Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “construction type”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Thermally stable structural framework

Development of structural framework with zero or negligible thermal expansion is discussed. Combination of two types of metallic materials in binary trellis to compensate for thermal expansion is explained. Construction details are presented and illustration is included.

Schuerch, H. U.↗

Fatigue experience from tests carried out with forged beam and frame structures in the development of the Saab aircraft Viggen

A part of the lower side of the main wing at the joint of the main spar with the fuselage frame was investigated. This wing beam area was simulated by a test specimen consisting of a spar boom of AZ 74 forging (7075 aluminum alloy modified with 0.3 percent Ag) and a portion of a honeycomb sandwich panel attached to the boom flange with steel bolts. The cross section was reduced to half scale. However, the flange thickness, the panel height, and the bolt size were full scale. Further, left and right portions of the fuselage frame intended to carry over the bending moment of the main wing were tested. Each of these frame halves consisted of a forward and a rear forging (7079 aluminum alloy, overaged) connected by an outer and inner skin (Alclad 7075) creating a box beam. These test specimens were full scale and were constructed principally of ordinary aircraft components. The test load spectrum was common to both types of specimens with regard to percentage levels. It consisted of maneuver and gust loads, touchdown loads, and loads due to ground roughness. A load history of 200 hours of flight with 15,000 load cycles was punched on a tape. The loads were randomized in groups according to the flight-by-flight principle. The highest positive load level was 90 percent of limit load and the largest negative load was -27 percent. A total of 20 load levels were used. Both types of specimens were provided with strain gages and had a nominal stress of about 300 MN/sq m in some local areas. As a result of the tests, steps were taken to reduce the risk of fatigue damage in aircraft. Thus stress levels were lowered, radii were increased, and demands on surface finish were sharpened.

Larsson, S. E.↗

A recalibration of the absolute magnitudes of supergiants.

Since luminosities of the supergiants are obtained most accurately by the group membership method, the study employed distance moduli of stellar groups that were determined from the magnitudes of the B-type main sequence stars using an extinction ratio of 3.0. For the supergiants, this ratio was taken to be a function of the spectral type following Schmidt-Kaler (1965) and Lee (1970). Supergiant data used in the construction of mean absolute magnitudes are discussed. In contrast to previous calibrations, no significant trend of visual absolute magnitude within a spectral subclass was found for the supergiants. Significant differences in some MK classes were observed between the results presented and the results of Blaauw and Schmidt-Kaler.

Stothers, R.↗

High performance S-band horn antennas for radiometer use

Horn antennas of four types: pyramidal corrugated, conical corrugated, pyramidal dual mode and conical dual mode, have been constructed and evaluated for use as S-band radiometer antennas. Each of the structures is described and radiation patterns and impedance and resistive loss measurements including a layer of foreign material on a thin radome, are presented. A precision method for determining reflection losses is described using a multiprobe reflectometer technique. The same technique is also applied to the measurement of resistive losses by closing the ends of the antennas with short circuit plates and determining the losses from an accurate measurement of the reflection coefficient. The radiation patterns were recorded with the aid of a real-time digital computer. The stored patterns were then processed to yield gain and beam efficiency. It was concluded that it is possible to design a highly efficient antenna for radiometer use and to measure its parameters precisely. However, it was found that it is necessary to modify the conventional definition of beamwidth somewhat if this term is to be meaningful for radiometer applications.

Caldecott, R.↗

Inexpensive high vacuum feedthroughs.

Description of the use of rigid coaxial cable in the construction of high vacuum coaxial and coaxial push-pull rotary motion feedthroughs. This type of feedthroughs is shown to be extremely cheap and simple to make and modify. It can be used for moderately high voltages and provides a continuous, well shielded, low-noise feedthrough cable in any desired configuration.

Gerber, S.↗

The manufacture of flat conductor cable

The major techniques are described for fabricating flat conductor cable (FCC). Various types of FCC, including unshielded, shielded, power, and signal, in both existing and conceptual constructions, are covered.

