Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ATTITUDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,243 records · Page 69

An attitude reorientation algorithm for the Galileo spacecraft

This paper presents an onboard closed loop attitude reorientation algorithm for a dual-spin spacecraft, Galileo. The basic concept for the design uses the despun stator as a reference and fires a sequence of fixed duration thruster pulses to precess the angular momentum vector to its commanded orientation. The error signals used to despin the stator and to perform the turn are derived from the stator error quaternion which is computed using gyro outputs. Constraints considered in the design include gyro rate saturation, plume impingement effects, system parameter variations, as well as software reliability and flexibility. The performance of the algorithm was predicted by analysis and confirmed by computer simulation results. It was concluded that a reorientation accuracy of better than 1 milliradian with a nutation angle of less than 1 degree during the turn can be achieved.

Lin, H.-S.↗

Determining Calibration Constants for Attitude Measurements

Algorithm based on method of least squares determines calibration constants of seismic instruments for precise attitude measurements. Algorithm programed and run successfully on commercially available desk-top computer. Simplifies determinations of accelerometer calibration constants, and used in field to verify accelerometer stability.

Tcheng, P.↗

Modular design attitude control system

A sequence of single axismodels and a series of reduced state linear observers of minimum order are used to reconstruct inaccessible variables pertaining to the modular attitude control of a rigid body flexible suspension model of a flexible spacecraft. The single axis models consist of two, three, four, and five rigid bodies, each interconnected by a flexible shaft passing through the mass centers of the bodies. Modal damping is added to each model. Reduced state linear observers are developed for synthesizing the inaccessible modal state variables for each modal model.

Chichester, F. D.↗

Preliminary performance of a vertical-attitude takeoff and landing, supersonic cruise aircraft concept having thrust vectoring integrated into the flight control system

A performance study was made of a vertical attitude takeoff and landing (VATOL), supersonic cruise aircraft concept having thrust vectoring integrated into the flight control system. Those characteristics considered were aerodynamics, weight, balance, and performance. Preliminary results indicate that high levels of supersonic aerodynamic performance can be achieved. Further, with the assumption of an advanced (1985 technology readiness) low bypass ratio turbofan engine and advanced structures, excellent mission performance capability is indicated.

Robins, A. W.↗

Some Aspects of Attitude Stability of Tethered Space Stations

The stability of attitude motion of space stations composed by platforms connected tethers is studied. The motion is assumed to be three dimensional and the station rigid. First, the well known linearized theory is adopted and the location of different configurations in the stability chart is found; second, a destabilizing feature of finite amplitude motion is outlined as a function of inertia parameters.

Bergamasui, S.↗

Developing sensitivity coefficients for a state variable model of a flexible spacecraft with modular attitude control

The numerical value for the sensitivity coefficient of each scalar state variable with respect to each parameter of a five body model of the rotational dynamics of a flexible spacecraft with modular attitude control is generated. The maximum magnitudes of these sensitivity coefficients are arranged in descending order in one table while the final time (steady state) values of these sensitivity coefficients are arranged in order of descending magnitude in a second table.

Chichester, F. D.↗

Computer program for post-flight evaluation of the control surface response for an attitude controlled missile

A FORTRAN IV coded computer program is presented for post-flight analysis of a missile's control surface response. It includes preprocessing of digitized telemetry data for time lags, biases, non-linear calibration changes and filtering. Measurements include autopilot attitude rate and displacement gyro output and four control surface deflections. Simple first order lags are assumed for the pitch, yaw and roll axes of control. Each actuator is also assumed to be represented by a first order lag. Mixing of pitch, yaw and roll commands to four control surfaces is assumed. A pseudo-inverse technique is used to obtain the pitch, yaw and roll components from the four measured deflections. This program has been used for over 10 years on the NASA/SCOUT launch vehicle for post-flight analysis and was helpful in detecting incipient actuator stall due to excessive hinge moments. The program is currently set up for a CDC CYBER 175 computer system. It requires 34K words of memory and contains 675 cards. A sample problem presented herein including the optional plotting requires eleven (11) seconds of central processor time.

Knauber, R. N.↗

The Orbiter camera payload system's large-format camera and attitude reference system

The Orbiter camera payload system (OCPS) is an integrated photographic system carried into earth orbit as a payload in the Space Transportation System (STS) Orbiter vehicle's cargo bay. The major component of the OCPS is a large-format camera (LFC), a precision wide-angle cartographic instrument capable of producing high-resolution stereophotography of great geometric fidelity in multiple base-to-height ratios. A secondary and supporting system to the LFC is the attitude reference system (ARS), a dual-lens stellar camera array (SCA) and camera support structure. The SCA is a 70 mm film system that is rigidly mounted to the LFC lens support structure and, through the simultaneous acquisition of two star fields with each earth viewing LFC frame, makes it possible to precisely determine the pointing of the LFC optical axis with reference to the earth nadir point. Other components complete the current OCPS configuration as a high-precision cartographic data acquisition system. The primary design objective for the OCPS was to maximize system performance characteristics while maintaining a high level of reliability compatible with rocket launch conditions and the on-orbit environment. The full OCPS configuration was launched on a highly successful maiden voyage aboard the STS Orbiter vehicle Challenger on Oct. 5, 1984, as a major payload aboard the STS-41G mission.

Schardt, B. B.↗

Subsystem testing of Galileo's attitude and articulation control fault protection

This paper discusses the fault protection tesing of the Attitude and Articulation Control Subsystem (AACS) of the Galileo spacecraft. The need for an autonomous fault protection system on an interplanetary spacecraft is discussed. Galileo requirements for the detection and response of specific hardware failures is discussed along with the fault protection software design and implementation. The test beds and test methods used for fault protection testing are described. The paper concludes with a presentation of the results of this testing with an emphasis on requirement and design changes that were made as a result of these tests.

