SEARCH · Engineering Papers

Results for “TAPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Simulation of a data archival and distribution system at GSFC

A version-0 of a Data Archive and Distribution System (DADS) is being developed at GSFC to support existing and pre-EOS Earth science datasets and test Earth Observing System Data and Information System (EOSDIS) concepts. The performance of DADS is predicted using a discrete event simulation model. The goals of the simulation were to estimate the amount of disk space needed and the time required to fulfill the DADS requirements for ingestion (14 GB/day) and distribution (48 GB/day). The model has demonstrated that 4 mm and 8 mm stackers can play a critical role in improving the performance of the DADS, since it takes, on average, 3 minutes to manually mount/dismount tapes compared to less than a minute with stackers. With two 4 mm stackers and two 8 mm stackers, and a single operator per shift, the DADS requirements can be met within 16 hours using a total of 9 GB of disk space. When the DADS has no stacker, and the DADS depends entirely on operators to handle the distribution tapes, the simulation has shown that the DADS requirements can still be met within 16 hours, but a minimum of 4 operators per shift were required. The compression/decompression of data sets is very CPU intensive, and relatively slow when performed in software, thereby contributing to an increase in the amount of disk space needed.

Bedet, Jean-Jacques↗

NASA NTRS1993

Storage media pipelining: Making good use of fine-grained media

This paper proposes a new high-performance paradigm for accessing removable media such as tapes and especially magneto-optical disks. In high-performance computing the striping of data across multiple devices is a common means of improving data transfer rates. Striping has been used very successfully for fixed magnetic disks improving overall system reliability as well as throughput. It has also been proposed as a solution for providing improved bandwidth for tape and magneto-optical subsystems. However, striping of removable media has shortcomings, particularly in the areas of latency to data and restricted system configurations, and is suitable primarily for very large I/Os. We propose that for fine-grained media, an alternative access method, media pipelining, may be used to provide high bandwidth for large requests while retaining the flexibility to support concurrent small requests and different system configurations. Its principal drawback is high buffering requirements in the host computer or file server. This paper discusses the possible organization of such a system including the hardware conditions under which it may be effective, and the flexibility of configuration. Its expected performance is discussed under varying workloads including large single I/O's and numerous smaller ones. Finally, a specific system incorporating a high-transfer-rate magneto-optical disk drive and autochanger is discussed.

Vanmeter, Rodney↗

NASA NTRS1994

Through-the-thickness tensile strength of textile composites

A series of tests was run to characterize the through-the-thickness tensile strength for a variety of composites that included 2D and 3D braids, 2D and 3D weaves, and prepreg tapes. A new test method based on a curved beam was evaluated. The through-the-thickness deformations were characterized using moire interferometry. Failures were significantly different between the 2D and 3D materials. The 2D materials delaminated between layers due to out-of-plane tensile stresses. The strength of the 2D textile composites did not increase relative to the tapes. The 3D materials failed due to the formation of radial cracks caused by high circumferential stresses along the inner radius. A circumferential crack similar to the 2D materials produced the final failure. Final failure in the 3D materials occurred at a lower bending moment than in other materials. The early failures were caused by radial crack formation rather than low through-the-thickness strength.

Jackson, Wade C.↗

NASA NTRS1994

Results of demonstration test for receiving and processing of flight data from the Space Transportation System

This report presents the methodology used for receiving, processing, and analyzing flight data from the Space Transportation System at NASA Langley Research Center (LaRC) on a near real time basis. The task was performed in October 1993 during the STS-58 mission using data from the Orbital Acceleration Research Experiment (OARE). The transmitting and receiving of OARE data on a near real time basis at LaRC were highly successful. The time to receive and record the data from the payload tape recorder required 20 to 30 minutes. Payload tape recorder data were downlinked at intervals of 4 to 6 hours rather than continuously. The quality check of the data at LaRC required 2 minutes. Four to 5 minutes of time was required to obtain preliminary acceleration levels of the Orbiter that are within 1 micro-g of the absolute accelerations This demonstration has shown that, with operational modifications LaRC has the capability to serve as a User Operation Center for receiving and processing flight data from the Space Shuttle and Space Station.

