Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Modeling and Simulation of Compression Molding Process for Sheet Molding Compound (SMC) of Chopped Carbon Fiber Composites

Compression molded SMC composed of chopped carbon fiber and resin polymer which balances the mechanical performance and manufacturing cost presents a promising solution for vehicle lightweight strategy. However, the performance of the SMC molded parts highly depends on the compression molding process and local microstructure, which greatly increases the cost for the part level performance testing and elongates the design cycle. ICME (Integrated Computational Material Engineering) approaches are thus necessary tools to reduce the number of experiments required during part design and speed up the deployment of the SMC materials. As the fundamental stage of the ICME workflow, commercial software packages for SMC compression molding exist yet remain not fully validated especially for chopped fiber systems. In this study, SMC plaques are prepared through compression molding process. The corresponding simulation models are built in Autodesk Moldflow with the same part geometry and processing conditions as in the molding tests. The output variables of the compression molding simulations, including press force history and fiber orientation of the part, are compared with experimental data. Influence of the processing conditions to the fiber orientation of the SMC plaque is also discussed. It is found that generally Autodesk Moldflow can achieve a good simulation of the compression molding process for chopped carbon fiber SMC, yet quantitative discrepancies still remain between predicted variables and experimental results.

36 MATERIALS SCIENCE↗

Application of Al-Cu-W-Ta graded density impactors in dynamic ramp compression experiments

Graded density impactors (GDIs) are utilized to dynamically compress materials to extreme conditions. Two modifications to a previously developed Mg-Cu-W GDI are made in this work before using it in a dynamic compression experiment: Mg is replaced with Al and a Ta disk is glued to the back. The Mg phase is replaced by Al because FCC Al remains solid to higher pressure along its Hugoniot compared to Mg. The addition of the Ta disk creates a constant particle velocity regime and facilitates a definition of peak pressure states. Microstructure analysis, profilometry, and ultrasonic C-scans of the Al-Cu-W GDI all confirm excellent uniformity. We evaluated signal variation in the radial direction of a dynamically compressed Al-LiF bilayer target to evaluate the contribution of spatial nonuniformity to errors. Velocity traces from five photon Doppler velocimetry (PDV) probes located at different radial distances from the center of the target varied at most by 1.1% with a root mean square of 0.3% during the compression ramp, demonstrating low PDV measurement error over a relatively large experimental area. The experimental PDV data additionally agrees well with 1D simulations that use inputs from predictive characterization models developed for the material properties resulting from tape casting, laminating, and powder consolidation processes. Low measurement error during quasi-isentropic compression, leading to better precision, promises a robust platform to reach extreme compression and low-temperature recovery states and facilitates discovery via synthesis, quenching, and preservation of new high-pressure phases.

36 MATERIALS SCIENCE↗

Numerical assessment of the role of slip and twinning in magnesium alloy AZ31B during loading path reversal

Magnesium alloy AZ31B plastically deforms via twinning and slip. Corresponding to the unidirectional nature of twinning, the activity of twinning/detwinning is directly related to loading history and materials texture. Using the elastic viscoplastic self-consistent model implementing with the twinning and detwinning model (EVPSC–TDT), we revisited experimental data of AZ31B sheets under four different strain paths: (1) tension–compression–tension along rolling direction, (2) tension–compression–tension along transverse direction, (3) compression–tension–compression along rolling direction, and (4) compression–tension–compression along transverse direction, and identified the dominant deformation mechanisms with respect to the strain path. We captured plastic deformation behaviors observed in experiments and quantitatively interpreted experimental observations in terms of the activities of different deformation mechanisms and the evolution of texture. It is found that the in-plane pre-tension has slight effect on the subsequent deformation, and the pre-compression and the reverse tension after compression have significant effect on the subsequent deformation. The inelastic behavior under compressive unloading is found to be insignificant at a small strain level but pronounced at a large strain level. Lastly, such significant effect is mainly ascribed to the activity of twinning and detwinning.

