simulation results. Such models can assist project developers during the early days of project planning (e.g., for 45Q related projects), and also help regulators perform simple checks against detailed numerical models. The screening model consists of two correlations: one for injectivity index in terms of the slope of the CO 2 fractional flow curve, and the second for total storage efficiency within the footprint of plume as a function of gravity number and slope of the CO 2 fractional flow curve. Using these two correlations, as well as a knowledge of some basic reservoir characteristics and estimates of fluid properties from standard correlations, the injection-well pressure buildup and CO 2 plume extent in the formation can be readily estimated. Finally, the new correlations show a good match with the results of the underlying simulations, and also provide good agreement with independent calculations for two example problems.

42 ENGINEERING↗
DOE OSTI2021

Effect of CO 2 -brine-rock reactions on pore architecture and permeability in dolostone: Implications for CO 2 storage and EOR

Geologic carbon sequestration (GCS) is considered a feasible technology for storing substantive volumes of greenhouse gases in subsurface geological formations. In the reservoir, far from carbon dioxide (CO 2 ) injection wells or in post-injection scenarios, diffusion dominates over advection. This condition conjoins with spatially distributed geochemical reactions to induce heterogeneous changes in pore architecture, i.e. pore body and throat sizes or surface roughness. These changes can affect CO 2 transport properties and storage capacity. In this work, we investigated mineral dissolution and precipitation in dolomite samples saturated with a CO 2 -saturated brine at 93 °C and 34.5 MPa, aged without flow. Two rock types samples, i.e. intergranular- and vuggy-dominant, were selected to investigate changes in pore size, porosity and permeability under reactive conditions. Mineral dissolution and precipitation were characterized using scanning electron microscopy. Changes in pore size were quantified via time-domain nuclear magnetic resonance (TD-NMR) transverse relaxation time (T 2 ) and diffusion coefficient (D) distributions. We show that mineral dissolution likely occurs in highly permeable pathways. These observations are confirmed through analysis of (T 2 ) and diffusion coefficient (D) distributions. In contrast to results during CO 2 -enriched brine continuous injection, mineral precipitation was observed in micropores. The leftward shift of the T 2 peaks, corresponding to micropores, also evidenced mineral precipitation in lowpermeability zones. However, microscale alterations resulted only in a subtle increase in porosity and permeability. Results in this study shed light on effects of geochemical reactions on alteration of rock properties in diffusion-dominated regions during CO 2 storage.

58 GEOSCIENCES↗
DOE OSTI2021

An automated system for continuous monitoring of CO 2 geosequestration using multi-well offset VSP with permanent seismic sources and receivers: Stage 3 of the CO2CRC Otway Project

Time-lapse seismic is an essential tool for monitoring CO 2 injection into the subsurface but suffers from high cost and long intervals between surveys. An alternative approach is continuous monitoring using permanent sources and receivers capable of mapping CO 2 plume evolution on an almost daily basis and drastically reduce human effort, cost and survey turnaround. As part of the CO2CRC Otway project, a continuous monitoring system is employed to monitor a small (15,000 tonnes) CO 2 injection within the CO2CRC Otway Project. The permanent monitoring system employs distributed acoustic sensors (DAS) installed in boreholes as seismic receivers and seismic orbital vibrators (SOV) as seismic sources. The monitoring approach is based on vertical seismic profiling using five wells equipped with DAS cemented behind the casing and nine SOVs and is acquiring the data continuously in an autonomous manner. The data is then automatically processed on-site producing a seismic image every 2.5 days, which is then transmitted to a remote office. The data has good repeatability with NRMS of about ~10-15%.

58 GEOSCIENCES↗
DOE OSTI2021

Skin factor and potential formation damage from chemical and mechanical processes in a naturally fractured carbonate aquifer with implications to CO 2 sequestration

Here, in this study, we investigate formation damage due to acidization and water injection tests into the naturally fractured carbonate Middle Duperow Formation at Kevin Dome, Montana, potentially diminishing the chance of a future successful Geological Carbon Sequestration (GCS) project. Multiple well-test analytical models, correlated with core description and lithology data, are used to determine flow behavior and communication between the water injection interval and surrounding formations. An improved three-dimensional (3D) geologic model with dual-continuum matrix and fracture properties is constructed based on most recent seismic, core, and water sample measurements. Brine injection is simulated to verify the interpretation from the analytical models, followed by CO 2 injection simulation. Geochemical calculations are performed to understand the in-situ processes that led to formation damage. Our findings suggest: (1) there are two possible scenarios that could lead to a positive total effective skin factor and permeability decline: partial penetration and formation damage; (2) analytical models indicate a positive total skin factor, contradicting results of a previous study suggesting that the well was mildly stimulated; (3) numerical simulation supports the formation damage hypothesis by matching the pressure buildup observed during the latter two brine injection tests; (4) several mechanical and chemical processes may have occurred during injection to clog the matrix/fracture system: anhydrite fines migration and/or calcite precipitation. We then make preventative suggestions for future GCS projects into carbonate reservoirs and remediation recommendations for GCS operation at the Kevin Dome.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

