Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TUBES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Fatigue Testing of Metallurgically-Bonded EBR-II Superheater Tubes

Fatigue crack growth and impact tests were performed on 2¼Cr-1Mo steel specimens machined from ex-service Experimental Breeder Reactor – II (EBR-II) superheater duplex tubes. The tubes had been metallurgically bonded with a 100 µm thick Ni layer; the specimens incorporated this bond layer. Impact tests were performed at temperatures from –50 to 400°C; cracks propagating from the V-notch were arrested by delamination at the bond layer for all tests with one exception at –50°C. Fatigue crack growth tests were performed at room temperature in air and at 400°C in air and humid Ar; cracks were grown at varied levels of constant ?K. In all conditions the presence of the Ni bond layer was found to result in a net retardation of growth as the crack passed through the layer. The mechanism of retardation was identified as a disruption of crack planarity and uniformity after passing through the porous bond layer. Full crack arrest was only observed in a single test performed at near-threshold ?K level (12 MPa?m) at 400°C. In this case the crack tip was blunted by oxidation of the base steel at the steel-nickel interface.

36 MATERIALS SCIENCE↗

Nano-cavities observed in a 316SS PWR Flux Thimble Tube Irradiated to 33 and 70 dpa

The radiation-induced microstructure of a cold-worked 316SS flux thimble tube from an operating pressurized water reactor (PWR) was examined. Two irradiated conditions, 33 dpa at 290ºC and 70 dpa at 315ºC were examined by transmission electron microscopy. The original dislocation network had completely disappeared and was replaced by fine dispersions of Frank loops and small nano-cavities at high densities. The latter appear to be bubbles containing high levels of helium and hydrogen. An enhanced distribution of these nano-cavities was found at grain boundaries and may play a role in the increased susceptibility of the irradiated 316SS to intergranular failure of specimens from this tube during post-irradiation slow strain rate testing in PWR water conditions.

Edwards, Danny J↗

Failure behavior of SiC/SiC composite tubes under strain rates similar to the pellet-cladding mechanical interaction phase of reactivity-initiated accidents

The mechanical response of a nuclear-grade silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composite was investigated under mechanical loading conditions mimicking the pellet-cladding mechanical interaction (PCMI) phase of a reactivity-initiated accident (RIA). In a RIA, cladding deformation and failure can be induced by the rapid thermal expansion of the nuclear fuel. A pulse-controlled modified-burst test was used to investigate RIA-like PCMI scenarios on SiC/SiC composite samples at pulse widths from 12 to 100 ms.The strain-driven nature of the cladding sample deformation was due to the rapid internal pressurization and subsequent expansion of a secondary tube. A digital-image correlation technique was used to measure strains from the speckle-painted outer surface of the tubes. The failure strains of samples tested at slower rates, such as RIA event durations of 52 and 100 ms, showed good agreement with the literature-reported values for similar composites tested at slow strain rates. Additionally, the failure strain showed good agreement with reference expansion-due-to-compression tests at slow strain rate. However, a decrease in the failure strain was determined for the fast-rate (12 ms) tests. This indicated that the failure strain of these composites might be influenced by the strain rate during RIA-like events. In conclusion, the failure strains observed in the tests corresponded to local energy depositions of approximately 50 cal/g UO 2 from hot zero power, with an initial condition of pellet–cladding gap closure prior to the event. In-pile transient testing of these concepts that would result in hoop strain due to PCMI in the range of 0.5–1.0% is recommended.

36 MATERIALS SCIENCE↗

Microstructure evolution and mechanical characterization of Nd:YAG laser beam welded titanium tubes