36 MATERIALS SCIENCE↗

Incidence and Treatment Patterns in Hospitalizations for Malignant Spinal Cord Compression in the United States, 1998-2006

Purpose: To characterize patterns in incidence, management, and costs of malignant spinal cord compression (MSCC) hospitalizations in the United States, using population-based data. Methods and Materials: Using the Nationwide Inpatient Sample, an all-payer healthcare database representative of all U.S. hospitalizations, MSCC-related hospitalizations were identified for the period 1998-2006. Cases were combined with age-adjusted Surveillance, Epidemiology and End Results cancer death data to estimate annual incidence. Linear regression characterized trends in patient, treatment, and hospital characteristics, costs, and outcomes. Logistic regression was used to examine inpatient treatment (radiotherapy [RT], surgery, or neither) by hospital characteristics and year, adjusting for confounding. Results: We identified 15,367 MSCC-related cases, representing 75,876 hospitalizations. Lung cancer (24.9%), prostate cancer (16.2%), and multiple myeloma (11.1%) were the most prevalent underlying cancer diagnoses. The annual incidence of MSCC hospitalization among patients dying of cancer was 3.4%; multiple myeloma (15.0%), Hodgkin and non-Hodgkin lymphomas (13.9%), and prostate cancer (5.5%) exhibited the highest cancer-specific incidence. Over the study period, inpatient RT for MSCC decreased (odds ratio [OR] 0.68, 95% confidence interval [CI] 0.61-0.81), whereas surgery increased (OR 1.48, 95% CI 1.17-1.84). Hospitalization costs for MSCC increased (5.3% per year, p < 0.001). Odds of inpatient RT were greater at teaching hospitals (OR 1.41, 95% CI 1.19-1.67), whereas odds of surgery were greater at urban institutions (OR 1.82, 95% CI 1.29-2.58). Conclusions: In the United States, patients dying of cancer have an estimated 3.4% annual incidence of MSCC requiring hospitalization. Inpatient management of MSCC varied over time and by hospital characteristics, with hospitalization costs increasing. Future studies are required to determine the impact of treatment patterns on MSCC outcomes and strategies for reducing MSCC-related costs.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

High pressure melting curves of silver, gold and copper

In this work, based on the Lindemann's formula of melting and the pressure-dependent Grüneisen parameter, we have investigated the pressure effect on melting temperature of silver, gold and copper metals. The analytical expression of melting temperature as a function of volume compression has been derived. Our results are compared with available experimental data as well as with previous theoretical studies and the good and reasonable agreements are found. We also proposed the potential of this approach on predicting melting of copper at very high pressure.

36 MATERIALS SCIENCE↗

Effect of Mach number on the efficiency of microwave energy deposition in supersonic flow

The article is devoted to experimental and numerical studies of the efficiency of microwave energy deposition into a supersonic flow around the blunt cylinder at different Mach numbers. Identical conditions for energy deposition have been kept in the experiments, thus allowing to evaluate the pure effect of varying Mach number on the pressure drop. Euler equations are solved numerically to model the corresponding unsteady flow compressed gas. The results of numerical simulations are compared to the data obtained from the physical experiments. It is shown that the momentum, which the body receives during interaction of the gas domain modified by microwave discharge with a shock layer before the body, increases almost linearly with rising of Mach number and the efficiency of energy deposition also rises.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Note: The performance of new density functionals for a recent blind test of non-covalent interactions

Benchmark datasets of non-covalent interactions are essential for assessing the performance of density functionals and other quantum chemistry approaches. In a recent blind test, Taylor et al. benchmarked 14 methods on a new dataset consisting of 10 dimer potential energy curves calculated using coupled cluster with singles, doubles, and perturbative triples (CCSD(T)) at the complete basis set (CBS) limit (80 data points in total). Finally, the dataset is particularly interesting because compressed, near-equilibrium, and stretched regions of the potential energy surface are extensively sampled.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

HP-TACO: A high-pressure triaxial compression apparatus for in situ x-ray measurements in geomaterials

Triaxial compression experiments are commonly used to characterize the elastic and inelastic behavior of geomaterials. In situ measurements of grain kinematics, particle breakage, stresses, and other microscopic phenomena have seldom been made during such experiments, particularly at high pressures relevant to many geologic and man-made processes, limiting our fundamental understanding. To address this issue, we developed a new triaxial compression device called HP-TACO (High-Pressure TriAxial COmpression Apparatus). HP-TACO is a miniaturized, conventional triaxial compression apparatus permitting confining pressures up to 50 MPa and deviatoric straining of materials, while also allowing in situ x-ray measurements of grain-scale kinematics and stresses. Here, in this study, we present the design of and first results from HP-TACO during its use in laboratory and synchrotron settings to study grain-scale kinematics and stresses in triaxially compressed sands subjected to 15 and 30 MPa confining pressures. The data highlight the unique capabilities of HP-TACO for studying the high-pressure mechanics of sands, providing new insight into micromechanical processes occurring during geologic and man-made processes.

