Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Effect of preparation procedure and nanostructuring on the thermoelectric properties of the lead telluride-based material system AgPb{sub m}BiTe{sub 2+m} (BLST-m)

We report on the preparation and thermoelectric properties of the quaternary system AgPb{sub m}BiTe{sub 2+m} (Bismuth-Lead-Silver-Tellurium, BLST-m) that were nanostructured by mechanical alloying. Nanopowders of various compositions were compacted by three different methods: cold pressing/annealing, hot pressing, and short term sintering. The products are compared with respect to microstructure and sample density. The thermoelectric properties were measured: thermal conductivity in the temperature range from 300 K to 800 K and electrical conductivity and Seebeck coefficient between 100 K and 800 K. The compacting method and the composition had a substantial impact on carrier concentration and mobility as well as on the thermoelectric parameters. Room temperature Hall measurements yielded carrier concentrations in the order of 10{sup 19 }cm{sup −3}, slightly increasing with increasing content of the additive silver bismuth telluride to the lead telluride base. ZT values close to the ones of bulk samples were achieved. X-ray diffraction and transmission electron microscopy (TEM) showed macroscopically homogeneous distributions of the constituting elements inside the nanopowders ensembles, indicating a solid solution. However, high resolution transmission electron microscopy (HRTEM) revealed disorder on the nanoscale inside individual nanopowders grains.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Milestone Report - M3FT-15OR03120215 - Recommend HIP Conditions for AgZ

The purpose of this study was to continue research to determine if HIPing could directly convert I-Ag 0 Z into a suitable waste form. Fiscal year (FY) 2015 work completed studies of Phase IIA, IIB, and IIC samples. Product consistency testing (PCT) of Phase IIA samples resulted in iodine release below detection limit for six of twelve samples. This is promising and indicates that a durable waste form may be produced through HIPing even if transformation of the zeolite to a distinct mineral phase does not occur. From PCT results of Phase IIA samples, it was determined that future pressing should be conducted at a temperature of 900°C. Phase IIC testing continued production of samples to examine the effects of multiple source materials, compositional variations, and an expanded temperature range. The density of each sample was determined and x-ray diffraction (XRD) patterns were obtained. In all cases, there was nothing in the XRD analyses to indicate the creation of any AgI-containing silicon phase; the samples were found to be largely amorphous.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

INL HIP Plate Fabrication

This document outlines the process used to bond monolithic fuel plates by Hot Isostatic Pressing (HIP). This method was developed at Idaho National Laboratory (INL) for the Reduced Enrichment for Research and Test Reactors (RERTR) program. These foils have been used in a number of irradiation experiments in support of the United States Global Threat Reduction Initiative (GTRI) program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Enabling High-Performance NASICON-Based Solid-State Lithium Metal Batteries Towards Practical Conditions

Solid-state lithium metal batteries (SSLMBs) are promising next-generation high-energy rechargeable batteries. However, the practical energy densities of the reported SSLMBs have been significantly overstated due to the use of thick solid-state electrolytes, thick lithium (Li) anodes, and thin cathodes. Here, a high-performance NASICON-based SSLMB using a thin (60 µm) Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolyte, ultrathin (36 µm) Li metal, and high-loading (8 mg cm -2 ) LiFePO 4 (LFP) cathode is reported. The thin and dense LAGP electrolyte prepared by hot-pressing exhibits a high Li ionic conductivity of 1 × 10 -3 S cm -1 at 80 °C. The assembled SSLMB can thus deliver an increased areal capacity of ≈1 mAh cm -2 at C/5 with a high capacity retention of ≈96% after 50 cycles under 80 °C. Furthermore, it is revealed by synchrotron X-ray absorption spectroscopy and in situ high-energy X-ray diffraction that the side reactions between LAGP electrolyte and LFP cathode are significantly suppressed, while rational surface protection is required for Ni-rich layered cathodes. This study provides valuable insights and guidelines for the development of high-energy SSLMBs towards practical conditions.

