Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CALL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

Single Component Sorption-Desorption Test Experimental Design Approach Discussions

A task was identified within the fission-product-transport work package to develop a path forward for doing testing to determine behavior of volatile fission products behavior and to engage members of the NGNP community to advise and dissent on the approach. The following document is a summary of the discussions and the specific approaches suggested for components of the testing. Included in the summary isare the minutes of the conference call that was held with INL and external interested parties to elicit comments on the approaches brought forward by the INL participants. The conclusion was that an initial non-radioactive, single component test will be useful to establish the limits of currently available chemical detection methods, and to evaluated source-dispersion uniformity. In parallel, development of a real-time low-concentration monitoring method is believed to be useful in detecting rapid dispersion as well as desorption phenomena. Ultimately, the test cycle is expected to progress to the use of radio-traced species, simply because this method will allow the lowest possible detection limits. The consensus of the conference call was that there is no need for an in-core test because the duct and heat exchanger surfaces that will be the sorption target will be outside the main neutron flux and will not be affected by irradiation. Participants in the discussion and contributors to the INL approach were Jeffrey Berg, Pattrick Calderoni, Gary Groenewold, Paul Humrickhouse, Brad Merrill, and Phil Winston. Participants from outside the INL included David Hanson of General Atomics, Todd Allen, Tyler Gerczak, and Izabela Szlufarska of the University of Wisconsin, Gary Was, of the University of Michigan, Sudarshan Loyalka and Tushar Ghosh of the University of Missouri, and Robert Morris of Oak Ridge National Laboratory.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

PG&E WaveConnect Program (Final Report)

The PG&E WaveConnect project was intended to demonstrate the technical and economic viability of wave power in the open ocean adjacent to PG&E's service territory. WaveConnect was conceived as a multi-stage development process leading to long-term megawatt-scale wave power production. The first-stage tasks consisted of site selection, permitting, pilot plant design, and assessment of technology and commercial readiness. The second stage would have included development of infrastructure, undersea cabling, and deployment of wave energy conversion devices (WECs). In the third stage, the most promising WEC devices would have been deployed in larger quantities and connected to the grid. This report documents the findings of Stage One. Site Selection: After studying the wave energy potential, grid interconnection and other project infrastructure along the California coast, PG&E selected two sites: one near Eureka, called the Humboldt WaveConnect (HWC) project, and another near Vandenberg Air Force Base, called the Central Coast WaveConnect project (CCWC).

16 TIDAL AND WAVE POWER↗

Nevada National Security Site Waste Acceptance Criteria

This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept DOE non-radioactive classified waste, DOE non-radioactive hazardous classified waste, DOE low-level radioactive waste (LLW), DOE mixed low-level waste (MLLW), and U.S. Department of Defense (DOD) classified waste for permanent disposal. Classified waste is the only waste accepted for disposal that may be non-radioactive and will be required to meet the waste acceptance criteria for radioactive waste as specified in this document. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project (WMP) at (702) 295-7063, and your call will be directed to the appropriate contact.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Performance of Variable Capacity Heat Pumps in a Mixed Humid Climate