47 OTHER INSTRUMENTATION↗

Phase diagram and edge states of the 𝜈 = 5/2 fractional quantum Hall state with Landau level mixing and finite well thickness

The 𝜈 = 5/2 fractional quantum Hall effect is a system of intense experimental and theoretical interest as its ground state may host non-Abelian excitations, but the exact nature of the ground state is still undetermined. We present the results of an exact diagonalization study of an electron system in the disk configuration, including the effects of Landau level (LL) mixing and the finite thickness of the quantum well confining the electrons. The degeneracy between the two leading candidates for the ground state, the Pfaffian and anti-Pfaffian, is broken by interactions with a neutralizing background, in addition to the inclusion of two- and three-body interactions via LL mixing. As a result of the neutralizing background in the disk configuration, there is a phase transition from the anti-Pfaffian to the Pfaffian as LL mixing is turned on, in stark contrast to what is observed in spherical geometry. This behavior is in agreement with existing experiments, showing the appearance of the Pfaffian state at strong LL mixing before the system enters a compressible phase. Furthermore, the inclusion of LL mixing leads to an increased charge 𝑒/4 quasihole size. LL mixing interactions are also shown to overcome the effects of edge reconstruction. Due to finite thickness effects, these properties are enhanced dramatically. We also find that only the Pfaffian and anti-Pfaffian states continue to possess energy gaps at finite width, while gaps for compressible stripe states close, which is in agreement with available experimental data.

Tylan-Tyler, Anthony↗

Extraction of tumor motion trajectories using PICCS-4DCBCT: A validation study

Purpose: As a counterpart of 4DCT in the treatment planning stage of radiotherapy treatment, 4D cone beam computed tomography (4DCBCT) method has been proposed to verify tumor motion trajectories before radiation therapy treatment delivery. Besides 4DCBCT acquisition using slower gantry rotation speed or multiple rotations, a new method using the prior image constrained compressed sensing (PICCS) image reconstruction method and the standard 1-min data acquisition were proposed. In this paper, the PICCS-4DCBCT method was combined with deformable registration to validate its capability in motion trajectory extraction using physical phantom data, simulated human subject data from 4DCT and in vivo human subject data. Methods: Two methods were used to validate PICCS-4DCBCT for the purpose of respiratory motion delineation. The standard 1-min gantry rotation Cone Beam CT acquisition was used for both methods. In the first method, 4DCBCT projection data of a physical motion phantom were acquired using an on-board CBCT acquisition system (Varian Medical Systems, Palo Alto, CA). Using a deformable registration method, the object motion trajectories were extracted from both FBP and PICCS reconstructed 4DCBCT images, and compared against the programmed motion trajectories. In the second method, using a clinical 4DCT dataset, Cone Beam CT projections were simulated by forward projection. Using a deformable registration method, the tumor motion trajectories were extracted from the reconstructed 4DCT and PICCS-4DCBCT images. The performance of PICCS-4DCBCT is assessed against the 4DCT ground truth. The breathing period was varied in the simulation to study its effect on motion extraction. For both validation methods, the root mean square error (RMSE) and the maximum of the errors (MaxE) were used to quantify the accuracy of the extracted motion trajectories. After the validation, a clinical dataset was used to demonstrate the motion delineation capability of PICCS-4DCBCT for human subjects. Results: In both validation studies, the RMSEs of the extracted motion trajectories from PICCS-4DCBCT images are less than 0.7 mm, and their MaxEs are less than 1 mm, for all three directions. In comparison, FBP-4DCBCT shows considerably larger RMSEs in the physical phantom based validation. PICCS-4DCBCT also shows insensitivity to the breathing period in the 4DCT based validation. For the in vivo human subject study, high quality 3D motion trajectory of the tumor was obtained from PICCS-4DCBCT images and showed consistency with visual observation. Conclusions: These results demonstrate accurate delineation of tumor motion trajectory can be achieved using PICCS-4DCBCT and the standard 1-min data acquisition.

61 RADIATION PROTECTION AND DOSIMETRY↗

Elevated and Low Temperature Deformation of Cast Depleted Uranium

Goals: Understand crystal structure and micro-structure changes during high and low temperature deformation of uranium, in particular texture, and develop constitutive micro-structure based model for uranium deformation. Deliverables achieved: Completed texture measures for 11 pre- and post-dU compression samples, quantified texture pre- and post-deformation, and provided data to constrain deformation models.

