Results for “Protection” — Page 69

NASA NTRSDate not supplied

Advanced TUFROC Thermal Protection System Evolution Under Re-entry like Conditions

Toughened Unipiece Fibrous Reinforced Oxidation-resistant Composite (TUFROC) and its successor, Advanced TUFROC, are state-of-the-art thermal protection systems (TPS) for high temperature reusable applications. Originally designed for use on the wing-leading edge of X-37B, TUFROC is an insulative tiled system consisting of a low-conductivity ceramic base, a carbonaceous cap, and multiple coatings for thermal performance. The improved Advanced TUFROC has demonstrated reusability up to 2900 °F and single use capabilities exceeding 3200 °F. This effort explores the evolution of Advanced TUFROC when exposed to re-entry like conditions via arc jet testing. Chemical reactions and constituent migration resulting from the aerothermal heating are known to occur and are studied in detail. Further, the interaction between the multiple constituents and layers will be discussed as this is believed to have a significant impact on the overall performance. Characterization includes structural analysis via optical microscopy, scanning electron microscopy and energy-dispersive x-ray spectroscopy.

Thermal protection system↗

NASA NTRSDate not supplied

Minimally Intrusive Single-Chip Recession/Temperature Sensors for Spacecraft Thermal Protection Systems

We report the initial results of ongoing development of minimally intrusive, single-chip integrated capacitive recession/temperature sensors that would provide real-time monitoring of ablation recession of heatshield thermal protection systems (TPS) during spacecraft atmospheric entry. This work, which was performed using Phenolic Impregnated Carbon Ablator (PICA), is also to demonstrate the ease of sensor insertion during TPS manufacturing, thereby resulting in faster, low-cost, uniform sensor assembly, and spatial distribution, without compromising TPS structural integrity. Using oxy-acetylene flame at 500 W-cm-2 heat flux for 16 seconds, the average recession depth of 3.25 mm was obtained. Some measurement problems were encountered in this first attempt. However, the initial results obtained are in relatively good agreement with published data, and offer promise of future improvement based on lessons learned.

Recession↗

NASA NTRS2023

Actively Controlled Louver for Human Spacecraft Radiator Ultraviolet (UV), Dust, and Freeze Protection

The paper examines the use of actively controlled louvers for human spacecraft radiators. State of the Art (SOA) radiators were design for Low Earth Orbit (LEO) operations where Ultraviolet (UV) radiation and dust have miniscule performance impacts. However, Artemis missions to the lunar orbit or surface will expose the radiators to high dose UV radiation and dust, which can degrade the radiator coating emissivity by up to 50% and consequently reduce performance early in missions. In addition, environmental nighttime temperatures at the lunar south pole are significantly colder and linger longer than LEO, and may require up to 4 kW of heater power to prevent coolant tubes from freezing, thawing, and rupturing. Analysis showed equipping the radiators with actively controlled louvers attenuated the UV radiation and dust effects, and limited degradation to less than 10% through End of Life (EOL) of missions. Furthermore, analysis demonstrated the ability to eliminate the heater power needed for freeze protection. Louver technology is a promising solution to maintain radiator performance and integrity for Artemis missions, but heritage louvers are passively controlled and only been used on small satellites. The technology requires maturing to active control, or motor actuated, to achieve faster thermal response times. Design considerations are discussed in this paper.

Louver↗

NASA NTRSDate not supplied

TPS Certification by Analysis: Model-Driven Characterization of Properties and Failure in Woven Thermal Protection Systems

Woven, ablative thermal protection system (TPS) materials provide a robust option for aggressive (re)entries and thus have been baselined for the upcoming Mars Sample Return (MSR) mission's Earth Entry System (EES). The reliability requirements for MSR-EES necessitate understanding of material property variability, which could be significant given the complex structure and anisotropic nature of properties in TPS weaves, as well as the response to potential impact with micrometeoroids or orbital debris during the EES re-entry. The TPS Certification by Analysis effort within the Entry Systems Modeling project seeks to provide computational models and analyses that support the certification against such material-based risks. For the present talk, focus will be given to the characterization of baseline woven TPS material properties and mechanical failure limits, which entails (1) use of computational techniques (e.g., machine learning) to interpret computed tomography images of the weave to generate representative structural models and (2) application of multiscale material modeling approaches to characterize thermomechanical and failure properties.

