Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High performance Computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

An Imaging Infrared (IIR) seeker using a microprogrammed processor

A recently developed Imaging Infrared Seeker uses a microprogrammed processor to perform gimbal servo control and system interface while performing the seeker functions of automatic target detection, acquisition, and tracking. The automatic detection mode requires up to 80% of the available capability of a high performance microprogrammed processor. Although system complexity was increased significantly, this approach can be cost effective when the basic computation capacity is already available.

Richmond, K. V.↗
NASA NTRS1985

Automatic Robot Safety Shutdown System

Robot turned off if acceleration exceeds preset value. Signals from accelerometer on robot arm pass through filter and amplifier, eliminating high-frequency noise and hydraulic-pump pulsations. Data digitized and processed in computer. Unit controls other machines that perform repetitive movements, including rotary tables, tracked vehicles, conveyor lines, and elevators.

Lirette, M.↗
NASA NTRS1987

Telemetry handling on the Space Station data management system

This paper examines the impact of telemetry handling on the design of the onboard networks that are part of the Space Station Data Management System (DMS). An architectural approach to satisfying the DMS requirement for support of the high throughput needed for telemetry transport and for servicing distributed computer systems is discussed. Several of the functionality vs. performance tradeoffs that must be made in developing an optimized mechanism for handling telemetry data in the DMS are considered.

Whitelaw, Virginia A.↗
NASA NTRS1990

Advanced modulation technology development for earth station demodulator applications. Coded modulation system development

A jointly optimized coded modulation system is described which was designed, built, and tested by COMSAT Laboratories for NASA LeRC which provides a bandwidth efficiency of 2 bits/s/Hz at an information rate of 160 Mbit/s. A high speed rate 8/9 encoder with a Viterbi decoder and an Octal PSK modem are used to achieve this. The BER performance is approximately 1 dB from the theoretically calculated value for this system at a BER of 5 E-7 under nominal conditions. The system operates in burst mode for downlink applications and tests have demonstrated very little degradation in performance with frequency and level offset. Unique word miss rate measurements were conducted which demonstrate reliable acquisition at low values of Eb/No. Codec self tests have verified the performance of this subsystem in a stand alone mode. The codec is capable of operation at a 200 Mbit/s information rate as demonstrated using a codec test set which introduces noise digitally. The measured performance is within 0.2 dB of the computer simulated predictions. A gate array implementation of the most time critical element of the high speed Viterbi decoder was completed. This gate array add-compare-select chip significantly reduces the power consumption and improves the manufacturability of the decoder. This chip has general application in the implementation of high speed Viterbi decoders.

Miller, Susan P.↗
NASA NTRS1991

Hypersonic Research Vehicle (HRV) real-time flight test support feasibility and requirements study. Part 2: Remote computation support for flight systems functions

The requirements are assessed for the use of remote computation to support HRV flight testing. First, remote computational requirements were developed to support functions that will eventually be performed onboard operational vehicles of this type. These functions which either cannot be performed onboard in the time frame of initial HRV flight test programs because the technology of airborne computers will not be sufficiently advanced to support the computational loads required, or it is not desirable to perform the functions onboard in the flight test program for other reasons. Second, remote computational support either required or highly desirable to conduct flight testing itself was addressed. The use is proposed of an Automated Flight Management System which is described in conceptual detail. Third, autonomous operations is discussed and finally, unmanned operations.

Rediess, Herman A.↗
NASA NTRS1992

Shuttle entry aerothermodynamic flight research - The Orbiter Experiments (OEX) Program

Results of the OEX program are summarized with emphasis on the information on entry aerothermodynamic phenomena derived from Space Shuttle operations. The discussion focuses on OEX experiment complement and operational history, freestream environment and vehicle attitude data, aerodynamic force and moment data, aerodynamic surface data, and vehicle configuration data. Attention is also given to orbiter aerodynamic performance, stability and control, high-altitude atmospheric density variability, direct simulation Monte Carlo validation, orbital drag variation, and computational fluid dynamic technique validation.

Throckmorton, David A.↗
NASA NTRS1992

Estimation of the absolute position of mobile systems by an optoelectronic processor

A method that determine the absolute position of a mobile system with a hybrid optoelectronic processor has been developed. Position estimates are based on an analysis of circular landmarks that are detected by a TV camera attached to the mobile system. The difference between the known shape of the landmark and its image provides the information needed to determine the absolute position of the mobile system. For robust operation, the parameters of the landmark image are extracted at high speeds using an optical processor that performs an optical Hough transform. The coordinates of the mobile system are computed from these parameters in a digital co-processor using fast algorithms. Different sources of position estimation errors have also been analyzed, and consequent algorithms to improve the navigation performance of the mobile system have been developed and evaluated by both computer simulation and experiments.