Variable capacity heat pumps represent the next wave of technology for heat pumps. In this report, the performance of two variable capacity heat pumps (HPs) is compared to that of a single or two stage baseline system. The units were installed in two existing research houses located in Knoxville, TN. These houses were instrumented to collect energy use and temperature data while both the baseline systems and variable capacity systems were installed. The homes had computer controlled simulated occupancy, which provided consistent schedules for hot water use and lighting. The temperature control and energy use of the systems were compared during both the heating and cooling seasons. Multiple linear regression models were used along with TMY3 data for Knoxville, TN in order to normalize the effect that the outdoor air temperature has on energy use. This enables a prediction of each system's energy use over a year with the same weather. The first system was a multi-split system consisting of 8 indoor units and a single outdoor unit. This system replaced a 16 SEER single stage HP with a zoning system, which served as the baseline. Data was collected on the baseline system from August 2009 to December 2010 and on the multi-split system from January 2011 to January 2012. Soon after the installation of the multi-split system, some of the smaller rooms began over-conditioning. This was determined to be caused by a small amount of continuous refrigerant flow to all of the indoor units when the outdoor unit was running regardless of whether they were calling for heat. This, coupled with the fact that the indoor fans run continuously, was providing enough heat in some rooms to exceed the set point. In order to address this, the indoor fans were disabled when not actively heating per the manufacturer's recommendation. Based on the measured data, the multi-split system was predicted to use 40% more energy in the heating season and 16% more energy in the cooling season than the baseline system, for the typical meteorological year weather data. The AHRI ratings indicated that the baseline system would perform slightly better than the multi-split system, but not by as large of a margin as seen in this study. The multi-split system was able to maintain more consistent temperature throughout the house than the baseline system, but it did allow relative humidity levels to increase above 60% in the summer. The second system was a split system with an inverter driven compressor and a single ducted air handler. This unit replaced a 16 SEER two stage HP with a zoning system. Data was collected on the baseline system from July 2009 to November 2010 and on the ducted inverter system from December 2010 to January 2012. The ducted inverter system did not offer a zone controller, so it functioned as a single zone system. Due to this fact, the registers had to be manually adjusted in order to better maintain consistent temperatures between the two levels of the house. The predicted heating season energy use for the ducted inverter system, based on the measured energy use, was 30% less than that of the baseline system for the typical meteorological year. However, the baseline system was unable to operate in its high stage due to a wiring issue with the zone controller. This resulted in additional resistance heat use during the winter and therefore higher energy use than would be expected in a properly performing unit. The AHRI ratings would indicate that the baseline system would use less energy than the ducted inverter system, which is opposite to the results of this study. During the cooling season, the ducted inverter system was predicted to use 23% more energy than the baseline system during the typical meteorological year. This is also opposite of the results expected by comparing the AHRI ratings. After a detailed comparison of the ducted inverter system's power use compared to that of a recently installed identical system at a retro-fit study house, there is concern that the unit is not operating as intended. The power use and cycles indicate that the unit is performing more like a single stage unit than a variable capacity unit. Analysis of the data indicates that a change in operating behavior occurred during a service call shortly after the installation of the unit. The logbook only indicates that refrigerant charge was added, but does not indicate any other change. This is being investigated further. While the energy comparison results of these two variable capacity heat pumps is generally underwhelming, it is difficult to draw any hard conclusions about the maximum attainable efficiency of these units when optimally installed. Both units appear to have undesirable conditions associated with the installation or operation, which could have had an adverse effect on their energy use.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Genome-Facilitated Analyses of Geomicrobial Processes

This project had the goal(s) of understanding the mechanism(s) of extracellular electron transport (EET) in the microbe Shewanella oneidensis MR-1, and a number of other strains and species in the genus Shewanella. The major accomplishments included sequencing, annotation, and analysis of more than 20 Shewanella genomes. The comparative genomics enabled the beginning of a systems biology approach to this genus. Another major contribution involved the study of gene regulation, primarily in the model organism, MR-1. As part of this work, we took advantage of special facilities at the DOE: e.g., the synchrotron radiation facility at ANL, where we successfully used this system for elemental characterization of single cells in different metabolic states (1). We began work with purified enzymes, and identification of partially purified enzymes, leading to initial characterization of several of the 42 c-type cytochromes from MR-1 (2). As the genome became annotated, we began experiments on transcriptome analysis under different conditions of growth, the first step towards systems biology (3,4). Conductive appendages of Shewanella, called bacterial nanowires were identified and characterized during this work (5, 11, 20,21). For the first time, it was possible to measure the electron transfer rate between single cells and a solid substrate (20), a rate that has been confirmed by several other laboratories. We also showed that MR-1 cells preferentially attach to cells at a given charge, and are not attracted, or even repelled by other charges. The interaction with the charged surfaces begins with a stimulation of motility (called electrokinesis), and eventually leads to attachment and growth. One of the things that genomics allows is the comparative analysis of the various Shewanella strains, which led to several important insights. First, while the genomes predicted that none of the strains looked like they should be able to degrade N-acetyl glucosamine (NAG), the monomer that makes up chitin, virtually all of the strains were in fact capable. This led to the discovery of a great many new genes involved with chitin and NAG metabolism (7). In a similar vein, a detailed study of the sugar utilization pathway revealed a major new insight into the regulation of sugar metabolism in this genus (19). Systems Biology and Comparative Genomics of the shewanellae: Several publications were put together describing the use of comparative genomics for analyses of the group Shewanella, and these were a logical culmination of our genomic-driven research (10,15,18). Eight graduate students received their Ph.D. degrees doing part of the work described here, and four postdoctoral fellows were supported. In addition, approximately 20 undergraduates took part in projects during the grant period.