thermal protection systems↗

NASA NTRSDate not supplied

State of the Art Thermal Protection Systems at NASA for Outer Planet Probes and TPS Developments in Support of Mars Sample Return Mission

In the recent NASA Planetary Science Decadal Survey (2023-2032) the committee recommended that the highest scientific priority of NASA’s robotic exploration efforts this decade should be completion of Mars Sample Return (MSR) and recommended to prioritize the Uranus Orbiter and Probe as the highest-priority new flagship missions for the next decade while Saturn Probe is one of the themes still under consideration for New Frontiers. This short course presentation will discuss relevant environments for outer planet missions and TPS materials under development at NASA and their readiness to meet mission needs. In addition the presentation will discuss the status of thermal protection system for the MSR Earth Entry System that brings the Martian samples safely through the Earth’s atmosphere.

Thermal Protection Systems↗

NASA NTRSDate not supplied

Design and Testing of a Hard-Fault Protection Circuit for a 1 kV SiC MOSFET Inverter

Due to increasingly high DC link voltages and further advancements in the current density of silicon carbide (SiC) MOSFETs, it has become evident that conventional IGBT protection methods are not sufficient to prevent exceeding the current rating of these devices during low-inductance fault events. This paper explores the use of an air core Rogowski coil topology to mitigate these hard fault events. The design of this circuit resulted in safe shutdown of a low impedance phase-to-phase fault in under one microsecond, tested up to DC link voltages of 1 kV. This paper details the theory, design, simulation, and successful test results of this method.

hard fault protection↗

NASA NTRSDate not supplied

ISS External Microorganisms: Tools and Techniques for Collecting Planetary Protection Samples During Extravehicular Activity

We have designed, built, and tested a sampling kit (Fig. 1) to aseptically collect microbiological samples from exterior surfaces on the ISS (International Space Station). The kit was flown to ISS as part of the NG-19 commercial cargo mission in August of 2023. Astronauts will use the kit to collect samples from six exterior surfaces on ISS. These samples will be frozen at -80°C after collection and returned to the ground for next generation DNA sequencing. The results of this experiment will help inform planetary protection requirements for crewed missions. We hypothesize that there are detectable microbial communities outside ISS and that these communities originate from inside ISS. Current life support systems do not include any components for reducing microbial leakage. Gases are vented from inside ISS without filtration and there are currently no protocols in place to minimize bioburden on space suit exteriors prior to use. It is important to quantify the bioburden on current vehicles so that achievable limits can be set for crewed missions to astrobiologically relevant locations like Mars.

Planetary Protection↗

NASA NTRS2024

ISS External Microorganisms: A Planetary Protection Experiment to Inform Requirements for Crewed Missions to Mars

