Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stability boundary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
NASA NTRS1949

Aerodynamic Study of a Wing-fuselage Combination Employing a Wing Swept Back 63 Degrees : Characteristics at a Mach Number of 1.53 Including Effect of Small Variations of Sweep

Measured values of lift, drag, and pitching moment at a Mach number of 1.53 and Reynolds numbers of 0.31, 0.62, and 0.84 million are presented for a wing-fuselage combination having a wing leading-edge sweep angle of 63 degrees, an aspect ratio of 3.42, a taper ratio of 0.25, and an NACA 64A006 section in the stream direction. Data are also presented for sweep angles of 57.0 degrees, 60.4 degrees, 67.0 degrees, and 69.9 degrees. The experimentally determined characteristics were less favorable than indicated by the linear theory but the experimental and theoretical trends with sweep were in good agreement. Boundary-layer-flow tests showed that laminar boundary-layer separation was the primary cause of the differences between experiment and theory.

REYNOLDS NUMBER EFFECTS - COMPLETE WING↗
NASA NTRS1990

Some comparisons of linear stability theory with experiment at supersonic and hypersonic speed

Measurements of waves initiated by wind-tunnel sounds are obtained for both supersonic and hypersonic speed. Flat-plate experiments carried out at Mach numbers of 4.5, 3.7, and 2.4 under the condition of laminar tunnel-wall boundary layers whereby a low background fluctuation level prevailed are outlined, as well as flat-plate experiments with sound-induced waves at supersonic speeds. Experimental studies of 'natural' wave growth on sharp cones at zero angle of attack and Mach numbers near 8 are discussed. Attention is focused on experimental research needed on boundary-layer receptivity to eddy Mach-wave radiation, hypersonic speed, and the stability-transition relationship in zero-pressure-gradient layers.

Kendall, James M., Jr.↗
NASA NTRS1994

Receptivity of flat-plate boundary layer in a non-uniform free stream (vorticity normal to the plate)

Recent progress in both the linear and nonlinear aspects of stability theory has highlighted the importance of the receptivity problem. One of the most unclear aspects of receptivity study is the receptivity of boundary-layer flow normal to vortical disturbances. Some experimental and theoretical results permit the proposition that quasi-steady outer-flow vortical disturbances may trigger by-pass transition. In present work such interaction is investigated for vorticity normal to a leading edge. The interest in these types of vortical disturbances arise from theoretical work, where it was shown that small sinusoidal variations of upstream velocity along the spanwise direction can produce significant variations in the boundary-layer profile. In the experimental part of this work, such non-uniform flow was created and the laminar-turbulent transition in this flow was investigated. The experiment was carried out in a low-turbulence direct-flow wind tunnel T-361 at the Central Aerohydrodynamic Institute (TsAGI). The non-uniform flow was produced by laminar or turbulent wakes behind a wire placed normal to the plate upstream of the leading edge. The theoretical part of the work is devoted to studying the unstable disturbance evolution in a boundary layer with strongly non-uniform velocity profiles similar to that produced by outer-flow vorticity. Specifically, the Tollmien-Schlichting wave development in the boundary layer flow with spanwise variations of velocity is investigated.

Kogan, M. N.↗
NASA NTRS1979

Linearization of the boundary-layer equations of the minimum time-to-climb problem

Ardema (1974) has formally linearized the two-point boundary value problem arising from a general optimal control problem, and has reviewed the known stability properties of such a linear system. In the present paper, Ardema's results are applied to the minimum time-to-climb problem. The linearized zeroth-order boundary layer equations of the problem are derived and solved.

Ardema, M. D.↗
NASA NTRS1987

Stability theory applications to laminar-flow control

In order to design Laminar Flow Control (LFC) configurations, reliable methods are needed for boundary-layer transition predictions. Among the available methods, there are correlations based upon R sub e, shape factors, Goertler number and crossflow Reynolds number. The most advanced transition prediction method is based upon linear stability theory in the form of the e sup N method which has proven to be successful in predicting transition in two- and three-dimensional boundary layers. When transition occurs in a low disturbance environment, the e sup N method provides a viable design tool for transition prediction and LFC in both 2-D and 3-D subsonic/supersonic flows. This is true for transition dominated by either TS, crossflow, or Goertler instability. If Goertler/TS or crossflow/TS interaction is present, the e sup N will fail to predict transition. However, there is no evidence of such interaction at low amplitudes of Goertler and crossflow vortices.