Russell, James W.↗

NASA NTRS1994

High data rate recorder development at MIT Haystack Observatory

Current operational capabilities of tape recording for Very Long Baseline Interferometry (VLBI) at the Haystack Observatory allow 0.7 terabytes (12 hours at 128 Mb/s) of data to be stored in a 128 cu. inch volume. On-going efforts are aimed at full time 1 Gb/s operation with two 36-channel headstacks. Applications for linear digital tape recording, with suitable development of thin-film head arrays, suggest a volume density exceeding 1 TB/cu. inch to be achievable in the future.

Hinteregger, H. F.↗

NASA NTRS1994

The MAMMOTH project

On the surface MAMMOTH is a high performance 5.25-inch half-high 8mm helical scan tape drive that records a native 20 Gigabytes of data on Advanced Metal Evaporated media at a sustained throughput of 3 Megabyte per second over a high speed SCSI interface, that is scheduled for production in the second half of 1995. But it's much more than that. Inside its custom designed sheet metal enclosure lies one of the greatest technical achievements of its kind. Exabyte's strategic direction is to increase throughput and capacity while continuing to improve drive, data and media reliability to its products. MAMMOTH adheres to that direction and the description of its technical advances is described in this paper. MAMMOTH can be broken down into four main functional assemblies: high-performance integrated digital electronics, high-reliability tape transport mechanism, high-performance scanner, and advanced metal evaporated media. All this technology is packaged into a standard 5.25-inch half-high form factor that dissipates only 15 watts.

Gerchar, Tim↗

NASA NTRS1995

Physical interpretation and development of ultrasonic nondestructive evaluation techniques applied to the quantitative characterization of textile composite materials

In this Progress Report, the author describes the continuing research to explore the feasibility of implementing medical linear array imaging technology as a viable ultrasonic-based nondestructive evaluation method to inspect and characterize complex materials. Images obtained using an unmodified medical ultrasonic imaging system of a bonded aluminum plate sample with a simulated disbond region are presented. The disbond region was produced by adhering a piece of plain white paper to a piece of cellophane tape and applying the paper-tape combination to one of the aluminum plates. Because the area under the paper was not adhesively bonded to the aluminum plate, this arrangement more closely simulates a disbond. Images are also presented for an aluminum plate sample with an epoxy strip adhered to one side to help provide information for the interpretation of the images of the bonded aluminum plate sample containing the disbond region. These images are compared with corresponding conventional ultrasonic contact transducer measurements in order to provide information regarding the nature of the disbonded region. The results of this on-going investigation may provide a step toward the development of a rapid, real-time, and portable method of ultrasonic inspection and characterization based on linear array technology. In Section 2 of this Progress Report, the preparation of the aluminum plate specimens is described. Section 3 describes the method of linear array imaging. Sections 4 and 5 present the linear array images and results from contact transducer measurements, respectively. A discussion of the results are presented in Section 6.

