Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELONGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Effects of rolling temperature and subsequent annealing on mechanical properties of ultrafine-grained Cu–Zn–Si alloy

The effects of rolling temperature and subsequent annealing on mechanical properties of Cu–Zn–Si alloy were investigated by using X-ray diffraction, transmission electron microscope, electron back scattered diffraction and tensile tests. The Cu–Zn–Si alloy has been processed at cryogenic temperature (approximately 77 K) and room temperature up to different rolling strains. It has been identified that the cryorolled Cu–Zn–Si alloy samples show a higher strength compared with those room temperature rolled samples. The improved strength of cryorolled samples is resulted from grain size effect and higher densities of dislocations and deformation twins. And subsequent annealing, as a post-heat treatment, enhanced the ductility. An obvious increase in uniform elongation appears when the volume fraction of static recrystallization grains exceeds 25%. The strength–ductility combination of the annealed cryorolled samples is superior to that of annealed room temperature rolled samples, owing to the finer grains, high fractions of high angle grain boundaries and twins. - Highlights: • An increase in hardness of Cu–Zn–Si alloy is noticed during annealing process. • Thermal stability is reduced in Cu–Zn–Si alloy by cryorolling. • An obvious enhancement in UE is noticed when fraction of SRX grains exceeds 25%. • A superior strength–ductility combination is achieved in the cryorolling samples.

36 MATERIALS SCIENCE↗

Dislocation density evolution of AA 7020-T6 investigated by in-situ synchrotron diffraction under tensile load

The dislocation density evolution along the loading axis of a textured AA 7020-T6 aluminum alloy during uniaxial tension was investigated by in-situ synchrotron diffraction. The highly parallel synchrotron beam at the High Energy Materials Science beamline P07 in PETRA III, DESY, offers excellent conditions to separate different influences for line broadening from which micro-strains are obtained using the modified Williamson–Hall method which is also for defect density investigations. During tensile loading the dislocation density evolution was documented from the as-received material (initial micro-strain state) to the relaxation of the strains during elastic deformation. After yield, the increasing rate of dislocation density growth was relatively fast till half-way between yield and UTS. After that, the rate started to decrease and the dislocation density fluctuated as the elongation increased due to the generation and annihilation of dislocations. When dislocation generation is dominant, the correlation between the flow stress and dislocation density satisfies the Taylor equation. Besides, a method to correct the thickness effect on peak broadening is developed in the present study. - Highlights: • In-situ synchrotron diffraction was applied to characterize peak broadening. • Dislocation evolution along the loading axis during uniaxial tension was investigated. • A method to correct the sample thickness effect on peak broadening was developed. • Dislocation density and flow stress satisfy the Taylor equation at a certain range. • The texture before load and after sample fracture was analyzed.

36 MATERIALS SCIENCE↗

The effect of scandium addition on microstructure and mechanical properties of Al–Si–Mg alloy: A multi-refinement modifier

Effect of scandium (Sc) additions on the microstructure, mechanical properties and fracture behavior of Al–Si–Mg casting alloy (F357) were systematically investigated. It was found that Sc addition caused a multi-refining efficiency on the microstructure of as-cast F357 alloy, including refinement of grains and secondary dendrite arm spacing (SDAS), modification of eutectic Si and harmless disposal of β-Al{sub 5}FeSi phase. Subsequent T6 heat treatment had further induced the complete spheroidization of eutectic Si and precipitation of fine secondary Al{sub 3}Sc dispersoids in the Sc modified alloys. Thus the mechanical properties, especially the ductility, were significantly enhanced by the addition of Sc combined with the heat treatment. The highest ultimate tensile strength, yield strength and elongation were achieved in 0.8 wt.% Sc modified F357 alloy combined with T6 heat treatment. Furthermore, fractographic examinations indicated that the ductile fracture mechanism served as a dominate role in the modified alloys due to the formation of fine, deep and uniformly distributed dimples. - Highlights: • Detailed characterization of the multi-refining microstructure of Sc modified F357 alloy was performed. • The multi-refinement was proposed to refine grain and SDAS, modify eutectic Si and β-phase. • Sc modifier combined with T6 treatment is effective in improving tensile properties. • Modification of eutectic Si in F357 alloy with Sc is consistent with the IIT mechanism.