Malik, Mujeeb R.↗
DOE OSTI2022

The stability of expanding reactive shocks in a van der Waals fluid

Despite the extensive literature accumulated since the pioneering works of D'yakov and Kontorovich in the 1950s, the stability of steady shocks is still an open question when realistic boundary conditions are accounted. The consideration of a supporting mechanism, which is indeed a necessary condition for shock steadiness, modifies the perturbation shock dynamics in the unstable range. The Noh problem is a suitable example to form steady expanding shocks. This configuration is of great interest to the high-energy-density-physics community because of its direct application to inertial confinement fusion and astrophysics, for which the stagnation of a supersonically converging material via an accretion shock front is ubiquitous. Here in this work, we extend the generalized Noh problem, both base-flow solution and linear stability analysis, to conditions where endothermic or exothermic transformations undergo across the shock. Within the spontaneous acoustic emission conditions found for a van der Waals gas, we find that cylindrical and spherical expanding shocks become literally unstable for sufficiently high mode numbers. Counterintuitively, the effect of exothermicity or endothermicity across the shock is found to be stabilizing or destabilizing, respectively.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Combined Precursor Engineering and Grain Anchoring Leading to MA-Free, Phase-Pure, and Stable α-Formamidinium Lead Iodide Perovskites for Efficient Solar Cells

a-Formamidinium lead iodide (a-FAPbI 3 ) is one of the most promising candidate materials for high-efficiency and thermally stable perovskite solar cells (PSCs) owing to its outstanding optoelectrical properties and high thermal stability. However, achieving a stable form of a-FAPbI 3 where both the composition and the phase are pure is very challenging. In this work, we report on a combined strategy of precursor engineering and grain anchoring to successfully prepare methylammonium (MA)-free and phase-pure stable a-FAPbI 3 films. The incorporation of volatile FA-based additives in the precursor solutions completely suppresses the formation of non-perovskite d-FAPbI 3 during film crystallization. Grains of the desired a-phase are anchored together and stabilized when 4-tert-butylbenzylammonium iodide is permeated into the a-FAPbI 3 film interior via grain boundaries. This cooperative scheme leads to a significantly increased efficiency close to 21% for FAPbI 3 perovskite solar cells. Moreover, the stabilized PSCs exhibit improved thermal stability and maintained ~90 % of their initial efficiency after storage at 50 degrees C for over 1600 hours.

14 SOLAR ENERGY↗
DOE OSTI2022

A precision test of averaging in AdS/CFT

We reconsider the role of wormholes in the AdS/CFT correspondence. We focus on Euclidean wormholes that connect two asymptotically AdS or hyperbolic regions with $\mathbb{S}$ 1 × $\mathbb{S}$ d-1 boundary. There is no solution to Einstein’s equations of this sort, as the wormholes possess a modulus that runs to infinity. To find on-shell wormholes we must stabilize this modulus, which we can do by fixing the total energy on the two boundaries. Such a wormhole gives the saddle point approximation to a non-standard problem in quantum gravity, where we fix two asymptotic boundaries and constrain the common energy. Crucially the dual quantity does not factorize even when the bulk is dual to a single CFT, on account of the fixed energy constraint. From this quantity we extract a smeared version of the microcanonical spectral form factor. For a chaotic theory this quantity is self-averaging, i.e. well-approximated by averaging over energy windows, or over coupling constants. We go on to give a precision test involving the microcanonical spectral form factor where the two replicas have slightly different coupling constants. In chaotic theories this form factor is known to smoothly decay at a rate universally predicted in terms of one replica physics, provided that there is an average either over a window or over couplings. We compute the expected decay rate for holographic theories, and the form factor from a wormhole, and the two exactly agree for a wide range of two-derivative effective field theories in AdS. This gives a precision test of averaging in AdS/CFT. Our results interpret a number of confusing facts about wormholes and factorization in AdS and suggest that we should regard gravitational effective field theory as a mesoscopic description, analogous to semiclassical mesoscopic descriptions of quantum chaotic systems.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