Anderson, L. L.↗

Helicopter gust alleviation, attitude stabilization, and vibration alleviation using individual-blade-control through a conventional swash plate

The novel active control system presented for helicopter rotor aerodynamic and aeroelastic problems involves the individual control of each blade in the rotating frame over a wide range of frequencies (up to the sixth harmonic of rotor speed). This Individual Blade Control (IBC) system controls blade pitch by means of broadband electrohydraulic actuators attached to the swash plate (in the case of three blades) or individually to each blade, using acceleratometer signals to furnish control commands to the actuators. Attention is given to IBC's application to blade lag, flapping, and bending dynamics. It is shown that gust alleviation, attitude stabilization, vibration alleviation, and air/ground resonance suppression, are all achievable with a conventional helicopter swash plate.

Ham, N. D.↗

A robust nonlinear attitude control law for space stations with flexible structural components

In this paper, a nonlinear attitude control law for space stations with flexible structural components is derived using a rigid-body model. This control law, depending on the Cayley-Rodriguez parameters, globally stabilizes the equilibrium of the rigid-body model. The effect of elastic deformations of the flexible structural components on the resulting feedback system dynamics is analyzed. It is found that the system's stability property is highly robust with respect to structural vibrations and inertial variations. The time-domain behavior of the feedback system is studied numerically using a model of a typical space station with flexible solar panels.

Wang, P. K. C.↗

A linear quadratic tracker for Control Moment Gyro based attitude control of the Space Station

The paper discusses a design for an attitude control system for the Space Station which produces fast response, with minimal overshoot and cross-coupling with the use of Control Moment Gyros (CMG). The rigid body equations of motion are linearized and discretized and a Linear Quadratic Regulator (LQR) design and analysis study is performed. The resulting design is then modified such that integral and differential terms are added to the state equations to enhance response characteristics. Methods for reduction of computation time through channelization are discussed as well as the reduction of initial torque requirements.

Kaidy, J. T.↗

Single step optimization of feedback-decoupled spacecraft attitude maneuvers

A next-state optimization technique for monitoring spacecraft maneuvers is examined. The optimization technique permits simultaneous trajectory planning and tracking, incorporates actuator saturation and attitude constraints, and prevents overshoot and undershoot. The global linearization of the dynamics and kinematics for a spacecraft driven by reaction wheels is considered. The equations utilized to derive the spacecraft trajectories are presented. The applications of the next-state optimization procedure to a spacecraft maneuvered by momentum transfer devices and the tracking of the nominal trajectory of a critically damped harmonic oscillator response are described.

Dwyer, T. A. W., III↗

Attitude control system synthesis for the Hoop/Column antenna using the LQG/LTR method

This paper investigates the application of the linear-quadratic-Gaussian (LQG)/loop transfer recovery (LTR) method to the problem of synthesizing a fine-pointing control system for a large flexible space anenna. The study is based on an antenna, which consists of three rigid-body rotational modes and the first ten elastic modes. A robust compensator design for achieving the required pointing performance in the presence of modeling uncertainties is obtained using the LQG/LTR method. For the Hoop/Column antenna, a satisfactory controller design meeting a desired bandwidth of .1 rad/sec and ensuring stability with unmodelled high frequency modes is obtained using only a collocated pair of 3-axis attitude sensors and torque actuators. This study also indicates that to achieve the desired performance bandwidth of 0.1 rad/sec. and to ensure stability in the presence of higher frequency elastic modes, the design model should include at least the first three flexible modes together with the rigid body modes.

Sundararajan, N.↗

Three-Axis Attitude Control With a Single Wheel

Single-device attitude-control system provides stabilization along three axes. Flywheel connected to electronically controlled motor rotates on magnetic bearing. At high rotational speed, small angular displacements about x and y axes, in response to control signals enable storage of relatively large amounts of angular momentum. Angular momentum about z axis stored in changes in rotational speed.

Studer, P. A.↗

Structural dynamics and attitude control study of early manned capability space station configurations

A study was performed to determine the vibration and attitude control characteristics of critical space station configurations featuring early manned capability during buildup from initial user support through the operations capability reference station. Five configurations were selected and were examined thus determining the changes that are likely to occur in the characteristics of the system as the station progresses from a single boom structure to a mature, dual keel, operations capability reference station. Both 9 foot and 5 meter truss bay sizes were investigated. All configurations analyzed were stable; however, the 5 meter truss bay size structure exhibited superior stability characteristics.

Ayers, J. Kirk↗

Satellite attitude motion models for capture and retrieval investigations

The primary purpose of this research is to provide mathematical models which may be used in the investigation of various aspects of the remote capture and retrieval of uncontrolled satellites. Emphasis has been placed on analytical models; however, to verify analytical solutions, numerical integration must be used. Also, for satellites of certain types, numerical integration may be the only practical or perhaps the only possible method of solution. First, to provide a basis for analytical and numerical work, uncontrolled satellites were categorized using criteria based on: (1) orbital motions, (2) external angular momenta, (3) internal angular momenta, (4) physical characteristics, and (5) the stability of their equilibrium states. Several analytical solutions for the attitude motions of satellite models were compiled, checked, corrected in some minor respects and their short-term prediction capabilities were investigated. Single-rigid-body, dual-spin and multi-rotor configurations are treated. To verify the analytical models and to see how the true motion of a satellite which is acted upon by environmental torques differs from its corresponding torque-free motion, a numerical simulation code was developed. This code contains a relatively general satellite model and models for gravity-gradient and aerodynamic torques. The spacecraft physical model for the code and the equations of motion are given. The two environmental torque models are described.

Cochran, John E., Jr.↗