Angele, W.↗

SAM 2 balloon test (stratospheric aerosol measurement)

As a parallel effort to the LACATE balloon experiment a small optical system was constructed to enable a balloon test of a diode filter system similar to the type planned for the Nimbus-G SAM II experiment. The system was called the SAM II Balloon Test. Results of the balloon flight are summarized.

Pepin, T. J.↗

Remote sensing as an aid to community development in an arid area

High-altitude color infrared photography of a 70,000 acre site north of Tucson, Ariz., has been used to construct maps for land-use planning. Remote sensing data on land use, soil type, vegetation type, ground water recharge areas, and slope were categorized and digitized. Individual categories were assigned ranks indicating their suitability for urban development. Maps of individual characteristics were weighted according to their importance in a given land-use decision, and composite maps indicating good, average, and poor locations for a given type of development were plotted. These composite maps were found to be in good agreement with ground truth results.

Foster, K. E.↗

An investigation of accelerating mode and decelerating mode constant-momentum mass spectrometry and their application to a residual gas analyzer

A theoretical analysis of constant momentum mass spectrometry was made. A maximum resolving power for the decelerating mode constant momentum mass spectrometer was shown theoretically to exist for a beam of ions of known energy. A vacuum system and an electron beam ionization source was constructed. Supporting electronics for a residual gas analyzer were built. Experimental investigations of various types of accelerating and decelerating impulsive modes of a constant momentum mass spectrometer as applied to a residual gas analyzer were made. The data indicate that the resolving power for the decelerating mode is comparable to that of the accelerating mode.

Ng, Y. S.↗

Real-time and accelerated outdoor endurance testing of solar cells

Real-time and accelerated outdoor endurance testing was performed on a variety of samples of interest to the National Photovoltaic Conversion Program. The real-time tests were performed at seven different sites and the accelerated tests were performed at one of those sites in the southwestern United States. The purpose of the tests were to help evaluate the lifetime of photovoltaic systems. Three types of samples were tested; transmission samples of possible cover materials, sub-modules constructed using these materials attached to solar cells, and solar cell modules produced by the manufacturers for the ERDA program. Results indicate that suitable cover materials are glass, FEP-A and PFA. Dirt accumulation and cleanability are important factors in the selection of solar cell module covers and encapsulants.

Forestieri, A. F.↗

Volcanic features of Io

The various volcanic landforms observed on Io by Voyager 1 are described and compared with similar features on earth. Ionian calderas, observed to cover 5% of the surface, are generally found to be of low relief, similar to certain terrestrial calderas. Flow patterns observed include dark, linear markings with lobate margins resembling terrestrial lava flows, bright lobate markings originating at calderas, and a bright flow feature surrounding the calderas. Positive relief features associated with volcanic structures include pancake-like constructions similar to low volcanic cones, sheet-like structures, rugged mountains, and a type of surface upheaval. Bright and dark diffuse markings have also been found. The implications of the high rates of volcanic activity and the apparent abundance of sulfur on Io for the type of volcanism observed are discussed, and it is concluded that while there are strong arguments for sulfur flows on the surface of Io, silicate volcanism of the type observed on earth may also occur.

Carr, M. H.↗

Rotating-fluid experiments with an atmospheric general circulation model

In order to determine features of rotating fluid flow that are dependent on the geometry, rotating annulus-type experiments are carried out with a numerical model in spherical coordinates. Rather than constructing and testing a model expressly for this purpose, it is found expedient to modify an existing general circulation model of the atmosphere by removing the model physics and replacing the lower boundary with a uniform surface. A regime diagram derived from these model experiments is presented; its major features are interpreted and contrasted with the major features of rotating annulus regime diagrams. Within the wave regime, a narrow region is found where one or two zonal wave numbers are dominant. The results reveal no upper symmetric regime; wave activity at low rotation rates is thought to be maintained by barotropic rather than baroclinic processes.

