SEARCH · Engineering Papers

Results for “conformance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Planetary and deep space requirements for photovoltaic solar arrays

In the past 25 years, the majority of interplanetary spacecraft have been powered by nuclear sources. However, as the emphasis on smaller, low cost missions gains momentum, the majority of missions now being planned will use photovoltaic solar arrays. This will present challenges to the solar array builders, inasmuch as planetary requirements usually differ from earth orbital requirements. In addition, these requirements often differ greatly, depending on the specific mission; for example, inner planets vs. outer planets, orbiters vs. flybys, spacecraft vs. landers, and so on. Also, the likelihood of electric propulsion missions will influence the requirements placed on solar array developers. The paper will discuss representative requirements for a range of planetary missions now in the planning stages. Insofar as inner planets are concerned, a Mercury orbiter is being studied with many special requirements. Solar arrays would be exposed to high temperatures and a potentially high radiation environment, and will need to be increasingly pointed off sun as the vehicle approaches Mercury. Identification and development of cell materials and arrays at high incidence angles will be critical to the design. Missions to the outer solar system that have been studied include a Galilean orbiter and a flight to the Kuiper belt. While onboard power requirements would be small (as low as 10 watts), the solar intensity will require relatively large array areas. As a result, such missions will demand extremely compact packaging and low mass structures to conform to launch vehicle constraints. In turn, the large are, low mass designs will impact allowable spacecraft loads. Inflatable array structures, with and without concentration, and multiband gap cells will be considered if available. In general, the highest efficiency cell technologies operable under low intensity, low temperature conditions are needed. Solar arrays will power missions requiring as little as approximately 100 watts, up to several kilowatts (at Earth) in the case of solar electric propulsion missions. Thus, mass and stowage volume minimization will be required over a range of array sizes. Concentrator designs, inflatable structures, and the combination of solar arrays with the telecommunications system have been proposed. Performance, launch vehicle constraints, an cost will be the principal parameters in the design trade space. Other special applications will also be discussed, including requirements relating to planetary landers and probes. In those cases, issues relating to shock loads on landing, operability in (possibly dusty) atmospheres, and extreme temperature cycles must be considered, in addition to performance, stowed volume, and costs.

Bankston, C. P.↗

NASA NTRS1992

Development of IR radiation simulator for spacecraft thermal testing

The aim was to simulate, in a ground test, the solar radiation environment to which the Ofeq satellite would be exposed in orbit. The solar simulator usually used is very expensive, as are its operation and maintenance, therefore an infrared (IR) simulator was used; its development involved the creation of uniform IR fluxes onto the irregular geometry of a spacecraft. The tests were carried out on a thermal model of the satellite and the model was verified in a solar simulator test at a European space center. Heat flux mapping software was developed to plan the positioning of the heating elements which generated the IR fluxes and a system was built for heat flux and temperature monitoring and control. A special heat flux sensor was developed to measure the energy absorbed by the satellite surfaces; its calibration had to be independent of wavelength, so that the measurements obtained at IR wavelengths would be equivalent to the actual solar radiation effects. The results of the verification experiment are presented; their conformity with predicted values indicates that the technique developed is a suitable tool for satellite design verification.

Shimrony, Yoram↗

NASA NTRS1995

The specification-based validation of reliable multicast protocol: Problem Report

Reliable Multicast Protocol (RMP) is a communication protocol that provides an atomic, totally ordered, reliable multicast service on top of unreliable IP multicasting. In this report, we develop formal models for RMP using existing automated verification systems, and perform validation on the formal RMP specifications. The validation analysis help identifies some minor specification and design problems. We also use the formal models of RMP to generate a test suite for conformance testing of the implementation. Throughout the process of RMP development, we follow an iterative, interactive approach that emphasizes concurrent and parallel progress of implementation and verification processes. Through this approach, we incorporate formal techniques into our development process, promote a common understanding for the protocol, increase the reliability of our software, and maintain high fidelity between the specifications of RMP and its implementation.