25 ENERGY STORAGE↗

Investigation of thermal damage in explosive bridgewire detonators via discrete element method simulations

Exploding bridgewire (EBW) detonators are used to rapidly and reliably initiate energetic reactions by exploding a bridgewire via Joule heating. While the mechanisms of EBW detonators have been studied extensively in nominal conditions, comparatively few studies have addressed thermally damaged detonator operability. We present a mesoscale simulation study of thermal damage in a representative EBW detonator, using discrete element method (DEM) simulations that explicitly account for individual particles in the pressed explosive powder. We use a simplified model of melting, where solid spherical particles undergo uniform shrinking, and fluid dynamics are ignored. The subsequent settling of particles results in the formation of a gap between the solid powder and the bridgewire, which we study under different conditions. In particular, particle cohesion has a significant effect on gap formation and settling behavior, where sufficiently high cohesion leads to coalescence of particles into a free-standing pellet. This behavior is qualitatively compared to experimental visualization data, and simulations are shown to capture several key changes in pellet shape. We derive a minimum and maximum limit on gap formation during melting using simple geometric arguments. In the absence of cohesion, results agree with the maximum gap size. With increasing cohesion, the gap size decreases, eventually saturating at the minimum limit. In conclusion, we present results for different combinations of interparticle cohesion and detonator orientations with respect to gravity, demonstrating the complex behavior of these systems and the potential for DEM simulations to capture a range of scenarios.

cohesive powders↗

Strength and fatigue properties enhancement in ultrafine-grained Ti produced by severe plastic deformation

Severe plastic deformation (SPD) of titanium creates an ultrafine-grained (UFG) microstructure which results in significantly enhanced mechanical properties, including increasing the high cycle fatigue strength. This work addresses the challenge of maintaining the high level of properties as SPD processing techniques are evolved from methods suitable for producing laboratory scale samples to methods suitable for commercial scale production of titanium semi-products. Various ways to optimize the strength and fatigue endurance limit in long-length Grade 4 titanium rod processed by equal channel angular pressing (ECAP) with subsequent thermal mechanical treatments are considered in this paper. Low-temperature annealing of rods is found to increase the fatigue limit, simultaneously enhancing UFG titanium strength and ductility. The UFG structure in titanium provides an optimum combination of properties when its microstructure includes mostly equiaxed grains with high-angle boundaries, the volume fraction of which is no less than 50%.

36 MATERIALS SCIENCE↗

Effects of Thermo-Mechanical Processes in the 110 K Phase of Bi{sub 2−x}Pb{sub x}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub y} (x = 0.3–0.6) Superconductors

In this study, the effects of thermo-mechanical processes on the 110 K phase of Bi{sub 2−x}Pb{sub x}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub y} (x = 0.3–0.6) superconductors have been studied. In order to investigate the effects of thermo-mechanical processes, the samples were prepared in three groups with different sintering temperatures having intermediate grindings and pressings. The superconducting and structural properties of BPSCCO system were characterized by R(T), χ(T), and J{sub c} measurements; XRD; and SEM analysis. The thermo-mechanical processes were investigated to explain how they affect T{sub c} and metallic properties of the samples. According to the analysis, we obtained that the 110 K phase of BPSCCO samples was significantly affected by these thermal and mechanical processes. The preparation conditions were optimized in order to obtain a BPSCCO system having dominant phase of 110 K with the superior superconducting properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ex Situ Spark Plasma Sintering of Short Powder-in-Tube MgB{sub 2} Tapes with Open and Closed Ends

Short powder-in-tube tapes of MgB{sub 2} in the Fe sheath were fabricated by ex situ route from a commercial powder containing some free Mg and MgO impurity phases. The final heat treatment was performed by spark plasma sintering (SPS). Tapes were with open (OT) or closed (CT) endings. Closed endings were made by folding and pressing. The MgB{sub 2} core of the OT sample has shown a higher low-field critical current density, a higher maximum pinning force, a slightly higher disorder, smaller average MgB{sub 2} crystallite size, a weak contact between Fe and MgB{sub 2} core, and more macro-flux jumps. The upper and irreversibility fields were similar for OT and CT samples. In the center of the MgB{sub 2} cores, the detected impurity phase is MgO, while at the interface with Fe, MgB{sub 4} also occurs. Impurity phases found at interface, MgO and MgB{sub 4}, are present in the center of the bulk SPSed samples. Reactions and pinning-force-related parameters are discussed with respect to Mg behavior influenced by condition of endings. It is inferred that the presence of free Mg in the raw MgB{sub 2} powder has an important contribution to observed differences, and its removal or control is recommended.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Potential method for measurement of CO2 leakage from underground sequestration fields using radioactive tracers

