Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Jet Surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Application of Sweeping Jet Actuators on the NASA Hump Model and Comparison with CFDVAL2004 Experiments

Flow separation control over a wall-mounted hump model was studied experimentally to assess the performance of sweeping jet actuators. Results were compared to that of the 2004 CFD validation experiment (CFDVAL2004), which examined flow separation control with steady suction and unsteady zero-net-mass-flow actuators. Comparisons were carried out at low and high amplitude excitations. In addition to the active flow control methods, a passive flow control method (i.e., vortex generator) was used to complement the dataset. Steady/unsteady surface pressure measurements and surface oilflow visualization were used in the performance assessment of the actuators. The results indicated that the sweeping jet actuators are more effective than the steady suction and unsteady zero-net-mass-flow actuators. For the same momentum coefficient, the sweeping jet actuators produced more flow acceleration upstream of separation, more pressure recovery downstream, and consistently a smaller separation bubble.

Koklu, Mehti↗
NASA NTRS2019

FUN3D and USM3D Analysis of the 4th AIAA Propulsion Aerodynamics Workshop Nozzle Test Case

This work presents the results of FUN3D and USM3D analyses that were performed for the 4th AIAA Propulsion Aerodynamics Workshop. The workshop was separated into three sections that focus on internal duct flows, nozzle flows, and a special topic of interest. This paper focuses on the nozzle section while an accompanying paper discusses the analyses performed for the internal duct flow section. For the nozzle flow section, the participants were provided with two configurations consisting of a rectangular convergent nozzle with and without an aft-deck. User-generated grids were developed under the guidelines of the workshop for the present analyses. The results show that both solvers compare favorably to the experimental results for the baseline nozzle with the largest differences observed at the lower NPR values. Additionally, both solvers showed favorable agreement with the experimental data for the pressures on the surface of the aft-deck. However, neither solver was able to match the jet flow further downstream for the nozzle with aft-deck configuration. A turbulence model study was conducted to compare the two-equation SST model, SA-QCR model, and two-equation k-kL model (FUN3D only). The results show that the SA-QCR turbulence model was unable to match the experimental results downstream of the nozzle. The k-kL model was shown to better match the experimental data compared to the SST model for most cases simulated using the FUN3D flow solver. Suggestions for future workshops include gridding guidelines similar ion Workshop series for the grid refinement study and a reduction in scope to allow for more detailed exploration of the individual problems. rticipation by reducing time requirements

Bozeman, Michael D.↗
NASA NTRS2021

Distributed Aperture Radar Tomographic Sensors (darts) to Map Surface Topography and Vegetation Structure

Distributed Aperture Radar Tomographic Sensors (DARTS)is a mission concept being studied at the NASA Jet PropulsionLaboratory in collaboration with the California Institute ofTechnology to enable global and repeated imaging of surfacetopography and three-dimensional vegetation structure usingsingle-pass tomographic SAR technique. The observing systemconsists of a distributed formation of multiple small syntheticaperture radar platforms deployed in space with variabledistances to achieve look angle diversity and sensitivityto the vertical distribution of vegetation components. Ourgoal is to identify the optimal system configuration startingfrom documented community needs and mature the criticaltechnologies that lead to a viable implementation of DARTS.Here, we provide an overview of DARTS and describe ourapproach for designing and demonstrating single-pass SARtomographic systems as part of an on-going funded NASA Instrument Incubator Program effort.