Feng, Liqiang↗
NASA NTRS1996

A Comparison of Lifting-Line and CFD Methods with Flight Test Data from a Research Puma Helicopter

Four lifting-line methods were compared with flight test data from a research Puma helicopter and the accuracy assessed over a wide range of flight speeds. Hybrid Computational Fluid Dynamics (CFD) methods were also examined for two high-speed conditions. A parallel analytical effort was performed with the lifting-line methods to assess the effects of modeling assumptions and this provided insight into the adequacy of these methods for load predictions.

Bousman, William G.↗
NASA NTRS1959

A General Method for Automatic Computation of Equilibrium Compositions and Theoretical Rocket Performance of Propellants

A general computer program for chemical equilibrium and rocket performance calculations was written for the IBM 650 computer with 2000 words of drum storage, 60 words of high-speed core storage, indexing registers, and floating point attachments. The program is capable of carrying out combustion and isentropic expansion calculations on a chemical system that may include as many as 10 different chemical elements, 30 reaction products, and 25 pressure ratios. In addition to the equilibrium composition, temperature, and pressure, the program calculates specific impulse, specific impulse in vacuum, characteristic velocity, thrust coefficient, area ratio, molecular weight, Mach number, specific heat, isentropic exponent, enthalpy, entropy, and several thermodynamic first derivatives.

Gordon, Sanford↗
NASA NTRS2003

System Risk Assessment and Allocation in Conceptual Design

As aerospace systems continue to evolve in addressing newer challenges in air and space transportation, there exists a heightened priority for significant improvement in system performance, cost effectiveness, reliability, and safety. Tools, which synthesize multidisciplinary integration, probabilistic analysis, and optimization, are needed to facilitate design decisions allowing trade-offs between cost and reliability. This study investigates tools for probabilistic analysis and probabilistic optimization in the multidisciplinary design of aerospace systems. A probabilistic optimization methodology is demonstrated for the low-fidelity design of a reusable launch vehicle at two levels, a global geometry design and a local tank design. Probabilistic analysis is performed on a high fidelity analysis of a Navy missile system. Furthermore, decoupling strategies are introduced to reduce the computational effort required for multidisciplinary systems with feedback coupling.

Mahadevan, Sankaran↗
NASA NTRS2003

Computational Evaluation of the Steady and Pulsed Jet Effects on the Performance of a Circulation Control Wing Section

Circulation Control Wing (CCW) technology is a very effective way of achieving very high lift coefficients needed by aircraft during take-off and landing. This technology can also be used to directly control the flow field over the wing. Compared to a conventional high-lift system, a Circulation Control Wing (CCW) can generate the required values of lift coefficient C(sub L,max) during take-off/landing with fewer or no moving parts and much less complexity. Earlier designs of CCW configurations used airfoils with a large radius rounded trailing edge to maximize the lift benefit. However, these designs also produced very high drag. These high drag levels associated with the blunt, large radius trailing edge can be prohibitive under cruise conditions when Circulation Control is no longer necessary. To overcome this difficulty, an advanced CCW section, i.e., a circulation hinged flap was developed to replace the original rounded trailing edge CC airfoil. This concept developed by Englar is shown. The upper surface of the CCW flap is a large-radius arc surface, but the lower surface of the flap is flat. The flap could be deflected from 0 degrees to 90 degrees. When an aircraft takes-off or lands, the flap is deflected as in a conventional high lift system. Then this large radius on the upper surface produces a large jet turning angle, leading to high lift. When the aircraft is in cruise, the flap is retracted and a conventional sharp trailing edge shape results, greatly reducing the drag. This kind of flap does have some moving elements that increase the weight and complexity over an earlier CCW design. But overall, the hinged flap design still maintains most of the Circulation Control high lift advantages, while greatly reducing the drag in cruising condition associated with the rounded trailing edge CCW design. In the present work, an unsteady three-dimensional Navier-Stokes analysis procedure has been developed and applied to this advanced CCW configuration. The solver can be used in both a 2-D and a 3-D mode, and can thus model airfoils as well as finite wings. The jet slot location, slot height, and the flap angle can all be varied easily and individually in the grid generator and the flow solver. Steady jets, pulsed jets, the leading edge and trailing edge blowing can all be studied with this solver.

Liu, Yi↗
NASA NTRS2013

Simulating Effects of High Angle of Attack on Turbofan Engine Performance

A method of investigating the effects of high angle of attack (AOA) flight on turbofan engine performance is presented. The methodology involves combining a suite of diverse simulation tools. Three-dimensional, steady-state computational fluid dynamics (CFD) software is used to model the change in performance of a commercial aircraft-type inlet and fan geometry due to various levels of AOA. Parallel compressor theory is then applied to assimilate the CFD data with a zero-dimensional, nonlinear, dynamic turbofan engine model. The combined model shows that high AOA operation degrades fan performance and, thus, negatively impacts compressor stability margins and engine thrust. In addition, the engine response to high AOA conditions is shown to be highly dependent upon the type of control system employed.

