Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Parameter Identifiability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Experimental investigation of hypersonic buzz on a high cross-range shuttle configuration.

An experimental study confirming the existence of hypersonic buzz in the separated region of a space shuttle's downward deflected control surface is described. Wind tunnel tests in helium on a 1:100 scale model of a shuttle type configuration at M = 17.5 clearly demonstrated the occurrence of large scale pressure oscillations throughout a substantial range of angles of attack and control surface deflections. Measurements of surface pressure fluctuations along with high speed schlieren photography served to delineate the boundaries of the phenomenon and to identify the physical parameters necessary for the onset of a buzz condition. Prominent spectral energy peaks were also observed in the surface pressures that could be directly correlated with the instability. These conditions were found to be strongly dependent on the presence of multiple shock interactions and the position of these interactions relative to the location of a reattaching shear layer.

Goldman, R. L.↗

Wind tunnel investigation of helicopter rotor wake effects on three helicopter fuselage models

The effects of rotor downwash on helicopter fuselage aerodynamic characteristics were investigated. A rotor model for generating the downwash was mounted close to each of three fuselage models. The main report presents the force and moment data in both graphical and tabular form and the pressure data in graphical form. This supplement presents the pressure data in tabular form. Each run or parameter sweep is identified by a unique run number. The data points in each run are identified by a point number. The pressure data can be matched to the force data by matching the run and point number.

Wilson, J. C.↗

Real time telemetry and data compression

The generation of telemetry and data compression by the flight program was verified. The adequacy of flight program telemetry control and timing is proven by the analysis of simulation laboratory runs of past programs through the use of telemetry. The telemetry data are correctly issued using specific tags called process input/output (P10) tags. Verification is accomplished by ensuring that a specific P10 tag and mode register setting identifies the correct parameter and that the data are properly scaled for subsequent ground station reduction. It was checked that the LVDC telemetry correctly adheres to the general requirements specified by the EDD. Data compression specifications are verified using compressed data from nominal flight simulations and from a series of perturbations designed to test data table overflows, data dump rates, and compression of data for occurrence events.

Source record↗

Extracting scene feature vectors through modeling, volume 3

The remote estimation of the leaf area index of winter wheat at Finney County, Kansas was studied. The procedure developed consists of three activities: (1) field measurements; (2) model simulations; and (3) response classifications. The first activity is designed to identify model input parameters and develop a model evaluation data set. A stochastic plant canopy reflectance model is employed to simulate reflectance in the LANDSAT bands as a function of leaf area index for two phenological stages. An atmospheric model is used to translate these surface reflectances into simulated satellite radiance. A divergence classifier determines the relative similarity between model derived spectral responses and those of areas with unknown leaf area index. The unknown areas are assigned the index associated with the closest model response. This research demonstrated that the SRVC canopy reflectance model is appropriate for wheat scenes and that broad categories of leaf area index can be inferred from the procedure developed.

Berry, J. K.↗

Secondary cosmic-ray electrons and positrons from 1 to 100 GeV in the upper atmosphere and interstellar space, and interpretation of a recent positron flux measurement

Secondary electron and positron fluxes generated in interstellar space and in the atmosphere from the decays of pions and kaons in inelastic nuclear interactions are calculated by Monte Carlo techniques for lepton energies in the range from 1 to 100 GeV and an assumed thickness of 10 g/sq cm or less for the interstellar or atmospheric material. A simple and accurate analytical model which summarizes the Monte Carlo results and identifies the essential parameters involved is developed and used to interpret a previous positron measurement. It is found that the thickness of interstellar and source material is about 4.3 g/sq cm for cosmic-ray positrons with energies exceeding 4 GeV, a result that is difficult to reconcile with recently proposed two-containment-volume propagation models which predict a thickness of 1.8 g/sq cm for the same energies on the basis of the energy dependence of the measured (Li+Be+B)/(C+O) ratio. It is shown that single-containment-volume (galactic) models invoking an energy-dependent leakage lifetime are compatible with the positron data, but lack a mechanism to explain the energy dependence.

Orth, C. D.↗

Rotor Dynamic State and Parameter Identification from Hovering Transients

State and parameter identifications based on a form of the maximum likelihood method are applied to the problem of extracting linear perturbation models, including rotor dynamic inflow effects, from transient blade flapping measurements. The estimation method is first studied in computer simulations and then applied to cyclic pitch stirring transients generated with a four-bladed rotor model operating in hovering trim conditions. The analytical perturbation models extracted from the transient test results are compared with transient and frequency response tests not used in the state and parameter identification. The identified analytical perturbation model is also compared with a simple theory. The method that is applicable both to small scale and full scale dynamic rotor testing is being extended to perturbations from forward flight trim conditions.