Chung, Soon-Jo↗
NASA NTRS1996

Spray Combustion Modeling with VOF and Finite-Rate Chemistry

A spray atomization and combustion model is developed based on the volume-of-fluid (VOF) transport equation with finite-rate chemistry model. The gas-liquid interface mass, momentum and energy conservation laws are modeled by continuum surface force mechanisms. A new solution method is developed such that the present VOF model can be applied for all-speed range flows. The objectives of the present study are: (1) to develop and verify the fractional volume-of-fluid (VOF) cell partitioning approach into a predictor-corrector algorithm to deal with multiphase (gas-liquid) free surface flow problems; (2) to implement the developed unified algorithm in a general purpose computational fluid dynamics (CFD) code, Finite Difference Navier-Stokes (FDNS), with droplet dynamics and finite-rate chemistry models; and (3) to demonstrate the effectiveness of the present approach by simulating benchmark problems of jet breakup/spray atomization and combustion. Modeling multiphase fluid flows poses a significant challenge because a required boundary must be applied to a transient, irregular surface that is discontinuous, and the flow regimes considered can range from incompressible to highspeed compressible flows. The flow-process modeling is further complicated by surface tension, interfacial heat and mass transfer, spray formation and turbulence, and their interactions. The major contribution of the present method is to combine the novel feature of the Volume of Fluid (VOF) method and the Eulerian/Lagrangian method into a unified algorithm for efficient noniterative, time-accurate calculations of multiphase free surface flows valid at all speeds. The proposed method reformulated the VOF equation to strongly couple two distinct phases (liquid and gas), and tracks droplets on a Lagrangian frame when spray model is required, using a unified predictor-corrector technique to account for the non-linear linkages through the convective contributions of VOF. The discontinuities within the sharp interface will be modeled as a volume force to avoid stiffness. Formations of droplets, tracking of droplet dynamics and modeling of the droplet breakup/evaporation, are handled through the same unified predictor-corrector procedure. Thus the new algorithm is non-iterative and is flexible for general geometries with arbitrarily complex topology in free surfaces. The FDNS finite-difference Navier-Stokes code is employed as the baseline of the current development. Benchmark test cases of shear coaxial LOX/H2 liquid jet with atomization/combustion and impinging jet test cases are investigated in the present work. Preliminary data comparisons show good qualitative agreement between data and the present analysis. It is indicative from these results that the present method has great potential to become a general engineering design analysis and diagnostics tool for problems involving spray combustion.

Chen, Yen-Sen↗
NASA NTRS1991

Breakup of a liquid jet in supersonic crossflow

A theoretical study of the breakup of a circular liquid jet injected transversely into a supersonic air stream is conducted. Two different criteria for breakup are explored in the context of a previously developed model for the behavior of liquid jets in compressible crossflow (Heister et al., 1989). The local sonic point criterion first proposed by Schetz, et al. (1980) is explored, in addition to an auxiliary criterion put forth by Clark (1964) based on surface-tension stability. It is found that the local sonic point appears to provide a more reasonable approximation to the actual location of jet breakup, based on comparisons with limited experimental data.

Li, H.-S.↗
NASA NTRS2015

Arc Jet Facility Test Condition Predictions Using the ADSI Code

The Aerothermal Design Space Interpolation (ADSI) tool is used to interpolate databases of previously computed computational fluid dynamic solutions for test articles in a NASA Ames arc jet facility. The arc jet databases are generated using an Navier-Stokes flow solver using previously determined best practices. The arc jet mass flow rates and arc currents used to discretize the database are chosen to span the operating conditions possible in the arc jet, and are based on previous arc jet experimental conditions where possible. The ADSI code is a database interpolation, manipulation, and examination tool that can be used to estimate the stagnation point pressure and heating rate for user-specified values of arc jet mass flow rate and arc current. The interpolation is performed in the other direction (predicting mass flow and current to achieve a desired stagnation point pressure and heating rate). ADSI is also used to generate 2-D response surfaces of stagnation point pressure and heating rate as a function of mass flow rate and arc current (or vice versa). Arc jet test data is used to assess the predictive capability of the ADSI code.

fluid dynamics↗
NASA NTRS1999

High velocity pulsed wire-arc spray

Wire arc spraying using repetitively pulsed, high temperature gas jets, usually referred to as plasma jets, and generated by capillary discharges, substantially increases the velocity of atomized and entrained molten droplets. The quality of coatings produced is improved by increasing the velocity with which coating particles impact the coated surface. The effectiveness of wire-arc spraying is improved by replacing the usual atomizing air stream with a rapidly pulsed high velocity plasma jet. Pulsed power provides higher coating particle velocities leading to improved coatings. 50 micron aluminum droplets with velocities of 1500 m/s are produced. Pulsed plasma jet spraying provides the means to coat the insides of pipes, tubes, and engine block cylinders with very high velocity droplet impact.