Materials Science(36)↗

Quarterly Research Performance Progress Report (Q8)

As part of Task 1, we have started by testing our modeling capabilities by reproducing isothermal DFIT simulations presented in the literature. Once satisfied with the results we have started by targeting the modeling of the DFITs at conducted at well 58-32. We have a identified a specific test (cycle 4 in zone 2) as the most interesting to be model with GEOS hydraulic fracturing module. Thus, we have first produced results with an isothermal model and adjusted model parameters to get a satisfying match with field pressure data. The, we have added thermal effects and compared the modeling results with and without thermal effects to estimate how thermal effects may influence test interpretation. Models seem to suggest that, for small volumes of fluid, thermal effects are moderate. In Task 2, we have adapted GEOS phase-field formulation to be able to simulate near-wellbore hydraulic fracture nucleation and propagation. We have devised a novel formulation that, compared to other existing ones, incorporates rock strengths. We have submitted a journal publication about our work. We are currently employing this phase-field formulation to model the experiments taking place at U Pitt and help us understand the effect of various parameters. In Task 3, we have built a model of the region surround well 16A and have started modeling stage 3 stimulation because of its simpler planar geometry. After calibrating simulation parameters using known analytical solutions, we have simulated the stage 3 stimulation using our isothermal hydraulic fracturing module, varying the permeability field, the stress conditions including different physics to get a better understanding of the numerical challenges and of the effects of varying these parameters on the simulation results. In Task 4 laboratory experimentation, a set of specialized drilling and injection tools has been customized and constructed to accommodate an inclined well with an orientation of up to 30 degrees relative to material anisotropy or principal stress axes. These inclined samples have also undergone thermal stress and hydraulic fracturing at a temperature of 190 degrees Celsius. Furthermore, both vertical and deviated sampling testing setups enable an extended analysis of post-peak pressure behaviors, facilitating post-test pressure analyses such as the G-function, step rate, and fracture reopening measurements. Thus, the key components of in-situ stress estimation can be extracted and validated through our experiment, providing a solid foundation for validating existing in-situ stress estimation theories or proposing new ones. Simultaneously, we are integrating computer vision techniques with traditional experimental fracture observation methods such as multi-overcore/slicing and water-penetration fracture observation. This combination will prove beneficial in populating the hydraulic fracture patterns database, generated under challenging EGS conditions. This approach aims to deepen our understanding of the complexities in EGS reservoirs and pave the way for future data-driven investigations. Additionally, PITT has also equipped the ELE International compression machine, which is now prepared for conducting indirect tensile and fracture toughness tests. These tests will aid in characterizing how rock fabrics influence the resulting fracture patterns. Additionally, we have completed the required personnel training and gained access to Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) for conducting more detailed characterization and analysis of rock fabrics, as well as the examination of thermal and hydraulically induced fracture patterns. Thus, the PITT team has effectively demonstrated the capabilities of our experimental apparatuses in exploring the thermal effects, well deviation angles, material anisotropy, and operational choices (such as circulation rate, injection fluid viscosity, and injection rate) and their impact on pressure responses and fracture trajectories under the Utah FORGE conditions.

15 GEOTHERMAL ENERGY↗

HPC-FAIR: A Framework Managing Data and AI Models for Analyzing and Optimizing Scientific Applications

The increasing reliance on machine learning (ML) to analyze and optimize large-scale scientific applications on supercomputers faces a significant bottleneck: the lack of readily available, high-quality training datasets and the difficulty in reusing existing AI models. This project was motivated by the urgent need to address the “FAIR” principles (Findability, Accessibility, Interoperability, Reusability) for both training datasets and AI models in the high-performance computing (HPC) domain. The project developed HPC-FAIR, a high-performance computing data management framework designed to centralize HPC-related datasets and AI models within a unified hub. To ensure interoperability, the framework established a standardized representation and vocabulary (ontology) for both data and models. HPC-FAIR also implemented automated workflows to streamline data processing, model access, and benchmarking. Additionally, the project focused on optimizing data harnessing efficiency through advanced techniques like deep reuse and compression-based analytics.

97 MATHEMATICS AND COMPUTING↗

Structure and Behavior of the Ni End-Member Schreibersite Ni 3 P under Compression to 50 GPa

To better understand the potential presence of light element alloys of Fe and Ni in the Earth’s interior, the crystal structure and compressional behavior of the Ni-P binary compound, schreibersite (Ni 3 P), have been investigated using synchrotron X-ray diffraction experiments. Both powder and two single-crystal samples of synthetic Ni 3 P (in different orientations with respect to the loading axis of the diamond anvil cell) were compressed up to approximately 50 GPa at ambient temperature. The compressional data obtained for Ni3P were fitted with a 3rd order Birch–Murnaghan equation of state. All data indicated that the c/a ratio of unit cell parameters remained approximately constant up to about 30 GPa but then increased progressively with pressure, exhibiting a second slight discontinuity at approximately 40 GPa. The changes in unit cell parameters at ~30 GPa and ~40 GPa suggested discontinuous changes in magnetic ordering. Moreover, the threshold of these subtle discontinuities is sensitive to the stress state and orientation of the crystal in the diamond anvil cell. This study is the first report on the compressional behavior of both powder and single-crystal schreibersite at high-pressure (up to 50 GPa). It offers insights into the effects of Ni 3 P components on the compressional behavior of the Earth’s core.