Wu, Yunqing↗

NASA NTRS1995

Inverse sequential procedures for the monitoring of time series

When one or more new values are added to a developing time series, they change its descriptive parameters (mean, variance, trend, coherence). A 'change index (CI)' is developed as a quantitative indicator that the changed parameters remain compatible with the existing 'base' data. CI formulate are derived, in terms of normalized likelihood ratios, for small samples from Poisson, Gaussian, and Chi-Square distributions, and for regression coefficients measuring linear or exponential trends. A substantial parameter change creates a rapid or abrupt CI decrease which persists when the length of the bases is changed. Except for a special Gaussian case, the CI has no simple explicit regions for tests of hypotheses. However, its design ensures that the series sampled need not conform strictly to the distribution form assumed for the parameter estimates. The use of the CI is illustrated with both constructed and observed data samples, processed with a Fortran code 'Sequitor'.

Radok, Uwe↗

NASA NTRS1996

Wing Twist Measurements at the National Transonic Facility

A technique for measuring wing twist currently in use at the National Transonic Facility is described. The technique is based upon a single camera photogrammetric determination of two dimensional coordinates with a fixed (and known) third dimensional coordinate. The wing twist is found from a conformal transformation between wind-on and wind-off 2-D coordinates in the plane of rotation. The advantages and limitations of the technique as well as the rationale for selection of this particular technique are discussed. Examples are presented to illustrate run-to-run and test-to-test repeatability of the technique in air mode. Examples of wing twist in cryogenic nitrogen mode are also presented.

Burner, Alpheus W.↗

NASA NTRS1995

A test of a vortex method for the computation of flap side edge noise

Upon approach to landing, a major source location of airframe noise occurs at the side edges of the part span, trailing edge flaps. In the vicinity of these flaps, a complex arrangement of spanwise flow with primary and secondary tip vortices may form. Each of these vortices is observed to become fully three-dimensional. In the present study, a numerical model is developed to investigate the noise radiated from the side edge of a flap. The inherent three-dimensionality of this flow forces us to carefully consider a numerical scheme which will be both accurate in its prediction of the flow acoustics and also computationally efficient. Vortex methods have offered a fast and efficient means of simulating many two and three-dimensional, vortex dominated flows. In vortex methods, the time development of the flow is tracked by following exclusively the vorticity containing regions. Through the Biot-Savart law, knowledge of the vorticity field enables one to obtain flow quantities at any desired location during the flow evolution. In the present study, a numerical procedure has been developed which incorporates the Lagrangian approach of vortex methods into a calculation for the noise radiated by a flow-surface interaction. In particular, the noise generated by a vortex in the presence of a flat half plane is considered. This problem serves as a basic model of flap edge flow. It also permits the direct comparison between our computed results and previous acoustic analyses performed for this problem. In our numerical simulations, the mean flow is represented by the complex potential W(z) = Aiz(exp l/2), which is obtained through conformal mapping techniques. The magnitude of the mean flow is controlled by the parameter A. This mean flow has been used in the acoustic analysis by Hardin and is considered a reasonable model of the flow field in the vicinity of the edge and away from the leading and trailing edges of the flap. To represent the primary vortex which occurs near the flap, a point vortex is introduced just below the flat half plane. Using a technique from panel methods, boundary conditions on the flap surface are satisfied by the introduction of a row of stationary point vortices along the extent of the flap. At each time step in the calculation, the strength of these vortices is chosen to eliminate the normal velocity at intermediary collocation points. The time development of the overall flow field is then tracked using standard techniques from vortex methods. Vortex trajectories obtained through this computation are in good agreement with those predicted by the analytical solution given by Hardin, thus verifying the viability of this procedure for more complex flow arrangements. For the flow acoustics, the Ffowcs Williams-Hawkings equation is numerically integrated. This equation supplies the far field acoustic pressure based upon pressures occurring along the flap surface. With our vortex method solution, surface pressures may be obtained with exceptional resolution. The Ffowcs Williams-Hawkings equation is integrated using a spatially fourth order accurate Simpson's rule. Rational function interpolation is used to obtain the surface pressures at the appropriate retarded times. Comparisons between our numerical results for the acoustic pressure and those predicted by the Hardin analysis have been made. Preliminary results indicate the need for an improved integration technique. In the future, the numerical procedure developed in this study will be applied to the case of a rectangular flap of finite thickness and ultimately modified for application to the fully three-dimensional problem.