Hohenemser, K. H.↗

F-8C adaptive flight control laws

Three candidate digital adaptive control laws were designed for NASA's F-8C digital flyby wire aircraft. Each design used the same control laws but adjusted the gains with a different adaptative algorithm. The three adaptive concepts were: high-gain limit cycle, Liapunov-stable model tracking, and maximum likelihood estimation. Sensors were restricted to conventional inertial instruments (rate gyros and accelerometers) without use of air-data measurements. Performance, growth potential, and computer requirements were used as criteria for selecting the most promising of these candidates for further refinement. The maximum likelihood concept was selected primarily because it offers the greatest potential for identifying several aircraft parameters and hence for improved control performance in future aircraft application. In terms of identification and gain adjustment accuracy, the MLE design is slightly superior to the other two, but this has no significant effects on the control performance achievable with the F-8C aircraft. The maximum likelihood design is recommended for flight test, and several refinements to that design are proposed.

Hartmann, G. L.↗

The application of a time-domain deconvolution technique for identification of experimental acoustic-emission signals

A method is presented for the signature analysis of pulses by reconstructing in the time domain the shape of the pulse prior to its passing through the measurement system. This deconvolution technique is first evaluated using an idealized system and analytical pulse models and is shown to provide improved results. An experimental situation is then treated; system-component models are developed for the digitizer, tape recorder, filter, transducer and mechanical structure. To accommodate both calibration results and manufacturer's data, and to provide stable mathematical models entails considerable effort: some 30 parameters must be identified to model this system - which is still a substantial approximation - albeit of very high order. Experimental pulses generated by a ball drop, spark discharge and a tearing crack are then deconvoluted 'back through' the system as modeled, using this technique. These results are compared and indicate (a) that consistent shapes may be expected from a given type of source and (b) that some sources can be identified with greater clarity using the deconvolution approach.

Houghton, J. R.↗

Identification of a STOL propulsion plant model from flight data

Accurate dynamic models for propulsion system behavior are critical to successful synthesis of STOL autothrottle/autoland control systems. This paper describes the development of a nonlinear dynamic model for the response of a STOL aircraft in the landing/approach configuration. The model is based upon an analysis of the throttle, governor, and turbofan engine components. Model parameters are directly identified from data acquired during a flight of the NASA Augmentor Wing Jet STOL research aircraft. The accuracy of the model and a comparison of results for two engines are described. Various approaches to modeling propulsion system response for complex systems representative of current and near-term aircraft are discussed.

De Hoff, R. L.↗

Prediction of blade-vortex interaction noise from measured blade pressure

The impulsive nature of noise due to the interaction of a rotor blade with a tip vortex is studied. The time signature of this noise is calculated theoretically based on the measured blade surface pressure fluctuation of an operational load survey rotor in slow descending flight and is compared with the simultaneous microphone measurement. Particularly, the physical understanding of the characteristic features of a waveform is extensively studied in order to understand the generating mechanism and to identify the important parameters. The interaction trajectory of a tip vortex on an acoustic planform is shown to be a very important parameter for the impulsive shape of the noise. The unsteady nature of the pressure distribution at the very leading edge is also important to the pulse shape. The theoretical model using noncompact liner acoustics predicts the general shape of interaction impulse pretty well except for peak amplitude which requires more continuous information along the span at the leading edge.

Nakamura, Y.↗

Prediction of blade vortex interaction noise from measured blade pressure

The impulsive nature of noise due to the interaction of a rotor blade with a tip vortex is studied. The time signature of this noise is calculated theoretically based on the measured blade surface pressure fluctuation of an operational load survey rotor in slow descending flight and is compared with the simultaneous microphone measurement. Particularly, the physical understanding of the characteristic features of a waveform is extensively studied in order to understand the generating mechanism and to identify the important parameters. The interaction trajectory of a tip vortex on an acoustic planform is shown to be a very important parameter for the impulsive shape of the noise. The unsteady nature of the pressure distribution at the very leading edge is also important to the pulse shape. The theoretical model using noncompact linear acoustics predicts the general shape of interaction impulse pretty well except for peak amplitude which requires more continuous pressure information along the span at the leading edge.

Nakamura, Y.↗

Modeling degradation and failure of Ni-Cr-Al overlay coatings

Degradation of a Ni-16Cr-25Al-0.06Zr overlay coating on a Ni-22Cr substrate was examined after oxidation accompanied by thermal cycling. Concentration/distance profiles were measured in the coating and substrate after various one-hour cycles at 1150 C. A numerical model was developed to simulate coating degradation by simultaneous oxidation and coating/substrate interdiffusion. The validity of the model was confirmed by comparison of predicted and measured concentration/distance profiles. The ability of the model to identify critical system parameters was demonstrated for the case of the initial Al and Cr content of the coating and substrate.