36 MATERIALS SCIENCE↗

Joint Topology Identification and State Estimation in Unobservable Distribution Grids

Many distribution system operations (e.g., state estimation, control, fault detection/localization) rely on the assumption that the underlying topology is accurately defined. In general, topology identification is a challenging problem in distribution systems as these systems are unobservable with a very limited number of available measurements. In this paper, we tackle this problem by designing a compressive sensing framework that jointly estimates the systems states and network topology via an integrated mixed integer nonlinear program (MINLP) formulation. Here, two reformulations of the original MINLP problems are investigated. Firstly, in order to remove the nonlinearity in the MINLP formulation, a mixed integer linear programming (MILP) problem that employs auxiliary variables is derived. Furthermore, to achieve a faster solution, convex relaxation of the original formulation is derived. Finally, using a Markovian model for topology changes, prior information about system topology is used to improve topology identification particularly when a limited amount of measurements is available. Simulation results on IEEE 37-bus test feeder and IEEE 123-bus test feeder illustrate the efficiency and scalability of the proposed approaches from both state estimation and topology identification point of view (even with 30% of available data).

42 ENGINEERING↗

Assessing continuum plasticity postulates with grain stress and local strain measurements in triaxially compressed sand

Critical state and continuum plasticity theories have been used in research and engineering practice in soil and rock mechanics for decades. These theories rely on postulated relationships between material stresses and strains. Some classical postulates include coaxiality between stress and strain rates, stress–dilatancy relationships, and kinematic assumptions in shear bands. Although numerical and experimental data have quantified the strains and grain kinematics in such experiments, little data quantifying grain stresses are available. Here, we report the first-known grain stress and local strain measurements in triaxial compression tests on synthetic quartz sands using synchrotron X-ray tomography and 3D X-ray diffraction. We use these data to examine the micromechanics of shear banding, with a focus on coaxiality, stress-dilatancy, and kinematics within bands. Our results indicate the following: 1) elevated deviatoric stress, strain, and stress ratios in shear bands throughout experiments; 2) coaxial principal compressive stresses and strains throughout samples; 3) significant contraction along shear bands; 4) vanishing volumetric strain but nonvanishing stress fluctuations throughout samples at all stages of deformation. Our results provide some of the first-known in situ stress and strain measurements able to aid in critically evaluating postulates employed in continuum plasticity and strain localization theories for sands.

42 ENGINEERING↗

First-principles calculation of the reflectance of shock-compressed xenon

Within electron density functional theory (DFT), the reflectance of radiation from shock-compressed xenon plasma is calculated. The dependence of the reflectance on the frequency of the incident radiation and on the plasma density is considered. The Fresnel formula is used. The expression for the longitudinal dielectric tensor in the long-wavelength limit is used to calculate the imaginary part of the dielectric function (DF). The real part of the DF is determined by the Kramers-Kronig transformation. The results are compared with experimental data. An approach is proposed to estimate the plasma frequency in shock-compressed xenon.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Compressional behavior of omphacite to 47 GPa

Omphacite is an important mineral component of eclogite. Single crystal synchrotron X-ray diffraction data on natural (Ca,Na)(Mg,Fe,Al)Si 2 O 6 omphacite have been collected at the Advanced Photon Source beamlines 13-BM-C and 13-ID-D up to 47 GPa at ambient temperature. Unit cell parameter and crystal structure refinements were carried out to constrain the isothermal equation of state and compression mechanism. The 3rd order Birch-Murnaghan equation of state (BM3) fit of all data gives V o = 423.9(3) Å3, K To = 116(2) GPa and K To ’ = 4.3(2). These elastic parameters are consistent with the general trend of the diopside-jadeite join. The eight-coordinated polyhedra (M2 and M21) are the most compressible, and contribute to majority of the unit cell compression, while the SiO 4 tetrahedra (Si1 and Si2) behave as rigid structural units and are the most incompressible. Axial compressibilities are determined by fitting linearized BM 3 equation of state to pressure dependences of unit cell parameters. Throughout the investigated pressure range, the b-axis is more compressible than the c-axis. Here, the axial compressibility of the α-axis is the largest among the three axes at 0 GPa, yet it quickly drops to the smallest at pressures above 5 GPa, which is explained by the rotation of the stiffest compression axis toward the a-axis with the increase of pressure.

36 MATERIALS SCIENCE↗