Martin, James E.↗

NASA NTRS1995

The Specification-Based Validation of Reliable Multicast Protocol

Reliable Multicast Protocol (RMP) is a communication protocol that provides an atomic, totally ordered, reliable multicast service on top of unreliable IP multicasting. In this report, we develop formal models for RMP using existing automated verification systems, and perform validation on the formal RMP specifications. The validation analysis help identifies some minor specification and design problems. We also use the formal models of RMP to generate a test suite for conformance testing of the implementation. Throughout the process of RMP development, we follow an iterative, interactive approach that emphasizes concurrent and parallel progress of the implementation and verification processes. Through this approach, we incorporate formal techniques into our development process, promote a common understanding for the protocol, increase the reliability of our software, and maintain high fidelity between the specifications of RMP and its implementation.

Wu, Yunqing↗

NASA NTRS1995

Solar wind theory and modelling

The outflow of coronal plasma into interplanetary space is a consequence of the coronal heating process. Therefore the formation of the corona and the acceleration of the solar wind should be treated as a single problem. Traditionally the mass or particle flux emanating from the extended corona has been thought of as being determined by the coronal temperature or scale height and the coronal (base) density. This argument follows from considerations of the momentum balance of the corona-wind system from which one obtains models of a close to hydrostatic corona out to the critical point where the flow becomes supersonic. With this approach to the acceleration of the wind is has been difficult to reconcile the relatively small variation observed in the proton flux at 1 AU with the predicted exponential dependence of the proton flux on the coronal temperature. In this talk we would like to emphasize another approach in which coronal energetics play the primary role. The deposition of energy into the corona through some 'mechanical' energy flux is balanced by the various energy sinks available to the corona and the sum of these processes determine the coronal structure, i.e. its temperature and density. The corona loses energy through heat conduction into the transition region, through radiative losses, and through the gravitational potential energy and kinetic energy put into the solar wind itself. We will show from a series of models of the chromosphere transition region-corona-solar wind system that most of the energy deposited in a magnetically open region will go into the solar wind, with roughly half going into kinetic energy and half into lifting the plasma out of the solar gravity field. The coronal base density will adjust itself in such a way that the heat conductive flux flowing into the transition region is radiated away in the upper chromosphere. The coronal temperature is set by the requirements that most of the deposited energy goes into accelerating the solar wind; the coronal scale height will adjust itself so that the solar wind energy losses conform to the amplitude of the input energy. These processes are modified by the 'mode' of energy deposition, and we will show the effects on coronal structure of changing the parameters describing coronal heating as well as the effects of including a helium fluid in the models. However, the location, scale height and/or form of the energy deposition (i.e. heating or direct acceleration) are not too important for the solar wind, the coronal density and temperature structure will vary with the 'mode' of energy deposition, but the solar wind mass flux depends mainly on the amplitude of the energy flux.

Hansteen, Viggo H.↗

NASA NTRS1994

Microwave Sensor for Ice Detection

A microwave technique has been developed for detecting ice build-up on the wing surfaces of commercial airliners and highway bridges. A microstrip patch antenna serves as the sensor, with changes in the resonant frequency and impedance being dependent upon the overlying layers of ice, water, and glycol mixtures. The antenna sensor is conformably mounted on the wing. The depth and dielectric constants of the layers are measured by comparing the complex resonant admittance with a calibrated standard. An initial breadboard unit has been built and tested. Additional development is now underway.

Arndt, G. D.↗

NASA NTRS1994

Application Reuse Library for Software, Requirements, and Guidelines

Better designs are needed for expert systems and other operations automation software, for more reliable, usable and effective human support. A prototype computer-aided Application Reuse Library shows feasibility of supporting concurrent development and improvement of advanced software by users, analysts, software developers, and human-computer interaction experts. Such a library expedites development of quality software, by providing working, documented examples, which support understanding, modification and reuse of requirements as well as code. It explicitly documents and implicitly embodies design guidelines, standards and conventions. The Application Reuse Library provides application modules with Demo-and-Tester elements. Developers and users can evaluate applicability of a library module and test modifications, by running it interactively. Sub-modules provide application code and displays and controls. The library supports software modification and reuse, by providing alternative versions of application and display functionality. Information about human support and display requirements is provided, so that modifications will conform to guidelines. The library supports entry of new application modules from developers throughout an organization. Example library modules include a timer, some buttons and special fonts, and a real-time data interface program. The library prototype is implemented in the object-oriented G2 environment for developing real-time expert systems.

