Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Power system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Algorithm development for a spacecraft autonomous power system

Two algorithms were developed to demonstrate the implementation of autonomous functions in an existing spacecraft power system. The functions selected for autonomous operation include a typical performance monitoring function, battery state of charge, and a fault detection and response function represented by a battery state of charge below a preselected limit. The constraints imposed by the existing power system configuration are the available data in the telemetry stream and the existing commands and command structure. The areas requiring future development are the degree of battery characterization, the effects of hardware/software faults, and the verification of faults.

Bridgeforth, A. O.↗

A New Model of Frequency Delay in Power Systems

Observations of slow frequency signals in power systems have been explained by continuum wave equations that approximate the system's electromechanical dynamics. These continuum models predict that the signal speed is a function of the rotational inertia of the generators and impedances of the transmission lines. Here, we show that frequency signals with speeds modulated by these factors are predicted by the swing and Kirchhoff equations, without resorting to a continuum model. Our analysis also shows that the precision of the sensors used to measure frequency has a significant impact on the apparent speed of the frequency signal.

24 POWER TRANSMISSION AND DISTRIBUTION↗

A scalable mixed-integer decomposition approach for optimal power system restoration

The optimal restoration problem lies at the foundation of the evaluation and improvement of resilience in power systems. In this paper we present a scalable decomposition algorithm, based on the integer L-shaped method, for solving this problem for realistic power systems. The algorithm works by partitioning the problem into a master problem and a slave problem. The master problem optimizes over energization sequences of generators, buses and branches, for the entire restoration horizon, while respecting stylized energization requirements. The slave problem verifies that there exist power flow solutions supporting the energization sequences proposed by the master problem, adding cuts to the master if an infeasible sequence is detected. The power flow verification is carried out using a piece-wise linear approximation of the power flow equations, capable of capturing overvoltage situations common in restoration procedures. We develop specialized binary cuts and hybrid Benders-binary cuts for separating infeasible islands, which are stronger than regular no-good cuts, as well as heuristics for obtaining feasible solutions. We present numerical results for the IEEE 39- and 118-bus systems, and for the Chilean 1500-bus grid, where our algorithm finds near-optimal restoration sequences orders of magnitude faster than the state-of-the-art, demonstrating the effectiveness of the proposed approach.

24 POWER TRANSMISSION AND DISTRIBUTION↗

AC power system breadboard

The object of this program was to design, build, test, and deliver a high-frequency (20-kHz) Power System Breadboard which would electrically approximate a pair of dual redundant power channels of an IOC Space Station. This report describes that program, including the technical background, and discusses the results, showing that the major assumptions about the characteristics of this class of hardware (size, mass, efficiency, control, etc.) were substantially correct. This testbed equipment has been completed and delivered to LeRC, where it is operating as a part of the Space Station Power System Test Facility.

Wappes, Loran J.↗

Suppression of Weakly-Damped Torsional Oscillations in Autonomous Power Systems

Variants are considered for suppression of weakly-damped vibration effects caused by the first critical frequency of torsional oscillations of a gas-turbine unit in the autonomous electric power system of an oil and gas field. It is shown that torsional oscillations can be suppressed with the aid both of a reactive power source installed at the field power system, consisting of a controlled shunt reactor (CSR) and a static capacitor battery, and of an auxiliary active RLC filter, when using in both cases auxiliary control loops of torsional deviation as well as its first and second derivatives. A methodology has been developed for simultaneous coordination of the settings of any regulation system based on a numerical optimization, which permits selecting the characteristics of control loops of the source of reactive power and active RLC filter that are optimal from the point of view of suppressing torsional oscillations.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Physics-informed graphical neural network for power system state estimation

State estimation is highly critical for accurately observing the dynamic behavior of the power grids and minimizing risks from cyber threats. However, existing state estimation methods encounter challenges in accurately capturing power system dynamics, primarily because of limitations in encoding the grid topology and sparse measurements. Here, this paper proposes a physics-informed graphical learning state estimation method to address these limitations by leveraging both domain physical knowledge and a graph neural network (GNN). We employ a GNN architecture that can handle the graph-structured data of power systems more effectively than traditional data-driven methods. The physics-based knowledge is constructed from the branch current formulation, making the approach adaptable to both transmission and distribution systems. The validation results of three IEEE test systems show that the proposed method can achieve lower mean square error more than 20% than the conventional methods.