Reduction of anthropogenic carbon dioxide (CO2) release to the environment is a pressing challenge that should be addressed to avert the potential devastating effects of global warming. Within the United States, the most abundant sources of CO2 emissions are those generate from coal- or gas-fired power plants; one method to control CO2 emissions is to sequester it in deep underground geological formations. From integrated assessment models the overall leakage rates from these storage locations must be less than 0.1% of stored volume per year for long-term control. The ability to detect and characterize nascent leaks, in conjunction with subsequent remediation efforts, will significantly decrease the amount of CO2 released back into the environment. Because potential leakage pathways are not necessarily known a priori, onsite monitoring must be performed; the monitoring region in the vicinity of a CO2 injection well may be as large as 100 km2, which represents the estimated size of a supercritical CO2 bubble that would form under typical injection scenarios. By spiking the injected CO2 with a radiological or stable isotope tracer, it will be possible to detect ground leaks from the sequestered CO2 using fewer sampling stations, with greater accuracy than would be possible using simple CO2 sensors. The relative merits of various sorbent materials, radiological and stable isotope tracers, detection methods and potential interferences will be discussed.

01 COAL, LIGNITE, AND PEAT↗

Dielectric and piezoelectric properties of 0.970(0.95(K{sub 0.485}Na{sub 0.515})NbO{sub 3}–0.05LiSbO{sub 3})–0.015CuO–0.015Al{sub 2}O{sub 3}/PVDF 0–3 composite reinforced with two kinds of ZnO powder

0.970(0.95(K{sub 0.485}Na{sub 0.515})NbO{sub 3}–0.05LiSbO{sub 3})–0.015CuO–0.015Al{sub 2}O{sub 3} (KNNLS–CA) ceramic powder obtained through the conventional solid state reaction. The ZnO nanoparticles (denoted as ZnO1) and poly (vinylidene fluoride) (PVDF) were supplied from commercial companies. The self-synthesized ZnO powder (denoted as ZnO2) were prepared by hydrothermal method using Zn (CH{sub 3}COO){sub 2}·2H{sub 2}O and NaOH. Subsequently, the two kinds of composites were fabricated by hot-pressing process using KNNLS–CA ceramic powder, two kinds of ZnO powder and PVDF polymer. The effects of the ZnO on the crystalline structures, morphology, thermal stability, densities and electric properties of composites were studied systemically. The KNNLS–CA ceramic possesses a perovskite phase with orthorhombic symmetry and peaks from the second phase of K{sub 3}Li{sub 2}Nb{sub 5}O{sub 15} (PDF#52-0157) are detected by X-ray diffraction. PVDF polymer mainly possesses α, β and γ phases. Two kinds of ZnO all possess hexagonal wurtzite structures without any impurity phase. It is worth noting that the ZnO particles have great impacts on lattice constants, strain and crystallinity. In addition, the ZnO particles can enhance the relative fraction of β phase in PVDF and improve the thermal stability of the composite. Interestingly, the dielectric and piezoelectric properties are also found to be improved with the increase of ZnO content. Especially, when 10 wt.% ZnO2 is doped, the dielectric permittivity reaches the value of 586.4 (100 Hz) at room temperature and the piezoelectric constant is 64 pC/N. After 30 days of aging test, it is obvious that all the composites present a good stability of piezoelectric property.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Evaluating the SWAT Model for Hydrological Modeling in the Xixian Watershed and A Comparison with the XAJ Model

Already declining water availability in Huaihe River, the 6th largest river in China, is further stressed by climate change and intense human activities. There is a pressing need for a watershed model to better understand the interaction between land use activities and hydrologic processes and to support sustainable water use planning. In this study, we evaluated the performance of SWAT for hydrologic modeling in the Xixian River Basin, located at the headwaters of the Huaihe River, and compared its performance with the Xinanjiang (XAJ) model that has been widely used in China