A new re-redistribution scheme for weighted state redistribution with adaptive mesh refinement

State redistribution (SRD) is a recently developed technique for stabilizing cut cells that result from finite-volume embedded boundary methods. SRD has been successfully applied to a variety of compressible and incompressible flow problems. When used in conjunction with adaptive mesh refinement (AMR), additional steps are needed to preserve the accuracy and conservation properties of the solution if the embedded boundary is not restricted to a single level of the mesh hierarchy. In this work, we extend the weighted state redistribution algorithm to cases where cut cells live at or near a coarse-fine interface within the domain. Here, we present numerical results that demonstrate that the algorithm is conservative when the coarse-fine interface intersects the embedded boundary. Additionally we compare the numerical solution of the Sod shock tube problem in an inclined cylinder with the analytic solution, and we compare the simulation of a shock hitting a cylindrical obstacle with experimental data. Finally we demonstrate the methodology for simulation of the multicomponent compressible Navier-Stokes equations in a piston-bowl geometry, and discuss the computational efficiency gained by not requiring the entire embedded boundary to be defined at the finest level.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Unstable twin in body-centered cubic tungsten nanocrystals

Twinning is commonly activated in plastic deformation of low stacking fault face-centered cubic (Fcc) metals but rarely found in body-centered cubic (Bcc) metals under room temperature and slow strain rates. Here, by conducting in situ transmission electron microscopy (TEM) at atomic scale, we discovered that, in stark contrast to those in most Fcc metals, a majority of deformation twins in Bcc metals are unstable and undergo spontaneously detwinning upon unloading. Such unexpected instability of Bcc twins was found to be closely related to the prevalence of the inclined twin boundaries—a peculiar structure where twin boundaries are not parallel to the twinning plane, and the degree of instability is in direct proportion to the fraction of the inclined twin boundary. This work provides significant insights into the structure and stability of deformation twins in Bcc metals.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Signatures of ambient pressure superconductivity in thin film La 3 Ni 2 O 7

Recently, the bilayer nickelate La 3 Ni 2 O 7 has been discovered as a new superconductor with transition temperature T c near 80 K under high pressure. Despite extensive theoretical and experimental work to understand the nature of its superconductivity, the requirement of extreme pressure restricts the use of many experimental probes and limits its application potential. Here, in this work, we present signatures of superconductivity in La 3 Ni 2 O 7 thin films at ambient pressure, facilitated by the application of epitaxial compressive strain. The onset T c varies approximately from 26 K to 42 K, with higher T c values correlating with smaller in-plane lattice constants. We observed the co-existence of other Ruddlesden-Popper phases within the films and dependence of transport behavior with ozone annealing, suggesting that the observed low zero resistance T c of around 2 K can be attributed to stacking defects, grain boundaries, and oxygen stoichiometry. This finding initiates numerous opportunities to stabilize and study superconductivity in bilayer nickelates at ambient pressure, and to facilitate the broad understanding of the ever-growing number of high temperature and unconventional superconductors in the transition metal oxides.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