54 ENVIRONMENTAL SCIENCES↗

Maltose Biochemistry and Transport in Plant Leaves

Starch is a desirable plant product for both food and biofuel. Leaf starch is ideal for use in biofuels because it does not compete with grain starch, which is used for food. Starch is accumulated in plant leaves during the day and broken down at night. If we can manipulate leaf starch breakdown it may be possible to design a plant that provides both grain starch for food and leaf starch for biofuel. The pathway of leaf starch breakdown was not known when this work started. Preliminary evidence had shown that maltose was the primary product of leaf starch breakdown (Weise, Weber & Sharkey, 2004) and that it was metabolized by a disproportionating enzyme called amylomaltase but given the initials DPE2 (Lu & Sharkey, 2004). In this work we showed that only one form of maltose was metabolically active (Weise et al., 2005a) and that maltose was located in two different places when the amylomaltase was knocked out but only inside the chloroplast when the maltose transporter was knocked out (Lu et al., 2006a). This allowed us to estimate the energetics of maltose export and to show that maltose export is more efficient than glucose export (Weise et al., 2005b). We examined how daylength affected starch breakdown rate and found that starch breakdown rate could respond to changes in daylength within one day (Lu, Gehan & Sharkey, 2005). We also were able to show a second starch breakdown pathway by chloroplastic starch phosphorylase (Weise et al., 2006). Work to this point was summarized in a review (Lu & Sharkey, 2006). We were able to show that the amylomaltase in plants could substitute for the amylomaltase in bacteria (Lu et al., 2006b). In this paper we also showed the importance of a second enzyme called alpha-glucan phosphorylase in starch breakdown. Finally, we were able to determine the enzymatic mechanism of the amylomaltase (Steichen, Petty & Sharkey, 2008). These results have laid the groundwork for manipulating plants for improved biofuel production.

09 BIOMASS FUELS↗

Commercialization of New Lattice-Matched Multi-Junction Solar Cells Based on Dilute Nitrides: July 8, 2010 - March 7, 2012

All the milestones for this program were achieved and in most cases, particularly those related to cell performance, more samples were supplied than was required, and the deliverables substantially exceed the performance milestones. Moreover, the cell deliverables sent to NREL for evaluation were cells 4 mm or 5.5 mm, nearly 5 to 10 times larger in area than the 2 mm cells called for in the subcontract, and one of the most common sizes in the CPV industry. For the entire program there were 12 separate cell performance milestones, the most important of which was the 3J cell efficiency. Phase 1 had 2 3J efficiency milestones and Phase 2 had three. For the Phase 1 milestone calling for 38% efficiency, NREL measured a peak efficiency of 41.1%, about 2% higher than the data sheet values of commercial cells at that time. The efficiencies measured in Phase 1 exceed the Phase 2 cell performance milestones in the subcontract’s original Statement of Work. Cells submitted to NREL as part of this subcontract, although not as deliverables, were measured to have a new World Record cell efficiency of 43.5%, breaking the previous World Record by 1.2% absolute. In addition to improved cell performance, during Phase 1 a modeling capability for designing ARCs was developed and verified by comparing the measured current from a cell using a specific ARC with the current predicted by the model. This model was then used to design a new ARC giving lower reflectivity and a corresponding higher cell current. Again the prediction of the model was verified by measured cell properties. In Phase 2, the modeling capability was used to design a glass matched ARC, the type most in use in the CPV industry, which was tuned to the band structure of a 3J cell with a dilute nitride bottom cell. Finally, tools and test methodologies were developed that enable HALT to be applied to cells to determine the operating and destruct limits and to determine or set bounds on the lifetime of the cells in typical CPV operating conditions. As part of this effort a novel HALT system was built that enabled cells to be subjected to light at concentrations up to 80 W/cm 2 , (800 suns) while the cell temperature could be held or cycled between -100C and +180C. As part of the Phase 2 effort the system was modified to enable the light to the cell to be interrupted at a maximum rate of 10 times/second. Tests using interrupted light at >500 suns on cells held at 180C showed no evidence of failure after a total of >22 sun-years of operation at 100C. Another key outcome of the reliability efforts of the program was from high temperature storage tests done independently of the HALT test. There were two key outcomes of this activity: 1) single junction GaInNAs cells showed no evidence of failure under the equivalent of at least 100 years of on-sun time operating at 100C and 2) we can conclude with 95% confidence that the probability of device failure after 30 sun-years of operation at 100C is less than 1.5%, and mostly less than 0.5%. Based on these results there is no reason to believe that dilute nitrides in and of themselves pose a reliability problem for CPV applications and that 3J cells using dilute nitrides have very low probability of failure during the expected 20-30 year life of a CPV power plant.

