Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Lakeview, Oregon, Disposal Site

9.1 Compliance Summary The Lakeview, Oregon, Uranium Mill Tailings Radiation Control Act (UMTRCA) Title I Disposal Site was inspected September 16 and 17, 2015. Other than some ongoing concern with erosion-control rock riprap degradation, the disposal cell was in good condition. Some minor fence repairs and vegetation removal, and minor erosion repair work along the west site fence is planned. Inspectors identified no other maintenance needs or cause for a follow-up or contingency inspection. Disposal cell riprap is evaluated annually to ensure continued long-term protection of the cell from erosion during a severe precipitation event. Degradation of the rock riprap was first observed at the site in the mid-1990s. Rock gradation monitoring of the riprap on the west side slope has been performed as part of the annual inspection since 1997 to determine the mean diameter (D 50 ) value. As prescribed by the monitoring procedure, the rock monitoring is routinely conducted at random locations. However, at the U.S. Nuclear Regulatory Commission’s (NRC’s) request, the 2015 rock monitoring approach deviated from the normal procedure by using a pre-established monitoring grid in a subset area of the west side slope. This changed the monitoring approach from random sampling to biased sampling. The D 50 value measured during the 2015 gradation monitoring is 2.39 inches, which falls below the original D 50 design size range of 2.7–3.9 inches for the Type B size side slope riprap. At NRC’s request, rock durability monitoring was added to the gradation monitoring in 2009 to monitor durability by rock type. Results of the 2015 durability monitoring showed that74 percent of the total rock sampled is durability class code A rock with an assigned durability class of “highly durable” or durability class code B “durable” rock, and that over 90 percent of the 3-inch or larger rock is durability class code A or B. The rock durability classifications are further explained in Section 9.4.2.2.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Tensile and Microstructure Characterization of SNS Target Swirl Bubblers Fabricated by Additive Manufacturing

During operation the mercury facing surfaces of the Spallation Neutron Source target vessel are damaged by cavitation-induced erosion. One option to decrease the erosion damage to the SNS target vessel surfaces is to decrease the intensity of the pressure waves using small bubble mitigation. Injection of small diameter helium bubbles into mercury has been shown in decrease the intensity of proton-induced pressure waves and mitigate erosion damage to mercury/container interface surfaces. Several bubbler designs have been evaluated for implementation in the SNS target. One promising bubbler design is called a swirl bubbler, which is capable of producing a high density of very small diameter helium bubbles in flowing mercury. Due to the complexity of the swirl bubbler design and the geometric restrictions of conventional machining processes, additive manufacturing was considered for fabrication. But there was uncertainty with the mechanical properties of bubblers fabricated with additive manufacturing. A series of experiments were designed to characterize the tensile properties and microstructure of swirl bubblers fabricated using selective laser melting (SLM), both before and after consolidation via hot isostatic pressing (HIPing). This report summarizes the tensile and microstructural characterization of HIPed and non-HIPed swirl bubblers produced via the SLM process. The results show that the as-fabricated material contained appreciable porosity, lack-of-fusion defects, and inconsistent tensile properties with essentially zero ductility. But after a HIPing treatment the microstructure became fully consolidated, and the tensile properties surpassed the requirements specified in the material standard for steel-mill produced 316L plate material used to fabricate the SNS target vessel. While further testing is recommended to evaluate the material’s susceptibility to fatigue fracture, these results indicate 316L bubbler assemblies produced SLM and HIPed are promising candidates for implementation in a future SNS target module.

36 MATERIALS SCIENCE↗

Submittal of Solid Waste Management Units and Areas of Concern Annual Long-Term Monitoring and Maintenance Report for Calendar Year 2017