Malin, Jane T.↗

NASA NTRS1996

F-18 HARV With Nose Strakes For Forebody Vortex Control

Nose of F-18 High Alpha Research Vehicle (HARV) modified with conformal, mechanically actuated nose strakes for enhanced rolling (ANSER). Forebody vortex control effected by use of actuated strakes and/or other flow-control devices. System provides means to evaluate design tradeoffs.

Bowers, Albion H.↗

NASA NTRS1996

There aren't Non-Standard Solutions for the Braid Group Representations of the QYBE Associated with 10-D Representations of SU(4)

It is well known that the quantum Yang-Baxter equations (QYBE) play an important role in various theoretical and mathematical physics, such as completely integrable system in (1 + 1)-dimensions, exactly solvable models in statistical mechanics, the quantum inverse scattering method and the conformal field theories in 2-dimensions. Recently, much remarkable progress has been made in constructing the solutions of the QYBE associated with the representations of lie algebras. It is shown that for some cases except the standard solutions, there also exist new solutions, but the others have not non-standard solutions. In this paper by employing the weight conservation and the diagrammatic techniques we show that the solution associated with the 10-D representations of SU (4) are standard alone.

Yijun, Huang↗

NASA NTRS1996

Microstrip patch antenna receiving array operating in the Ku band

Microstrip patch antennas were first investigated from the idea that it would be highly advantageous to fabricate radiating elements (antennas) on the same dielectric substrate as RF circuitry and transmission lines. Other advantages were soon discovered to be its lightweight, low profile, conformability to shaped surfaces, and low manufacturing costs. Unfortunately, these same patches continually exhibit narrow bandwidths, wide beamwidths, and low antenna gain. This thesis will present the design and experimental results of a microstrip patch antenna receiving array operating in the Ku band. An antenna array will be designed in an attempt to improve its performance over a single patch. Most Ku band information signals are either wide band television images or narrow band data and voice channels. An attempt to improve the gain of the array by introducing parasitic patches on top of the array will also be presented in this thesis.

Walcher, Douglas A.↗

NASA NTRS1996

Optimization Methodology for Unconventional Rocket Nozzle Design

Several current rocket engine concepts such as the bell-annular tripropellant engine, and the linear aerospike being proposed for the X-33, require unconventional three-dimensional rocket nozzles which must conform to rectangular or sector-shaped envelopes to meet integration constraints. These types of nozzles exist outside the current experience database, therefore, development of efficient design methods for these propulsion concepts is critical to the success of launch vehicle programs. Several approaches for optimizing rocket nozzles, including streamline tracing techniques, and the coupling of CFD analysis to optimization algorithms are described. The relative strengths and weaknesses of four classes of optimization algorithms are discussed: Gradient based methods, genetic algorithms, simplex methods, and surface response methods. Additionally, a streamline tracing technique, which provides a very computationally efficient means of defining a three-dimensional contour, is discussed. The performance of the various optimization methods on thrust optimization problems for tripropellant and aerospike concepts is assessed and recommendations are made for future development efforts.

Follett, W.↗

NASA NTRS1996

Application of Optimization Techniques to Design of Unconventional Rocket Nozzle Configurations

Several current rocket engine concepts such as the bell-annular tri-propellant engine, and the linear aerospike being proposed for the X-33 require unconventional three dimensional rocket nozzles which must conform to rectangular or sector shaped envelopes to meet integration constraints. These types of nozzles exist outside the current experience database, therefore, the application of efficient design methods for these propulsion concepts is critical to the success of launch vehicle programs. The objective of this work is to optimize several different nozzle configurations, including two- and three-dimensional geometries. Methodology includes coupling computational fluid dynamic (CFD) analysis to genetic algorithms and Taguchi methods as well as implementation of a streamline tracing technique. Results of applications are shown for several geometeries including: three dimensional thruster nozzles with round or super elliptic throats and rectangualar exits, two- and three-dimensional thrusters installed within a bell nozzle, and three dimensional thrusters with round throats and sector shaped exits. Due to the novel designs considered for this study, there is little experience which can be used to guide the effort and limit the design space. With a nearly infinite parameter space to explore, simple parametric design studies cannot possibly search the entire design space within the time frame required to impact the design cycle. For this reason, robust and efficient optimization methods are required to explore and exploit the design space to achieve high performance engine designs. Five case studies which examine the application of various techniques in the engineering environment are presented in this paper.