14 SOLAR ENERGY↗

Designer Phase Transitions in Lithium-Based Spinels (Final Report)

When electrons in a metal become correlated with each other, new cooperative behavior can arise. This correlation is magnified when the metal has magnetic ions embedded in it. These atomic magnets try to line up with each other, but in doing so actually create a correlation between the motions of conduction electrons. In turn, these correlated electron motions prevent the magnetic ions from aligning, even at zero Kelvin. When this competition is strongest (at the so-called quantum critical point-QCP) the response of the system can no longer be described using the text book theory for metals. In addition, a range of new phenomena has been seen to emerge in the vicinity of a QCP, such as heavy-fermion superconductivity, coexistence of magnetism and superconductivity and hyper-scaling. The main goal of our research is to try to unravel the details of the feedback mechanism between electron motion and magnetism that lies at the heart of this new physics. We have chosen lithium-based spinel structures as the most promising family of systems to achieve our goal. Known lithium-based spinels Li x M 2 O 4 [M=V, Ti and Mn] show a variety of ground states: heavy-fermion, superconducting, or geometrically frustrated local moment systems. Li x M 2 O 4 should be ideal systems for studying QCPs since their properties can easily be fine-tuned, simply by extracting some Li [which can be done without introducing disorder in the immediate surroundings of the magnetic ions]. The premise of the proposal was that since this Li-extraction can be done both in the metallic as well as in insulating compounds, that we can expand the types of quantum phase transitions that can be studied to beyond transitions in magnetic metals. The project called for developing a better understanding of quantum phase transitions by measuring all aspects of the electronic response of Li x M 2 O 4 by means of neutron scattering, giving microscopic information about the behavior of the individual magnetic moments and their interactions, as well as by macroscopic measurements. In addition, the aim was to synthesize new lithium-based spinel compounds by using other transition metals that exhibit both 3 + and 4 + valencies. Here we report on the progress we have made during the course of this grant both towards the stated goals and on new avenues that developed as a direct result of the data we collected during this grant.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Institutional Computing (IC) Information Session [Slides]

The LANL Institutional Computing Program (IC) will host an information session about the current state of unclassified Institutional Computing at Los Alamos, exciting plans for the future, and the current call for proposals for science and engineering projects requiring computing. Program representatives will give short presentations and field questions about the call for proposals and future planned machines, and discuss technical support available to existing and future projects. Los Alamos has started making a serious institutional investment in open computing available to our science projects, and that investment is expected to increase even more.