This SWMU and AOC Annual Long-Term Monitoring and Maintenance (LTMM) Report for Calendar Year 2017 (Annual LTMM Report) details the measures performed for 21 Solid Waste Management Units (SWMUs) and Areas of Concern (AOCs) at Sandia National Laboratories/New Mexico (SNL/NM) in accordance with the requirements of the “Long-Term Monitoring and Maintenance [LTMM] Plan for SWMUs and AOCs Granted Corrective Action Complete with Controls” in Attachment M of the Resource Conservation and Recovery Act Facility Operating Permit (Permit), which took effect February 26, 2015. This Annual LTMM Report does not present the measures for SWMU 76, Mixed Waste Landfill (MWL), as the applicable MWL reporting adheres to the approved MWL LTMM Plan, Section 4.8.1 and requires a separate annual report which will be submitted to the New Mexico Environment Department by June 30, 2018. Measures at these SWMUs and AOCs include surveillance of site conditions and maintenance of institutional controls. Conditions requiring maintenance or repair activities were identified at three of the inspected SWMUs and AOCs (SWMUs 45, 46, and 87) during the Permit-required annual site inspections. One SWMU identification sign located at SWMU 46 and two identification signs located at SWMU 87 were replaced due to weathered lettering. Evidence of erosion was observed at SWMU 45 during the annual site inspection; erosion controls will be implemented as needed to prevent the inadvertent exposure of hazardous wastes or hazardous waste constituents. SWMU 45 is located on the sloped border of Tijeras Arroyo south of Technical Area-IV. The erosion controls planned for the Tijeras Arroyo Escarpment will address not only SWMU 45, but also SWMUs 46 and 229 as a best management practice. SNL/NM personnel plan to complete this work in calendar year 2018. The status and progress of this project will be reported in the 2018 Annual SWMUs and AOCs Annual LTMM Report for Calendar Year 2018 to be submitted to the New Mexico Environment Department on March 31, 2019, as required by the Permit. Based upon the inspections performed and site conditions observed, the administrative and physical institutional controls in place at the SWMUs and AOCs are effectively providing continued protection of human health and the environment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

United States Department of Energy Sandia Natinoal Laboratories, California Arroyo Seco Improvement Program (Annual Report for 2021)

The Arroyo Seco Improvement Program (ASIP) is intended to provide active channel improvements and stream zone management activities that will reduce current flood and erosion risk while providing additional and improved habitat for critical species that may use the Arroyo Seco at the United States Department of Energy (DOE), Sandia National Laboratories, California (SNL/CA) location. The objectives of the ASIP are: correct existing channel stability problems associated with existing arroyo structures (i.e. bridges, security grates, utility crossings, and drain structures), correct bank erosion and provide protection against future erosion, reduce the risk of future flooding, and provide habitat improvement and creation of a mitigation credit for site development and management activities.

54 ENVIRONMENTAL SCIENCES↗

Assessment of the literature about Be-W mixed material layer formation in the fusion reactor environment

All plasma facing surfaces in a fusion reactor, whether initially pure or an alloy, will rapidly evolve into a mixed material due to plasma-induced erosion, migration and redeposition. Beryllium (Be) erosion from the main chamber, and its transport and deposition on to a tungsten (W) divertor results in the growth of mixed Be-W layers, which can evolve to form beryllides. These Be-W mixed materials exhibit generally less desirable properties than pure tungsten or pure beryllium, such as lower melting points. In order to better understand the parameter space for growth of these alloys, this paper reviews the literature on Be-W mixed material formation experiments—in magnetically confined fusion reactors, in linear plasma test stands, and during thin-film deposition—and on computational modeling of Be-W interactions, as well as briefly assesses the Be-W growth kinetics. We conclude that the following kinetic steps drive the material mixing: adsorption of the implanted/deposited ion on the metal surface; diffusion of the implanted/deposited ion from surface into the bulk, which is accelerated by defects; and loss of deposited material through erosion. Adsorption dominates (or prevents) material mixing in thin-film deposition experiments, whereas diffusion drives material mixing in plasma exposures due to the energetic ion implantation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

VitriEdge: Repairable & Durable Vitrimer Coatings for Wind Turbine Blade Leading Edges

The primary goal of this Level 1b incubator project was to explore the use of vitrimer coatings for repair of leading-edge erosion on end-of-life wind turbine blade surfaces, beyond coating strength of adhesion which has previously been demonstrated in the Level 1a project. Uniform vitrimer coatings (thickness: 400 µm) were applied to two end-of-life wind turbine blades for flexural, fatigue, and laminate tensile testing where the addition of the coating did not produce any statistical variation in tensile properties with minor drops in flexural strength for some laminate formulations. However, a <2% variation in storage modulus was measured for laminate structures (i.e., blade samples with vitrimer coatings) across 100,000 flexural cycles and upon laminate tensile failure, the vitrimer coatings displayed no visible signs of delamination. In addition, three methods to heal vitrimer coating damage was displayed: oven heating, addition of hot water, and a forced convection heat gun. All three heating and healing mechanisms demonstrated significant healing with scratch depths decreasing between 79-91% at healing times ranging between 1-min and 10-minutes. Finally, a water jet machine was used to simulate rain erosion for both the blade surfaces and vitrimer-coated blade surfaces where the diameter and depth of the damage was recorded as a function of exposure time, water pressure, height of exposure, and angle of exposure. Of interest, while the vitrimer coating did not significantly lessen the damage experienced during rain erosion, the addition of vitrimer composite coatings(5 wt.% mica addition) did result in a crack-resistant, durable coating capable of self-healing behavior and in all cases the angle of rain exposure was the most critical parameter explored. It is crucial to continue exploring this space where vitrimer coatings are of interest for both their self-healing properties and potential use as reversible adhesives.

