SEARCH · Engineering Papers

Results for “active solids”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Co-introduction of precipitate hardening and TRIP in a TWIP high-entropy alloy using friction stir alloying

Tuning deformation mechanisms is imperative to overcome the well-known strength-ductility paradigm. Twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP) and precipitate hardening have been investigated separately and have been altered to achieve exceptional strength or ductility in several alloy systems. In this study, we use a novel solid-state alloying method—friction stir alloying (FSA)—to tune the microstructure, and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. During the FSA process, grains of the as-cast face-centered cubic matrix were refined by high-temperature severe plastic deformation and, subsequently, a new alloy composition was obtained by dissolving Ti into the matrix. After annealing the FSA specimen at 900 °C, hard Ni–Ti rich precipitates formed to strengthen the alloy. An additional result was a Ni-depleted region in the vicinity of newly-formed precipitates. The reduction in Ni locally reduced the stacking fault energy, thus inducing TRIP-based deformation while the remaining matrix still deformed as a result of TWIP. Our current approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Elucidating the reversible exsolution–dissolution behaviour of high-entropy oxides in crystalline and amorphous phases

High-entropy oxides (HEOs), as a subclass of high-entropy materials (HEMs), offer a versatile platform for catalysis by leveraging entropy-stabilized solid solutions with tunable compositions, lattice structures, and electronic properties. While exsolution–dissolution of metal species in crystalline HEOs has emerged as a promising strategy for reversible active sites regeneration, the dynamic behaviour of HEOs possessing amorphous nature remains under-explored, particularly the difference with crystalline counterparts. In this work, we systematically investigate the architecture-dependent exsolution–dissolution behavior of HEOs by comparing a crystalline-phase HEO (c-HEO) and an amorphous-phase HEO (a-HEO), both comprising Ni, Mg, Cu, Zn, and Co as principal metal elements. Using a combination of in situ variable-temperature X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), electron microscopy, and in situ CO diffuse reflectance infrared Fourier transform spectroscopy (CO-DRIFTS), the structural evolution of the two HEO phases under redox conditions was elucidated. Both materials exhibit reversible exsolution of metallic species or alloys in reducing environments, followed by re-incorporation into the host lattice upon oxidation. Remarkably, the a-HEO demonstrates more facile and dynamic self-healing behavior, with alloy exsolution and dissolution occurring under milder conditions because of its enhanced reducibility and structural disorder. This study provides critical insights into the design of next-generation regenerable catalysts based on amorphous HEOs, highlighting the role of phase structure in governing reversible metal-site formation dynamics and catalytic performance.

Wang, Qingju [Univ. of Tennessee, Knoxville, TN (U↗

DOE OSTI2022

A Fast-Response High-Accuracy Overvoltage Protection Circuit for Soft-Switching Current-Source Converters

Although voltage-source converters (VSCs) have been a focus of research for decades and are widely applied in numerous applications, they face great challenges in short-circuit failures, high dv/dt and electromagnetic interference (EMI), especially using wide bandgap devices. Instead, current-source converters (CSCs) are attracting increasing attention in recent years owing to their friendliness to short-circuit faults, improved EMI, etc. For CSCs, overvoltage is the most catastrophic failure since the semiconductor devices can hardly withstand an overvoltage for a short pulse. In this paper, a fast-response high-accuracy overvoltage protection (OVP) circuit is proposed to protect CSCs from overvoltage damage. It also features a small form factor, good noise-immunity, friendly retrofit capability, and no need for active switches. In this paper, the operating principle and design guideline of the proposed OVP circuit is introduced. Its effectiveness is validated in soft-switching solid-state transformer (S4T) at 500 V. In experiments, the voltage detection error of less than 5% and a propagation delay of fewer than 400 ns have been achieved.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS1982

Comparison of advanced thermal and electrical storage for parabolic dish solar thermal power systems

Parabolic dish solar concentrator cluster concepts are explored, with attention given to thermal storage systems coupled to Stirling and Brayton cycle power conversion devices. Sensible heat storage involving molten salt (NaOH), liquid sodium, and solid cordierite bricks are considered for 1500 F thermal storage systems. Latent heat storage with NaF-MgF2 phase change materials are explored in terms of passive, active, and direct contact designs. Comparisons are made of the effectiveness of thermal storage relative to redox, Na-S, Zn-Cl, and Zn-Br battery storage systems. Molten lead trickling down through a phase change eutectic, the NaF-MgF2, formed the direct contact system. Heat transport in all systems is effected through Inconel pipes. Using a cost goal of 120-150 mills/kWh as the controlling parameter, sensible heat systems with molten salts transport with either Stirling or Brayton engines, or latent heat systems with Stirling engines, and latent heat-Brayton engine with direct contact were favored in the analyses. Battery storage systems, however, offered the most flexibility of applications.