NSTX-U theory, modeling and analysis results

Here, the mission of the low aspect ratio spherical tokamak NSTX-U is to advance the physics basis and technical solutions required for optimizing the configuration of next-step steady-state tokamak fusion devices. NSTX-U will ultimately operate at up to 2 MA of plasma current and 1 T toroidal field on axis for 5 s, and has available up to 15 MW of neutral beam injection power at different tangency radii and 6 MW of high harmonic fast wave heating. With these capabilities NSTX-U will develop the physics understanding and control tools to ramp-up and sustain high performance fully non-inductive plasmas with large bootstrap fraction and enhanced confinement enabled via the low aspect ratio, high beta configuration. With its unique capabilities, NSTX-U research also supports ITER and other critical fusion development needs. Super-Alfvénic ions in beam-heated NSTX-U plasmas access energetic particle (EP) parameter space that is relevant for both α-heated conventional and low aspect ratio burning plasmas. NSTX-U can also generate very large target heat fluxes to test conventional and innovative plasma exhaust and plasma facing component solutions. This paper summarizes recent analysis, theory and modelling progress to advance the tokamak physics basis in the areas of macrostability and 3D fields, EP stability and fast ion transport, thermal transport and pedestal structure, boundary and plasma material interaction, RF heating, scenario optimization and real-time control.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Energy transport analysis of NSTX plasmas with the TGLF turbulent and NEO neoclassical transport models

This work presents a study of plasma transport at low aspect ratio on the National Spherical Torus Experiment tokamak, where the turbulent and neoclassical energy fluxes calculated by the quasilinear Trapped Gyro Landau Fluid (TGLF) model and the multi species drift-kinetic Neoclassical solver (NEO) are validated against experimental data. The turbulent energy transport of two plasma discharges, one in the L-mode confinement regime and another in the H-mode regime, is dominated by electrostatic drift-wave instabilities, while the ion heat transport has a significant neoclassical contribution. The data analysis workflow is described in detail to understand how the variations of mapping and fitting of experimental data affect the power balance solution and subsequent flux-matching plasma profile predictions with the TGYRO solver. On average, the predicted plasma profiles are consistent with experimental data. However, the solutions are sensitive to various input parameters, including boundary conditions, and the electron-ion coupling. Linear gyrokinetic stability analysis demonstrates close agreement of the real frequencies of unstable modes between TGLF and CGYRO gyrokinetic simulations, but higher growth rates are predicted by TGLF, especially for the H-mode case. Estimates of the low-k modes' contributions to the total flux are consistent with linear stability analysis and the E × B suppression of turbulence in TGLF simulations with the SAT1 saturation model, while the SAT2 saturation model over-predicts the low-k modes' contribution in the H-mode case. Moreover, the results with SAT1 model are consistent with power balance analysis, which indicates only neoclassical ion energy fluxes inside ρ < 0.4 in the L-mode case and $\rho \unicode{x2A7D} 0.7$ in the H-mode case. The presence of multi-scale turbulence and ion-scale driven zonal flow mixing effects are also observed in TGLF scans of the electron turbulent heat flux over a range of temperature gradients and the electron-ion temperature ratio, which could explain the strong model sensitivity to variations of input parameters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Correlation of the L-mode density limit with edge collisionality

The "density limit'' is one of the fundamental bounds on tokamak operating space, and is commonly estimated via the empirical Greenwald scaling. This limit has garnered renewed interest in recent years as it has become clear that ITER and many tokamak pilot plant concepts must operate near or above the widely-used Greenwald limit to achieve their objectives. Evidence has also grown that the Greenwald scaling - in its remarkable simplicity - may not capture the full complexity of the disruptive density limit. In this study, we assemble a multi-machine database to quantify the effectiveness of the Greenwald limit as a predictor of the L-mode density limit and identify alternative stability metrics. We find that a two-parameter dimensionless boundary in the plasma edge, $\nu_{*\rm, edge}^{\rm limit} = 3.0 \beta_{T,{\rm edge}}^{-0.4}$, achieves significantly higher accuracy (true negative rate of 97.7\% at a true positive rate of 95\%) than the Greenwald limit (true negative rate 86.1\% at a true positive rate of 95\%) across a multi-machine dataset including metal- and carbon-wall tokamaks (AUG, C-Mod, DIII-D, and TCV). The collisionality boundary presented here can be applied for density limit avoidance in current devices and in ITER, where it can be measured and responded to in real time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Zonal magnetic fields regulate nonlinear edge-localized-mode dynamics via self-consistent force balance