36 MATERIALS SCIENCE↗

Study of retained austenite and nano-scale precipitation and their effects on properties of a low alloyed multi-phase steel by the two-step intercritical treatment

Microstructure evolution and properties were studied in a low carbon low alloyed hot-rolled bainitic steel by annealing and annealing plus tempering. Microstructure of the hot-rolled steel consists of lath bainite and martensite. By annealing at 720 °C for 30 min and water quenching, multi-phase microstructure consisting of intercritical ferrite, tempered bainite/martensite, retained austenite and fresh martensite was obtained. With increasing annealing temperature to 760 °C, microstructure of the steel consisted of intercritical ferrite, fresh martensite without retained austenite. After the second step of tempering at 680 °C for samples annealed both at 720 °C and 760 °C, ~ 8–9% volume fraction of retained austenite was obtained in the multi-phase microstructure. Moreover, fine precipitates of VC with size smaller than 10 nm and copper precipitates with size of ~ 10–50 nm were obtained after tempering. Results from scanning transmission electron microscopy (STEM) give evidence to support that the partitioning of Mn, Ni and Cu is of significance for retained austenite stabilization. Due to the combined contribution of multiphase microstructure, the transformation-induced-plasticity effect of retained austenite and strengthening effect of nanometer-sized precipitates, yield strength greater than 800 MPa, yield to tensile ratio of 0.9, uniform elongation of ~ 9% and good low temperature impact toughness of 147 J at − 40 °C were achieved. - Highlights: • Stable retained austenite was produced in a low alloyed steel. • Partition of Mn, Ni and Cu was confirmed by STEM for austenite stabilization. • Nano-sized VC and Cu precipitates were achieved by second tempering. • High strength–high toughness with low Y/T ratio was obtained.

36 MATERIALS SCIENCE↗

Tensile and high cycle fatigue behaviors of high-Mn steels at 298 and 110 K

Tensile and high cycle fatigue behaviors of high-Mn austenitic steels, including 25Mn, 25Mn0.2Al, 25Mn0.5Cu, 24Mn4Cr, 22Mn3Cr and 16Mn2Al specimens, were investigated at 298 and 110 K. Depending on the alloying elements, tensile ductility of high-Mn steels either increased or decreased with decreasing temperature from 298 to 110 K. Reasonable correlation between the tendency for martensitic tranformation, the critical twinning stress and the percent change in tensile elongation suggested that tensile deformation of high-Mn steels was strongly influenced by SFE determining TRIP and TWIP effects. Tensile strength was the most important parameter in determining the resistance to high cycle fatigue of high-Mn steels with an exceptional work hardening capability at room and cryogenic temperatures. The fatigue crack nucleation mechanism in high-Mn steels did not vary with decreasing tempertature, except Cr-added specimens with grain boundary cracking at 298 K and slip band cracking at 110 K. The EBSD (electron backscatter diffraction) analyses suggested that the deformation mechanism under fatigue loading was significantly different from tensile deformation which could be affected by TRIP and TWIP effects. - Highlights: •The resistances to HCF of various high-Mn steels were measured. •The variables affecting tensile and HCF behaviors of high-Mn steels were assessed. •The relationship between tensile and the HCF behaviors of high-Mn steels was established.