Liu, Yuan↗
NASA NTRS2019

A common platform for DSN receiver development

NASA's Deep Space Network is currently updating a number of sub systems within the Signal Processing Centers at its Deep Space Communication Complexes in order to modernize aging equipment in the downlink receivers for telemetry, tracking, radio science, and radio astronomy. To reduce development costs and increase commonality among these traditionally custom-built receivers, the implementation team has developed a flexible architecture built primarily around commercial off-the-shelf hardware compliant with the Micro Telecommunications Computing Architecture (uTCA) specification and commercial high speed 10Gbit Ethernet switches. Custom firmware and software are being developed to perform the required signal processing functions needed to replace the legacy systems in a phased implementation approach which establishes a new digital Intermediate Frequency (IF) signal distribution system first, followed by implementations of various receiver functions as dictated by need. The first of these new receivers, the Open Loop Receiver, will come online in the Fall of 2018. A description of the new architecture, referred to as the “Common Platform”, will be provided followed by an overview of the phased implementation approach and initial OLR performance results.

Navarro, Robert↗
NASA NTRS1984

Initial experience with distributing structural calculations among computers operating in parallel

An existing program is currently being adapted to perform finite element analysis by distributing substructures over a network of four Apple IIe microcomputers connected to a shared disk. In this network, one microcomputer controls the entire process while the others perform the analysis on each substructure in parallel. This substructure analysis is used in an iterative, fully stressed, structural resizing procedure. This procedure allows experimentatation with resizing in which all analyses are not completed during a single iteration. This research gives some insight on how to configure multidiscriplinary analysis and optimization procedures for decomposable engineering systems using either high performance engineering workstations or a parallel processor supercomputer. In addition, the operational experience gained facilitates the implementation of analysis programs on these new computers when they become available in an engineering environment.

Rogers, J. L., Jr.↗
NASA NTRS1993

Analysis of a high speed civil transport configuration at subsonic flow conditions using a Navier-Stokes solver

Computations of three dimensional vortical flows over a generic High Speed Civil Transport (HSCT) configuration with an aspect ratio of 3.04 are performed using a thin-layer Navier-Stokes solver. The HSCT cruise configuration is modeled without leading or trailing edge flap deflections and without engine nacelles. The flow conditions, which correspond to tests done in the NASA Langley 8-Foot Transonic Pressure Tunnel (TPT), are a subsonic Mach number of 0.3 and Reynolds number of 4.4 million for a range-of-attack (-.23 deg to 17.78 deg). The effects of the farfield boundary location with respect to the body are investigated. The boundary layer is assumed turbulent and simulated using an algebraic turbulence model. The key features of the vortices and their interactions are captured. Grid distribution in the vortex regions is critical for predicting the correct induced lift. Computed forces and surface pressures compare reasonably well with the experimental TPT data.

Lessard, Victor R.↗
NASA NTRS1981

The Control Point Library Building System

The Earth Resources Observation System (EROS) Data Center in Sioux Falls, South Dakota distributes precision corrected Landsat MSS and RBV data. These data are derived from master data tapes produced by the Master Data Processor (MDP), NASA's system for computing and applying corrections to the data. Included in the MDP is the Control Point Library Building System (CPLBS), an interactive, menu-driven system which permits a user to build and maintain libraries of control points. The control points are required to achieve the high geometric accuracy desired in the output MSS and RBV data. This paper describes the processing performed by CPLBS, the accuracy of the system, and the host computer and special image viewing equipment employed.

Niblack, W.↗
NASA NTRS1982

Cost effective development of a Shuttle-based astronomical instrument control system

The high level language FORTH is used for the electronic control of the Space Shuttle-based Ultraviolet Imaging Telescope, in a flight computer system which minimizes costs. The greater part of the breadboard version of the flight computer is assembled from commercially available components, reducing novel circuit design features and permitting simultaneous development of both hardware and software. The commercial boards are then refabricated on aluminum core heat conducting stock, using high reliability parts to produce the flight versions of the system. The system's ground support equipment employs a MINC-25 minicomputer which performs such functions as flight computer software development, PROM programming, test and integration support, and flight operations support. The implementation of these concepts in flight computer telescope controls is described.

Parise, R. A.↗
NASA NTRS1991

A parallel-vector equation solver for unsymmetric matrices on supercomputers

A parallel-vector unsymmetric equation solver is presented. The solver exploits both vector and parallel capabilities provided by modern, high-performance supercomputers. A special storage scheme and loop-unrolling technique are used to optimize the vector performance. A parallel FORTRAN language is used to develop the solver on the CRAY 2 and CRAY Y-MP multiple processing computer environment. Three numerical examples are presented which demonstrate the efficiency and accuracy of this equation solver. The first two examples demonstrate the improved performance, and the third example utilizes the proposed solver to solve a highly nonlinear, unsymmetric finite element formulation for panel flutter.

Qin, J.↗