Highlights: • Joining of thin titanium tubes using laser beam welding. • Fusion zone exhibited coarse granular like grains with serrated and irregular boundaries. • Large spherical and irregular shape pores were observed at lower welding speeds. • Misorientation angle distribution indicated substructure boundaries along with single β grain formation from double α grains. • Fusion zone strengthened by substructure boundaries, solid solution strengthening and dislocation density. - Abstract: Grade 2 titanium tubes of outer diameter 60 mm and wall thickness 3.9 mm were effectively joined by Nd:YAG laser. The welding speed was varied in five levels (2.50, 2.75, 3.00, 3.25 and 3.50 m/min). The microstructure evolution was studied using optical microscopy and advanced characterization techniques. The bead geometry changed from parallel shape to wedge shape with increased welding speed due to changes in surface tension. The macrographs showed three zones namely fusion zone, heat affected zone (HAZ) and base metal. Coarse granular structure with irregular and serrated contours was observed in the fusion zone. Acicular α grains were observed at the extreme outer edge of the fusion zone due to rapid cooling. Spherical and irregular shaped pores were observed near the centerline of the fusion zone at lower welding speeds due to large amount of entrapped gases and downward sweeping solidification front. The grain size decreased with increased welding speed due to higher cooling rate. The misorientation angle distribution map showed three distinct regions. The increase in welding speed caused an increase in low angle boundaries and a reduction in very high angle boundaries. High density of dislocations was observed in the fusion zone due to thermal stresses caused by solidification. The microhardness of the fusion zone was recorded to be higher than base metal due to substructure boundaries, solute elements and dislocations. The increase in welding speed shifted the fracture location from fusion zone to base metal and fracture mode from brittle to ductile.

36 MATERIALS SCIENCE↗

Sealed-tube synthesis and phase diagram of Li{sub x}TiS{sub 2} (0 ≤ x ≤1)

Graphical abstract: We reported a new method to prepare Li{sub x}TiS{sub 2} (0 ≤ x ≤ 1) at 600 °C in sealed tube using Li{sub 2}S aslithium source. A schematic phase diagram of the Li{sub x}TiS{sub 2} system has been constructed based on the DTA and XRD data. - Abstract: We reported a new method to prepare Li{sub x}TiS{sub 2} (0 ≤ x ≤ 1) at 600 °C in sealed tube using Li{sub 2}S as lithium source. The Li{sub x}TiS{sub 2} samples were characterized by powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, and differential thermal analysis. The variations of the lattice parameters with lithium content x in Li{sub x}TiS{sub 2} were determined by X-ray powder diffraction analysis for both 1T and 3R phases. The phase transition between low-temperature 1T phase and high-temperature 3R phase was confirmed by the powder X-ray diffraction analysis. Based on the differential thermal analysis and X-ray diffraction results, a schematic phase diagram of the Li{sub x}TiS{sub 2} system has been constructed, providing a guideline to synthesize Li{sub x}TiS{sub 2} in 1T structure or 3R structure.

36 MATERIALS SCIENCE↗

Facile synthesis of TiO{sub 2} hierarchical tubes with enhanced photocatalytic activity

Graphical abstract: Hierarchical micro/nanostructured tubular TiO{sub 2} were prepared by impregnation-calcination method with FCT (the fluff of the chinar tree) as biological template and titanium tetrachloride as precursor. The resultant TiO{sub 2} samples possess curly tubular structure and the exterior outline of the samples look like fried dough twist. Moreover, the wall of the tube is assembled with spherical-likely nanoparticles. During the bio-inspired synthetic process, the FCT plays important roles as template and inducer for assembling the tubular micro/nanostructure. Furthermore, the resultant TiO{sub 2} exhibits favorable photocatalytic activity and good stability for degrading methyl orange under UV light irradiation. - Highlights: • The fluff of chinar tree was employed as template and inducer for preparing hierarchical micro/nanostructured tubular TiO{sub 2}. • The wall of the micro/nanostructured tubular TiO{sub 2} is assembled with spherical-likely nanoparticles. • The resultant TiO{sub 2} exhibits favorable photocatalytic activity and good recyclability. - Abstract: Hierarchical micro/nanostructured tubular TiO{sub 2} were prepared by impregnation-calcination method with FCT (the fluff of the chinar tree) as biological template and titanium tetrachloride as precursor. The resultant samples possess curly tubular structure and the exterior outline of the samples look like fried dough twist. Moreover, the wall of the tube is assembled with spherical-likely nanoparticles. Apparently in the process of preparation, the FCT played pivotal roles as substrate and inducer for assembling the curly tubular structure of micro/nanostructured TiO{sub 2}. Furthermore, the micro/nanostructured TiO{sub 2} have abundant pore structures and large surface area, which are beneficial to the improvement of photocatalytic activity. Under UV light irradiation, the as-prepared TiO{sub 2} exhibits nearly 100% photocatalytic decolorization rate in 30 min and 90% TOC (total organic carbon) degradation rate in 60 min for dye methyl orange (MO).