We have developed, tested, and flown a caddy capable of collecting aseptic samples from external surfaces of the ISS (International Space Station). The sampling caddy is certified for use during US EVA (extra vehicular activity) and was launched to ISS in the summer of 2023. We are scheduled to collect samples from 6 locations outside ISS during an EVA in May of 2024. We will freeze these samples at -80°C on orbit and return them to Earth. We will then extract and sequence any DNA collected during the EVA using next generation sequencing technologies to characterize the community composition and function of each sample. Measuring the type and quantity of microbes present on the exterior of ISS will allow us to address knowledge gap 2B, “Acceptable levels of microbial/organic releases from humans and support systems” described in a 2019 COSPAR report. Collecting data about microbial release from current crewed vehicles will inform requirements for acceptable leak rates for future crewed missions to Mars. The sampling kit consists of eight commercially available, sterile, DNA free, macrofoam swabs ( 23 mm. diameter ) installed in custom aluminum end effectors. Each end effector is housed in and individual aluminum canister. Each canister contains a 0.2 μm Teflon filter to allow the interior volume to accommodate pressure changes without permitting microbial contaminants to enter the sterile interior volume. A handle repurposed from the space shuttle tile repair kit is used to remove the end effector from the sample canister, collect a sample by swabbing a surface and then replace the end effector in its canister. The canisters and end effectors were cleaned and assembled on Earth. Prior to installing the sterile swab the canisters and end effectors were sterilized in an autoclave at 134°C, 215 kPA, for 7 min.. The final assembly occurred in a sterilized class II biosafety cabinet. We will collect six samples from the 1) airlock vestibule, 2) airlock thermal cover, 3) a gap in the micrometeorite shielding near the airlock, 4) a handrail near the airlock, 5) the CDRA (Carbon Dioxide Removal Assembly) vent, and 6) the VES (Vacuum Exhaust System) vent. The remaining two swabs will be reserved as controls. One swab will be exposed during the EVA without touching any surfaces to act as a blank. The final swab will remain sealed until the entire sampling kit is returned to earth. Based on previously published results from the Russian segment, we hypothesize that there will be detectable microbes at some or all of these locations. Ground-based testing of this sampling caddy confirms that the swabs remain sterile as the canisters transition in and out of vacuum. We were able to retrieve, viable bacterial and fungal cells as well as DNA from samples collected from US space suits during vacuum chamber tests lasting as long as seven hours. Based on these results and feedback from the test subjects the sampling caddy was modified to improve ergonomics and meet US EVA safety requirements. Bayonet probes were added to the sides of the sample kit as alternate mounting points. Additional locking features were added to the end effector and the filter stack to prevent inadvertent release during use. The opening mechanism was changed from one where the end effector was rocked laterally to defeat a ball detent to a twist-to-open threaded closure for similar reasons. Demonstrating, this sampling caddy’s effectiveness during a US EVA will allow us to address knowledge gaps identified in COSPAR reports and begin to define planetary protection requirements for life support systems on crewed missions to mars. This kit could also be used to collect contamination control samples during Artemis missions to verify requirements and could be easily modified for robotic sample collection.

Planetary Protection↗

NASA NTRS2024

Advanced Lightweight TUFROC Thermal Protection System for Space Plane Applications

Toughened Uni-piece Fibrous Reinforced Oxidation-resistant Composite (TUFROC) represents the state of the art in low-cost, reusable spacecraft Thermal Protection Systems (TPS) with high temperature capability and is flight proven on the USAF X-37B. The two-piece design takes advantage of a low-conductivity porous silica substrate combined with high-temperature-capable carbon cap and surface treatments. NASA has updated the chemical composition of the surface treatments resulting in improved high-heating capability and reusability. The new system, called Advanced TUFROC, experiences a lower surface temperature (by ~80 K) at identical aerothermal heating conditions compared to the original formulation, now called Standard TUFROC. The reduced heating is attributed to the lower catalytic efficiency of the new formulation, which results in reduced exothermic atom recombination rates at the surface. Multiple arc-jet test campaigns demonstrate that Advanced TUFROC has the ability to withstand long and repeated exposures at 1866 K or a shorter duration exposure at 1980 K without recession or damage to TPS. Furthermore, an improved arc-jet article design for assessing 3-dimensional flow over a wing leading edge has been developed and tested. This article allows for assessment of heating at a tile gap under flight-relevant conditions at significantly reduced article fabrication and arc-jet facility configuration costs compared to prior work.

TUFROC↗

NASA NTRSDate not supplied

ISS External Microorganisms: Collecting Planetary Protection Samples During Extravehicular Activity