Fujita, T.↗

NASA NTRS1994

Infrared spectra of crystalline phase ices condensed on silicate smokes at T less than 20 K

Infrared spectra of H2O, CH3OH, and NH3 condensed at T less than 20 K on amorphous silicate smokes reveal that predominantly crystalline phase ice forms directly on deposit. Spectra of these molecules condensed on aluminum substrates at T less than 20 K indicate that amorphous phase ice forms. On aluminum, crystalline phase H2O and CH3OH are formed by annealing amorphous deposits to 155 K and 130 K, respectively (or by direct deposit at these temperatures); crystalline NH3 is formed by direct deposit at 88 K. Silicate smokes are deposited onto aluminum substrates by evaporation of SiO solid or by combustion of SiH4 with O2 in flowing H2 followed by vapor phase nucleation and growth. Silicate smokes which are oxygen-deficient may contain active surface sites which facilitate the amorphous-to-crystalline phase transition during condensation. Detailed experiments to understand the mechanism are currently in progress. The assumption that amorphous phase ice forms routinely on grains at T less than 80 K is often used in models describing the volatile content of comets or in interpretations of interstellar cloud temperatures. This assumption needs to be reexamined in view of these results.

Moore, Marla H.↗

NASA NTRS2004

Advanced Video Guidance Sensor Development Testing

Howard, Richard T.↗

NASA NTRS2004

Advanced Video Guidance Sensor (AVGS) Development Testing

NASA's Marshall Space Flight Center was the driving force behind the development of the Advanced Video Guidance Sensor, an active sensor system that provides near-range sensor data as part of an automatic rendezvous and docking system. The sensor determines the relative positions and attitudes between the active sensor and the passive target at ranges up to 300 meters. The AVGS uses laser diodes to illuminate retro-reflectors in the target, a solid-state camera to detect the return from the target, and image capture electronics and a digital signal processor to convert the video information into the relative positions and attitudes. The AVGS will fly as part of the Demonstration of Autonomous Rendezvous Technologies (DART) in October, 2004. This development effort has required a great deal of testing of various sorts at every phase of development. Some of the test efforts included optical characterization of performance with the intended target, thermal vacuum testing, performance tests in long range vacuum facilities, EMI/EMC tests, and performance testing in dynamic situations. The sensor has been shown to track a target at ranges of up to 300 meters, both in vacuum and ambient conditions, to survive and operate during the thermal vacuum cycling specific to the DART mission, to handle EM1 well, and to perform well in dynamic situations.

Howard, Richard T.↗

NASA NTRS2005

Simulation and ground testing with the Advanced Video Guidance Sensor

The Advanced Video Guidance Sensor (AVGS), an active sensor system that provides near-range 6-degree-of-freedom sensor data, has been developed as part of an automatic rendezvous and docking system for the Demonstration of Autonomous Rendezvous Technology (DART). The sensor determines the relative positions and attitudes between the active sensor and the passive target at ranges up to 300 meters. The AVGS uses laser diodes to illuminate retro-reflectors in the target, a solid-state imager to detect the light returned from the target, and image capture electronics and a digital signal processor to convert the video information into the relative positions and attitudes. The development of the sensor, through initial prototypes, final prototypes, and three flight units, has required a great deal of testing at every phase, and the different types of testing, their effectiveness, and their results, are presented in this paper, focusing on the testing of the flight units. Testing has improved the sensor's performance.

Howard, Richard T.↗

NASA NTRS2008

Hydrogen Research for Spaceport and Space-Based Applications: Fuel Cell Projects

The activities presented are a broad based approach to advancing key hydrogen related technologies in areas such as fuel cells, hydrogen production, and distributed sensors for hydrogen-leak detection, laser instrumentation for hydrogen-leak detection, and cryogenic transport and storage. Presented are the results from research projects, education and outreach activities, system and trade studies. The work will aid in advancing the state-of-the-art for several critical technologies related to the implementation of a hydrogen infrastructure. Activities conducted are relevant to a number of propulsion and power systems for terrestrial, aeronautics and aerospace applications. Fuel cell research focused on proton exchange membranes (PEM), solid oxide fuel cells (SOFC). Specific technologies included aircraft fuel cell reformers, new and improved electrodes, electrolytes, interconnect, and seals, modeling of fuel cells including CFD coupled with impedance spectroscopy. Research was conducted on new materials and designs for fuel cells, along with using embedded sensors with power management electronics to improve the power density delivered by fuel cells. Fuel cell applications considered were in-space operations, aviation, and ground-based fuel cells such as; powering auxiliary power units (APUs) in aircraft; high power density, long duration power supplies for interplanetary missions (space science probes and planetary rovers); regenerative capabilities for high altitude aircraft; and power supplies for reusable launch vehicles.