36 MATERIALS SCIENCE↗

A novel ultrafine-grained Fe−22Mn−0.6C TWIP steel with superior strength and ductility

A fully recrystallized ultrafine-grained (UFG) Fe−22wt.%Mn−0.6wt.%C twinning-induced plasticity (TWIP) steel with mean grain size of 576 nm was fabricated by cold rolling and annealing process. Tensile test showed that this UFG steel possessed high yield strength of 785 MPa, and unprecedented uniform elongation of 48%. The Hall-Petch relationship was verified from the coarse-grained (CG) regime to the ultrafine-grained (UFG) regime. The microstructures at specified tensile strains were characterized by electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM). The microstructures and strain hardening behavior of the UFG TWIP steel were compared with the CG counterpart. The strong strain hardening capability of the UFG steel is supposed to be responsible for the high strength and good ductility. - Highlights: • A fully recrystallized Fe−22Mn−0.6C TWIP steel with mean grain size of 576 nm was fabricated. • The ultrafine-grained (UFG) steel exhibits strong strain-hardening capability, excellent strength and ductility. • The Hall-Petch relationship is fitted well from the CG regime to the UFG regime.

36 MATERIALS SCIENCE↗

Effects of cold predeformation on dissolution of second-phase Al2Cu particles during solution treatment of 2219 Al-Cu alloy forgings

Highlights: • Cold predeformation (CPD) was performed on 2219 Al-Cu alloy forgings. • CPD promoted the dissolution of coarse Al{sub 2}Cu particles during solution treatment. • CPD increased the driving force to precipitate θ′ phases during aging treatment. • Increasing CPD improved the tensile properties of the forgings. - Abstract: Cold predeformation (CPD, before solution treatment) at different pre-compressing deformations of 0, 5, and 10% was performed on 2219 Al-Cu alloy forgings, and its effect on the dissolution of second-phase Al{sub 2}Cu particles during solution treatment was investigated. The results indicated that a higher number of coarse Al{sub 2}Cu particles dissolved in the Al matrix during solution treatment in samples processed with CPD. Upon increasing CPD from 0 to 10%, the area fraction of the coarse particles decreased from 2.57 to 0.57%, while their mean size decreased from 12.5 to 8.7 μm. The corresponding driving force for precipitation during the subsequent aging treatment process increased, the main precipitates in the material transitioned from the θ″ phase to the θ′ phase, and the area fraction of the precipitates increased from 6.1 to 18.1%. As a result, a significant increase in ultimate tensile strength (by 61.2 MPa), yield strength (by 63.2 MPa), and tensile elongation (by 2.2%) was obtained.

36 MATERIALS SCIENCE↗

Pulse current auxiliary forging of sintered TiAl alloys based on the investigation of dynamic recrystallization and phase transformation

Highlights: • DRX kinetics model of sintered near γ TiAl alloy was established. • DRX process was accompanied by twinning when compressed at 1125 °C/0.1 s{sup − 1}. • Hot deformation has a promotion to the phase transformation of γ → α. - Abstract: Pulse current auxiliary forging is a new and efficient way to fabricate high performance TiAl based alloys. Dynamic recrystallization (DRX) and phase transformation have a pronounced effect on the subsequent deformability of TiAl based alloys. Hence, the dynamic recrystallization kinetics were determined at the temperature range of 1125–1275 °C and strain rate range of 0.1–0.001 s{sup − 1}. In addition, the DRX mechanism and phase transformation of TiAl based alloys were investigated to model the microstructure evolution in order to provide guidance for the pulse current auxiliary forging process. When the specimens were compressed at 1125 °C/0.1 s{sup − 1}, twinning played an important role in the DRX process. With increasing deformation temperature, the microstructure transformed from near gamma into duplex microstructure. In addition, according to the kinetics of dynamic recrystallization and phase transformation, fully DRXed TiAl based alloys were fabricated through pulse current auxiliary forging. The as-forged TiAl-based alloys show good superplastic performance with an elongation over 410%.