Witherspoon, F. Douglas↗
NASA NTRS2001

Response Surface Modeling Using Multivariate Orthogonal Functions

A nonlinear modeling technique was used to characterize response surfaces for non-dimensional longitudinal aerodynamic force and moment coefficients, based on wind tunnel data from a commercial jet transport model. Data were collected using two experimental procedures - one based on modem design of experiments (MDOE), and one using a classical one factor at a time (OFAT) approach. The nonlinear modeling technique used multivariate orthogonal functions generated from the independent variable data as modeling functions in a least squares context to characterize the response surfaces. Model terms were selected automatically using a prediction error metric. Prediction error bounds computed from the modeling data alone were found to be- a good measure of actual prediction error for prediction points within the inference space. Root-mean-square model fit error and prediction error were less than 4 percent of the mean response value in all cases. Efficacy and prediction performance of the response surface models identified from both MDOE and OFAT experiments were investigated.

Morelli, Eugene A.↗
NASA NTRS1982

The Halley dust model

The properties of dust ejecta from Comet Halley are studied on the basis of (a) evidence from the comet's past apparitions and (b) analogy with recent, physically similar comets. Specifically discussed are the light curve and spectrum, discrete phenomena in the head, the physical properties of the nucleus (size, albedo, rotation, surface temperature, and morphology), and an interaction between the nucleus and dust atmosphere. Also reviewed are constraints on the size and mass distributions of dust particles, information on submicron-size and submillimeter-size grains from the comet's dust tail and antitail, and the apparent existence of more than one particle type. Similarities between the jet patterns of Halley and the parent comet of the Perseid meteor stream are depicted, and effects of the surface heterogeneity (discrete active regions) on the dust flow are assessed. Current dust models for Halley are summarized and the existence of short-term variations in the dust content in the comet's atmosphere is suggested.

Sekanina, Z.↗
NASA NTRS1992

The effects of nozzle exit geometry on forebody vortex control using blowing

An experimental study has been undertaken to examine the influence of the blowing jet geometry on the effectiveness of the aft blowing technique for forebody vortex control. The experiments were conducted with a 3.0 tangent caliber ogive model at subsonic, laminar flow conditions. Asymmetric aft blowing was accomplished using both a single nozzle and a double nozzle configuration. Detailed surface pressure measurements on the model were obtained. The experimental results show that the height and the width of the blowing jet are important parameters that determine the effectiveness of aft blowing; a broad, lowly positioned blowing jet is found to be most effective for the forebody vortex control technique using aft blowing.

Gittner, Nathan M.↗
NASA NTRS1994

Orbital velocities induced by surface waves

During the third intensive observational period of the Surface Wave Dynamics Experiment (SWADE), an aircraft-based experiment was conducted on 5 March 1991 by deploying slow-fall airborne expendable current profilers (AXCPs) and airborne expendable bathythermographs (AXBTs) during a scanning radar altimeter (SRA) flight on the NASA NP-3A research aircraft. As the Gulf Stream (GS) moved into the SWADE domain in late February, maximum upper-layer currents of 1.98 m/s were observed in the core of the baroclinic jet where the vertical current shears were O(10(exp -2)/s). The SRA concurrently measured the sea surface topography, which was transformed into two-dimensional directional wave spectra at 5-6-km intervals along the flight tracks. The wave spectra indicated a local wave field with wavelengths of 40-60 m propagating southward between 120 deg and 180 deg, and a northward-moving swell field from 300 deg to 70 deg associated with significant wave heights of 2-4 m. As the AXCP descended through the upper ocean, the profiler sensed orbital velocity amplitudes of 0.2-0.5 m/s due to low-frequency surface waves. These orbital velocities were isolated by fitting the observed current profiles to the three-layer model based on a monochromatic surface wave, including the steady and current shear terms within each layer. The depth-integrated differences between the observed and modeled velocity profiles were typically less than 3 cm/s. For 17 of the 21 AXCP drop sites, the rms orbital velocity amplitudes, estimated by integrating the wave spectra over direction and frequency, were correlated at a level of 0.61 with those derived from the current profiles. The direction of wave propagation inferred from the AXCP-derived orbital velocities was in the same direction observed by the SRA. These mean wave directions were highly correlated (0.87) and differed only by about 5 deg.