Miller, James G.↗

NASA NTRS1993

Performance of resin transfer molded multiaxial warp knit composites

Composite materials that are subjected to complex loads have traditionally been fabricated with multidirectionally oriented prepreg tape materials. Some of the problems associated with this type of construction include low delamination resistance, poor out-of-plane strength, and labor intensive fabrication processes. Textile reinforced composites with through-the-thickness reinforcement have the potential to solve some of these problems. Recently, a relatively new class of noncrimp fabrics designated as multiaxial warp knits have been developed to minimize some of the high cost and damage tolerance concerns. Multiple stacks of warp knit fabrics can be knitted or stitched together to reduce layup labor cost. The through-the-thickness reinforcement can provide significant improvements in damage tolerance and out-of-plane strength. Multilayer knitted/stitched preforms, in conjunction with resin transfer molding (RTM), offer potential for significant cost savings in fabrication of primary aircraft structures. The objectives of this investigation were to conduct RTM processing studies and to characterize the mechanical behavior of composites reinforced with three multiaxial warp knit fabrics. The three fabrics investigated were produced by Hexcel and Milliken in the United States, and Saerbeck in Germany. Two resin systems, British Petroleum E9O5L and 3M PR 500, were characterized for RTM processing. The performance of Hexcel and Milliken quasi-isotropic knitted fabrics are compared to conventional prepreg tape laminates. The performance of the Saerbeck fabric is compared to uniweave wing skin layups being investigated by Douglas Aircraft Company in the NASA Advanced Composites Technology (ACT) program. Tests conducted include tension, open hole tension, compression, open hole compression, and compression after impact. The effects of fabric defects, such as misaligned fibers and gaps between tows, on material performance are also discussed. Estimated material and labor cost savings are projected for the Saerbeck fabric as compared to uniweave fabric currently being used by Douglas in the NASA ACT wing development program.

Dexter, H. Benson↗

NASA NTRS1993

Turbulence near thunderstorm tops

For several years, scientists at San Jose State University, NASA-Ames, and the University of Arizona have carried out cooperative research programs to understand the causes and effects of severe turbulence. The primary sources of data for this work are Digital Flight Data Recorder (DFDR) tapes from airliners that have been involved in turbulence incidents. A significant result of the analysis of these data has been the identification and quantification of the turbulence causes. Turbulence signatures include breaking Kelvin-Helmholtz waves, large amplitude mountain lee waves, turbulence in and around thunderstorms, and maneuvering. The requirements that must be met for a turbulence incident to be included in the NASA study are rather straightforward: (1) severe or greater turbulence must have been reported (usually with passenger injuries) and (2) the flight data tapes must be available. Despite these rather general criteria, and the fact that our cases are drawn from a wide geographical area over the U.S. and the Atlantic Ocean, we have found an interesting bias in our sample. Of 12 cases at cruise altitude, four were definitely associated with thunderstorms and two are suspected thunderstorm cases. The others were due to mountain waves, CAT, high level windshear/maneuvering, or to causes not yet determined. Although our sample is small, these numbers have raised several questions, not the least of which are: How pervasive is the problem of aircraft encounters with severe turbulence in or near thunderstorm tops (TNTT)? Given the available visible and radar evidence of thunderstorms, Why do such incidents occur? Can anything be done to allevaite the problem? This paper outlines some very preliminary efforts to answer these questions. In the following sections, physical and statistical characteristics of TNTT are discussed (Section 2), TNTT causes are summarized (Section 3), current recommendations for TNTT avoidance are reviewed (Section 4), and some suggestions to ameliorate the problem are given (Section 5).

Lester, Peter F.↗

NASA NTRS1995

High-Density Digital Data Storage System

High-density digital data storage system designed for cost-effective storage of large amounts of information acquired during experiments. System accepts up to 20 channels of 16-bit digital data with overall transfer rates of 500 kilobytes per second. Data recorded on 8-millimeter magnetic tape in cartridges, each capable of holding up to five gigabytes of data. Each cartridge mounted on one of two tape drives. Operator chooses to use either or both of drives. One drive used for primary storage of data while other can be used to make a duplicate record of data. Alternatively, other drive serves as backup data-storage drive when primary one fails.

Wright, Kenneth D.↗

NASA NTRS1995

Correlation between fabrication factor and superconducting properties of the Tl-and-Bi-based high-Tc superconductor

Large critical current densities (J(sub c)) were obtained in c axis oriented Tl-1 223/Ag composite tapes fabricated by spraying methods without a vacuum. Transport measurements at 77K under a zero field indicated a J(sub c) of 9 x 10(exp 4) A/sq cm and 7 x 10(exp 3) A/sq cm at 1T for the tapes fabricated by spray pyrolysis. The novel GPM method was also applied for Bi-2212/Ag PIT composite wire, and found to be very effective for improving the distribution of voids, which caused from the melt-solidifying process. The GPM showed a marked effect for obtaining homogeneous long wire. A 1 T class coil was successfully fabricated with monocore wire.