36 MATERIALS SCIENCE↗

Effect of microstructure on exfoliation corrosion resistance in an Al-Zn-Mg alloy

Highlights: • A quantitative method was proposed to characterize EXCO resistance. • The EXCO product lead to strain in ND and elongation in RD on nearby grains. • Recrystallized grains are more susceptible to EXCO than fibrous grains. • High fraction of high-angle grain boundaries reduces EXCO resistance. • High coverage ratio of η phases on high-angle grain boundaries reduces EXCO resistance. - Abstract: In this work, the effect of microstructure on exfoliation corrosion (EXCO) resistance in an Al-Zn-Mg alloy were investigated using standard EXCO test, together with detailed microstructural examinations mainly by scanning electron microscopy (SEM) and high-angle annular detector dark-field scanning transmission electron microscopy (HAADF-STEM). An EXCO product model was built based on morphologies of EXCO product on longitudinal section and cross section for further measurement and analysis. A quantitative characterization of EXCO resistance by measuring average thickness of EXCO product was conducted, showing average results of 6.94 μm, 10.21 μm and 18.14 μm, which are corresponding to EXCO ratings of P, EA and EB under ASTM G34 standard, respectively. It was concluded that recrystallization, high fraction of high-angle grain boundaries (HAGBs) and high coverage ratio of η phases on HAGBs reduced EXCO resistance.

36 MATERIALS SCIENCE↗

Ensuring combination of strength, ductility and toughness in medium-manganese steel through optimization of nano-scale metastable austenite

Highlights: • Medium-Mn steel was innovatively designed for medium to heavy steel plates. • Three intercritical annealing processes were adopted to ensure TRIP effect. • Austenite-martensite submicro-laminate structure was obtained after annealing. • The reversed austenite with different stability led to improved ductility. • TRIP effect induced by metastable austenite contributed excellent impact properties. - Abstract: Medium-Mn steel was innovatively designed in terms of alloying elements for medium to heavy steel plates to obtain combination of high strength, good ductility, and excellent low temperature toughness. Martensite was the dominant microstructure in the directly quenched steel plate because of high hardenability obtained by the addition of 5.6 wt% Mn. Three intercritical annealing processes were adopted to ensure transformation-induced-plasticity (TRIP) effect through optimization of the volume fraction, morphology, and C and Mn-enriched reversed austenite. On annealing, the dislocation density of martensite plate was decreased because of recovery and recrystallization, and metastable austenite film nucleated at the interface. Both thermal and mechanical stability of austenite decreased with increase in annealing temperature. The high yield strength of 840 MPa, good elongation after fracture of 24.3%, and excellent toughness at − 60 °C of 130.3 J was obtained at intermediate annealing temperature of 650 °C, and the volume fraction of reversed austenite at room temperature and − 80 °C was 22% and 17%, respectively. The reversed austenite exhibited different stability with increased tensile strain, leading to improved ductility and delayed necking. Moreover, the crack initiation energy and crack propagation energy were increased via dynamic stress partitioning and relaxation together with the transformation of metastable austenite. Thus, significant degree of TRIP effect induced by moderate stability of austenite played an important role in governing mechanical properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of Bi on the microstructure and mechanical properties of Sn-Zn alloys processed by rolling

Highlights: • Sn-Zn-Bi is proposed for the first time as the cladding in linear explosive device. • Bi can significantly refine the microstructure of Sn-Zn. • Bi can enhance both strength and ductility of Sn-Zn processed by rolling. • The 5 wt% Bi in Sn-3Zn leads to finest and most homogenous grains after rolling. - Abstract: Sn-Zn based alloys including Sn-3Zn, Sn-3Zn-1Bi, and Sn-3Zn-5Bi were prepared by casting and rolling, in efforts to assess their feasibility for the application as cladding materials in detonating and explosive cords. It was found that Bi significantly refined the solidification microstructure, changing the configuration of Sn-Zn eutectic from well-aligned Zn-rich precipitates/needles to misaligned Zn-rich flakes. During deformation, second phases like Zn-rich precipitates and Bi particles, and Bi solutes were effective in grain refinement since second phase particles provided more sites for nucleation and more obstacles to growth of new recrystallized grains. Tensile results revealed that Bi addition enhanced both strength and ductility of the rolled Sn-Zn-Bi alloys. The Sn-3Zn-5Bi alloy possessed superior strength and ductility (UTS: 84.4 MPa; Yield strength: 68.3 MPa; Elongation: 75.2%) due to its finest and most homogeneous equiaxed grains. Based on decent mechanical properties, the Sn-Zn-Bi alloys could be well qualified for the application as cladding materials.