Anderson, Tim↗

NASA NTRS2013

Thermal Control Using Liquid-Metal Bridge Switches

A short term effort (3-months) was undertaken to demonstrate the feasibility of a novel method to locally control the heat transfer rate and demonstrate the potential to achieve a turndown ratio of approximately 10:1. The technology had to be demonstrated to be at a TRL of 2-3, with a plan to advance it to a TRL 5-6. Here, we show that the concept recently developed in our laboratory, namely the pinned-contact, double droplet switch made by overfilling a hole drilled in a suitable substrate can be implemented with a low-melting temperature metal. When toggled near a second substrate, a liquid bridge can be reversibly connected or disconnected, on demand. We have shown experimentally that liquid-metal bridge switches can be made from gallium with a suitable choice of substrate materials, activation strategies, and control techniques. Individual as well as arrays of gallium bridge switches were shown to be feasible and can be robustly controlled. The very short response time of the bridge connection and disconnection (on the order of 1 millisecond) provides for utility in a wide range of applications. The liquid bridge switches may be controlled actively or passively. We have shown through computations and analysis that liquid bridge switches provide locally large turndown ratios (on the order of 103:1), so a relatively sparse packing of them would be needed to obtain the desired turndown ratio of 10:1. For the laboratory demonstrations, pressure activation was utilized. Simple designs for a passive control strategy are presented which are highly attractive for several reasons, including i) large turndown ratio, ii) no solid-moving parts, and iii) stable operation. Finally, we note that passive systems do not require any electronics for their control. This along with the relatively small molecular weight of candidate materials for the system, makes for a robust design outside of Earth?s magnetic field, where spacecraft are subject to significant radiation bombardment.

Hirsa, Amir H.↗

NASA NTRS2022

Hydrocarbon Burn Facility, SWMU 007 PER- and Polyfluoroalkyl Substances (PFAS) Assessment report Addendum Kennedy Space Center, Florida

This document discusses the Per-and Polyfluoroalkyl Substances (PFAS) assessment activities performed from December 2020 through November 2021 at the Hydrocarbon Burn Facility (HBF) located at Kennedy Space Center (KSC), Florida. The HBF site has been designated Solid Waste Management Unit (SWMU) 007 under KSC’s Resource Conservation and Recovery Act (RCRA) Corrective Action Program. This PFAS Assessment Report Addendum (ARA) was prepared by Tetra Tech, Inc., for the National Aeronautics and Space Administration (NASA) under Indefinite Delivery Indefinite Quantity (IDIQ) Contract 80KSC019D0011-80KSC019F0077.

Jennifer M. Buel↗

DOE OSTI2021

Solid-State Synthesis of Highly Dispersed Nitrogen-Coordinated Single Iron Atom Electrocatalysts for Proton Exchange Membrane Fuel Cells

Fe–N–C with atomically dispersed Fe single atoms is the most promising candidate to replace platinum for the oxygen reduction reaction (ORR) in fuel cells. However, the conventional synthesis procedures require quantities solvents and metal precursors, sluggish adsorption process, and tedious washing, resulting in limited metal doping and uneconomical for large-scale production. Here, for the first time, Fe 2 O 3 is adopted as the Fe precursor to derive abundant single Fe atoms dispersed on carbon surfaces. The Fe–N–C catalyst synthesized by this simple method shows an excellent ORR activity with half-wave potentials of 0.82 and 0.90 V in acidic and alkaline solutions, respectively. A single fuel cell with an optimized Fe–N–C cathode shows a high peak power density of 0.84 W cm –2 . The solid-state transformation synthesis method developed in this study may shed light on mass production of single-atom-based catalysts.