Maki, Naoki↗

NASA NTRS1996

High Temperature Superconducting Magnets with Active Control for Attraction Levitation Transport Applications

A research program, involving 3 British universities, directed at quantifying the controllability of High Temperature Superconducting (HTS) magnets for use in attraction levitation transport systems will be described. The work includes measurement of loss mechanisms for iron cored HTS magnets which need to produce a flux density of approx. 1 tesla in the airgap between the magnet poles and a ferromagnetic rail. This flux density needs to be maintained and this is done by introducing small variations of the magnet current using a feedback loop, at frequencies up to 10 Hz to compensate for load changes, track variation etc. The test magnet assemblies constructed so far will be described and the studies and modelling of designs for a practical levitation demonstrator (using commercially obtained HTS tape) will be discussed with particular emphasis on how the field distribution and its components, e.g., the component vector normal to the broad face of the tape, can radically affect design philosophy compared to the classical electrical engineering approach. Although specifically aimed at levitation transport the controllability data obtained have implications for a much wider range of applications.

Jones, Harry↗

NASA NTRS1996

Fluid Dynamic Verification Experiments on STS-70

Fluid dynamic experiments were flown on STS-70 as phase two of the engineering evaluation of the first bioreactor Engineering Development Unit (EDU#1). The phase one experiments were comparative cell cultures in identical units on earth and onboard STS-70. In phase two, two types of fluid dynamic experiments were performed. Qualitative comparisons of the basic flow patterns were evaluated with the use of 'dye' streaklines formed from alternate injections of either a mild acid or base solution into the external flow loop that was then perfused into the vessel. The presence of Bromothymol Blue in the fluid then caused color changes from yellow to blue or vice versa, indicating the basic fluid motions. This reversible change could be repeated as desired. In the absence of significant density differences in the fluid, the flow patterns in space should be the same as on earth. Video tape records of the flow patterns for a wide range of operating conditions were obtained. The second type of fluid dynamic experiment was the quantitative evaluation of the trajectories of solid beads of various densities and sizes. The beads were introduced into the vessel and the paths recorded on video tape, with the vessel operated at various rotation rates and flow perfusion rates. Because of space limitations, the video camera was placed as close as possible to the vessel, resulting in significant optical distortion. This report describes the analysis methods to obtain comparisons between the in-flight fluid dynamics and numerical models of the flow field. The methods include optical corrections to the video images and calculation of the bead trajectories for given operating conditions and initial bead locations.

Kleis, Stanley J.↗

NASA NTRS1996

Progress in defining a standard for file-level metadata

In the following narrative, metadata required to locate a file on tape or collection of tapes will be referred to as file-level metadata. This paper discribes the rationale for and the history of the effort to define a standard for this metadata.

Williams, Joel↗

NASA NTRS1996

Standard Test Methods for Textile Composites

Standard testing methods for composite laminates reinforced with continuous networks of braided, woven, or stitched fibers have been evaluated. The microstructure of these textile' composite materials differs significantly from that of tape laminates. Consequently, specimen dimensions and loading methods developed for tape type composites may not be applicable to textile composites. To this end, a series of evaluations were made comparing testing practices currently used in the composite industry. Information was gathered from a variety of sources and analyzed to establish a series of recommended test methods for textile composites. The current practices established for laminated composite materials by ASTM and the MIL-HDBK-17 Committee were considered. This document provides recommended test methods for determining both in-plane and out-of-plane properties. Specifically, test methods are suggested for: unnotched tension and compression; open and filled hole tension; open hole compression; bolt bearing; and interlaminar tension. A detailed description of the material architectures evaluated is also provided, as is a recommended instrumentation practice.