A coupled thermo-hydro-mechanical model for simulating leakoff-dominated hydraulic fracturing with application to geologic carbon storage

A potential risk of injecting CO2 into storage reservoirs with marginal permeability (≲ 10 mD (1 mD = 10 –15 m 2 )) is that commercial injection rates could induce fracturing of the reservoir and/or the caprock. Such fracturing is essentially fluid-driven fracturing in the leakoff-dominated regime. Recent studies suggested that fracturing, if contained within the lower portion of the caprock complex, could substantially improve the injectivity without compromising the overall seal integrity. Modeling this phenomenon entails complex coupled interactions among the fluids, the fracture, the reservoir, and the caprock. Here, we develop a simple method to capture all these interplays in high fidelity by sequentially coupling a hydraulic fracturing module with a coupled thermal-hydrological-mechanical (THM) model for nonisothermal multiphase flow. The model was made numerically tractable by taking advantage of self-stabilizing features of leakoff-dominated fracturing. The model is validated against the PKN solution in the leakoff-dominated regime. Moreover, we employ the model to study thermo-poromechanical responses of a fluid-driven fracture in a field-scale carbon storage reservoir that is loosely based on the In Salah project's Krechba reservoir. The model reveals complex yet intriguing behaviors of the reservoir-caprock-fluid system with fracturing induced by cold CO 2 injection. We also study the effects of the in situ stress contrast between the reservoir and caprock and thermal contraction on the vertical containment of the fracture. The proposed model proves effective in simulating practical problems on length and time scales relevant to geological carbon storage.

58 GEOSCIENCES↗
DOE OSTI2021

Efficient marine environmental characterisation to support monitoring of geological CO 2 storage

Carbon capture and storage is key for mitigating greenhouse gas emissions, and offshore geological formations provide vast CO 2 storage potential. Monitoring of sub-seabed CO 2 storage sites requires that anomalies signifying a loss of containment be detected, and if attributed to storage, quantified and their impact assessed. However, monitoring at or above the seabed is only useful if one can reliably differentiate abnormal signals from natural variability. Baseline acquisition is the default option for describing the natural state, however we argue that a comprehensive baseline assessment is likely expensive and time-bound, given the multi-decadal nature of CCS operations and the dynamic heterogeneity of the marine environment. We present an outline of the elements comprising an efficient marine environmental baseline to support offshore monitoring. We demonstrate that many of these elements can be derived from pre-existing and ongoing sources, not necessarily related to CCS project development. We argue that a sufficient baseline can be achieved by identifying key emergent properties of the system rather than assembling an extensive description of the physical, chemical and biological states. Further, that contemporary comparisons between impacted and non-impacted sites are likely to be as valuable as before and after comparisons. Furthermore, as these emergent properties may be nuanced between sites and seasons and comparative studies need to be validated by the careful choice of reference site, a site-specific understanding of the scales of heterogeneity will be an invaluable component of a baseline.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

A workflow to assess the efficacy of brine extraction for managing injection-induced seismicity potential using data from a CO 2 injection site near Decatur, Illinois

Injection of CO 2 for storage in a geologic formation increases pore pressure and alters in situ stresses. Depending on the orientation of any existing fault and fracture planes, such as critically stressed planes, this stress alteration will modify normal stresses acting on planes and could result in frictional sliding and release stored energy in the form of seismicity. Brine extraction (BE) is a technique that can be applied prior to, or during, CO 2 injection to reduce pore pressure for increasing storage capacity and, potentially, for reducing the likelihood of frictional sliding. Here a workflow is described to assess the efficacy of BE for mitigating frictional sliding (i.e., seismicity) during injection and entails: site characterization, stress calculations and failure assessment, static and dynamic modeling, and BE operational planning. Site characterization describes the stress field used to calculate the Coulomb Failure Function (CFF) that constrains allowable pore pressure changes and injection rates in the numerical simulation of CO 2 injection scenarios. The inclusion of BE in the workflow allows for determination of the potential need for pressure reduction, and evaluation of the effectiveness of this operation. Example application of the workflow using an injection field dataset near Decatur, IL, provides insight on fracture planes and stresses at the site, formation properties and the impact of variable CO 2 injection-rate targets on whether BE plans are required. The study workflow indicates that BE could enhance CO 2 injection rate by 39% and correspondingly reduce the potential for injection-induced seismicity as indicated by a reduction in CFF.