17 WIND ENERGY↗

Antarctic permafrost processes and antiphase dynamics of cold-based glaciers in the McMurdo Dry Valleys inferred from 10 Be and 26 Al cosmogenic nuclides

Abstract. Soil and sediment mixing and associated permafrost processes are not widely studied or understood in the McMurdo Dry Valleys of Antarctica. In this study, we investigate the stability and depositional history of near-surface permafrost sediments to ∼ 3 m depth in the Pearse and lower Wright valleys using measured cosmogenic 10Be and 26Al depth profiles. In Pearse Valley, we estimate a minimum depositional age of ∼ 74 ka for the active layer and paleoactive-layer sediments (< 0.65 m). Combined depth profile modelling of 10Be and 26Al gives a depositional age for near-surface (< 1.65 m) permafrost in Pearse Valley of 180 +20/-40 ka, implying that the deposition of permafrost sediments predates MIS 5 advances of Taylor Glacier. Deeper permafrost sediments (> 2.09 m) in Pearse Valley are thus inferred to have a depositional age of > 180 ka. At a coastal, lower-elevation site in neighbouring lower Wright Valley, 10Be and 26Al depth profiles from a second permafrost core exhibit near-constant concentrations with depth and indicate the sediments are either vertically mixed after deposition or sufficiently young so that post-depositional nuclide production is negligible relative to inheritance. 26Al/10Be concentration ratios for both depth profiles range between 4.0 and 5.2 and are all lower than the nominal surface production rate ratio of 6.75, indicating that prior to deposition, these sediments experienced complex, yet similar, exposure–burial histories. Assuming a single-cycle exposure–burial scenario, the observed 26Al/10Be ratios are equivalent to a total minimum exposure–burial history of ∼ 1.2 Myr. In proximity to the depth profile core site, we measured cosmogenic 10Be and 26Al in three granite cobbles from thin, patchy drift (Taylor 2 Drift) in Pearse Valley to constrain the timing of retreat of Taylor Glacier. Assuming simple continuous exposure, our minimum, zero-erosion exposure ages suggest Taylor Glacier partially retreated from Pearse Valley no later than 65–74 ka. The timing of retreat after 65 ka and until the Last Glacial Maximum (LGM) when Taylor Glacier was at a minimum position remains unresolved. The surface cobble ages and permafrost processes reveal Taylor Glacier advances during MIS 5 were non-erosive or mildly erosive, preserving the underlying permafrost sediments and peppering boulders and cobbles upon an older, relict surface. Our results are consistent with U/Th ages from central Taylor Valley and suggest changes in moisture delivery over Taylor Dome during MIS 5e, 5c, and 5a appear to be associated with the extent of the Ross Ice Shelf and sea ice in the Ross Sea. These data provide further evidence of antiphase behaviour through retreat of a peripheral lobe of Taylor Glacier in Pearse Valley, a region that was glaciated during MIS 5. We suggest a causal relationship of cold-based glacier advance and retreat that is controlled by an increase in moisture availability during retreat of sea ice and perhaps the Ross Ice Shelf, as well as, conversely, a decrease during times of sea ice and Ross Ice Shelf expansion in the Ross Sea.