Geisler, J. E.↗

Computational problems on composite grids

Most currently used algorithms for the numerical solution of the partial differential equations encountered in fluid flow problems can be implemented on composite grid systems. Finite volume formulations are easier to derive on composite grids, and may in principle be derived for partial differential equations of all types. Except when using Alternating Difference Implicit-type schemes, the overlapping of grids is an alternative to the more common grid construction procedure where grid lines continue smoothly from one subregion to the next. In the solution of model problems, the correct choice of an interpolation formula has been found able to reduce errors by a factor of two.

Mastin, C. W.↗

A finite element surface impedance representation for steady-state problems

A procedure for determining the scattered pressure field resulting from a monochromatic harmonic wave that is incident upon a layer energy absorbing structure is treated. The situation where the structure is modeled with finite elements and the surrounding acoustic medium (water or air) is represented with either acoustic finite elements, or some type of boundary integral formulation, is considered. Finite element modeling problems arise when the construction of the structure, at the fluid structure interface, are nonhomogeneous and in particular, when the inhomogeneities are small relative to the acoustic wave length. An approximate procedure is presented for replacing the detailed microscopic representation of the layered surface configuration with an equivalent simple surface impedance finite element, which is especially designed to work only at limited frequencies. An example problem is presented using NASTRAN. However, the procedure is general enough to adapt to practically any finite element code having a steady state option.

Kalinowski, A. J.↗

Iterative methods for mixed finite element equations

Iterative strategies for the solution of indefinite system of equations arising from the mixed finite element method are investigated in this paper with application to linear and nonlinear problems in solid and structural mechanics. The augmented Hu-Washizu form is derived, which is then utilized to construct a family of iterative algorithms using the displacement method as the preconditioner. Two types of iterative algorithms are implemented. Those are: constant metric iterations which does not involve the update of preconditioner; variable metric iterations, in which the inverse of the preconditioning matrix is updated. A series of numerical experiments is conducted to evaluate the numerical performance with application to linear and nonlinear model problems.

Nakazawa, S.↗

Perspectives on knowledge in engineering design

Various perspectives are given of the knowledge currently used in engineering design, specifically dealing with knowledge-based expert systems (KBES). Constructing an expert system often reveals inconsistencies in domain knowledge while formalizing it. The types of domain knowledge (facts, procedures, judgments, and control) differ from the classes of that knowledge (creative, innovative, and routine). The feasible tasks for expert systems can be determined based on these types and classes of knowledge. Interpretive tasks require reasoning about a task in light of the knowledge available, where generative tasks create potential solutions to be tested against constraints. Only after classifying the domain by type and level can the engineer select a knowledge-engineering tool for the domain being considered. The critical features to be weighed after classification are knowledge representation techniques, control strategies, interface requirements, compatibility with traditional systems, and economic considerations.

Rasdorf, W. J.↗

UV flux distributions of novalike variables

Previous estimates of distance, reddening, orbital inclination, and white dwarf mass for a sample of nine nova-like cataclysmic variables are presented, along with their representative IUE fluxes. Blackbody and Kurucz (1979) model atmosphere fluxes are used to construct sequences of model accretion disk spectra. It is found that the Kurucz-type accretion disk models do not reproduce simultaneously the UV flux level and color.

Wade, Richard A.↗

Alternative Processes for Water Reclamation and Solid Waste Processing in a Physical/chemical Bioregenerative Life Support System

Viewgraphs on alternative processes for water reclamation and solid waste processing in a physical/chemical-bioregenerative life support system are presented. The main objective is to focus attention on emerging influences of secondary factors (i.e., waste composition, type and level of chemical contaminants, and effects of microorganisms, primarily bacteria) and to constructively address these issues by discussing approaches which attack them in a direct manner.

Rogers, Tom D.↗