SEARCH · Engineering Papers

Results for “compression rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Analysis of Water Recovery Rate from the Heat Melt Compactor

Human space missions generate trash with a substantial amount of plastic (20% or greater by mass). The trash also contains water trapped in food residue and paper products and other trash items. The Heat Melt Compactor (HMC) under development by NASA Ames Research Center (ARC) compresses the waste, dries it to recover water and melts the plastic to encapsulate the compressed trash. The resulting waste disk or puck represents an approximately ten-fold reduction in the volume of the initial trash loaded into the HMC. In the current design concept being pursued, the trash is compressed by a piston after it is loaded into the trash chamber. The piston face, the side walls of the waste processing chamber and the end surface in contact with the waste can be heated to evaporate the water and to melt the plastic. Water is recovered by the HMC in two phases. The first is a pre-process compaction without heat or with the heaters initially turned on but before the waste heats up. Tests have shown that during this step some liquid water may be expelled from the chamber. This water is believed to be free water (i.e., not bound with or absorbed in other waste constituents) that is present in the trash. This phase is herein termed Phase A of the water recovery process. During HMC operations, it is desired that liquid water recovery in Phase A be eliminated or minimized so that water-vapor processing equipment (e.g., condensers) downstream of the HMC are not fouled by liquid water and its constituents (i.e., suspended or dissolved matter) exiting the HMC. The primary water recovery process takes place next where the trash is further compacted while the heated surfaces reach their set temperatures for this step. This step will be referred to herein as Phase B of the water recovery process. During this step the waste chamber may be exposed to different selected pressures such as ambient, low pressure (e.g., 0.2 atm), or vacuum. The objective for this step is to remove both bound and any remaining free water in the trash by evaporation. The temperature settings of the heated surfaces are usually kept above the saturation temperature of water but below the melting temperature of the plastic in the waste during this step to avoid any encapsulation of wet trash which would reduce the amount of recovered water by blocking the vapor escape. In this paper, we analyze the water recovery rate during Phase B where the trash is heated and water leaves the waste chamber as vapor, for operation of the HMC in reduced gravity. We pursue a quasi-one-dimensional model with and without sidewall heating to determine the water recovery rate and the trash drying time. The influences of the trash thermal properties, the amount of water loading, and the distribution of the water in the trash on the water recovery rates are determined.

Heat Melt Compactor↗

NASA NTRS2001

An extensometer for global measurement of bone strain suitable for use in vivo in humans

An axial extensometer able to measure global bone strain magnitudes and rates encountered during physiological activity, and suitable for use in vivo in human subjects, is described. The extensometer uses paired capacitive sensors mounted to intraosseus pins and allows measurement of strain due to bending in the plane of the extensometer as well as uniaxial compression or tension. Data are presented for validation of the device against a surface-mounted strain gage in an acrylic specimen under dynamic four-point bending, with square wave and sinusoidal loading inputs up to 1500 mu epsilon and 20 Hz, representative of physiological strain magnitudes and frequencies. Pearson's correlation coefficient (r) between extensometer and strain gage ranged from 0.960 to 0.999. Mean differences between extensometer and strain gage ranged up to 15.3 mu epsilon. Errors in the extensometer output were directly proportional to the degree of bending that occurs in the specimen, however, these errors were predictable and less than 1 mu epsilon for the loading regime studied. The device is capable of tracking strain rates in excess of 90,000 mu epsilon/s.

Non-NASA Center↗

DOE OSTI2022

Pressure–Strain Interaction as the Energy Dissipation Estimate in Collisionless Plasma

The dissipative mechanism in weakly collisional plasma is a topic that pervades decades of studies without a consensus solution. We compare several energy dissipation estimates based on energy transfer processes in plasma turbulence and provide justification for the pressure–strain interaction as a direct estimate of the energy dissipation rate. The global and scale-by-scale energy balances are examined in 2.5D and 3D kinetic simulations. We show that the global internal energy increase and the temperature enhancement of each species are directly tracked by the pressure–strain interaction. The incompressive part of the pressure–strain interaction dominates over its compressive part in all simulations considered. The scale-by-scale energy balance is quantified by scale filtered Vlasov–Maxwell equations, a kinetic plasma approach, and the lag dependent von Kármán–Howarth equation, an approach based on fluid models. We find that the energy balance is exactly satisfied across all scales, but the lack of a well-defined inertial range influences the distribution of the energy budget among different terms in the inertial range. Therefore, the widespread use of the Yaglom relation in estimating the dissipation rate is questionable in some cases, especially when the scale separation in the system is not clearly defined. In contrast, the pressure–strain interaction balances exactly the dissipation rate at kinetic scales regardless of the scale separation.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2025