Edge-localized modes (ELMs) eject intense bursts of heat and particles that threaten plasma-facing components in fusion reactors. Nonlinear full-torus BOUT++ simulations show that turbulence-driven zonal magnetic fields (ZMFs) play an essential role in nonlinear ELM evolution by maintaining self-consistent force balance. Zonal flows mitigate the initial crash through shear but do not prevent continued radial transport. When ZMFs are self-consistently included, turbulence-driven zonal currents modify the parallel current distribution and magnetic tension and are associated with a reduction of the axisymmetric (𝑛 = 0) perturbed radial force imbalance. This coincides with a transition from convective, bursty propagation to more localized, diffusive transport. Similar behavior is observed across the regimes considered, including both resistive-ballooning and peeling-ballooning cases. Finally, associated signatures, including radial electric field shear and parallel current redistribution, provide experimentally accessible diagnostics for present devices and ITER-relevant conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

In situ ion irradiation of amorphous TiO 2 nanotubes

Understanding of structural and morphological evolution in nanomaterials is critical in tailoring their functionality for applications such as energy conversion and storage. Here, we examine irradiation effects on the morphology and structure of amorphous TiO 2 nanotubes in comparison with their crystalline counterpart, anatase TiO 2 nanotubes, using high-resolution transmission electron microscopy (TEM), in situ ion irradiation TEM, and molecular dynamics (MD) simulations. Anatase TiO 2 nanotubes exhibit morphological and structural stability under irradiation due to their high concentration of grain boundaries and surfaces as defect sinks. On the other hand, amorphous TiO 2 nanotubes undergo irradiation-induced crystallization, with some tubes remaining only partially crystallized. The partially crystalline tubes bend due to internal stresses associated with densification during crystallization as suggested by MD calculations. Furthermore, these results present a novel irradiation-based pathway for potentially tuning structure and morphology of energy storage materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Assessing Strain Rate Sensitivity of Nanotwinned Al–Zr Alloys through Nanoindentation

Nanotwinned metals have exhibited many enhanced physical and mechanical properties. Twin boundaries have recently been introduced into sputtered Al alloys in spite of their high stacking fault energy. These twinned Al alloys possess unique microstructures composed of vertically aligned Σ3(112) incoherent twin boundaries (ITBs) and have demonstrated remarkable mechanical strengths and thermal stability. However, their strain rate sensitivity has not been fully assessed. A modified nanoindentation method has been employed here to accurately determine the strain rate sensitivity of nanotwinned Al–Zr alloys. The hardness of these alloys reaches 4.2 GPa while simultaneously exhibiting an improved strain rate sensitivity. The nanotwinned Al–Zr alloys have shown grain size-dependent strain rate sensitivity, consistent with previous findings in the literature. This work provides insight into a previously unstudied aspect of nanotwinned Al alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Distinct regional meteorological influences on low-cloud albedo susceptibility over global marine stratocumulus regions

Abstract. Marine stratocumuli cool the Earth effectively due to their high reflectance of incoming solar radiation and persistent occurrence. The susceptibility of cloud albedo to droplet number concentration perturbations depends strongly on large-scale meteorological conditions. Studies focused on the meteorological dependence of cloud adjustments often overlook the covariability among meteorological factors and their geographical and temporal variability. We use 8 years of satellite observations sorted by day and geographical location to show the global distribution of marine low-cloud albedo susceptibility. We find an overall cloud brightening potential for most marine warm clouds, which is more pronounced over subtropical coastal regions. A weak cloud darkening potential in the annual mean is evident over the remote SE Pacific and SE Atlantic. We show that large-scale meteorological fields from the ERA5 reanalysis data, including lower-tropospheric stability, free-tropospheric relative humidity, sea surface temperature, and boundary layer depth, have distinct covariabilities over each of the eastern subtropical ocean basins where marine stratocumuli prevail. This leads to a markedly different annual cycle in albedo susceptibility over each basin. Moreover, we find that basin-specific regional relationships between key meteorological factors and albedo susceptibilities are absent in a global analysis. Our results stress the importance of considering the geographical distinctiveness of temporal meteorological covariability when scaling up the local-to-global response of cloud albedo to aerosol perturbations.

54 ENVIRONMENTAL SCIENCES↗