58 GEOSCIENCES↗
DOE OSTI2021

Seismic monitoring of a small CO 2 injection using a multi-well DAS array: Operations and initial results of Stage 3 of the CO 2 CRC Otway project

Active time-lapse seismic is widely employed for monitoring CO 2 geosequestration due to its ability to track the distribution of fluids in space and time. However, standard 4D seismic monitoring suffers from several challenges, including high cost, disruption to other land uses, and, consequently, relatively large intervals between monitor surveys. Some of these challenges can be mitigated using permanently installed sources and receivers. Such an approach was tested at the CO 2 CRC Otway site by continuous offset VSP monitoring of 15,000 t of supercritical CO 2 injected into an aquifer 1,500 m deep with nine permanent seismic sources (surface orbital vibrators or SOVs) and five downhole fibre-optic receivers. This continuous monitoring is complemented by multi-well 4D VSP using a mobile vibroseis source and the same DAS receivers, which included one baseline and two monitor surveys after injection of 4,000 and 12,000 t of CO 2 . The continuous DAS-SOV monitoring detected an abrupt increase of travel times below the injection interval on the second day of injection (after injection of 300 t of CO 2 ) and tracked the growth of the areal CO 2 plume by mapping changes of reflection amplitudes. The plume is also detected by time-lapse changes of reflection amplitudes in multi-well 4D VSPs. The plume images obtained from continuous offset VSP and 4D VSP are broadly consistent with each other but with some differences due to differences in illumination, lateral variations of velocities and seismic anisotropy. Furthermore, these differences also serve as a measure of uncertainty of 4D VSP images.

4D VSP↗
DOE OSTI2021

Impact of reservoir parameters and wellbore permeability uncertainties on CO 2 and brine leakage potential at the Shenhua CO 2 Storage Site, China

Here, this paper describes a system-level risk assessment for the Shenhua CO 2 storage site, China, using the National Risk Assessment Partnership Integrated Assessment Model for Carbon Storage (NRAP-IAM-CS). Here, we begin by determining the optimal number of Monte Carlo (MC) simulations to achieve CO 2 and brine leakage result convergence. Then, we calculate mass CO 2 and brine leakage to the atmosphere and a hypothetical shallow aquifer. Finally, we assess the geochemical impacts in the event of leakage as if there were a shallow freshwater aquifer at the Shenhua site. Simulation results show that leakage results tend to stabilize after 300 Monte Carlo simulations. When the three wells on site are assigned a permeability of 10 -11 m 2 (representing significantly leaking wells), moderate CO 2 and brine leakages occur, and the percentage of CO 2 leakage exceeds the threshold value we set based on the Intergovernmental Panel on Climate Change (IPCC). This is, however, unlikely to be the case for the Shenhua site. For all the other scenarios, the CO 2 leakage is trivial although there is still the possibility of CO 2 leakage into the groundwater aquifer exceeding the 1% threshold over 1000 years, assuming constant legacy wellbore permeability. For the significantly leaking scenario, there is a 10% probability to have a moderate (2.7 × 10 7 m 3 ) leakage-affected volume in the shallow aquifer with the pH below 6.5, and a large (1.4 × 10 8 m 3 ) volume with the total dissolved solids (TDS) above 500 ppm, hence pH and TDS may be considered for site monitoring plans. Based on the simulation results, there is a very low probability of significant CO 2 /brine leakage through the existing wells at the Shenhua CO 2 storage site.

58 GEOSCIENCES↗
DOE OSTI2021

Field-scale fault reactivation experiments by fluid injection highlight aseismic leakage in caprock analogs: Implications for CO 2 sequestration

Observations on tens-of-meter scale experiments of fault activation by fluid injection conducted in shales allow exploring how aseismic and seismic events may jeopardize the integrity of a sealing caprock overlying a CO 2 sequestration reservoir. We contrast the behavior of shale faults with another set of experiments conducted in carbonates. Significant fluid leakage occurs along the initially low-permeability shale faults when rupture is activated. Most of the leakage pathway closes when fluid injection ceases and fluid pressure drops. Dilatant slip on the fault plane alone does not explain the observed leakage behavior, which is also caused by fault opening favored by the softness of the shale, and by the structure of the fault zone that prevents fluids from diffusing into the adjacent damage zone. Experiments show a large amount of aseismic deformation. Small-magnitude seismicity (M w < -2.5) is observed outside the pressurized leakage patch. Stress transferred from this aseismic deformation patch can build up to stress-criticality and favor seismicity. Thus, in terms of fault activation in caprocks, aseismic fault slip leading to increased permeability and a loss of seal integrity is of great concern.

58 GEOSCIENCES↗
DOE OSTI2021

A Review of Well Integrity Based on Field Experience at Carbon Utilization and Storage Sites

Maintaining well integrity is critical to the success of geologic carbon storage (GCS) and carbon dioxide enhanced oil recovery (CO 2 -EOR) operations. Wells that experience leakage because of integrity issues can potentially become a risk to the environment or human health if they release previously captured CO 2 back into the atmosphere or into freshwater aquifers. There are many GCS and CO 2 -EOR sites in operation around the world. However, well integrity experiences at these sites are not widely documented in the public domain. This study details findings from a survey of well integrity experiences elicited from operators of GCS and CO 2 -EOR sites. The goal of the survey was to obtain information about site characteristics and operator experiences with well integrity, monitoring methods, and risk assessment of legacy wells. Literature relevant to the survey questions was also reviewed and summarized to provide context for survey responses and identify areas where field experiences with well integrity do and do not align with the current state of research. We highlight the current state-of-practice, identify research needs, and provide context for future interactions between researchers, operators, and regulators on issues related to well integrity.

54 ENVIRONMENTAL SCIENCES↗