36 MATERIALS SCIENCE↗

Effect of tube processing methods on the texture and grain boundary characteristics of 14YWT nanostructured ferritic alloys

In this paper, texture and microstructure of tubes and plates fabricated from a nanostructured ferritic alloy (14YWT), produced either by spray forming followed by hydrostatic extrusion (Process I) or hot extrusion and cross-rolling a plate followed by hydrostatic tube extrusion (Process II) have been characterized in terms of their effects on texture and grain boundary character. Hydrostatic extrusion results in a combination of plane strain and shear deformations which generate low intensity α- and γ-fiber components of {001}<110> and {111}<110> together with a weak ζ-fiber component of {011}<211> and {011}<011>. In contrast, multi-step plane strain deformation by hot extrusion and cross-rolling of the plate leads to a strong texture component of {001}<110> together with a weaker {111}<112> component. Although the total strains are similar, shear dominated deformation leads to much lower texture indexes compared to plane strain deformations. Further, the texture intensity decreases after hydrostatic extrusion of the alloy plate formed by plane strain deformation, due to a lower number of activated slip systems during shear dominated deformation. Finally and notably, hot extruded and cross-rolled plate subjected to plane strain deformation to ~50% engineering strain creates only a modest population of low angle grain boundaries, compared to the much larger population observed following the combination of plane strain and shear deformation of ~44% engineering strain resulting from subsequent hydrostatic extrusion.

36 MATERIALS SCIENCE↗

Dynamic magnetic shield for the CLAS12 central TOF detector photomultiplier tubes

The Central Time-of-Flight detector for the Jefferson Laboratory 12-GeV upgrade is being designed with linear-focused photomultiplier tubes that require a robust magnetic shield against the CLAS12 main 5-T solenoid fringe fields of 100 mT (1 kG). Theoretical consideration of a ferromagnetic cylinder in an axial field has demonstrated that its shielding capability decreases with increasing length. This observation has been confirmed with finite element analysis using Poisson model software. Several shields composed of coaxial ferromagnetic cylinders have been studied. All difficulties caused by saturation effects were overcome with a novel dynamical shield, which utilizes a demagnetizing solenoid between the shielding cylinders. Basic dynamical shields for ordinary linear-focused 2-in. photomultiplier tubes were designed and tested both with models and experimental prototypes at different external field and demagnetizing current values. Our shield design reduces the 1 kG external axial field by a factor of 5000.

Source record↗

Characterization of a silicon photo-multiplier array with summing board as a photo-multiplier tube replacement in organic scintillator assemblies

In this work, we report on the energy, timing, and pulse-shape discrimination performance of cylindrical 5.08 cm diameter x 5.08 cm thick and 7.62 cm diameter x 7.62 cm thick trans-stilbene crystals read out with the passively summed output of three different commercial silicon photo-multiplier arrays. Our results indicate that using the summed output of an 8 x 8 array of SiPMs provides performance competitive with photo-multiplier tubes for many neutron imaging and correlated particle measurements. For a 5.08 cm diameter x 5.08 cm thick crystal read out with SensL’s ArrayJ-60035_64P-PCB, which had the best overall properties, we measure the energy resolution as 17.8 ± 0.8% at 341 keVee (σ/E), the timing resolution in the 180–400 keVee range as 236 ± 61 ps (σ), and the pulse-shape discrimination figure-of-merit as 2.21 ± 0.03 in the 230–260 keVee energy range. For a 7.62 cm diameter x 7.62 cm thick crystal read out with SensL’s ArrayJ-60035_64P-PCB, we measure the energy resolution as 21.9 ± 2.3% at 341 keVee, the timing resolution in the 180–400 keVee range as 518 ± 42 ps, and the pulse-shape discrimination figure-of-merit as 1.49 ± 0.01 in the 230–260 keVee energy range. Our findings enable many scintillator-based instruments to enjoy the size, robustness, and power benefits of silicon photo-multiplier arrays as replacement for the photo-multiplier tubes that are predominantly used today.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Finite element simulation of gap opening between cladding tube and spacer grid in a fuel rod assembly using crystallographic models of irradiation growth and creep