99 GENERAL AND MISCELLANEOUS↗

Eastern Interconnection Demand Response Potential

Demand response (DR), one of the key components in the Smart Grid initiative, has received increasing interest in recent years among power utilities, independent system operators, and policy makers. With this surge of interest in DR, in April 2010 the Department of Energy (DOE) issued a research call to provide technical support to the interconnection-level electric infrastructure planning projects they had issued earlier in the year. In Area of Interest 2, they identified a need/purpose: “The Eastern Interconnection States’ Planning Council (EISPC) seeks to significantly improve the knowledge base and modeling capabilities of demand-side resources for purposes of transmission planning.” In response to the research call, Oak Ridge National Laboratory (ORNL) conducted a research project to estimate the DR potential peak load reductions in the Eastern Interconnection area over the next two decades until 2030, as well as analyzed costs and benefits occurring out of the DR resources. This final report is the outcome of the study by a team of ORNL researchers with diverse backgrounds in engineering, economics, and public policy.

demand response↗

combinatorial optimization with demands (LDRD Final Report)

This report summarizes the research conducted and results obtained under the Laboratory Directed Research and Development (LDRD) project, “Combinatorial Optimization with Demands ,” from October 2010 to September 2012. Complex resource allocation problems are ubiquitous in mission-driven applications. We investigated resource allocation problems endowed with additional parameters called demands, which allow for richer modeling. Demand endowed resource allocation problems are considerably harder to solve than their traditional counterparts, and we developed a conceptually simple but powerful new framework called iterative packing which allowed us to address the added complexity of demands. By leveraging iterative packing , we designed approximation algorithms to solve a large class of hard resource allocation problems with demands. Approximation algorithms are efficient heuristics which also offer a performance guarantee on the worst case deviation from the cost of an optimal solution. Our algorithms offer better performance guarantees over previously known algorithms; moreover, we are able to show that our algorithms provide performance guarantees that are likely close to best possible.

Parekh, Ojas↗

Thin, High Lifetime Silicon Wafers with No Sawing; Re-crystallization in a Thin Film Capsule

The project fits within the area of renewable energy called photovoltaics (PV), or the generation of electricity directly from sunlight using semiconductor devices. PV has the greatest potential of any renewable energy technology. The vast majority of photovoltaic modules are made on crystalline silicon wafers and these wafers accounts for the largest fraction of the cost of a photovoltaic module. Thus, a method of making high quality, low cost wafers would be extremely beneficial to the PV industry. The industry standard technology creates wafers by casting an ingot and then sawing wafers from the ingot. Sawing rendered half of the highly refined silicon feedstock as un-reclaimable dust. Being a brittle material, the sawing is actually a type of grinding operation which is costly both in terms of capital equipment and in terms of consumables costs. The consumables costs associated with the wire sawing technology are particularly burdensome and include the cost of the wire itself (continuously fed, one time use), the abrasive particles, and, waste disposal. The goal of this project was to make wafers directly from molten silicon with no sawing required. The fundamental concept was to create a very low cost (but low quality) wafer of the desired shape and size and then to improve the quality of the wafer by a specialized thermal treatment (called re-crystallization). Others have attempted to create silicon sheet by recrystallization with varying degrees of success. Key among the difficulties encountered by others were: a) difficulty in maintaining the physical shape of the sheet during the recrystallization process and b) difficulty in maintaining the cleanliness of the sheet during recrystallization. Our method solved both of these challenges by encapsulating the preform wafer in a protective capsule prior to recrystallization (see below). The recrystallization method developed in this work was extremely effective at maintaining the shape and the cleanliness of the wafer. In addition, it was found to be suitable for growing very large crystals. The equipment used was simple and inexpensive to operate. Reasonable solar cells were fabricated on re-crystallized material.

14 SOLAR ENERGY↗

Trinitromethyl Heterocycle Oxidizers as a Solid Propellant Ingredient

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Physical Sciences, Inc. (PSI), to develop a synthesis of two novel energetic heterocyclic oxidizers as possible replacements for ammonium perchlorate (AP) in rocket propellant formulations. This CRADA resulted from the award of the Phase I Small Business Technology Transfer (STTR) from DOD. The CRADA consisted of two phases. The goal for Phase 1 was to produce a new oxidizer called TNMDNP. Phase 2 is optional (based on the success of Phase 1) and the goal of Phase 2 (optional) was to produce a new oxidizer called TNMDNT. Phase 2 tasks would be performed based on the successful results of Phase 1.