We have developed, tested, and flown a caddy capable of collecting aseptic samples from external surfaces of the ISS (International Space Station). The sampling caddy is certified for use during US EVA (extra vehicular activity) and was launched to ISS in the summer of 2023. We are scheduled to collect samples from 6 locations outside ISS during an EVA in May of 2024. We will freeze these samples at -80°C on orbit and return them to Earth. We will then extract and sequence any DNA collected during the EVA using next generation sequencing technologies to characterize the community composition and function of each sample. Measuring the type and quantity of microbes present on the exterior of ISS will allow us to address knowledge gap 2B, “Acceptable levels of microbial/organic releases from humans and support systems” described in a 2019 COSPAR report. Collecting data about microbial release from current crewed vehicles will inform requirements for acceptable leak rates for future crewed missions to Mars. The sampling kit consists of eight commercially available, sterile, DNA free, macrofoam swabs ( 23 mm. diameter ) installed in custom aluminum end effectors. Each end effector is housed in and individual aluminum canister. Each canister contains a 0.2 μm Teflon filter to allow the interior volume to accommodate pressure changes without permitting microbial contaminants to enter the sterile interior volume. A handle repurposed from the space shuttle tile repair kit is used to remove the end effector from the sample canister, collect a sample by swabbing a surface and then replace the end effector in its canister. The canisters and end effectors were cleaned and assembled on Earth. Prior to installing the sterile swab the canisters and end effectors were sterilized in an autoclave at 134°C, 215 kPA, for 7 min.. The final assembly occurred in a sterilized class II biosafety cabinet. We will collect six samples from the 1) airlock vestibule, 2) airlock thermal cover, 3) a gap in the micrometeorite shielding near the airlock, 4) a handrail near the airlock, 5) the CDRA (Carbon Dioxide Removal Assembly) vent, and 6) the VES (Vacuum Exhaust System) vent. The remaining two swabs will be reserved as controls. One swab will be exposed during the EVA without touching any surfaces to act as a blank. The final swab will remain sealed until the entire sampling kit is returned to earth. Based on previously published results from the Russian segment, we hypothesize that there will be detectable microbes at some or all of these locations. Ground-based testing of this sampling caddy confirms that the swabs remain sterile as the canisters transition in and out of vacuum. We were able to retrieve, viable bacterial and fungal cells as well as DNA from samples collected from US space suits during vacuum chamber tests lasting as long as seven hours. Based on these results and feedback from the test subjects the sampling caddy was modified to improve ergonomics and meet US EVA safety requirements. Bayonet probes were added to the sides of the sample kit as alternate mounting points. Additional locking features were added to the end effector and the filter stack to prevent inadvertent release during use. The opening mechanism was changed from one where the end effector was rocked laterally to defeat a ball detent to a twist-to-open threaded closure for similar reasons. Demonstrating, this sampling caddy’s effectiveness during a US EVA will allow us to address knowledge gaps identified in COSPAR reports and begin to define planetary protection requirements for life support systems on crewed missions to mars. This kit could also be used to collect contamination control samples during Artemis missions to verify requirements and could be easily modified for robotic sample collection.

Planetary Protection↗

NASA NTRSDate not supplied

Multiscale and Multifidelity Modeling of a 3D Woven Composite Thermal Protection System

Complex three-dimensional (3D) woven composites have been considered by multiple NASA projects in recent years as a means of offering improved mechanical and thermal performance over traditional laminated composite systems. Parallel efforts have focused on developing simulation capabilities for these systems, which have traditionally and heavily relied on experimental testing to evaluate composite performance. One system is the Heatshield for Extreme Entry Environment Technology (HEEET), which is being considered for the thermal protection system on reentry spacecraft. Optical microscopy was used to characterize the blended carbon and phenolic fiber tows. A section of HEEET insulation layer was imaged with high-resolution micro-computed tomography (microCT) and segmented to separate individual tows, porous matrix, and voids. These data were used to develop multiscale thermomechanical computational models within the NASA Multiscale Analysis Tool (NASMAT). Two NASMAT modeling approaches were considered to capture the details of the 3D woven architecture: a coarse model appropriate for inclusion in multiscale structural analyses and a high-fidelity model created by downsampling the microCT data. Both elastic and thermal properties were computed and compared. The feasibility and challenges associated with modeling complex, hybrid 3D woven composites were also addressed.

NASMAT↗

NASA NTRSDate not supplied

Thermal Protection System P50 Cork Char Response Characterization to Ascent Flight Shear and Heating Environments

NASA’s Space Launch System (SLS) experienced deflagration of the acreage of the Core Stage base heat shield during the Green Run hot-fire test campaigns and Artemis I flight. The burning products from the base heat shield during Green Run hot-fire test operation led to concerns in aerothermal environments and thermal protection system (TPS) performance prior to Artemis I flight. Updated design thermal environments accounting for cork combustion were developed using Green Run measurements and assessed prior to Artemis I, resulting in increased TPS thickness for the base heat shield. This work documents a highly controlled ground test within the NASA Marshall Space Flight Center’s Propulsion Test Branch Hot Gas Facility (HGF) and investigates the P50 cork TPS response due to sensitivity changes in radiative heat rates and surface shear stress. Prior to testing at the HGF, most of the P50 cork panels had a thick layer of char due to the cork combustion process replicated in a thermal vacuum chamber. SLS ascent shear stress and heating rate profile were simulated within the HGF by running the combustion-driven wind tunnel at off-nominal conditions and Mach numbers below 1. This test data provided insight into aerothermal measurements from Artemis I flight as well as informing updated base heating design environments for Artemis II. An in-depth understanding of the TPS P50 cork char response and observations is presented for launch vehicle flight ascent environments.