36 MATERIALS SCIENCE↗

Enhancing the tensile properties of EBM as-built thin parts: Effect of HIP and chemical etching

Highlights: • The EBM process leads to important cross section variations in thin parts. • Stress calculation must be based on the average section in order to be relevant. • As-built state has a detrimental effect on every mechanical property. • Mechanical properties of machined samples are met with chemical etching. • HIP has a beneficial effect on the ductility. - Abstract: As-built Ti-6Al-4 V thin parts were manufactured using Electron Beam Melting (EBM) and characterized by optical microscopy and laboratory X-ray tomography in order to observe their microstructure, pore distribution and surface aspect. Chemical etching and HIP post-treatments were applied to as-built samples and their effect on the material and static mechanical properties were studied. Tensile tests were performed on both as-built and post-treated samples and their results compared to the ones reported in the literature for machined EBM samples. Because of the significant variations of the cross section observed along the gauge length, the calculation of the tensile stresses is not straightforward. Three simple sections were measured from the tomography scans. The average section along the gauge length was considered as the most suitable. The tensile mechanical properties of the as-built samples were studied and a detrimental effect of the surface state on the yield strength, ultimate tensile strength and elongation to failure was observed. Smoothing of the surface irregularities induced by chemical etching provoked an increase of those mechanical properties whereas the change of the microstructure generated by the HIP treatment leads to a decrease of the material strength that goes along with an increase of the ductility. Down scaling factors were proposed in order to take into account the sample state, as-built or post-treated.

36 MATERIALS SCIENCE↗

Influence of annealing temperature on microstructure and tensile property of cold-rolled Fe-0.2C-11Mn-6Al steel

To fully realize the potential of austenite characterized by strip-like and equiaxed structure and enhance the comprehensive mechanical properties of medium-Mn steel, the as-hot-rolled Fe-0.2C-11Mn-6Al steel was subjected to cold roll annealing to refine the grain size. The ultimate tensile strength of the cold-rolled steel annealed at 650 °C was significantly enhanced, while the total elongation was markedly decreased. The variation in tensile properties of the annealed cold-rolled steel was due to weakening of transformation induced plasticity (TRIP) effect and enhanced twinning induced plasticity (TWIP) effect with increase in quenching temperature. Furthermore, austenite had two different morphologies, strip-like and granular. Though the grain size of granular austenite increased with increased annealing temperature, the austenite stability increased with increase in quenching temperature, which is contrary to the expectations. This is attributed to refinement of large austenite strips induced by recrystallization.

36 MATERIALS SCIENCE↗

Interfacial design and strengthening mechanisms of AZ91 alloy reinforced with in-situ reduced graphene oxide