A physically-based crystal plasticity framework for modeling irradiation growth and creep is interfaced with the finite element code ABAQUS in order to study the contact forces and the gap evolution between the spacer grid and the cladding tube as a function of irradiation in a representative section of a fuel rod assembly. Deformation mechanisms governing the gap opening are identified and correlated to the texture-dependent material response. Thus, in the absence of coolant flow-induced vibrations, these simulations predict the contribution of irradiation growth and creep to the gap opening between the cladding tube and the springs and dimples on the spacer grid. The simulated contact forces on the springs and dimples are compared to available experimental and modeling data. Various combinations of external loads are applied on the springs and dimples to simulate fuel rods in the interior and at the periphery of the fuel rod assembly. Furthermore, we found that loading conditions representative (to a first order approximation) of fuel rods at the periphery show higher gap opening. This is in agreement with in-reactor data, where rod leakages due to the synergistic effects of gap opening and coolant flow-induced vibrations were generally found to occur at the periphery of the fuel rod assembly.

36 MATERIALS SCIENCE↗

Fracture toughness evaluation for Zr-4 clad tubing structure with pellet inserts

Applying fracture mechanics approach to spent nuclear fuel (SNF) system reliability investigation is warranted due to the inherent flaws and hydride structures existed in a SNF system after nuclear reactor operation. However, none of the existing fracture toughness data deal with fuel cladding specific geometry or spent fuel material conditions, such as cladding structure with the pellet-inserts and the associated pellet clad mechanical interactions induced mixed-mode damage mechanisms. Thus, the development of an intrinsic fracture mechanics approach that is suitable for SNF materials is needed. Due to thin wall and small dimension of clad tubing structure, the spiral notch torsion test (SNTT) method of small specimen approach was used to estimate the clad tubing structure fracture toughness. The estimated fracture toughness for Zr-4 cladding with alumina-pellet inserts are presented in this report. For SNTT samples with a short or medium crack length, between 5.4-mm and 8-mm, the estimate JIQ upon fracture initiation for the baseline Zr-4 cladding is at 50 kJ/m2 with 2-sigma uncertainty of 3.26 kJ/m2, and the associated KIQ is at 67.46 MPa√m. For SNTT samples with a long crack length, around 13-mm, the crack initialization is deviated from that of the Mode-I tensile fracture and appears to be a mixed-mode fracture of Mode I – tensile stress and Mode III – out of plane shear stress; the estimated JMQ is at 18.9 kJ/m2, the associated KMQ is at 41.4 MPa√m.

36 MATERIALS SCIENCE↗

An Interlaboratory Evaluation of Drift Tube Ion Mobility–Mass Spectrometry Collision Cross Section Measurements

Collision cross section (CCS) measurements resulting from ion mobility-mass spectrometry (IM-MS) experiments provide a promising orthogonal dimension of structural information in MS-based analytical separations. As with any molecular identifier, interlaboratory standardization must precede broad range integration into analytical workflows. In this study, we present a reference drift tube ion mobility mass spectrometer (DTIM-MS) where improvements on the measurement accuracy of experimental parameters influencing IM separations provide standardized drift tube, nitrogen CCS values (DTCCSN2) for over 120 unique ion species with the lowest measurement uncertainty to date. The reproducibility of these DTCCSN2 values are evaluated across three additional laboratories on a commercially available DTIM-MS instrument. The traditional stepped field CCS method performs with a relative standard deviation (RSD) of 0.29% for all ion species across the three additional laboratories. The calibrated single field CCS method, which is compatible with a wide range of chromatographic inlet systems, performs with an average, absolute bias of 0.54% to the standardized stepped field DTCCSN2 values on the reference system. The low RSD and biases observed in this interlaboratory study illustrate the potential of DTIM-MS for providing a molecular identifier for a broad range of discovery based analyses.