aerothermodynamics↗

NASA NTRSDate not supplied

Improvements to Thermal Protection System Design of Aerocapture Systems for Uranus Orbiters

The National Academies Planetary Science and Astrobiology Decadal Survey identified Uranus and Neptune - called Ice Giants - as the priority destinations for science. The survey assessed both a mission to Uranus through the Uranus Orbiter and Probe (UOP) concept, and Neptune through the Neptune-Triton Odyssey concept and determined that Uranus is the highest priority for a Flagship class mission. The UOP mission concept planned to deliver an in situ probe and conduct a multi-year orbital tour of the system to meet the science objectives. While the Uranus mission is currently viable with launch windows starting in 2031 using existing launch vehicles, the mission has a cruise phase of at least 12 years and would require more than half of its weight in fuel propellant to achieve the change in velocity necessary for orbital insertion. Aerocapture uses aerodynamic forces generated on a vehicle by the planet's atmosphere to modulate a spacecraft's trajectory, decreasing spacecraft velocity, and allowing mission designers to target the final orbital state. Aerocapture reduces the time-of-flight from Earth to Uranus over a fully propulsive solution, opening up more launch opportunities to arrive in the 2040's to the mission's science objectives. Aerocapture also allows a payload mass increase by mitigating the need for fuel to retropropulsively insert the payload into orbit, thereby increase the science that can be performed. For an aerocapture mission structure using a traditional aeroshell to deliver the UOP scientific payload to Uranus, Conformal Phenolic Impregnated Carbon Ablator (C-PICA) was determined to be the best-performing forebody thermal protection system (TPS) and other candidate aftbody TPS options were presented as feasible. This paper focuses on A) evaluating C-PICA as a forebody TPS using stressing entry conditions associated with a large range of potential Uranus flagship launch vehicles and interplanetary trajectories, B) widening the aftbody TPS candidates for new mass-efficient and cost-efficient solutions, and C) a summary list of actions remaining to provide a technically feasible and supply-robust set of TPS for an aerocapture vehicle to the Ice Giants is presented.

C-PICA↗

NASA NTRSDate not supplied

Improvements to Thermal Protection System Design of Aerocapture Systems for Uranus Orbiters

The National Academies Planetary Science and Astrobiology Decadal Survey identified Uranus and Neptune - called Ice Giants - as the priority destinations for science. The survey assessed both a mission to Uranus through the Uranus Orbiter and Probe (UOP) concept, and Neptune through the Neptune-Triton Odyssey concept and determined that Uranus is the highest priority for a Flagship class mission. The UOP mission concept planned to deliver an in situ probe and conduct a multi-year orbital tour of the system to meet the science objectives. While the Uranus mission is currently viable with launch windows starting in 2031 using existing launch vehicles, the mission has a cruise phase of at least 12 years and would require more than half of its weight in fuel propellant to achieve the change in velocity necessary for orbital insertion. Aerocapture uses aerodynamic forces generated on a vehicle by the planet's atmosphere to modulate a spacecraft's trajectory, decreasing spacecraft velocity, and allowing mission designers to target the final orbital state. Aerocapture reduces the time-of-flight from Earth to Uranus over a fully propulsive solution, opening up more launch opportunities to arrive in the 2040's to the mission's science objectives. Aerocapture also allows a payload mass increase by mitigating the need for fuel to retropropulsively insert the payload into orbit, thereby increase the science that can be performed. For an aerocapture mission structure using a traditional aeroshell to deliver the UOP scientific payload to Uranus, Conformal Phenolic Impregnated Carbon Ablator (C-PICA) was determined to be the best-performing forebody thermal protection system (TPS) and other candidate aftbody TPS options were presented as feasible. This paper focuses on A) evaluating C-PICA as a forebody TPS using stressing entry conditions associated with a large range of potential Uranus flagship launch vehicles and interplanetary trajectories, B) widening the aftbody TPS candidates for new mass-efficient and cost-efficient solutions, and C) a summary list of actions remaining to provide a technically feasible and supply-robust set of TPS for an aerocapture vehicle to the Ice Giants is presented.