Shay, Lynn K.↗
NASA NTRS1986

A diagnostic study of baroclinic disturbances in polar air streams

Quasi-Lagrangian budgets of mass, vorticity and heat are calculated following disturbances that form within polar air streams. Observed cases are extracted from the European Centre for Medium-range Weather Forecasts analyses during the First GARP Global Experiment. Model-generated cases are extracted from the simulations of extratropical cyclogenesis by Sandgathe. These polar lows grow primarily through basic baroclinic instability processes and exhibit many features of larger maritime extratropical cyclones. Polar lows that originate on the poleward (or Cyclonic - Type C) side of the jet and have considerable midtropospheric positive vorticity advection at formation time are contrasted with lows that form on the equatorward (or Anticyclonic - Type A) side of a nearly straight upper-level jet. The midtropospheric positive vorticity advection must be present to enhance the vertical circulation when the large surface fluxes that are associated with strong outbreaks act to damp the thermal wave amplification. Although latent heat release is an important factor in both types, it is an essential energy source for the Type A low developments on the equatorward side. Although the vorticity balance is initially different for the two types of polar lows, the vorticity budgets during later stages are similar. The heat budget and the thickness tendency equation demonstrated that the self-development process that is present in larger maritime cyclones is also important for polar low intensification. The absence of favorable coupling to a jet stream is the missing factor in a model-generated Type A polar low that failed to develop. Consequently, the mid- and upper-tropospheric wind fields determine which polar lows will intensify to significant amplitudes.

Sinclair, Mark R.↗
NASA NTRS2004

Blowing Flap Experiment: PIV Measurements

PIV measurements of the flow in the region of a flap side edge are presented for several flap configurations. The test model is a NACA 63(sub 2)-215 Hicks Mod-B main element airfoil with a half-span Fowler flap. Air is blown from small slots located along the flap side edge on either the top, bottom or side surfaces. The test set up is described and flow measurements for a baseline and three blowing flap configurations are presented. The effects that the flap tip jets have on the structure of the flap side edge flow are discussed for each of the flap configurations tested. The results indicate that blowing air from a slot located along the top surface of the flap greatly weakened the top vortex system and pushed it further off the top surface. Blowing from the bottom flap surface kept the strong side vortex further outboard while blowing from the side surface only strengthened the flap vortex system. It is concluded that blowing from the top or bottom surfaces of the flap may lead to a reduction of flap side edge noise.

Hutcheson, Florence V.↗
NASA NTRS2004

PIV Measurements on a Blowing Flap

PIV measurements of the flow in the region of a flap side edge are presented for several blowing flap configurations. The test model is a NACA 63(sub 2)-215 Hicks Mod-B main-element airfoil with a half-span Fowler flap. Air is blown from small slots located along the flap side edge on either the top, bottom or side surfaces. The test set up is described and flow measurements for a baseline and three blowing flap configurations are presented. The effects that the flap tip jets have on the structure of the flap side edge flow are discussed for each of the flap configurations tested. The results indicate that blowing air from a slot located along the top surface of the flap greatly weakened the top vortex system and pushed it further off the top surface. Blowing from the bottom flap surface kept the strong side vortex further outboard while blowing from the side surface only strengthened the vortex system or accelerated the merging of the side vortex to the flap top surface. It is concluded that blowing from the top or bottom surfaces of the flap may lead to a reduction of flap side edge noise.