Landscape of Cross-Laminated Timber in the United States

Mass timber construction is an emerging sustainable construction practice in the United States given its renewable nature and its ability to store carbon during its use. Cross-laminated timber (CLT) is a type of mass timber construction that involves a wood panel system that is manufactured by gluing alternating lumber board layers at right angles. CLT panels have high strength, dimensional stability, and the ability to resist high compressive forces. They are considered a sustainable alternative to reinforced concrete construction because of the renewable nature of the primary wood material in CLT panels. Despite its environmental and structural benefits, the adoption rate of CLT remains low. This report investigates the current landscape of CLT use in buildings, providing information on the types of building that use CLT, how those buildings are used, and in what U.S. regions CLT is manufactured and used. This information helps identify potential barriers to adoption to inform ways to reduce these barriers. This review synthesizes insights from recent studies to offer a detailed perspective on the state of CLT adoption, its barriers, and the evolving landscape of opportunities that may facilitate its broader acceptance and use.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS1966

Bellows joint absorbs torsional deflections in duct system

Long, thin-walled bellows compressed into a short length absorbs the same amount of torsional deflection as the same tube in full length condition and saves in cost, complexity and space. This bellows has lower torsional spring rate to absorb the bulk of the duct assembly tortional deflections, leaving the other bellows free to absorb axial and angular deflections.

Daniels, C. M.↗

NASA NTRS1972

Tables of critical-flow functions and thermodynamic properties for methane and computational procedures for both methane and natural gas

Procedures for calculating the mass flow rate of methane and natural gas through nozzles are given, along with the FORTRAN 4 subroutines used to make these calculations. Three sets of independent variables are permitted in these routines. In addition to the plenum pressure and temperature, the third independent variable is either nozzle exit pressure, Mach number, or temperature. A critical-flow factor that becomes a convenient means for determining the mass flow rate of methane through critical-flow nozzles is tabulated. Other tables are included for nozzle throat velocity and critical pressure, density, and temperature ratios, along with some thermodynamic properties of methane, including compressibility factor, enthalpy, entropy, specific heat, specific-heat ratio, and speed of sound. These tabulations cover a temperature range from 120 to 600 K and pressures to 3 million N/sq m.

Johnson, R. C.↗

NASA NTRS1974

Out-of-pile creep behavior of uranium carbide

Compression creep tests were investigated on various UC-based fuel materials having a variation in both density and composition. Specimens were prepared by casting and by hot pressing. Steady-state creep rates were measured under vacuum at 1400 to 1800 C in the stress range 500-4000 psi.

Wright, T. R.↗

NASA NTRS1978

Elasticity of excised dog lung parenchyma

An optical-electromechanical system is used to measure the force-deformation behavior of biaxially loaded rectangular slabs of excised dog lung parenchyma. In the course of the study, the effects of time, the consistency of reference lengths and areas, the presence of hysteresis, the necessity of preconditioning, the repeatability of results, the effects of lateral load, the effect of strain rate, the effect of pH, the influence of temperature, and the variations among specimens are considered. A new finding is that there is a change in elastic behavior when the tissue undergoes a compressive strain. When the tissue is in tension, increasing the lateral load decreases the compliance, whereas the opposite is true when compressive strain is present.

Vawter, D. L.↗

NASA NTRS1983

A study of stiffness, residual strength and fatigue life relationships for composite laminates

Qualitative and quantitative exploration of the relationship between stiffness, strength, fatigue life, residual strength, and damage of unnotched, graphite/epoxy laminates subjected to tension loading. Clarification of the mechanics of the tension loading is intended to explain previous contradictory observations and hypotheses; to develop a simple procedure to anticipate strength, fatigue life, and stiffness changes; and to provide reasons for the study of more complex cases of compression, notches, and spectrum fatigue loading. Mathematical models are developed based upon analysis of the damage states. Mathematical models were based on laminate analysis, free body type modeling or a strain energy release rate. Enough understanding of the tension loaded case is developed to allow development of a proposed, simple procedure for calculating strain to failure, stiffness, strength, data scatter, and shape of the stress-life curve for unnotched laminates subjected to tension load.

Ryder, J. T.↗

NASA NTRS1985

Models of planetary structure and evolution: The case of Io

The interior structure of Jupiter's satellite Io is probably layered with a liquid core surrounded by a rigid mantle, a partially molten asthenosphere and a thin rigid lithosphere. The core radius could roughly equal half the planetary radius if the core is mostly FeS and if the mantle's compressibility is close to that of Earth's upper mantle rocks. The lithosphere thickness is controlled by the balance of the heat flux q sub e across the lithosphere with the tidal heating rate H within the lithosphere and the heat flux q; from the interior into the lithosphere. The maximum thickness determined by a balance of q sub e with H is probably much smaller than the lithosphere thickness that maximizes H. Thus, if Io's interior was once melted and if it's resonant orbital state is ancient it will freeze from the inside out. The time scale of internal and latent heat removal in a molten Io is 10 to the eighth power. Io's strong volcanic activity suggests the persistence of a partially molten asthenosphere to the present time.