25 ENERGY STORAGE↗

DOE OSTI2026

Infrared triggered dwell and active cooling thermal control effects on microstructural uniformity in DED

Directed Energy Deposition (DED) offers rapid large scale fabrication, but difficulty in delivering consistent microstructures and properties hinders the use of DED fabricated components in safety or performance critical applications. Variability stems from the complex thermal cycles generated by the toolpath used to print the required geometry. Several practical methods have become established in DED to regulate overheating, such as active cooling of the baseplate structure or the use of an infrared camera to inject interlayer pauses to ensure the top layer of the component cools to a set temperature, which have been shown to affect microstructure. However, no critical assessment has been performed as to how effective these controls are in promoting microstructural uniformity in the context of complex layer timing commonly generated by non-prismatic geometries. Here we show how controls influence the thermal field, phase transformations, and dynamic annealing of a low-temperature transformation steel using infrared imaging and operando neutron diffraction. Counterintuitively, common thermal homogenization process controls can reduce microstructural uniformity because these approaches stabilize peak temperature while overlooking temperatures near the solid-state phase transformation fronts. Instead, the cyclic reheating induces spatially-variant dynamically annealed regions which can be modulated via control parameters. We show that these controls have spatially linked effects centimeters away from the active weld, which implies that microstructure control must co-optimize thermal input across many subsequent layers. In conclusion, our results demonstrate the pressing need for higher order controls that integrate predictive elements of simulation data to stabilize printed properties for future qualification of DED components.

Directed energy deposition↗

NASA NTRS1992

Interactions of atomic oxygen with material surfaces in low Earth orbit: Preliminary results from experiment A0114

The atomic oxygen experiment consisted of two trays (one-sixth of a Long Duration Exposure Facility (LDEF) tray each) of 64 one inch diameter solid samples. It was intended that the effects of atomic oxygen and solar ultraviolet irradiation on the surface properties of each material could be distinguished from each other and from the effects of aging. Sixteen of the samples were placed on a thermally isolated plate of highly polished aluminum, while the main plate was coated with the thermal control coating S13-GLO. Though the experiment was entirely passive, it was hoped that the effects of thermal activation might be observed, if present. The plates were expected to stabilize at temperatures differing by 20-30 C. The samples included thin films of metals Os, Ir, Pt, Ni, Mo, and Al coated onto silica optical flats, metal carbides (WC, SiC), solid carbons of various types, eight polymers, and some other coatings of various types. Analysis is essentially complete using stylus profilometry with high sensitivity Talystep and lower sensitivity Talysurf machines. Though the integrated fluence of O atoms on the LDEF was 30 times that of previous missions, etch depths of the polymers such as the polyimide Kapton show excellent agreement with extrapolations from previous flight data. However, some new effects were observed. We demonstrated on a previous experiment on STS-8 that profilometry of this kind can show steps of 50 A (for example those due to oxide film growth on metals) and this is now the preferred method for estimating etch depth (or mass loss) of erodible substances.

Gregory, John C.↗

DOE OSTI2022

Twisted A-D-A Type Acceptors with Thermally-Activated Delayed Crystallization Behavior for Efficient Nonfullerene Organic Solar Cells

We report that molecular aggregation and crystallization during film coating play a crucial role in the realization of high-performing organic photovoltaics. Strong intermolecular interactions and high solid-state crystallinity are beneficial for charge transport. However, fast crystallization during thin-film drying often limits the formation of the finely phase-separated morphology required for efficient charge generation. Herein, the authors show that twisted acceptor-donor-acceptor (A-D-A) type compounds, containing an indacenodithiophene (IDT) electron-rich core and two naphthalenediimide (NDI) electron-poor units, leads to formation of mostly amorphous phases in the as-cast film, which can be readily converted into more crystalline domains by means of thermal annealing. This design strategy solves the aforementioned conundrum, leading to an optimal morphology in terms of reduced donor/acceptor domain-separation sizes (ca. 13 nm) and increased packing order. Solar cells based on these acceptors with a PBDB-T polymer donor show a power conversion efficiency over 10% and stable morphology, which results from the combined properties of desirable excited-state dynamics, high charge mobility, and optimal aggregation/crystallization characteristics. These results demonstrate that the twisted A-D-A motif featuring thermally-induced crystallization behavior is indeed a promising alternative design approach toward more morphologically robust materials for efficient organic photovoltaics.