58 GEOSCIENCES↗

Optimization of electrostatic dual-grid beam-deflection system

Tests were performed to minimize accelerator grid erosion of a 5-cm diameter Kaufman ion thruster due to direct beam impingement. Several different screen hole diameters, pillow-shape-square screen holes, and dished screen grids were tried. The optimization was accomplished by copper plating the accelerator grid before testing each grid configuration on a thruster for a 2-hour run. The thruster beam sputtered copper and molybdenum from the accelerator grid where the beam impinged. The observed erosion patterns and measured accelerator currents were used to determine how to modify the accelerator system. The lowest erosion was obtained for a 50-percent open area pillow-shape-square-aperture screen grid, dished 0.043 centimeter convex toward the accelerator grid, which was positioned with the center of the screen grid 0.084 centimeter from the accelerator grid. During this investigation the accelerator current was reduced from 120 to 55 microamperes and was also more uniformly distributed over the area of the accelerator grid.

Hudson, W. R.↗

A 9700-hour durability test of a five centimeter diameter ion thruster

A modified Hughes SIT-5 thruster was life-tested at the Lewis Research Center. The final 2700 hours of the test are described with a charted history of thruster operating parameters and off-normal events. Performance and operating characteristics were nearly constant throughout the test except for neutralizer heater power requirements and accelerator drain current. A post-shutdown inspection revealed sputter erosion of ion chamber components and component flaking of sputtered metal. Several flakes caused beamlet divergence and anomalous grid erosion, causing the test to be terminated. All sputter erosion sources were identified.

Nakanishi, S.↗

Application of ERTS-1 data to the protection and management of New Jersey's coastal environment

The author has identified the following significant results. Rates of erosion and accretion of the shoreline are being calculated for two test areas along the New Jersey coast. Measurements are made on aerial photographs taken over the last 20 years and processed by computer. The rates are presented in graphic form on an ERTS-1 base map at a scale of 1:125,000. These rates are being used to determine the effectiveness of various shore protection structures at preventing sand removal and encouraging sand accumulation. Information on maintenance and construction expenditures is being used to obtain a cost effectiveness ratio for various shore protection devices. The relationship of erosion rates, property value, and project cost are all criteria for selection of site type and extent of a shore protection structure. Compilation and evaluation of historical data will identify past decision making patterns. The effectiveness of these decisions with respect to erosion rates, property value, and project cost, can be used as an added criteria for future allocation of money and the selection of site and type of structure to be built.

Yunghans, R. S.↗

Wind tunnel studies of Martian aeolian processes

Preliminary results are reported of an investigation which involves wind tunnel simulations, geologic field studies, theoretical model studies, and analyses of Mariner 9 imagery. Threshold speed experiments were conducted for particles ranging in specific gravity from 1.3 to 11.35 and diameter from 10.2 micron to 1290 micron to verify and better define Bagnold's (1941) expressions for grain movement, particularly for low particle Reynolds numbers and to study the effects of aerodynamic lift and surface roughness. Wind tunnel simulations were conducted to determine the flow field over raised rim craters and associated zones of deposition and erosion. A horseshoe vortex forms around the crater, resulting in two axial velocity maxima in the lee of the crater which cause a zone of preferential erosion in the wake of the crater. Reverse flow direction occurs on the floor of the crater. The result is a distinct pattern of erosion and deposition which is similar to some martian craters and which indicates that some dark zones around Martian craters are erosional and some light zones are depositional.

Greeley, R.↗

Water and processes of degradation in the Martian landscape

It is shown that erosion has been active on Mars so that many of the surface landforms are products of degradation. Unlike earth, erosion has not been a universal process, but one areally restricted and intermittently active so that a landscape is the product of one or two cycles of erosion and large areas of essentially undisturbed primitive terrain; running water has been the principal agent of degradation. Many features on Mars are most easily explained by assuming running surface water at some time in the past; for a few features, running water is the only possible explanation.

Milton, D. J.↗

A 9700-hour durability test of a five centimeter diameter ion thruster

A modified Hughes SIT-5 thrustor has been life-tested at the Lewis Research Center. The final 2700 hours of the test are described with a charted history of thrustor operating parameters and off-normal events. Performance and operating characteristics were nearly constant throughout the test except for neutralizer heater power requirements and accelerator drain current. A post-shutdown inspection revealed sputter erosion of ion chamber components and component flaking of sputtered metal. Several flakes caused beamlet divergence and anomalous grid erosion, causing the test to be terminated. All sputter erosion sources have been identified and promising sputter resistant components are currently being evaluated.