Masters, John E.↗

NASA NTRS1996

Atomic Oxygen and Space Environment Effects on Aerospace Materials Flown with EOIM-3 Experiment

Polymer materials samples mounted on a passive carrier tray were flown aboard the STS-46 Atlantis shuttle as complement to the EOIM-3 (Evaluation of Oxygen Interaction with Materials) experiment to evaluate the effects of atomic oxygen on the materials and to measure the gaseous shuttle bay environment. The morphological changes of the samples produced by the atomic oxygen fluence of 2.07 x 10(exp 20) atoms/cm(exp 2) are being reported. The changes have been verified using Electron Spectroscopy for Chemical Analysis (ESCA), gravimetric measurement, microscopic observations and thermo-optical measurements. The samples, including Kapton, Delrin, epoxies, Beta Cloth, Chemglaze Z306, silver Teflon, silicone coatings, 3M tape and Uralane and Ultem, PEEK, Victrex (PES), Polyethersulfone and Polymethylpentene thermoplastic, have been characterized by their oxygen reaction efficiency on the basis of their erosion losses and the oxygen fluence. Those efficiencies have been compared to results from other experiments, when available. The efficiencies of the samples are all in the range of E-24 g/atom. The results indicate that the reaction efficiencies of the reported materials can be grouped in about three ranges of values. The least affected materials which have efficiencies varying from 1 to 10(exp 25) g/atom, include silicones, epoxies, Uralane and Teflon. A second group with efficiency from 10 to 45(exp 25) g/atom includes additional silicone coatings, the Chemglaze Z306 paint and Kapton. The third range from 50 to 75(exp 25) includes organic compound such as Pentene, Peek, Ultem, Sulfone and a 3M tape. A Delrin sample had the highest reaction efficiency of 179(exp 25) g/atom. Two samples, the aluminum Beta cloth X389-7 and the epoxy fiberglass G-11 nonflame retardant, showed a slight mass increase.

Scialdone, John J.↗

NASA NTRS1998

DC-8 Scanning Lidar Characterization of Aircraft Contrails and Cirrus Clouds

An angular-scanning large-aperture (36 cm) backscatter lidar was developed and deployed on the NASA DC-8 research aircraft as part of the SUCCESS (Subsonic Aircraft: Contrail and Cloud Effects Special Study) program. The lidar viewing direction could be scanned continuously during aircraft flight from vertically upward to forward to vertically downward, or the viewing could be at fixed angles. Real-time pictorial displays generated from the lidar signatures were broadcast on the DC-8 video network and used to locate clouds and contrails above, ahead of, and below the DC-8 to depict their spatial structure and to help select DC-8 altitudes for achieving optimum sampling by onboard in situ sensors. Several lidar receiver systems and real-time data displays were evaluated to help extend in situ data into vertical dimensions and to help establish possible lidar configurations and applications on future missions. Digital lidar signatures were recorded on 8 mm Exabyte tape and generated real-time displays were recorded on 8mm video tape. The digital records were transcribed in a common format to compact disks to facilitate data analysis and delivery to SUCCESS participants. Data selected from the real-time display video recordings were processed for publication-quality displays incorporating several standard lidar data corrections. Data examples are presented that illustrate: (1) correlation with particulate, gas, and radiometric measurements made by onboard sensors, (2) discrimination and identification between contrails observed by onboard sensors, (3) high-altitude (13 km) scattering layer that exhibits greatly enhanced vertical backscatter relative to off-vertical backscatter, and (4) mapping of vertical distributions of individual precipitating ice crystals and their capture by cloud layers. An angular scan plotting program was developed that accounts for DC-8 pitch and velocity.

Uthe, Edward E.↗

NASA NTRS1998

Emerging Network Storage Management Standards for Intelligent Data Storage Subsystems

This paper discusses the need for intelligent storage devices and subsystems that can provide data integrity metadata, the content of the existing data integrity standard for optical disks and techniques and metadata to verify stored data on optical tapes developed by the Association for Information and Image Management (AIIM) Optical Tape Committee.

OPTICAL DATA STORAGE MATERIALS↗