Spohn, T.↗

NASA NTRS1990

Secondary instabilities in compressible boundary layers

Secondary instabilities are examined in compressible boundary layers at Mach numbers M(sub infinity) = 0, 0.8, 1.6, and 4.5. It is found that there is a broad-band of highly unstable 3-d secondary disturbances whose growth rates increase with increasing primary wave amplitude. At M(sub infinity) is less than or equal to 1.6, fundamental resonance dominates at relatively high (2-d) primary disturbance amplitude, while subharmonic resonance is characterized by a low (2-d) primary amplitude. At M(sub infinity) = 4.5, the subharmonic instability which arises from the second mode disturbance is the strongest type of secondary instability. The influence of the inclination, theta, of the primary wave with respect to the mean flow direction on secondary instability is investigated at M(sub infinity) = 1.6 for small to moderate values of theta. It is found that the strongest fundamental instability occurs when the primary wave is inclined at 10 deg to the mean flow direction, although a 2-d primary mode yields the most amplified subharmonic. The subharmonic instability at a high value of theta (namely, theta = 45 deg) is also discussed. Finally, a subset of the secondary instability results are compared against direct numerical simulations.

Ng, Lian↗

NASA NTRS1991

Slow crack growth in glass in combined mode I and mode II loading

Slow crack growth in soda-lime glass under combined mode I and mode II loading was investigated in precracked disk specimens in which pure mode I, pure mode II, and various combinations of mode I and mode II were achieved by loading in diametral compression at selected angles with respect to symmetric radial cracks. It is shown that slow crack growth under these conditions can be described by a simple exponential relationship with elastic strain energy release rate as the effective crack-driving force parameter. It is possible to interpret this equation in terms of theoretical models that treat subcritical crack growth as a thermally activated bond-rupture process with an activation energy dependent on the environment, and the elastic energy release rate as the crack-driving force parameter.

Shetty, D. K.↗

NASA NTRS1994

Matching Inviscid/Boundary Layer Flowfields

New boundary-layer equations are developed and the solutions match all the boundary-layer properties, except for the normal velocity, exactly with the corresponding inviscid properties. The numerical procedure solves tridiagonal matrices at each marching station. As part of the solution an inviscid transpiration velocity at the surface is calculated from the boundary-layer solution. This transpiration velocity could be used as a boundary condition to calculate a new inviscid solution. If the inviscid/boundary layer solutions are iterated, then the normal velocity from the boundary layer solution will match the inviscid values exactly. Solutions are calculated for shear flows over a flat plate. Results from the present method compared well with Navier-Stokes solutions for incompressible constant shear flow and sinusoidal shear flow. Iterations of the inviscid/boundary layer solutions were not necessary. Compressible flow of an exponential shear at Mach 4 was calculated for cold, adiabatic, and hot walls. It was found that inviscid shear flows have a significant effect on skin friction and heating rates. The present method should yield accurate boundary-layer solutions at Reynolds numbers lower than the traditional boundary-layer equations.

DeJarnette, Fred R.↗

NASA NTRS2001

Modeled Seasonal Variations of Firn Density Induced by Steady State Surface Air Temperature Cycle

Seasonal variations of firn density in ice-sheet firn layers have been attributed to variations in deposition processes or other processes within the upper firn. A recent high-resolution (mm scale) density profile, measured along a 181 m core from Antarctica, showed small-scale density variations with a clear seasonal cycle that apparently was not-related to seasonal variations in deposition or known near-surface processes (Gerland and others 1999). A recent model of surface elevation changes (Zwally and Li, submitted) produced a seasonal variation in firn densification, and explained the seasonal surface elevation changes observed by satellite radar altimeters. In this study, we apply our 1-D time-dependent numerical model of firn densification that includes a temperature-dependent formulation of firn densification based on laboratory measurements of grain growth. The model is driven by a steady-state seasonal surface temperature and a constant accumulation rate appropriate for the measured Antarctic ice core. The modeled seasonal variations in firn density show that the layers of snow deposited during spring to mid-summer with the highest temperature history compress to the highest density, and the layers deposited during later summer to autumn with the lowest temperature history compress to the lowest density. The initial amplitude of the seasonal difference of about 0.13 reduces to about 0.09 in five years and asymptotically to 0.92 at depth, which is consistent with the core measurements.