14 SOLAR ENERGY↗

DOE OSTI2024

A Fluoride-Rich Solid-Like Electrolyte Stabilizing Lithium Metal Batteries

To address the problems associated with Li metal anodes, a fluoride-rich solid-like electrolyte (SLE) that combines the benefits of solid-state and liquid electrolytes is presented. Its unique triflate-group-enhanced frame channels facilitate the formation of a functional inorganic-rich solid electrolyte interphase (SEI), which not only improves the reversibility and interfacial charge transfer of Li anodes but also ensures uniform and compact Li deposition. Furthermore, these triflate groups contribute to the decoupling of Li + and provide hopping sites for rapid Li + transport, enabling a high room-temperature ionic conductivity of 1.1 mS cm -1 and a low activation energy of 0.17 eV, making it comparable to conventional liquid electrolytes. Consequently, Li symmetric cells using such SLE achieve extremely stable plating/stripping cycling over 3500 h at 0.5 mA cm -2 and support a high critical current up to 2 mA cm -2 . Here, the assembled Li||LiFePO 4 solid-like batteries exhibit exceptional cyclability for over 1 year and a half, even outperforming liquid cells. Additionally, high-voltage cylindrical cells and high-capacity pouch cells are demonstrated, corroborating much simpler processibility in battery assembly compared to all-solid-state batteries.

25 ENERGY STORAGE↗

DOE OSTI2025

The Impact of Catalyst Layer Composition and Structure on Performance and Durability of PEMWE Anodes

A study of various compositions of anodes for proton exchange membrane water electrolysis aimed at reducing precious metal content and system costs without compromising performance and durability is presented. A key challenge in current water electrolysis technologies is the reliance on high iridium loadings to ensure sufficient catalytic activity, electronic conductivity, and durability for the oxygen evolution reaction. To address this, catalyst layers based on the stable but kinetically limited rutile phase of iridium oxide are combined with platinum nanoparticles and carbon-based additives to improve structural properties and ink processability. By systematically varying the volume ratios of carbon to precious metals and ionomer to solids, compositional trends have been identified, and significant performance improvements have been achieved. Structural and elemental analysis confirms improved dispersion of platinum and iridium can be achieved, as well as electronic conductivity improvements within the catalyst layer. Polarization curve analysis has shown the ability of added Pt and C to significantly increase catalytic activity. These results highlight the potential positive impact of Pt and C on anode structure, composition, and cell performance.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Antineoplastic activity of Salmonella Typhimurium outer membrane nanovesicles

Highlights: • ST-OMVs is a promising antitumor monotherapy or as an adjuvant to chemotherapies. • ST-OMVs downregulated Ki-67 and upregulated CD49b immune-expression. • ST-OMVs downregulated angiogenesis by inhibiting VEGF gene expression. • ST-OMVs increased tumor cells apoptosis and autophagy (increased caspase-3and Beclin1). Nano-sized Gram-negative bacterial outer membrane vesicles possess unique structural and immunostimulatory effects that could be exploited to regress tumors by alerting the host immune system and reversing the immunosuppressive tumor microenvironment. The current study was conducted to investigate the antitumor activity of the outer membrane vesicles (ST-OMVs) of Salmonella Typhimurium ATCC 14028, in vitro in human colorectal carcinoma (HTC116), breast cancer (MCF-7), and hepatocellular carcinoma (HepG2) cell lines and in vivo in Ehrlich solid carcinoma-bearing mice model either as a mono-immunotherapy or as an adjuvant to a commonly used conventional chemotherapy. In addition, we investigated the safety of ST-OMVs. Adult Swiss albino female mice with transplanted Ehrlich solid carcinoma were treated with either ST-OMVs, paclitaxel or a combination of both. Tumor volume, growth inhibition rate, quantitative RT-PCR of Bax and VEGF genes expression, histopathology and immune-expression of caspase-3, Beclin-1, CD49b and Ki-67 were all analyzed. Our results showed that ST-OMVs significantly decreased tumor volume, significantly increased tumor growth inhibition rate, up-regulated the immunohistochemical expression of caspase-3, Beclin-1, and CD49b (enhanced recruitment of NK cells). Furthermore, ST-OMVs down-regulated the expression of Ki-67, increased Bax gene expression and decreased VEGF gene expression as detected by qRT-PCR analysis. Histologically, ST-OMVs promoted apoptosis, decreased tumor invasion and mitotic activities. Moreover, ST-OMVs showed a remarkable cytotoxic activity in various investigated in vitro cancer cell lines. Our findings demonstrate potential antitumor activity of ST-OMVs that might be used as a promising safe antitumor immunotherapy or an adjuvant to conventional chemotherapeutic drugs, resolving some of their problems.

60 APPLIED LIFE SCIENCES↗