Highlights: • An in-situ process was developed to synthesize magnesium alloy composite reinforced by graphene. • Microstructure and phase composition of oxide films were investigated by OM, SEM, EDS and XRD analysis. • The interfacial structure of Mg composites reinforced with reduced graphene oxide was characterized. • The interfacial reaction mechanisms between GO (graphene oxide) and the Mg metal was studied. - Abstract: This work highlights to develop an in-situ process to disperse uniformly graphene possessing good interfacial bonds with the matrix of Mg alloy. A homogeneous distribution of graphene in the matrix has been successfully obtained through in-situ reduction of graphene oxide (RGO) by sintering process after the graphene oxide (GO) was uniformly dispersed in AZ91 powders. The interface product nano-sized MgO can significantly improve the interfacial bonding strength between RGO and α-Mg with analysis by transmission electron microscopy. The orientation relationships of ( 2-bar 00){sub MgO}//( 1-bar 10 2-bar ){sub α‐Mg} and [011]{sub MgO}//[2 4-bar 2 3-bar ]{sub α‐Mg} with the semi-coherent interface characteristics were clarified for the first time at the interface of MgO/α-Mg, suggesting a good lattice space matching. By employing such process, a composite containing 0.5 wt% of GO shows an 85.7% and 61.4% increase in yield strength and elongation, respectively, over unreinforced AZ91 alloy. The underlying strengthening mechanisms of in-situ reduced graphene oxide are discussed in detail.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microstructure, texture and mechanical properties of AA 1060 aluminum alloy processed by cryogenic accumulative roll bonding

Highlights: • The Al sheets were accumulative roll bonded to five cycles at cryogenic temperature. • The microstructure, texture and mechanical properties of ARB sheets were investigated. • The texture evolution at surface layer was quantified by mathematical formulae. • The strength of the β fiber at center layer was affected by the initial texture and the strain. - Abstract: AA 1060 aluminum alloy sheet was processed to five accumulative roll bonding (ARB) cycles at cryogenic temperature. The microstructure, texture and mechanical properties of the ARB processed sheets were investigated. The results show that the surface layer of the ARB processed sheets exhibits a significant r-cube shear texture. Initial cube orientation at the surface layer was gradually rotated to the r-cube orientation during the ARB process, leading to the increase in the strength of the r-cube shear texture with ARB cycles. The texture evolution at the surface layer was quantified in terms of a simple relation between the texture volume fractions and accumulated true strain. The strength of the β fiber rolling texture and the distribution of orientation intensities along the β fiber at the center layer were strongly affected by the initial texture. As the ARB cycles increased, the initial texture was changed from the cube texture to the r-cube texture, leading to a continuous increase in the strength of the β fiber rolling texture dominated by the C orientation. The yield and ultimate tensile strength of the ARB processed sheets increased markedly after the first ARB cycle and then increased slowly with increasing ARB cycles, while the elongation decreased accordingly.

36 MATERIALS SCIENCE↗

Modification of eutectic Mg2Si in AlMg5Si2Mn alloy by pre-homogenization deformation treatment with different reduction conditions

Highlights: • PHD treatment was proposed to modify Mg{sub 2}Si morphology of extruded AlMg5Si2Mn alloy. • PHD treatment accelerated spheroidization of eutectic Mg{sub 2}Si in AlMg5Si2Mn alloy. • Tensile properties of AlMg5Si2Mn extrudates were improved by introduction of PHD. - Abstract: The effect of a novel pre-homogenization deformation (PHD) treatment on the microstructure and mechanical properties of extruded AlMg5Si2Mn alloy was investigated. By introducing the cold compression prior to homogenization treatment, the brittle and interconnected eutectic Mg{sub 2}Si phase in the as-cast AlMg5Si2Mn alloy transformed into fine and spherical particles uniformly dispersed in the aluminum matrix. As the amount of PHD increased, up to 10%, the size of the Mg{sub 2}Si particles decreased and their sphericity increased in the extruded samples, resulting in a gradual increase in both strength and elongation after heat treatment. The mechanical properties of the PHD-treated AlMg5Si2Mn extrudates were compared with those of materials prepared using various casting and deformation processes, and the potential application to wrought products was discussed.