54 ENVIRONMENTAL SCIENCES↗

Investigation of the Effect of Foaming Agent on the Fabrication of NiTi Foams Using the Self-Propagating, High-Temperature Synthesis Process

Fabrication of NiTi intermetallic foams using the self-propagating, high-temperature synthesis (SHS) process was investigated. Weighed amounts of powders taken from an equimolar mixture of Ni and Ti powders along with 0.5, 1, and 1.5 wt pct of different foaming agents were cold pressed to form cylindrical compacts 10 mm in diameter, 20 mm in height, and 7 to 8 g in weight. A novel, induction-assisted ignition method was used for indirect heating and igniting the compressed mixtures at one end. As a result of intensive exothermic reaction between Ni and Ti and decomposition of foaming agents and liberation of gases, highly porous products were obtained. Characterization of the products was carried out using X-ray diffraction (XRD) and a scanning electron microscope equipped with an energy-dispersive spectroscope (SEM-EDS). The main phase in the products was detected to be B2(NiTi) with minor amounts of NiTi{sub 2} as the secondary phase. Other undesirable phases, such as Ni{sub 4}Ti{sub 3} and Ni{sub 3}Ti, were not detected. The effect of type and percentage of foaming agent on the formation and distribution of pores within the products was studied. Final products with porosities up to ~ 80 vol pct were obtained by adding foaming agent. Under the conditions of this study, CaH{sub 2} proved to be the most effective foaming agent considering its ability to generate a uniform distribution of pores, while TiH{sub 2} was not considered favorable due to its decomposition at relatively low temperatures. In general, the addition of foaming agents in amounts higher than 1wt pct is not recommended; due to the endothermic nature of thermal decomposition reactions of foaming agents, excessive use of these agents can result in suppression of the exothermic reaction.

36 MATERIALS SCIENCE↗

Additive Manufacturing of PLA and CF/PLA Binding Layer Specimens via Fused Deposition Modeling

As one of the most popular additive manufacturing techniques, fused deposition modeling (FDM) is successfully applied in aerospace, automotive, architecture, and other fields to fabricate thermoplastic parts. Unfortunately, as a result of the limited nature of the mechanical properties and mass in raw materials, there is a pressing need to improve mechanical properties and reduce weight for FDM parts. Therefore, this paper presents an experiment of a special polylactic acid (PLA) and carbon fiber (CF)/PLA-laminated experimental specimen fabricated using the FDM process. The mechanical properties and mass analysis of the new composites for the PLA and CF/PLA binding layer specimen are investigated experimentally. Through the experimental analysis, one can conclude that the mass of laminated specimen is lighter than the CF/PLA specimen, and the tensile and flexural mechanical properties are higher than the pure PLA specimen.

36 MATERIALS SCIENCE↗

Preparation and Dynamic Mechanical Properties at Elevated Temperatures of a Tungsten/Glass Composite

Experiments were conducted to prepare a borosilicate glass matrix composite containing 50 vol.% tungsten and examine its dynamic compressive behavior at elevated temperatures in the range of 450-775 °C. The results show that the homogenous microstructure of the tungsten/glass composite with relative density of ~ 97% can be obtained by hot-pressing sintering at 800 °C for 1 h under pressure of 30 MPa. Dynamic compressive testing was carried out by a separate Hopkinson pressure bar system with a synchronous device. The results show that the peak stress decreases and the composite transforms from brittle to ductile in nature with testing temperature increasing from 450 to 750 °C. The brittle–ductile transition temperature is about 500 °C. Over 775 °C, the composite loses load-bearing capacity totally because of the excessive softening of the glass phase. In addition, the deformation and failure mechanism were analyzed.