Nesbitt, J. A.↗

Multibeam antenna for 30/20 GHz advanced communications satellite using offset shaped, dual reflector surfaces

Progress in the Antenna Technology Study being performed by NASA to characterize an antenna system with a scaning beam with a half-power beam diameter of around 0.3 deg and a minimum width over which the sidelobes stay below the -30 dB level is reported. Continuous U.S. (CONUS) coverage is desired by the satellite antenna system, with 10-20 fixed beams for trunk coverage and a rapidly scanned narrow beam for customer premises. The design specifies 24 beamwidths from east to west and 10 beamwidths from south to north. Reflector parameters have been identified to optimally focus all beams from a planar feed array. An example of coverage expected with the design demonstrates optimized beams for Seattle, Oklahoma City, and Miami, with -3 dB contours in circles 0,25 deg in diameter and a peak directivity of 55 dB. Experimental work was scheduled for 1983.

Smoll, A. E.↗

A Nonlinear Dual-Adaptive Control Strategy for Identification and Control of Flexible Structures

A technique is presented for obtaining a control law to regulate the modal dynamics and identify the modal parameters of a flexible structure. The method is based on using a min-max performance index to derive a control law which may be considered to be a best compromise between optimum one step control and identification inputs. Features of the approach are demonstrated by a computer simulation of the controlled modal response of a flexible beam.

Thau, F. E.↗

Energy Stability of Thermocapillary Convection in Models of the Float Zone Process

The energy-stability of thermocapillary convection in models of the float-zone, crystal-growing process was studied. Stability limits, as functions of pertinent parameters, that will identify conditions which will not allow the existence of an undesirable oscillatory flow instability were determined. Such instabilities may occur in the space processing of semiconductor materials. The determination of the stability limits will involve two sets of numerical computations: (1) solution of the nonlinear governing equations together with the appropriate boundary conditions to determine the basic state (in general, velocity, pressure and temperature fields and the displacement of free surfaces and interfaces); and (2) solution of a nonlinear Euler-Lagrange systems for the energy-stability limit. Both computations, while difficult, should be within the scope of available computer capability and available concepts in numerical analysis. Finite-element methods are attractive candidates for the numerical work.

Neitzel, G. P.↗

Modeling degradation and failure of Ni-Cr-Al overlay coatings

Degradation of a Ni-16Cr-25Al-0.06Zr overlay coating on a Ni-22Cr substrate was examined after oxidation accompanied by thermal cycling. Concentration/distance profiles were measured in the coating and substrate after various one-hour cycles at 1150 C. A numerical model was developed to simulate coating degradation by simultaneous oxidation and coating/substrate interdiffusion. The validity of the model was confirmed by comparison of predicted and measured concentration/distance profiles. The ability of the model to identify critical system parameters was demonstrated for the case of initial Al and Cr content of the coating and substrate.

Nesbitt, J. A.↗

Regional-scale estimates of surface moisture availability and thermal inertia using remote thermal measurements

A review is presented of numerical models which were developed to interpret thermal IR data and to identify the governing parameters and surface energy fluxes recorded in the images. Analytic, predictive, diagnostic and empirical models are described. The limitations of each type of modeling approach are explored in terms of the error sources and inherent constraints due to theoretical or measurement limitations. Sample results of regional-scale soil moisture or evaporation patterns derived from the Heat Capacity Mapping Mission and GOES satellite data through application of the predictive model devised by Carlson (1981) are discussed. The analysis indicates that pattern recognition will probably be highest when data are collected over flat, arid, sparsely vegetated terrain. The soil moisture data then obtained may be accurate to within 10-20 percent.

Carlson, T. N.↗

Factors influencing elastic stresses in double cantilever beam specimens

An elastic stress analysis was conducted for a double cantilever beam (DCB) specimen using finite-element methods. The purpose of this study was to identify the important parameters that influence stresses ahead of the delamination front. The study focused on an aluminum DCB specimen, typical of adhesively-bonded joints, and on a graphite/epoxy specimen representing a cocured composite. Opening mode sigma sub y stresses ahead of the crack tip were calculated and compared with those for a monolithic reference specimen. Beyond the singularity-dominated region very near the crack tip, the sigma sub y distribution was elevated compared to the monolithic case. Both the adhesive thickness and the adherend transverse (thickness-direction) stiffness were found to influence the elevation of sigma sub y. In contrast, adherend thickness and longitudinal stiffness has very little effect on this stress distribution. Estimates for adhesive yielding beyond the aluminum DCB crack tip showed that both the area and height of the plastic zone increased to a peak value for increasing adhesive thicknesses. Results from this study would provide insight for comparing data from different DCB specimens and for designing new DCB specimens.

Crews, J. H., Jr.↗