Hutcheson, Florence V.↗
NASA NTRSDate not supplied

Variable Mixing Nozzle Design with Slotted Vortex Generators for Jet Noise Reduction

A new variable geometry turbofan nozzle concept is presented with the dual goals of airport noise reduction and high propulsive efficiency at cruise, while employing only a single moving part. The nozzle utilizes a number of curved vanes to function as vortex generators (VGs) during takeoff and initial climb. Streamwise vortices provide an increase in mixing between the jet and external stream, with a resulting decrease in high frequency noise generation and a noise source distribution which is more amenable to airframe-based shielding. Unlike conventional VGs, the vanes are positioned without transverse incidence, and a pressure difference across the surface of each vane is created via an adjacent slot. During high altitude flight, when nozzle efficiency concerns outweigh any preference for jet noise reduction, all slots may be closed through rotation of a slotted ring inside the nozzle. RANS-based numerical analysis is performed to calculate propulsive metrics, determine noise source characteristics and understand various design parameter sensitivities. A new formulation is developed to approximately correct computed noise intensities for any throttle adjustments required to maintain takeoff thrust, and a rough estimate of shielding effectiveness is proposed by means of integration over a spatially distributed noise source. A total of 19 different nozzle geometries are considered in the present study. Results indicate significant noise benefits at takeoff, including a 2 kHz fly-over noise reduction of roughly 2-3 dB, while allowing for less than 15% of the net thrust reduction at supersonic cruise calculated for a fixed-penetration chevron nozzle.

Jet Noise↗
NASA NTRS2015

Lander Technologies

Since 2006 NASA has been formulating robotic missions to the lunar surface through programs and projects like the Robotic Lunar Exploration Program, Lunar Precursor Robotic Program, and International Lunar Network. All of these were led by NASA Marshall Space Flight Center (MSFC). Due to funding shortfalls, the lunar missions associated with these efforts, the designs, were not completed. From 2010 to 2013, the Robotic Lunar Lander Development Activity was funded by the Science Mission Directorate (SMD) to develop technologies that would enable and enhance robotic lunar surface missions at lower costs. In 2013, a requirements-driven, low-cost robotic lunar lander concept was developed for the Resource Prospector Mission. Beginning in 2014, The Advanced Exploration Systems funded the lander team and established the MSFC, Johnson Space Center, Applied Physics Laboratory, and the Jet Propulsion Laboratory team with MSFC leading the project. The lander concept to place a 300-kg rover on the lunar surface has been described in the New Technology Report Case Number MFS-33238-1. A low-cost lander concept for placing a robotic payload on the lunar surface is shown in figures 1 and 2. The NASA lander team has developed several lander concepts using common hardware and software to allow the lander to be configured for a specific mission need. In addition, the team began to transition lander expertise to United States (U.S.) industry to encourage the commercialization of space, specifically the lunar surface. The Lunar Cargo Transportation and Landing by Soft Touchdown (CATALYST) initiative was started and the NASA lander team listed above is partnering with three competitively selected U.S. companies (Astrobotic, Masten Space Systems, and Moon Express) to develop, test, and operate their lunar landers.

Chavers, Greg↗
NASA NTRS1974

Effects of reaction control system jet flow field interactions on the aerodynamic characteristics of a 0.010-scale space shuttle orbiter model in the Langley Research Center 31 inch CFHT (OA85)

An experimental investigation was conducted to obtain detailed effects on supersonic vehicle hypersonic aerodynamic and stability and control characteristics of reaction control system jet flow field interactions with the local vehicle flow field. A 0.010-scale model was used. Six-component force data and wing, elevon, and body flap surface pressure data were obtained through an angle-of-attack range of -10 to +35 degrees with 0 deg angle of sideslip. The test was conducted with yaw, pitch and roll jet simulation at a free-stream Mach number of 10.3 and reaction control system plume simulation of flight dynamic pressures of 5, 10 and 20 PSF.

Daileda, J. J.↗
NASA NTRS1983

Accretion disks, precessing jets and the asymmetric emission lines of QSOs

The broad line profiles of active galaxies are consistent with emission from the surface of an accretion disk ionized by an ultraviolet continuum emitted from a linear or point source of continuum above the disk. If the point source is offset from the axis of the disk, then the line peak is shifted from zero velocity in a way that resembles observed cases. This misalignment could result from the Lense-Thirring precession of a rotating black hole.

Shields, G. A.↗