C-PICA↗

DOE OSTI2021

Novel Magnesium Pretreatment Coatings Offering Excellent Corrosion Protection

There is a growing interest in using magnesium alloys for automotive, industrial, and aerospace applications due to their low density, high strength-to-weight ratio, good machinability, and low cost. These alloys have the potential to lighten cars and aircraft, reducing fuel consumption and emissions. A major drawback to the use of magnesium alloys is their highly reactive nature, which can result in corrosion; as a result, most existing pretreatment systems for these alloys require the use of chromium, which is increasingly coming under regulatory pressures, as a corrosion inhibitor. Through a project funded by the Department of Energy and administered by the U.S. Automotive Materials Partnership (USAMP), PPG developed chromium-free metal pretreatment solutions for ZEK-100 and AZ21 magnesium alloys. In a major technical advance, several chromium-free cleaning and pretreatment processes were developed that offer excellent corrosion protection when compared to a typical automotive pretreatment systems. To expand the use cases for these systems beyond single-alloy substrates to broader multi-metal assemblies, these pretreatment solutions were also optimized for use in multi-metal applications: compatibility with magnesium and other metals was demonstrated without the need for additional process steps.

36 MATERIALS SCIENCE↗

DOE OSTI2024

What is involved in radiation protection at accelerator facilities?

Radiation protection for accelerator facilities involves a range of actions to operate the facility within safe boundaries (often called an accelerator safety envelope) and it starts from the very early stage of facility development. Each facility will establish fundamental safety principles, requirements, and measures to control the radiation exposure to people and the release of radioactive material to the environment.

61 RADIATION PROTECTION AND DOSIMETRY↗

DOE OSTI2024

Dover CoreGuard Ⓡ Cybersecurity Protections for Critical Energy Infrastructure Final Report

This report documents the status of technical objectives and activities for the Department of Energy (DOE) Small Business Innovation Research (SBIR) Phase I project, titled “Dover CoreGuard Ⓡ Cybersecurity Protections for Critical Energy Infrastructure” (Award No. DE-SC0023743), undertaken by Dover Microsystems, Inc., Wayland, MA. The Principal Investigator for this project was Dr. Stephen Papa, Dover’s Chief Technology Officer (CTO). The contract PoP (Period of Performance) is scheduled for completion by February 9, 2024.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2024

Regularized Differentiation for Bioburden Density Estimation in Planetary Protection

In this paper, we propose and investigate the performance of two novel shrinkage estimators for bioburden density estimation in planetary protection. The estimators are based on the regularized differentiation of a cumulative count of colony forming units collected throughout the data collecting session or the life cycle of the entire mission. The regularized differentiation recasts the problem of bioburden density estimation as a linear least squares problem. The least squares problem is then solved through regularization techniques, such as truncated singular value decomposition and penalized least squares. The regularization is necessary to avoid noise amplification during the differentiation of noisy data. The two regularization estimators are compared with four other commonly used estimators to simultaneously evaluate the means of multivariable independent Poisson distributions: the maximum likelihood, noninformative Bayes estimator with Jeffreys prior, Empirical Bayes using conjugate gamma-Poisson model with gamma parameters selected by method of moments, and the Clevenson-Zidek estimator. It is shown through computer-simulated data that the regularized differentiation based on ridge regression has the smallest mean-squared error among all estimators. The analysis of shrinkage mechanism implemented by regularized differentiation is performed, and it is shown that the regularized differentiation amounts to performing a weighted averaging of all the samples. The weights are determined by the regularization parameter automatically selected by the L-curve technique. Since the method of least squares makes no distributional assumptions about the data, it presents an attractive technique for bioburden density estimation when there are concerns about the misspecification of the distributional model. The paper concludes with the analysis of the bioburden data collected during InSight mission and directions for future work.

97 - MATHEMATICS AND COMPUTING↗