36 MATERIALS SCIENCE↗

The Prediction of Microstructure Evolution of 6005A Aluminum Alloy in a P-ECAP Extrusion Study

Finite element modeling (FEM) was applied for predicting the recrystallized structure in extruded 6005 aluminum alloy, and simulated results were experimentally validated. First, microstructure evolution of 6005 aluminum alloy during deformation was studied by means of isothermal compression test, where the processing parameters were chosen to reproduce the typical industrial conditions. Second, microstructure evolution was analyzed, and the obtained information was used to fit a dynamic recrystallization model implementing inside the DEFORM-3D FEM code environment. FEM of deformation of 6005 aluminum has been established and validated by microstructure comparison. Finally, the obtained dynamic recrystallization model was applied to tube extrusion by using a portholes-equal channel angular pressing die. The finite element analysis results showed that coarse DRX grains occur in the extruded tube at higher temperature and in the extruded tube at the faster speed of the stem. The test results showed material from the front end of the extruded tube has coarse grains (60 μm) and other extruded tube has finer grains (20 μm).

36 MATERIALS SCIENCE↗

Densification, Microstructural Evolution, Mechanical Properties and Oxidation Study of CrB{sub 2} + EuB{sub 6} Composite

This paper reports the results of investigation on densification, microstructural evolution, mechanical properties and oxidation study of CrB{sub 2} + EuB{sub 6} composite. CrB{sub 2} + EuB{sub 6} (10 and 20 wt.%) composites have been fabricated by hot pressing at a temperature of 1700 °C and 35 MPa pressure. The hardness and flexural strength were measured in the range of 21.25-24.48 GPa and 171-199 MPa, respectively. The fracture toughness increased from 3.3 to 4.01 MPa m{sup 1/2} by the addition of 20% EuB{sub 6}. Microstructural evolution revealed the uniform distribution of EuB{sub 6} and absence of any reaction product. Fracture surface analysis confirmed the presence of transgranular mode of fracture. Oxidation study at 1200 °C revealed that the developed composites have good oxidation resistance and followed the parabolic rate of oxidation.

36 MATERIALS SCIENCE↗

Control of Carbon Content in Ultrafine Cemented Carbide by Heat Treatment in Reducing Atmospheres Containing Carbon Oxides

In this work, the method of control of carbon content in the ultrafine-grained cemented carbide alloy was proposed. The treating of the WC-8Co-0.4VC-0.4Cr{sub 3}C{sub 2} compacts was made in a CO + CO{sub 2} gas mixture at CO concentrations from 0 to 80 vol.% during 50 min at the initial stage of the conventional sintering at a temperature of 700 °C. Conditions for increasing and decreasing the carbon content are CO concentrations of CO in gas mix more than 65 vol.% and less than 35 vol.%, respectively. It is shown that even a small deviation from the stoichiometric carbon content (0.3 wt.%) leads to an increase in porosity and a multiple decrease in the strength of the ultrafine-grained cemented carbide. A comparative analysis with literature data showed that the obtained ultrafine-grained solid alloy WC-8Co-0.4VC-0.4Cr{sub 3}C{sub 2} with stoichiometric composition is not inferior in hardness and toughness to the analogs obtained by hot pressing and electrospark sintering.

36 MATERIALS SCIENCE↗

Effect of Different Post-treatments on the Microstructure of EBM-Built Alloy 718

Electron beam melting (EBM) of Alloy 718 is of rapidly growing interest as it allows cost-effective production of complex components. However, the inherent flaws in the component in as-built state are of concern in view of the severe working conditions in which Alloy 718 components typically operate. The present work entails an investigation of changes in microstructure that accompany some post-treatments that are being widely considered to address defects in EBM processed Alloy 718. The effect of two different post-treatments, namely hot isostatic pressing (HIP) and a combined HIP + heat treatment (HT) carried out inside the HIP vessel, have been studied and results from as-built and post-treated specimens were compared in terms of porosity/lack-of-fusion, microstructure, phase constitution (NbC content, δ-phase) and micro-hardness. Post-treatment resulted in reduction in defect content by more than an order of magnitude. HIPing led to complete dissolution of δ phase. In comparison to as-built material, HIPed specimens exhibited significant drop in hardness. However, a sharp ‘recovery’ of hardness to yield values higher than in as-built condition was observed after HIP + HT and can be attributed to precipitation of γ′′ phase.

36 MATERIALS SCIENCE↗