54 ENVIRONMENTAL SCIENCES↗

Constitution of Drop-Tube-Generated Coal Chars from Vitrinite- and Inertinite-Rich South African Coals

The structural transformations of coal and the resultant char morphologies are strongly dependent on the initial structure and degree of thermoplasticity achieved during coal-to-char transition. These are a function of petrographic composition, rank, particle size, and heating rate and strongly affect combustion behavior. This study compares the devolatilization and subsequent combustion behavior of an inertinite-rich (87.7% dmmf) and a vitrinite-rich (91.8% dmmf) South African coal, wet-screened to a narrow particle size distribution of 200 x 400 mesh. Pyrolysis chars were generated under rapid-heating conditions (104-105 °C/s) in a drop-tube reactor to closely resemble chars generated in pulverized combustion conditions. The inertinite-rich coal took ~ 400 ms to devolatilize in the drop-tube, compared to only ~ 240 ms for the vitrinite-rich sample. The chemical and physical structure (the constitution) of the chars were investigated through a range of chemical, physical, and optical characteristics including the maceral differences, and high ash yields. To evaluate the combustion reactivity non-isothermal burn-out profiles were obtained through thermogravimetrical analyses (TGA) in air. The vitrinite-rich char had on average 20% higher reaction rates than the inertinite-rich char under the various combustion conditions. The char samples were de-ashed with HCl and HF acid which resulted in an increase in combustion reactivity. The maximum reaction rate of the high-ash (36% ash yield) inertinite-rich char increased with 80% after de-ashing. While the vitrinite-rich char with an ash yield of 15%, had a 20% increase in reactivity after de-ashing. The ash acted as a barrier, and the removal of ash most likely increased the access to reactive surface area. The chemical and physical structures of the chars were characterized through a range of different analytical techniques to quantify the factors contributing to reactivity differences. The morphologies of the chars were characterized with SEM and optical microscopy, while quantitative information on the ordered nature of chars was obtained through XRD on de-ashed chars. The inertinite-rich coal experienced limited fluidity during heat-treatment, resulting in slower devolatilization, limited growth in crystallite height (11.8 to 12.6Å), only rounding of particle edges, and producing > 40% of mixed-dense type chars. The vitrinite-char showed more significant structural transformations; producing mostly (80%) extensively swollen crassisphere, tenuisphere, and network-type chars, and XRD showed a large increase in crystallite height (4.3 to 11.7Å). Nitrogen adsorption and small-angle X-ray scattering (SAXS) were utilized to compare the nitrogen surface areas and pore size distributions. Both chars were mostly mesoporous but the inertinite-rich char had double the average pore size, which also resulted in a larger nitrogen surface area since nitrogen can only access surface areas in larger pores. The BET surface area was 3.9 and 2.7 m2/g for the inertinite- and vitrinite-rich chars respectively. SAXS data showed that the vitrinite-rich char had 60% higher frequencies of pores in the micropore range. Helium porosimetry indicated that the inertinite-rich coal and resultant char had higher densities than the vitrinite coal and char; 1.6 and 2.0 g/cm3, compared to 1.3 and 1.9 g/cm3 (dry basis). Non-isothermal TGA burnout profiles showed the inertinite-rich char had a burnout temperature of 680°C, slightly higher than the vitrinite-rich char’s 650 °C. This, along with the peak shape and position in the burnout profiles indicate that the vitrinite-rich char has a higher reactivity. The higher reactivity is due to a combination of factors likely including less organization, grater porosity and access to the reactive site, less ash blocking, and char morphology differences.

Combustion↗

Glass tube of high dielectric constant and low dielectric loss for external electrode fluorescent lamps