Jun, Li↗

DOE OSTI2021

Fracture Network Localization Preceding Catastrophic Failure in Triaxial Compression Experiments on Rocks

We quantify the spatial distribution of fracture networks throughout six in situ X-ray tomography triaxial compression experiments on crystalline rocks at confining stresses of 5–35 MPa in order to quantify how fracture development controls the final macroscopic failure of the rock, a process analogous to those that control geohazards such as earthquakes and landslides. Tracking the proportion of the cumulative volume of fractures with volumes >90th percentile to the total fracture volume, ∑ v 90 / v t o t indicates that the fracture networks tend to increase in localization toward these largest fractures for up to 80% of the applied differential stress. The evolution of this metric also matches the evolution of the Gini coefficient, which measures the deviation of a population from uniformity. These results are consistent with observations of localizing low magnitude seismicity before large earthquakes in southern California. In both this analysis and the present work, phases of delocalization interrupt the general increase in localization preceding catastrophic failure, indicating that delocalization does not necessarily indicate a reduction of seismic hazard. However, the proportion of the maximum fracture volume to the total fracture volume does not increase monotonically. Experiments with higher confining stress tend to experience greater localization. To further quantify localization, we compare the geometry of the largest fractures, with volumes >90th percentile, to the best fit plane through these fractures immediately preceding failure. The r 2 scores and the mean distance of the fractures to the plane indicate greater localization in monzonite than in granite. The smaller mean mineral diameter and lower confining stress in the granite experiments may contribute to this result. Tracking these various metrics of localization reveals a close association between macroscopic yielding and the acceleration of fracture network localization. Near yielding, ∑ v 90 / v t o t and the Gini coefficient increase while the mean distance to the final failure plane decreases. Macroscopic yielding thus occurs when the rate of fracture network localization increases.

58 GEOSCIENCES↗

NASA NTRS1992

Introduction to study and simulation of low rate video coding schemes

During this period, the development of simulators for the various HDTV systems proposed to the FCC were developed. These simulators will be tested using test sequences from the MPEG committee. The results will be extrapolated to HDTV video sequences. Currently, the simulator for the compression aspects of the Advanced Digital Television (ADTV) was completed. Other HDTV proposals are at various stages of development. A brief overview of the ADTV system is given. Some coding results obtained using the simulator are discussed. These results are compared to those obtained using the CCITT H.261 standard. These results in the context of the CCSDS specifications are evaluated and some suggestions as to how the ADTV system could be implemented in the NASA network are made.

Source record↗

DOE OSTI2020

A cavitation and dynamic void growth model for a general class of strain-softening amorphous materials

In this work, we derive a homogenized framework for cavitation and dynamic void growth in a general class of strain-softening materials with particular emphasis on amorphous materials. Analytic solutions are derived by considering an assemblage of spherical shells subject to dynamic hydrostatic tensile pressure. The isochoric response of the matrix material is captured by a free volume theory based amorphous viscoplasticity model. The framework accounts for the coupled rate-dependent, strain-softening behavior typically exhibited in amorphous materials. Validation of the homogenized theory is carried out against numerous direct numerical simulations with excellent agreement. Furthermore, we find that a reduction in cavitation strength and significant acceleration of dynamic void growth rates is induced as a consequence of strain-softening in the amorphous matrix material. Lastly, the model is utilized to interpret some non-intuitive experimental observations of amorphous materials subject to shock compression and subsequent spall failure.

36 MATERIALS SCIENCE↗

DOE OSTI2022

MemGaze: Rapid and Effective Load-Level Memory Trace Analysis

A major challenge of memory analysis tools is combining high-resolution analysis and low overhead measurement. Currently, hardware/software-based analysis of load-level sequences incurs time slowdowns of O(100×). We present MemGaze, a tool for low-overhead, high-resolution memory analysis. MemGaze uses Intel’s Processor Tracing (PT) instruction ptwrite to collect sampled and compressed memory address traces for load-level, sequence-aware analysis of data reuse. We describe multi-resolution analysis for locations vs. operations, accesses vs. spatio-temporal reuse, and reuse (distance, rate, volume) vs. access patterns. Both trace size and resolution are controllable. We use MemGaze to elucidate the memory effects of different data structures and algorithms. For sampled traces that are ˜1% of a full one, analysis metrics have 1-25% MAPE for histograms of varying dynamic sequence lengths. With current suboptimal kernel support (PT runs continuously), MemGaze’s time overhead is typically 10–95%; 7× at worst. However, when PT runs only during samples, overhead is 10–35% on memory intensive regions and correlates with executed ptwrites.

Kilic, Ozgur O.↗