Pagoria, Phillip↗

Recovery Act: Finite Volume Based Computer Program for Ground Source Heat Pump Systems

This report is a compilation of the work that has been done on the grant DE-EE0002805 entitled Finite Volume Based Computer Program for Ground Source Heat Pump Systems. The goal of this project was to develop a detailed computer simulation tool for GSHP (ground source heat pump) heating and cooling systems. Two such tools were developed as part of this DOE (Department of Energy) grant; the first is a two-dimensional computer program called GEO2D and the second is a three-dimensional computer program called GEO3D.

15 GEOTHERMAL ENERGY↗

A Path to Operating System and Runtime Support for Extreme Scale Tools

In this project, we cast distributed resource access as operations on files in a global name space and developed a common, scalable solution for group operations on distributed processes and files. The resulting solution enables tool and middleware developers to quickly create new scalable software or easily improve the scalability of existing software. The cornerstone of the project was the design of a new programming idiom called group file operations that eliminates iterative behavior when a single process must apply the same set of file operations to a group of related files. To demonstrate our novel and scalable ideas for group file operations and global name space composition, we developed a group file system called TBON-FS that leverages a tree-based overlay network (TBON), specifically MRNet, for logarithmic communication and distributed data aggregation. We also developed proc++, a new synthetic file system co-designed for use in scalable group file operations. Over the course of the project, we evaluated the utility and performance of group file operations, global name space composition, TBON-FS, and proc++ in three case studies. The first study focused on the ease in using group file operations and TBON-FS to quickly develop several new scalable tools for distributed system administration and monitoring. The second study evaluated the integration of group file operation and TBON-FS within the Ganglia Distributed Monitoring System to improve its scalability for clusters. The final study involved the integration of group file operations, TBON-FS, and proc++ within TotalView, the widely-used parallel debugger. For this project, the work of the Oak Ridge National Laboratory (ORNL) team occurred primarily in two directions: bringing the MRNet tree-based overlay network (TBON) implementation to the Cray XT platform, and investigating techniques for predicting the performance of MRNet topologies on such systems. Rogue Wave Software (RWS), formerly TotalView Technologies Inc., worked with the University ofWisconsin (UW) team on the design and prototyping of a scalable version of the TotalView debugger. RWS assisted UW with their "proc++" design effort. RWS assisted UW with strategy for integrating proc++ into TotalView.

97 MATHEMATICS AND COMPUTING↗

LDRD 2009 Annual Report: Laboratory Directed Research and Development Program Activities

Each year, Brookhaven National Laboratory (BNL) is required to provide a program description and overview of its Laboratory Directed Research and Development Program (LDRD) to the Department of Energy in accordance with DOE Order 413.2B dated April 19, 2006. This report provides a detailed look at the scientific and technical activities for each of the LDRD projects funded by BNL in FY2009, as required. In FY2009, the BNL LDRD Program funded 57 projects, 6 of which were new starts, at a total cost of $\$$11,671,567. Approximately 25% of the total funds was invested in a focused FY2009 LDRD call for proposals, and the remaining ~75% was awarded to openly competed LDRD projects. The investments that BNL makes in its LDRD program largely support the Laboratory’s strategic goals as outlined in the BNL Laboratory Plan. BNL has five Laboratory Initiatives, Photon Sciences, QCD Matter, Energy, Physics of the Universe, and Bio/Climate and Environmental Sciences. These major initiatives support the growth and evolution of the major business lines (i.e. mission areas) of the Laboratory. In addition, there are three smaller initiatives that support growth and program development in targeted areas, i.e. Biological Imaging, Computation, and Detectors for National Security. Approximately 88% of BNL LDRD funds supported one of the major or targeted initiatives. Of this, about 58% supported the five major initiatives and about 30% supported the smaller initiatives. About 12% was invested in other innovative research and development activities. In total, these LDRD investments supported 105 postdoctoral researchers and graduates students in whole or in part. In FY2009, new LDRD investments (5 of the 6 new projects started) largely supported the BNL initiative in Energy; $\$$3.465M supported projects started in FY2009, of which $\$$2.974M funded the focused call for proposals in Energy R&D.

99 GENERAL AND MISCELLANEOUS↗