36 MATERIALS SCIENCE↗

Enhanced strength and toughness in ultra-fine grained 99.9% copper obtained by cryo-hydrostatic extrusion

Highlights: • Cryo-HE can increase the yield strength of Cu by more than threefold. • In cryo-HE of Cu, the grain refinement is stronger by 30% than in room-HE. • Cryo-HE with post-annealing effectively creates a bimodal microstructure in Cu. • Short-term post-annealing applied to cryo-HE-treated Cu can double its ductility. • Grain refinement with recrystallization results in a slight increase of Cu toughness. - Abstract: Ultrafine grained 99.9% Cu with enhanced strength and toughness was produced by hydrostatic extrusion conducted at the temperature of liquid nitrogen. The cryo-extruded Cu has a tensile yield strength of 490 MPa, hardness of 145 HV0.2, and tensile fracture toughness of 39.5 MPa m{sup 1/2}, which means that their values increased by 380%, 185% and ~10%, respectively, compared to those of the starting material. The significant strengthening is due to the strong grain refinement to 320 nm and the high energy of defects stored during the processing at liquid nitrogen temperature. The short term post deformation annealing doubles the ductility of material even by above 10% of the elongation to fracture at a slight expense of the yield strength (485 MPa). The observed behavior of Cu can be explained in terms of its low stacking fault energy, the susceptibility to dynamic recrystallization within the working zone of the extrusion die, and the triaxial strain components with the very large strain gradients, combined with the significant adiabatic heating effect active during the hydrostatic extrusion. The better homogeneity of the grain refinement and the higher efficiency of the distribution of defects and of the energy storage accompanied by the decreased dislocation mobility during the cryo hydrostatic extrusion contributed to the higher strength.

36 MATERIALS SCIENCE↗

Deformation and fracture characteristics of Al6092/SiC/17.5p metal matrix composite sheets due to heat treatments

Highlights: • Al{sub 2}Cu, Al{sub 4}Cu{sub 2}Mg{sub 8}Si{sub 7} and MgAl{sub 2} precipitations are formed between Al-matrix and SiC particle interface after T6-treatement • O-condition annealing decrease Al{sub 2}Cu intermetallic compound and increase elongation to fracture • 6092Al/SiCp composite at O-condition annealing is more sensitive to strain rate than the one heat treated by T6-treatment • Dimple density in the fracture surface of Al/SiCp composite varies as a function of heat treatment and strain rate - Abstract: In metal matrix composite (MMC) materials, the reaction between the metal matrix and reinforcement particles could change the composition of the matrix and the interface and lead to interfacial compounds. These intermetallic compounds may have either a deleterious effect to the mechanical properties or beneficial effect in enhancing the toughness and ductility of the composite. An aluminium 6092 alloy with 17.5% volume fraction silicon carbide (SiC) particles sheet manufactured by means of powder metallurgical method, heat treated to T6 condition, is used to obtain a fundamental understanding of the heat treatment effect on the fracture mechanism, the microstructural changes and the interface between the Al-matrix and SiC particles. Changes in the microstructure of the Al/SiCp and the topography of the fracture are investigated using scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDS) and transmission electron microscopy (TEM) to characterize the precipitate and intermetallic compounds formed at the Al/Sic interface. X-ray diffraction (XRD) is utilized to characterize the phase formation and to give confidence in the results of TEM and EDS. Tensile tests with different strain rates (8 × 10{sup −5}, 8 × 10{sup −4}, 8 × 10{sup −3}, 8 × 10{sup −2} and 0.16 s{sup −1}) were carried out to study the toughness and to find a correlation between the strain rate and heat treatment. Under T6 condition, the results show that the mechanical property of this MMC is less ductile due to the formation of precipitations as a result of either the interaction between the Al and SiCp or from hardening precipitation treatment, e.g. Al{sub 2}Cu, Al{sub 4}Cu{sub 2}Mg{sub 8}Si{sub 7} and MgAl{sub 2}. O-condition annealing can reduce the detrimental effect of the intermetallic compounds in the interface region and improve the toughness and ductility of the material by decreasing the intermetallic compound (Al{sub 2}Cu). However, the Al/SiC sheet treated with O-condition annealing is more sensitive to the strain rate than the one treated with T6.

36 MATERIALS SCIENCE↗