43 PARTICLE ACCELERATORS↗

Advanced Modular Power System Electronics Enclosure Thermal Testing

An analysis was set up to model the temperature of the advanced modular power system (AMPS) power distribution cards when installed within the electronics enclosure case. The analysis was used to determine the steady-state temperature distribution of the cards within the case. To verify the analysis, an experiment was set up and conducted to simulate the operation of the cards within the enclosure. Four tests were conducted. The tests varied the position of the cold plate and evaluated the use of a thermal compound to reduce the contact resistance between the joints within the thermal path between the cards and the cold plate. Three of the four cases examined showed very good agreement between the analysis and the experiment with a less than 1-percent variation in the predicated temperatures determined through the analysis and the experimentally derived temperatures. In the remaining case, the difference between the analysis and experiment was approximately 12 percent. Both the experiment and analysis showed that the modular power conditioning cards can be maintained within their desired maximum operating temperature range of 40 to 45 °C through thermal conduction to a cold plate when operating with their estimated maximum heat output of 16 W per card.

Colozza, Anthony J.↗

Improved control system power unit for large parachutes

Improved control system power unit drives the control surfaces of very large controllable parachutes. The design features subassemblies for determining control surface position and cable loading, and protection of the load sensor against the possibility of damage during manipulation.

Chandler, J. A.↗

Cost study of solar cell space power systems

Historical costs for solar cell space power systems were evaluated. The study covered thirteen missions that represented a broad cross section of flight projects over the past decade. Fully burdened costs in terms of 1971 dollars are presented for the system and the solar array. The costs correlate reasonably well with array area and do not increase in proportion to array area. The trends for array costs support the contention that solar cell and module standardization reduce costs.

Bernatowicz, D. T.↗

New options for satellite power systems /SPS/

The operation of a satellite power system (SPS) involves the conversion of solar energy into electrical energy with the aid of facilities carried by a geosynchronous satellite, the transmission of the obtained energy to earth in the form of microwave radio frequency energy, and the conversion of the energy received on earth into dc current for distribution into the network. Attention is given to questions concerning suitable microwave radiation density, details of space transportation for the construction of the SPS, and suitable approaches for the transformation of the solar energy into electric energy. It appears that a Rankine cycle using cesium as the main working fluid and a steam bottoming cycle might have advantages over a Brayton cycle concept considered earlier. In the area of solar photovoltaic concepts GaAlAs cells have advantages over silicon cells related to lighter weight, efficiency, and resistance to space radiation. The required amount of gallium seems to become available.

Hanley, G. M.↗

Control algorithms and computer simulation of a stand-alone photovoltaic village power system

At Stand-Alone Photovoltaic (SAPV) power systems increase in size and load diversity, the design and simulation of control subsystems takes on added importance. These SAPV systems represent 'mini utilities' with commensurate controls requirements, albeit with the added complexity of the energy source (sunlight received) being an uncontrollable variable. This paper briefly describes a stand-alone photovoltaic power/load system computerized simulation model. The model was tested against operational data from the Schuchuli stand-alone village photovoltaic system and has achieved acceptable levels of simulation accuracy. The model can be used to simulate system designs although with probable battery modification.

Groumpos, P. P.↗

Space station common module power system network topology and hardware development

Candidate power system newtork topologies for the space station common module are defined and developed and the necessary hardware for test and evaluation is provided. Martin Marietta's approach to performing the proposed program is presented. Performance of the tasks described will assure systematic development and evaluation of program results, and will provide the necessary management tools, visibility, and control techniques for performance assessment. The plan is submitted in accordance with the data requirements given and includes a comprehensive task logic flow diagram, time phased manpower requirements, a program milestone schedule, and detailed descriptions of each program task.

Landis, D. M.↗

International Space Power System Interoperability Standards (ISPSIS)

This International Space Power System Interoperability Standards(ISPSIS) is the result of collaborations within the International Space Station (ISS) and Gateway memberships to establish interoperable interfaces, terminology, and techniques, to facilitate collaborative endeavors of space exploration in cislunar and deep space environments. These standards are available for international and commercial partnerships. Standards that are established and internationally recognized have been selected where possible to enable a variety of providers. Increasing hardware commonality among providers while decreasing unique configurations has the potential to reduce the traditional barriers in space exploration: overall mass and volume required to execute a mission. Standardizing interfaces reduces the scope of the development effort. The information within this document represents a set of parameters, which if accommodated in the system architecture support greater efficiencies, promote cost savings, and increase the probability of mission success. These standards are not intended to specify system details needed for implementation nor do they dictate design features behind the interface; specific requirements will be defined in unique documents.

David James Sadey↗