Nakanishi, S.↗

Operating characteristics of a hollow-cathode neutralizer for 5 and 8 centimeter-diameter electron bombardment mercury ion thrusters

Thin-tip 0.3-cm-outside-diameter hollow-cathode neutralizers were used to investigate causes of neutralizer tip erosion experienced in thruster endurance tests. Bell-jar tests indicated that neutralizers with new rolled tantalum foil inserts coated with an emissive mixture eroded very little over the neutral flow rates investigated (3 to 10 mA) for simulated 5- and 8-cm-diameter thruster neutralizer conditions. Tip erosion rates of neutralizers operated with no insert or emissive mixture increased by two orders of magnitude for both configurations as the neutral flow rate decreased. Spectroscopic analysis of the discharge plasma from neutralizers operated with inserts coated with the emissive mixture detected tungsten at all neutral flow rates for both thruster neutralizer conditions. The only source of tungsten was the tip. Therefore, detection of tungsten indicated neutralizer tip erosion. Barium, an element of the emissive mixture, was detected at low neutral flow rates for the 5-cm-diameter thruster neutralizer operating condition only.

Weigand, A. J.↗

Accelerated life test of sputtering and anode deposit spalling in a small mercury ion thruster

Tantalum and molybdenum sputtered from discharge chamber components during operation of a 5 centimeter diameter mercury ion thruster adhered much more strongly to coarsely grit blasted anode surfaces than to standard surfaces. Spalling of the sputtered coating did occur from a coarse screen anode surface but only in flakes less than a mesh unit long. The results were obtained in a 200 hour accelerated life test conducted at an elevated discharge potential of 64.6 volts. The test approximately reproduced the major sputter erosion and deposition effects that occur under normal operation but at approximately 75 times the normal rate. No discharge chamber component suffered sufficient erosion in the test to threaten its structural integrity or further serviceability. The test indicated that the use of tantalum-surfaced discharge chamber components in conjunction with a fine wire screen anode surface should cure the problems of sputter erosion and sputtered deposits spalling in long term operation of small mercury ion thrusters.

Power, J. L.↗

The use of color infrared photography for wetlands assessment

A study was undertaken of Pointe Mouillee Marsh, located on Lake Erie, to assess shoreline erosion and to inventory and evaluate adjacent land as potential replacement for areas lost to erosion, and to provide better data sources for management decisions. The results of the study were: (1) Evaluation of low altitude oblique photography was useful in determining specifications of operational mission requirements; (2) Accurate base map revisions, reflecting shoreline erosion, were made using aerial photography and a Zoom Transfer Scope; (3) An aerial land cover inventory provided data necessary for the selection of adjacent lands suitable for marshland development; (4) A detailed inventory of vegetative communities (mapped from CIR), was made for management decisions; and (5) A carefully selected and well laid-out transect was a key asset to photo interpretation and analysis of vegetation.

Enslin, W. R.↗

Micrometeoroid abrasion of lunar rocks - A Monte Carlo simulation

A Monte Carlo computer model simulating the randomness of the impact process both in space and in time is developed in order to provide insight into lunar rock erosion by single particle abrasion and into bombardment history of fractional surface areas of lunar rocks. Microcrater frequencies derived from lunar rocks are used to calculate magnitude and probability of each cratering event, and experimental cratering results are employed to determine the eroded volumina for individual crater sizes. It is shown that a fractional surface area of a lunar rock sample may have a completely different bombardment history, and that the exposure histories and actual erosion depths of the surfaces vary accordingly and are highly heterogeneous. A minimum erosion rate of 0.3 to 0.6 mm for the past one million years is obtained.

Hoerz, F.↗

Continued development of abradable gas path seals

Major program objectives were the continued development of NiCrAlY feltmetal and honeycomb systems for knife edge seal applications in the 1144 to 1366 K temperature range, and to initiate abradable seal material evaluation for blade tip seal applications in the 1366 to 1589 K temperature range. Larger fiber size, higher density feltmetal showed greatly improved erosion resistance with a slight reduction in abradability compared to the baseline feltmetal. Pack aluminide coating of the honeycomb extended the oxidation resistance and slightly improved the abradability of this material. Evaluation through selected abradability, erosion and oxidation testing, and pertinent metallography led to selection of a plasma sprayed yttria stabilized zirconia (ZrO2)/CoCrAlY layered system as the system with the most potential to meet the 1589 K requirement for blade tip seals. This system demonstrated structural integrity, erosion resistance, and some degree of abradability.

Shiembob, L. T.↗