Follett, W.↗

NASA NTRS1996

Managing Approach Plate Information Study (MAPLIST): An Information Requirements Analysis of Approach Chart Use

Adequately presenting all necessary information on an approach chart represents a challenge for cartographers. Since many tasks associated with using approach charts are cognitive (e.g., planning the approach and monitoring its progress), and since the characteristic of a successful interface is one that conforms to the users' mental models, understanding pilots' underlying models of approach chart information would greatly assist cartographers. To provide such information, a new methodology was developed for this study that enhances traditional information requirements analyses by combining psychometric scaling techniques with a simulation task to provide quantifiable links between pilots' cognitive representations of approach information and their use of approach information. Results of this study should augment previous information requirements analyses by identifying what information is acquired, when it is acquired, and what presentation concepts might facilitate its efficient use by better matching the pilots' cognitive model of the information. The primary finding in this study indicated that pilots mentally organize approach chart information into ten primary categories: communications, geography, validation, obstructions, navigation, missed approach, final items, other runways, visibility requirement, and navigation aids. These similarity categories were found to underlie the pilots' information acquisitions, other mental models, and higher level cognitive processes that are used to accomplish their approach and landing tasks.

Ricks, Wendell R.↗

NASA NTRS1996

Role of the BIPM in UTC Dissemination to the Real Time User

The generation and dissemination of International Atomic Time (TAI), and Coordinated Universal Time (UTC) are explicitly mentioned in the list of principal tasks of the Bureau International des Poids et Mesures (BIPM), that appears in the Compes Rendus of the the 18e Conference Generales des Poids et Measures, in 1987. These time scales are used as the ultimate reference in the most demanding scientific applications and must, therefore, be of the best metrological quality in terms of reliability, long term stability, and conformity of the scale interval with the second, the unit of time of the International System of Units. To meet these requirements, it is necessary that the readings of the atomic clocks, spread all over the world, that are used as basic timing data for TAI and UTC generation, must be combined in the most efficient way possible. In particular, to take full advantage of the quality of each contributing clock calls for observation of its performance over a sufficiently long time. At present, the computation period treats data in blocks covering two months. TAI and UTC are thus deferred-time scales that cannot be immediately available to real-time users. The BIPM can, nevertheless be of help to real-time users. The predictability of UTC is a fundamental attribute of the scale for institutions responsible for the dissemination of real-time time scales. It allows them to improve their local representations of UTC and, thus, implement a more thorough steering of the time scales diffused in real-time. With a view to improving the predicatbility of UTC, the BIPM examines in detail timing techniques and basic theories in order to propose alternative solutions for timing algorithms. This, coupled with a recent improvement of timing data, makes UTC more stable and thus, more predictable. At a more practical level, effort is being devoted to putting in place automatic procedures for reducing the time needed for data collection and treatment: monthly results are already available ten days earlier than before.

Quinn, T. J.↗

NASA NTRS1996

Long-term archiving and data access: modelling and standardization

This paper reports on the multiple difficulties inherent in the long-term archiving of digital data, and in particular on the different possible causes of definitive data loss. It defines the basic principles which must be respected when creating long-term archives. Such principles concern both the archival systems and the data. The archival systems should have two primary qualities: independence of architecture with respect to technological evolution, and generic-ness, i.e., the capability of ensuring identical service for heterogeneous data. These characteristics are implicit in the Reference Model for Archival Services, currently being designed within an ISO-CCSDS framework. A system prototype has been developed at the French Space Agency (CNES) in conformance with these principles, and its main characteristics will be discussed in this paper. Moreover, the data archived should be capable of abstract representation regardless of the technology used, and should, to the extent that it is possible, be organized, structured and described with the help of existing standards. The immediate advantage of standardization is illustrated by several concrete examples. Both the positive facets and the limitations of this approach are analyzed. The advantages of developing an object-oriented data model within this contxt are then examined.

Hoc, Claude↗