A glass tube of aluminosilicate glass, with high dielectric constant K{approx}6.0 and low dielectric loss tan {delta}{approx}8.0x10{sup -4}, was investigated for the external electrode fluorescent lamps (EEFLs) of a dielectric barrier discharge. Compared with conventional EEFLs made out of borosilicate glass tubes with K{approx}(4.9-5.3) and tan {delta}{approx}(2.3-2.4)x10{sup -3}, the efficiency of the aluminosilicate EEFL increases by 15%-25% even at high luminance above 20 000 cd/m{sup 2} and the pinhole stability of the aluminosilicate EEFL also improves remarkably. In a soda-lime glass EEFL with a high dielectric loss tan {delta}{approx}7.0x10{sup -3}, the luminance and pinhole stability deteriorate even with a high dielectric constant K{approx}7.2 at room temperature, because the value of tan {delta} escalates as the temperature on the external electrode increases due to the dielectric heat dissipation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Simultaneous Modeling of Waveforms Associated With Backscattered He-Ne Laser Light from a Fluid Filled Capillary Tube by Use of Geometrical Optics and Wave Theories

Backscattered He-Ne laser light from a side illuminated fluid-filled fused silica capillary tube generates a series of fringes when viewed in an imaging plane. The light intensity variation as a function of scattering angle constitutes a waveform, which contains hills and valleys. Geometrical Optics and Wave Theories, simultaneously, are employed to model the waveforms and quantify the index of refraction of fluid in the capillary tube.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Performance of a Compact Gamma Tube Interrogation Source

Active interrogation with high-energy monoenergetic gammas can induce photofission signals in fissile materials while minimizing absorbed radiation dose and background from surrounding materials. A first-generation axial-type gamma generator has been developed that utilizes the {sup 11}B(p,{gamma}){sup 12}C nuclear reaction at a 163 keV resonance to produce monoenergetic 12-MeV gamma-rays. The gamma tube employs a water-cooled cylindrical radio frequency (if) induction ion source capable of producing a proton current density of up to 100 mA/cm{sup 2}. The extracted proton beam bombards a lanthanum hexaboride (LaB{sub 6}) target at energies up to 200 keV. The 12-MeV gamma intensity was measured as a function of proton energy, beam current, and angle. Photofission-induced neutrons from depleted uranium (DU) were measured and compared to MCNPX calculations. After extended operation, the high power density of the proton beam was observed to cause damage to the LaB{sub 6} target and the gamma tube improvements currently being made to mitigate this damage are discussed.

07 ISOTOPE AND RADIATION SOURCES↗

Flux Tube Profiles at High Temperature

In this work we have studied gluon field distributions around a static qq-bar pair at high temperature by means of lattice simulations of Quantum Chromodynamics in the quenched approximation. Measuring the electric and magnetic components of the gluon field at temperatures close to the critical temperature of the phase transition from the confined to the deconfined phase of QCD, we were able to see how longitudinal and transverse profiles of the flux tube between the static qq-bar pair change with temperature. The parallel electric field component turned out to be larger than the other three field components, which are approximately equal, at all a fixed constant qq-bar separation and temperatures. This tells us that, as at zero temperature, the force that comes from the field strength that is oriented along the axis connecting the qq-bar pair and trying to bind a quark and an antiquark together is chromo-electric. By exploring the temperature dependence of the longitudinal profiles we were able to show that the field strength distribution approaches the one of a single isolated quark when the rising temperature approaches the critical temperature. From the transverse profiles at various temperatures we further have found that the physical width of the flux tube decreases when the temperature increases.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Effects of tube diameter and chirality on the stability of single-walled carbon nanotubes under ion irradiation

Using molecular dynamics method, we investigated the influence of tube diameter and chirality on the stability of single-walled carbon nanotubes (CNTs) under ion irradiation. We found that in the energy range below 1 keV, the dependence of CNT stability on the tube diameter is no longer monotonic under C ion irradiation, and the thinner (5, 5) CNT may be more stable than the thicker (7, 7) CNT, while under Ar irradiation, the CNT stability increases still monotonically with the CNT diameter. This stability behavior was further verified by the calculations of the threshold ion energies to produce displacement damage in CNTs. The abnormal stability of thin CNTs is related to their resistance to the instantaneous deformation in the wall induced by ion pushing, the high self-healing capacity, as well as the different interaction properties of C and Ar ions with CNT atoms. We also found that under ion irradiation the stability of a zigzag CNT is better than that of an armchair CNT with the same diameter. This is because of the bonding structure difference between the armchair and the zigzag CNTs with respect to the orientations of graphitic networks as well as the self-healing capacity difference.

36 MATERIALS SCIENCE↗